Search Documents

By R. I. Jaffee, J. G. Dunleavy, W. Hodge, H. R. Ogden

IN a search for an improved conductor for use in field wire for the L. S. Army Signal Corps, an alloy of copper and silver was developed from which it was possible to obtain 29 B & S ga. strands with tensile strengths in excess of 160,000 psi combined with an electrical conductivity of over 70 pct IACS. Such a favorable combination of strength and electrical conductivity has not been reported previously in the rather extensive literature covering this subject. The properties obtained from various binary alloys of copper and silver, together with the method of fabrication of these alloys which has been developed to obtain the properties desired in fine wire strands, are discussed in this paper. LITERATURE The effect on the electrical conductivity of copper of the various elements in solid solution is shown in Fig I, taken from published data by J. O. Linde and others.' It will be noted that silver in solid solution depresses the electrical conductivity to a lesser extent than any other element for which data are given, and is followed rather closely by cadmium, and then by chromium. Zinc, which lies between cadmium and chromium, has so high a solid solubility in copper that the data for zinc are scarcely comparable to the data for the other two in the range covered. Not many data are available on the strain hardening of copper-rich Cu-Ag alloys. Corson2 reports a 3 pct Ag alloy properly cold worked and annealed to have 100,000 psi tensile strength and 90 pct IACS conductivity. On straight cold working, Hessenbruch3 reports 101.000 psi for a 5 pct Ag, 0.3 pct Be alloy, and 129,000 psi for a 30 pct Ag, 0.5 pct Be alloy. Here it would he expected that much of the strain hardening came from the silver content of the alloys. The copper-rich side of the Cu-Ag diagram, according to Stockdale,4 is shown in the upper part of Fig 2. The electrical conductivities for copper-silver alloys annealed at 750 and 350°C, taken from the work of Johansson and Linde,5 are shown in the lower part of Fig 2. The sloping line corresponds to the conductivity of solid solutions of silver in copper, and the horizontal offshoots correspond to the conductivity of the two-phase alloys in equilibrium at the two temperatures shown. The electrical conductivities are very high, even for the 750°C anneal. The potentiality for age hardening from supersaturated alpha copper solutions appears to be excellent from the solubility line, but Smith and Lindlief6 have shown that the response to age hardening of solution-annealed alpha alloys is not good. They found that the tensile strength of a 5 pct Ag alloy aged at various temperatures was not as great as in the quenched condition, even though, anomalously, the hardness increased from RB68 to RB78 by annealing for 4 hr at 400°C after a 750°C quench. Weist7 also found that the alloys increased in hardness

Jan 1, 1948

By J. D. T. Steyl

Anglo American Corporation and the University of British Columbia have developed a medium-temperature oxygen pressure leaching process for the extraction of copper from chalcopyrite concentrates in an acid-sulphate system (AAC/UBC process). Leaching is performed at 150°C and surfactants are added to disperse molten elemental sulphur from the unreacted sulphide surface to prevent liquid sulphur occlusion. Copper extractions of over 95% and elemental sulphur yields of around 60% were observed over a 2-hour average residence time in a continuous pilot autoclave. Sporadic blockages occurring under continuous conditions were found to be caused by the accumulation of molten elemental sulphur mixed with unreacted sulphide mineral. A batch programme of experimentation was undertaken to establish the reason for this phenomenon. Batch experiments were conducted at low pulp densities on concentrate samples with narrow size distributions and at similar solution compositions to those experienced in the pilot autoclave. The overall rate of chalcopyrite oxidation was shown, under approximately constant solution composition, to be a strong function of the total available mineral surface area. Initial copper extraction rates followed the shrinking particle kinetic model under intrinsic surface control. Deviation from shrinking particle kinetics was however observed after a certain oxidation time. Secondary electron images identified small (typically less than 20 µm) sulphur conglomerates at the point of deviation, which 'collected' unreacted chalcopyrite mineral particles and lowered the total mineral surface area available for oxidation. These sulphur clusters are thought to be the precursor for blockages experienced in the continuous pilot autoclave. These results emphasised the importance of fine grinding (P80 5-20 µm) and suggest that shorter residence times may minimise the formation of sulphur conglomerates in a continuous autoclave operating at medium temperature.

Jan 1, 2004

By S. P. Kinney, A. C. Fieldner, S. H. Katz

"The regrettable death of James S. Cunningham, Foreman Miner, attached to Bureau of Mines Rescue Car No. 2, while wearing a half-hour type oxygen breathing apparatus in a gasoline storage tank at Trinidad, Colorado, raised the question as to the possibility of gasoline vapors permeating the rubberized fabric of the breathing bags of such apparatus.It is known that most gases and especially certain organic vapors permeate rubber, by solution or a similar process. The rubber becomes saturated with the gas and if a concentration of gas is maintained on one side of the rubber sheet it slowly gives off gas from the other side. It of course takes some time for the gas to diffuse through the rubber and the length of time before it reaches the other side is proportional to the thickness of the rubber. The amount of gas that passes through per unit of area in unit time increases with the concentration of gas and also varies with the structure and composition of the rubber.It has been suggested that the gasoline vapor could not have penetrated into the interior of an oxygen breathing bag because the pressure is greater on the inside, but this is not true as the process of permeation by solution in the rub¬ber is affected only by the difference in the partial pressures of gasoline vapor on the inside and outside of the bag. The positive oxygen pressure on the inside can only prevent the entrance of gasoline vapor through measurable holes, and has no effect on permeation by diffusion through the rubber.A sample of gasoline was obtained from the tank in which Cunningham met his death. Examination by Dr. E. W. Dean of the Petroleum Division of the Bureau of Mines gave the following results.This shows the gasoline to be heavy and typical of the gasolines sold throughout Colorado for motor fuel A. Salvus half hour oxygen apparatus was arranged with the breathing bag only in a gas tight box in which the space was kept saturated with the vapor of this gasoline. The main part of the apparatus was outside the box. Oxygen from the apparatus was breathed by a man in the usual manner. Gas samples were taken from the box at intervals to determine the concentration of gasoline vapor, also samples of the oxygen breathed were taken from a side tube in the mouthpiece. The room temperature was 75°F. The concentration of gasoline vapor in the box at the beginning of the test was 4.3%. The man breathing from the apparatus thought he detected gasoline in his oxygen in two minutes after starting the test. Analysis of the inspired oxygen at this time showed 0.03% gasoline vapor. The same man remained on the apparatus for 18 1/2 minutes without suffering any ill effects. His place vas then taken by another man who wore the apparatus until the oxygen was exhausted without noticing more than a trace of gasoline at any time. At the end of the test the inspired oxygen contained 0.07% gasoline vapor. The total time of test was 38 minutes."

Dec 1, 1919

By A. W. Cochardt

THERE are a number of effects that can cause material damping or internal friction. Some of these are frequency dependent, such as the thermo-elastic effect' and the stress-induced ordering.' Others depend on the amplitude of vibration, i.e., the damping related to the motion of dislocations3 and that due to magneto-mechanical hysteresis.' While many of these effects have been studied, only the magneto-mechanical effect has found extensive practical application. It is the principal source of damping in the current blade material in steam turbines.A magneto-mechanical hysteresis loop is seen in Fig. 1. If an unmagnetized, polycrystalline wire of a material exhibiting magneto-mechanical hysteresis, such as an Fe-14 pct A1 alloy, is twisted in torsion, a relation between shear stress and shear strain y is observed as indicated. The stress-strain curve does not follow Hooke's law -dashed line. Instead, the strain y increases nonlinearly and partly irreversibly, due to the motion of ferromagnetic domain walls,* until a critical stress is reached, which in this case is about 3,500 psi. If the applied stress is raised further, the strain appears to increase linearly and reversibly in accordance with Hooke's law, since all domains are now aligned in easy directions of magnetization nearest to the direction of the applied stress, and plastic flow has not yet started noticeably. On removing the applied stress, a remanent shear strain y, is observed, which is related to the irreversible magnetostriction of the material.' The energy dissipated in the material during a stress-strain cycle is proportional to the critical stress t, and the remanent magnetostrictive shear strain 7,. The purpose of this investigation was to make a survey of the magneto-mechanical damping of ferro-

Jan 1, 1957

High-sulphidation (HS) gold, silver and/or copper deposits are generated in both the epithermal and the upper parts of the underlying porphyry environments over vertical intervals of up to 2 km. The HS deposits are generated in advanced argillic lithocaps, which are products of the absorption of acidic magmatic volatiles by voluminous groundwater systems. Mineralisation styles in HS systems reflect depth of formation as well as the interplay between structural, lithological and hydrothermal parameters. The deep parts of HS systems, at depths of >1000 m, are typified by disseminated copper¦gold mineralisation comprising digenite, chalcocite and covellite in pervasive advanced argillic as well as underlying sericitic alteration. In highly telescoped systems, such mineralisation may overprint porphyry stocks and associated quartz-veinlet stockworks. Intermediate levels of HS systems commonly contain fault-controlled copper-gold mineralisation, typically as enargite in bodies of vuggy residual quartz, silicification and/or massive pyritic sulphide. The shallow parts of HS systems, at depths of The exploration focus is on four principal HS mineralisation styles:copper (eg Chuquicamata, Monywa) or copper-gold (Wafi) in the deep porphyry-hosted parts of systems preferably, in the case of the latter, where supergene oxidation is limited and, hence, flotation may be used for metal recovery; copper¦gold-bearing replacement mantos and pipes hosted by carbonate wallrocks in the deep parts of systems (eg Bisbee); high-grade gold in late-stage veins or hydrothermal breccias that overprint the intermediate to shallow levels of systems (eg El Indio, Goldfield); and large, bulk-mineable gold deposits in the shallow parts of systems that were subjected to supergene oxidation, thereby permitting heap-leach treatment (eg Yanacocha, Pierina). To these preferred HS styles may be added the low-sulphidation vein or disseminated gold¦silver mineralisation that is commonplace alongside many HS systems (eg Victoria at Lepanto).

Jan 1, 1999

By M. L. Glenn

The Bureau of Mines is conducting research on Fe-based alloys using Si and Al additions to reduce the Cr required for heat-resisting appli-cations. Part of this research is being done to evaluate alloys containing (8-10)Cr-(10-14)Ni-(0-8.5)Si-(0-4) Al to determine which of these alloys have austenitic structures, as well as fabrication properties and oxidation resistance sufficient to substitute for type 304 stainless steel. Based on initial results, an Fe-lOCr-11Ni-5Si alloy and an Fe-8Cr-13Ni-5Si alloy were selected for evaluation of oxidati.on, stress rupture, and tensile properties. Both alloys have oxidation resistance at 7000 and 8000 C that is better than that of type 304 stainless steel. The stress rupture strengths are less than that of type 304 stainless steel but significantly better than that of commercial heat-resisting steels with similar Cr contents. Yield strengths of the alloys were equivalent to that of type 304. Both alloys had high tensile strengths comparable to those of stainless steels that transform to martensite during straining (e.g., type 301). These alloys have weld-hot-cracking resistance comparable to that of type 304 stainless steel. This initial study shows that Si has potential as a substitute for Cr in stainless steels for heat-resisting applications.

Jan 1, 1984

By A. L. Irwin

THE problem of compensation for labour is probably the oldest and most complicated one in history. The wage that a man receives is possibly the most concrete thing he gets out of his job and, rightly or wrongly, is generally considered by him to be the most important item in connection with his daily work. How today workers in an equitable way has been the study of industrialists for many years, and a great number of ideas have been tried out in an effort to arrive at a reasonable solution of the question. The idea of establishing a measuring stick for various types of work has intrigued industrial management for a long time and, after considerable study, the principle of Job Evaluation has taken form unti1, at the present time, it is becoming increasingly useful to industry at large. Job evaluation is a plan which is used to determine the relative worth of occupations by means of arbitrary measuring scales. These scales are developed for individual industries and are generally 'tailor made' for each particular case. There are as yet no absolute methods of measuring the work done by human beings and, as a result, one has to depend on comparative values to arrive at conclusions. However, job evaluation has provided us with a basis of negotiation for wage rates which is more satisfactory than mere guess work or persona! opinion. It supplies a common ground for discussion which is understandable by all taking part and ensures that thinking with regard to wage setting is carried out along standard lines.

Jan 1, 1943

By M. Piard

The scarcity of literature referring to mines in the Rockies has compelled the writer to co-ordinate information and advice taken at the very source. Help was gladly given by active inspectors and mine bosses. Although the field is unimportant at the present time, due to its distance from markets for raw coal, it is quite worthy of the attention it is receiving from two continents; for, with the commercial synthesis of liquid fuels, it would become the largest fuel laboratory in the world, provided, of course, that freight cost drops to a low comparative level. As explained below, there are no obstacles to economical and safe operation under anything like the typical outcrop shown in Figure 1. Although coal dust is probably more dangerous in the Rockies than anywhere else, the damp outcrops afford means of control. The abundant gas may be bled to the open air, and the rigid roof will settle gradually under a wide span of opened outcropping. The Panel Retreating Wall The Measures: Coal measures having an attitude similar to that shown in cross-section in Figure x are characteristic of the active coalfield on the Alberta side of the Rockies, and they are also found on large tracts of undeveloped land west of the divide. The small anticlines, not shown in the cross-section, do not affect the progress of a pillar line, provided their crests are connected to the atmosphere by drainage bore-holes.

Jan 1, 1928

"Located in Madison River Canyon, about 14 miles by road from Norris, Mont. Built in 1907 by Madison River Power Co.DAM: Rock filled wooden crib structure, 183 ft. long, 34 ft. high or 44 ft. to top of flashboards.SPILLWAY: 140 ft. long, equipped with flashboards 10 ft. high.PIPE: One 10-foot and one 12-foot wood-stave pipe, 7,515 feet long.PRESSURE: One pressure chamber, 32 ft. high, 30 ft. wide and 81 ft.CHAMBER: long, built of concrete.PENSTOCKS: 4 9-foot steel penstocks about 200 ft. long, one for each wheel.WATER WHEELS: 4 double horizontal, center discharge, Sampson special 44-inch turbines, 3,600 h-p., at 100 ft. head. Speed 300 r. p. m„ direct connected to generators.GENERATORS: 4 G. E., W. C., 2,250 k-w., 4,000 volts, 300 r. p. m., 3 phase, 60 cycles, alternators, with exciters mounted on same shaft.TRANSFORMERS: 12 G. E., W. C., 900 k-w., 60 cycles. High tension voltage 23,100, 34,650, 46,200; low tension voltage 4,000, 3,800, 3,600. Now operating at 46,200, delta connected. They can be connected Y for 40,000, 60,000 or 80,000.OPERATION: This is the principal plant of the whole system and carries most of the load."

Jan 1, 1913

By J. B. Boniwell

The INPUT electromagnetic prospecting system was originally developed by Dr. A. R. Barringer in an effort to increase the sensitivity and penetration of airborne EM methods. Although brought to an operational state some several years ago, it is only through relatively re-cent modifications and testing that some of the potential of the system has been fully realised. This is brought into perspective by some recent results over known ore deposits and geologic environments.

Jan 1, 1967

By D. Lansburg

Electronic detonators are increasingly being used in today’s blasting in quarries, seismic, surface and underground mines. Electronic detonators offer several distinctive features over electric and non-el (shock tube) detonators including better timing accuracy resulting in excellent fragmentation and vibration control, field programmability and digital safety means. Because of the prerequisite electrical communications between the electronic detonators and the blasting machine, the layout or hook-up of these detonators can play an important role in obtaining the communication fidelity.

Jan 1, 2011

Drilling at Ipswich during the last twelve years by the Queensland Department of Mines has proved large quantities of reserves which have assured the security of the field for many years to come. This is perhaps the greatest contribution to the development of the field since its discovery in 1827.The drilling campaign commenced in 1950 and by the end of 1961 comprised 242 holes totalling 180,220 ft.Intersections of formations and seams, accompanied by detailed surface mapping, led to more precise knowledge of the geology of the field than was previously possible, and clarified many problems of correlation. Productive formations are part of the Middle Triassic Ipswich Coal Measures, a 4,300 ft sequence of fresh-water sediments with some interbedded volcanics. They are overlain by the Upper Triassic Bundamba Group and the Lower Tertiary Booval Group.Reserves disclosed by drilling amount to 171,487,000 tons, comprising 109,407,000 tons "measured" and 62,080,000 tons "indicated". The security of these reserves encouraged many collieries to instal modern efficient mining machinery and washing plants.The climax of recent development of the resources of the field will be the commissioning in 1966 of a £33 million 360 MW power station in the Swanbank district which will consume 14 million tons of coal during its 30 year life and will have a peak demand of some 20,000 tons per week.Drilling is continuing and is expected to prove additional reserves which will justify further development of the field.INTRODUCTIONUntil 1949 there had been no concerted effort to test systematically the resources of the whole Ipswich field. Fifty two known holes totalling 30,500 ft had been drilled, eight of them by the Department of Mines, but because of poor core recovery and inadequate records most of them were of little use in a comprehensive assessment.Development of the field was being retarded by uncertainty regarding reserves and by the general state of the coal mining industry. Numbers of comparatively small independent companies and owner groups were operating coal...

Jan 1, 1963

By Elisa Alonso

Manufacturing firms that rely on finite resources have a stake in ensuring sustainable materials use. Higher material prices and uncertain material supply, consequences associated with scarcity, can be damaging to firms. Firms have a number of options to improve material sustainability including dematerialization, material substitution and recycling. However, these options require technological capability, capital investments and supply-chain infrastructure; firms may decide to make such investments only if material prices increase. Once decisions are made, the barriers and delays to implementing changes may harm firms. The impact of not reacting to changes in material supply on firms was examined for the case of different platinum-using industries. It was found that taking action is particularly important for firms when limited material availability leads to volatile market conditions. Industries can benefit especially if they ensure process flexibility and have options for changing their material use patterns.

Jan 1, 2010

By Jamie Deuel

The a ad on Connection" For the purpose of this paper, we will concentrate on the ubquitous radon gas as the principle, low-level radiation effect from uranium tailings piles. Standards are also proposed for gamma radiations but, by most accounts, this is much less of a low level problem than is radon. I am also aware of some just completed research at Oak Ridge National Laboratories that suggest polonium may be a major concern in tailings, but those data are preliminary at this time. What is radon gas? In the first place it is not a gas in the accepted sense in that it has no driving pressure head. It might prove a more convenient description to call it radon vapor. Radon vapor, then, is 7-1/2 times heavier than air. Radiologically, it is an alpha emitter which means it spontaneously gives off high ionizing potential but low penetrating power particles. In fact, the alpha particle has such low penetrating power that this sheet of paper will completely shield a person. The problem, though, is breathing the radon decay products, called radon daughters. If radon daughter products are ingested into the lungs, their alpha emissions may cause cancer. The principle carcinoma associated with breathing radon, or more basically, associated with radiological effects is oat cell car- cinoma of the undifferentiated mall cell type. Radon has a 3.8 day half life which means in less than four days half of its initial radioactivity has decayed away. In less than a month it essentially becomes inert or non-radioactive. The Tailings Situation The NRC, in its April 1979 Generic Environmental Impact Statement

Jan 1, 1983

By M Reza Afshar

In this work a mathematical model was developed to study the effect of electromagnetic force on the magnesium melt containing nonmetallic inclusion in an electrical isolated channel. The electromagnetic force exerted on the inclusion induced by DC current field was calculated. A three dimensional turbulent flow equations were solved numerically to compute the velocity field within the channel. On the basis of computed velocity and magnetic fields, the trajectories of inclusions were calculated using the equations of motion for inclusions. Parametric studies were carried out to evaluate the effect of various parameters such as current density, channel diameter and particle density on the removal efficiency of inclusions from magnesium melts.

Jan 1, 2004

By T. M. Ruff

A prototype mucking machine designed to operate in narrow-vein stopes was developed by Foster- Miller, Inc., Waltham, MA, under contract with the U.S. Bureau of Mines. The machine, called a compact loader-trammer, or minimucker, was designed to replace slusher muckers in narrow-vein underground mines. The minimucker is a six-wheel-drive, skid-steered, load-haul-dump (LHD) machine that loads muck at the front with a novel slide-bucket system and ejects it out the rear so that the machine does not have to be turned around. To correct deficiencies of the tether-remote-control system, a computer-based, radio-remote-control system was retrofitted to the minimucker. Initial tests indicated a need to assist the operator in guiding the machine in narrow stopes. An automatic guidance system that used ultrasonic ranging sensors and a wall-following algorithm was installed. Additional tests in a simulated test stope showed that these changes improved the operation of the minimucker. The design and functions of the minimucker and its computer-based, remote-control system are reviewed, and an ultrasonic-sensor-based guidance system is described.

Jan 1, 1992

By E. G. King

This report contains experimentally determined heat-content values for cerium dioxide and Columbium (niobium) dioxide in the temperature range from 298° to 1,800° K. There are no previous similar data for Columbium dioxide, and those for cerium dioxide have an upper limit of 373° K. The heat-content and corresponding entropy-increment data are presented in tabular form. Equations were derived to represent the heat contents and heat capacities. The data for cerium dioxide are entirely regular, but those for columbium dioxide show two previously unreported anomalies at 1,090° and 1,200° K.

Jan 1, 1961

By Frank G. Snyder, Paul E. Gerdemann

The Southeast Missouri lead district, located about 70 miles south of St. Louis, embraces four important sub-districts and several minor ones. The important sub-districts, in order of discovery, are Mine La Motte, the Old Lead Belt, Indian Creek, and the Viburnum Lead Belt. Descriptions that follow are of geology and ore deposits of the Old Lead Belt. The ore deposits are stratiform in character and are localized in a narrow carbonate bar and algal reef environment on the flanks of exposed Precambrian of the St. Francois Mountains. Ore structures include a variety of primary depositional features such as pinchout zones, disconformities, ridge structures, reefs, and submarine gravity slides. Faulting, prior to and during ore deposition, "prepared" the host rock and strongly fractured areas are mineralized much more intensively and extensively than unfractured parts of the same sedimentary structures. The deposits are epigenetic in character. Mineralization is believed to have occurred at the time that post-lower Ordovician faulting took place. The mineralizing solutions are believed to be concentrated brines from adjacent basins that moved out of the basins during faulting, uplift, and erosion of the St. Francois positive area.

Jan 1, 1968

By William J. Campbell

The purpose of this investigation was to develop a rapid, accurate method of analysis for small amounts of calcium in wolframite concentrates. This analysis is necessary to determine if the wolframite concentrates meet United States National Stockpile Specification P-57R2, which limits the calcium content to 0.2 percent. Because of the small depth of the sample analyzed in fluorescent X-ray spectrography, the calcium Kaline intensity was a function of the chemical composition of the calcium-bearing particle as well as the total matrix composition. This particle-composition effect was particularly important in this analysis, as the calcium may be present as a carbonate, tungstate, phosphate, etc. Three methods of preparing the sample eliminated the variation of calcium Ka intensity with mineralogical occurrence: (1) Reduction in particle size by extensive grinding, (2) chemical fusion with sodium carbonate, and (3) solution of the calcium by an acid attack.

Jan 1, 1958

By R. F. Evans, J. M. Avery

MUCH has been written of the glamour of magnesium from sea water, the Aladdin-like creation of a huge magnesium plant in the Nevada desert using cheap hydroelectric power from Boulder Dam; the marvels of the Hansgirg process for the electrothermal reduction of magnesium oxide by carbon, and the ferrosilicon process for producing magnesium from dolomite. This is the story of the production of -magnesium by the electrolytic process, using steam-electric power supplied by a public utility, in a plant at Painesville, Ohio, 30 miles east of Cleveland on the shore 'of Lake Erie. The story is not without interest, since it involves several unique developments that provide the answer to a question frequently asked: How is it possible to produce magnesium metal economically at such a location as Painesville, Ohio? Basically, the answer lies in making use of facilities already in existence for the production of soda ash, which makes it possible to manufacture magnesium chloride, the principal raw material, cheaply enough to offset the high cost of electric power. To this is coupled the successful conversion of by-product chlorine into a product required for the war program. The source of magnesium for this operation is the enormous surface deposit of high-grade dolomite in the region south of Toledo, within reasonable freight haul of Painesville. This same geological stratum underlies the Painesville plant, but unfortunately at a depth of about 3000 ft. apparently too great a depth to permit underground mining to compete with the delivered cost of rock from surface quarries in other areas. The cost of dolomite obviously is an important factor, since the rock contains only some 12 per cent magnesium (20 per cent MgO) so that one dollar on the cost of stone means more than $8 in terms of its magnesium content, and more than that in terms of recoverable magnesium metal. PRODUCTION OF MAGNESIA FROM DOLOMITE In the summer of 1941, the Diamond Alkali Co. was well along with construction of a plant intended for the commercial production of refractory and other grades of magnesia from dolomite. The process to be used was designed to make maximum economic advantage of existing plant and operations by tying the production of magnesia in with the manufacture of soda ash in such a way as to make use of the lime (CaO) value of calcined dolomite. The process finally adopted after a lengthy research and development program has much in common with the old Clerc-Nihoul process, but includes certain innovations found to be necessary or

Jan 1, 1945