Search Documents

By R. M. G. Machunter

The presence of ultra-fine particles affects the separation performance of wet gravity separation equipment. Several studies have been undertaken to establish the maximum level of these particulates that can be tolerated by spiral separators and it has been found that unless the ultra-fine material is effectively processed, relatively low proportions in the ROM material combined with high feed rates can result in degradation in plant performance and/or excessive water consumption. The maximum level of particulate material in the process water has been determined by examination of separation performance of spiral separators under varying slime loading. This work has been conducted utilizing various feed sources and a robust ‘rule-of-thumb’ has been derived.

Jan 1, 2005

By A Thornton, D Engelhardt, J Woodg

Grinding is a critical part of nearly all mineral processing operations. It is the largest consumer of energy on the mine site (and thus indirectly a producer of greenhouse gas through the generation of electrical energy at the power station). Since comminution is one of the main consumers of electrical energy worldwide, efficient control of grinding mills is of paramount importance. Mill Auto-Pilot is a control system developed for SAG mills to stabilise load and power and improve the efficiency of control and increase throughput. A dynamic, mechanistic model of the grinding circuit is used to determine circuit parameters which can not normally be measured using conventional instrumentation. The circuit model is built from models of the unit operations (such as conveyors, SAG mills, cyclones, sumps, etc), and so captures the dynamic complexities and interactions of real circuit operation. CSA Mines at Cobar NSW accepted an offer to be the reference site for Mill Auto-Pilot and the system was installed in March 2004. In this application the model is used to predict mill load mass, mill solids residence time and cyclone underflow density. These parameters are used to control mill load, power and mill discharge density. The outcomes of the introduction of Mill Auto-Pilot at the CSA Mine are discussed.

Jan 1, 2004

By H. C. Miller

The success of any project in which gas is injected into oil-producing sands to increase the current rate or the economic ultimate production of oil or in which surplus gas from oil producing operations is stored temporarily in reservoir sands that have been wholly or partly depleted of their producible oil depends mainly upon an understanding of the underground movements of oil, water, and injected gas and the ability to control their speed and direction of migration through the reservoir sands. Many operators believe that injected gas always travels up the structure and drives oil to wells structurally higher than the injection wells, because the specific gravity of the injected gas is less than that of the fluid substances in the formation. Consequently, many injection wells are located on the flanks of oil-bearing structures with the idea of utilizing the energy of the injected gas to drive the oil to producing wells higher on the structure. It is true, under certain conditions of pressure and fluid depletion of the reservoir sands, that injected gas will move in an up-structure direction, but the theory that injected gas always moves up the structure is based on an erroneous conception of the laws that pertain to the expansion of gases. By definition, "a gas is distinguished by its property of infinite expansion and is limited in volume only by the walls of the vessel which contains it."3 The expansion of gas that is injected into reservoir sands also is limited by "walls" that surround the space influenced by the injected gas. The walls of the majority of undrilled or virgin oil-bearing reservoirs in California are the impervious shales overlying and underlying the productive strata and the "dams" or effective barriers of edge water around the rims of the reservoirs. When gas is injected into the sands of a producing reservoir, regardless of the location of the injection well on the structure or the degree of depletion of oil from the sands, one of the walls which confine the gas in the structure about the injection well is fluid. This wall will be edge water in a nearly depleted reservoir, where the drainage cones or regions of reduced pressure about injection and producing wells intersect; and, where there is no interference of drainage cones and the injection well is structurally above the edge water, the wall will be oil. In some producing reservoirs bottom water may be the lower wall of the space that confines the gas about injection wells, but the effect of bottom water on limiting the expansion of gas is the same as if the water was not present and impervious formation separated the producing from the underlying nonproducing strata. Therefore, since compressed gas always seeks regions of reduced pressure and its final volume is limited only by formation and fluid barriers and since the force exerted by the gas under pressure is equal in all directions, the course of migration of injected gas in reservoir sands in California and the

Jan 1, 1932

By S. Dixon

The Peñasquito deposit in Mexico is one of the largest grassroots precious metal discoveries developed in recent years. Goldcorp Inc. acquired the gold-silver-lead-zinc property with the acquisition of Glamis in 2006. The Peñasquito property is located in the northeast corner of Zacatecas state, Mexico. The elevation of the property averages 1,900 m (6,200 ft) above sea level. It is situated in a wide east-west valley. Minera Peñasquito, S.A. de C.V., wholly owned subsidiary of Goldcorp Inc. has operated twin SABC-flotation lines since June 2010. Each line is capable of processing 50,000 tonne per day using a SABC grinding circuit followed by flotation to produce lead and zinc concentrates. The addition of a Polysius Polycom HPGR 2417 with dual 3,000 kW drives to reduce the crushed pebbles produced by the SAG mills was planned to increase production to 65,000 tonne per day per line. The production has been limited to 100,000 tpd due to operating issues in the grinding circuit. The operating issue has been the amount of pebbles generated by the SAG mills is significantly less than originally planned. This paper describes the planned installation of a crushed augmented feed to maximize utilization of the HPGR capacity. This coupled with full utilization of the SAG and Ball Mill available energies there is the potential to achieve a 50% total capacity increase from the grinding circuit.

Jan 1, 2012

By A. R. Farkoosh, K. Korgiopoulos, McGill University, O. Rodop, L. A. Villegas Armenta

"New generation of Al-Mg-Si alloys with thermally stable dispersoids that prevent recrystallization and grain growth during hot deformation are currently used in automotive components requiring good formability. Alloy chemistry controls the phase formation especially age-hardening precipitates, dispersoids, and primary intermetallic which have pronounced effect on grain structure, strength and formability. In this work, thermodynamic calculations have been used to predict the effects of varying levels of Si (0.5-1.5wt%), Mg (0.5-1.5wt%) and Mn (0.1-2.5wt%) on phase selection. Thermodynamic calculations have been performed in equilibrium and non-equilibrium conditions via the FactSage™ software using the FTlite database. Selected compositions have been cast, heat treated, extruded and characterized through scanning electron microscopy with energy dispersive spectroscopy and electron channeling contrast imaging techniques. The calculations showed that at the hot deformation temperature of ~540 oC, exceeding certain Mg and Si levels would lead to retained *-Mg2Si intermetallics and Si particles at the grain boundaries in addition to a-Al-(Mn,Fe)-Si. It was found that retained *-Mg2Si phase which adversely affects formability can be avoided for Si+2Mg levels lower than 2.3wt%. FactSage calculations also showed that increasing Mn from 0.5wt% to 1wt% leads to an increase in the amount of dispersoids (from 1wt% to 2wt%) that can potentially slow down recrystallization and grain growth during hot deformation and improve formability. Calculations at room temperature also show that for an alloy with 0.7wt% Mg, excess Si beyond 0.7 wt% promotes the precipitation of Si clusters in the Al matrix that accelerate natural age-hardening. Results were confirmed by experimental investigation.INTRODUCTIONAluminum alloy 6082 (Al-Mg-Si) is used in the automotive industry because of its high strength, and good weldability (I. J. Polmear, 2006). The alloy is age-hardenable through the precipitation of ß-Mg2Si and its precursors, and the recrystallization is usually inhibited by Mn- and Cr-containing dispersoids formed through high temperature heat treatments (I. Polmear & Couper, 1988). However, it is known that minor changes in alloy chemistry (Mg/Si ratio) can have significant influences on the ductility and formability of these alloys by altering phase selection and the resultant microstructure (Gupta, Lloyd, & Court, 2001; McQueen & Celliers, 1997; Zajac, Hutchinson, Johansson, & Gullman, 1994). For automotive applications where wrought alloys (usually extrusions) are cold-formed to produce suspension components, the chemistry of the alloys and the extruded structure are of crucial importance as they determine the formability at room temperature (Asensio-Lozano, Suárez-Peña, & Vander Voort, 2014). In this study, thermodynamic calculations along with experimental investigations were carried out on the Al-Mg-Si system to understand their phase formation and precipitation hardening as a function of alloy composition."

Jan 1, 2016

By J. Koster

In the western United States occurs deposits of low-grade chromite which, when concentrated, may be reduced to ferrochromiun in electric furnaces that derive energy from dams and hydro plants now in course of construction. Montana ore was chosen for the experiments. A 1-ton sample contained 26 percent Cr203, 17 percent Fed, and 17 percent SiO2, plus other constituents, and the concentrates therefrom assayed 44 -percent Cr203, 23 percent FeO, and 0.79 per cent SiO2, Gravity concentration was found to be the best method. Ferrochromiums are of two grades - high-carbon with 66 to 70 percent chromium and 4-112 to 6 percent carbon and low-carbor with 67 to 72 percent chromium and 0.6 to 2 percent carbon. Both are made in electric furnaces that use anthracite as a reducer and suit-able fluxes. The concentrates mentioned mere smelted under different conditions, and it was concluded that domestic ore could be reduced with anthracite to produce a ferrochromium of S to 10 percent carbon content at yields of 90 percent without retreating the slag. This carbon may be lowered to required proportion with calcium and silicon, but the former requires a great excess and the latter leaves an alloy high in silicon. INTRODUCTION Chromite occurs in several regions of the United States, but the known deposits of this mineral have not been large enough or high grade enough to permit them to compete under normal conditions with imported ores. There are numerous deposits of chrome ore along the West coast. These are generally conceded to be relatively small, although some -were worked during the World War. There are some indications of a revival of interest in California chromites. Montana contains large chromite deposits in Stillwater and Sweetgrass Counties. The utilization of chromite for ferrochromium and. the manufacture of stainless steels is distinctly an electrometallurgical problem; consequently, a study of methods for treatment of chromite might pave the way for the establishment of new electrometallurgical industries in the Western States. This thought is supported by the cheap power that is soon to become available from the western dams. Farther, submarginal domestic chrome deposits might thus be turned into profitable producers.

Jan 1, 1936

By S. F. Emmons

The first paper which appears in the published Transactions of our Institute is that read by our respected Secretary at its first meeting in Wilkes-Barre in May, 1871. It is entitled " The Geographical Distribution of Mining Districts in the United States," and presents a brief but masterly review of what was known of the distribution of our deposits of useful minerals, particularly the metals, not only from a geographical but from a geological stand-point. At the request of Dr. Raymond I agreed, somewhat hastily, perhaps, to write for this occasion a brief sketch of the geological distribution of the deposits of the useful metals in this country, in the light of the increased knowledge of the present day. In the time given no personal investigation was possible, and as it was therefore out of the question to attempt to make anything that could be considered an original contribution to the history of our ore-deposits, I have been obliged to limit myself to an examination of such pub-

Jan 1, 1894

By J. Koster

In the western United States occurs deposits of low-grade chromite which, when concentrated, may be reduced to ferrochromiun in electric furnaces that derive energy from dams and hydro plants now in course of construction. Montana ore was chosen for the experiments. A 1-ton sample contained 26 percent Cr203, 17 percent Fed, and 17 percent SiO2, plus other constituents, and the concentrates therefrom assayed 44 -percent Cr203, 23 percent FeO, and 0,79 per cent SiO2, Gravity concentration was found to be the best method. Ferrochromiums are of two grades - high-carbon with 66 to 70 percent chromium and 4-112 to 6 percent carbon and low-carbor with 67 to 72 percent chromium and 0.6 to 2 percent carbon. Both are made in electric furnaces that use anthracite as a reducer and suit-able fluxes. The concentrates mentioned mere smelted under different conditions, and it was concluded that domestic ore could be reduced with anthracite to produce a ferrochromium of S to 10 percent carbon content at yields of 90 percent without re-treating the slag. This carbon may be lowered to required proportion with calcium and silicon, but the former requires a great excess and the latter leaves an alloy high in silicon. INTRODUCTION Chromite occurs in several regions of the United States, but the known deposits of this mineral have not been large enough or high grade enough to permit them to compete under normal conditions with imported ores. There are numerous deposits of chrome ore along the West coast. These are generally conceded to be relatively small, although some were worked during the World War. There are some indications of a revival of interest in California chromites. Montana contains large chromite deposits in Stillwater and Sweetgrass Counties. The utilization of chromite for ferrochromium and. the manufacture of stainless steels is distinctly an electrometallurgical problem; consequently, a study of methods for treatment of chromite might pave the way for the establishment of new electrometallurgical industries in the Western States. This thought is supported by the cheap power that is soon to become available from the western dams, Farther, submarginal domestic chrome deposits might thus be turned into profitable producers.

Jan 1, 1936

By Hillary W. St. Clair

The reduction zone of the iron blast furnace is represented by a mathematical model of the chemical reactions and heat transfer that occurs between gas and solids during the deoxidation of iron oxide. The model consists of a set of equations and an algorithm whereby the equations may be solved to give the temperature and composition of gas and solids at any position in the reaction zone and at any time after a specified initial state. The model is applied to the special case in which ferric oxide is reduced by graphitic carbon and carbon monoxide produced by burning carbon in dry air. The rate of reduction, carbon consumption and maximum temperature are shown as functions of the temperature and rate of flow of the incoming reducing gas and external heat loss. The model of the reduction zone is the essential part of a general mathematical model for simulation of the iron blast furnace. The simulation model will serve as a research tool to be used in conjunction with an experimental or operating furnace. After the simulation model has been correlated with the real furnace, it is proposed that further experimentation be done mostly with the model. The real furnace will then be operated primarily to test and confirm the model.

Jan 1, 1967

By Joseph L. Gillson

In this volume, which is divided into chapters on a commodity basis, many subjects inevitably have a common interest with others, or are interrelated in one way or another. No group of commodities is so outstanding in this regard as is that group of which the basic raw material is a carbonate rock. There are chapters in this book on dimension stone, on crushed stone, on chalk and whiting, on cement, on lime, on magnesite, on sodium carbonate; all of which are entirely, or partly, products of the "carbonate rocks." Rhodochrosite, witherite and strontianite are other carbonates described respectively in chapters on manganese minerals, barium minerals and strontium minerals; and travertine and cave onyx are carbonate materials used as ornamental stones. High grade marble is used for monuments and statues and as a decorative building stone. The aggregate tonnage of the basic raw material, the carbonate rock, is so enormous that it exceeds the tonnage of any metallic ore mined and quarried in the United States, and in turn is exceeded only by coal, sand and gravel, and by water in the gross tonnage produced by the mineral industry in this country. The specialties, including magnesite, sodium carbonate, and rhodochrosite, witherite and strontianite are produced from uncommon rock types of limited occurrence. They are described adequately in the chapters devoted to these subjects. This chapter is concerned with the limestones and dolomites. No other solid rocks are as important as these in the industrial life of the world, nor are any so widely known. Massive units of some carbonate formations form many of the spectacular features of some of the most rugged mountains in the world, such as the Dolomite Alps, the Canadian Rockies, some rugged peaks of the eastern flanks of the American Rockies in Colorado, Wyoming and New Mexico and in many ranges in Utah, Nevada and Arizona. These continue down the Sierra Oriental in Mexico and on around the world to the flanks of the Himalayas, in the South China Highlands, and separating Asia and Europe in the flanks of the Ural Mountains where they form many reexhumed hills called Shikhany.50a Less rugged and more nearly flat-lying carbonate rocks underlie most of the area of our great Middle Western plain, the southern part of England and the northern part of Africa. These are the common rock formations known from boyhood to a large part of the world's population. The use of lime, produced by the burning of limestone, goes back to antiquity, and mortar was used widely in Biblical times. The cement made by mixing volcanic ash with lime was a basic material of construction when Pompeii was built. Our Eastern states are dotted with abandoned limestone quarries, and the ruins of old lime kilns which were operated in Colonial days. Many limestones and dolomites are found in flat-lying strata of a thickness convenient for quarrying as a building stone, so that houses and other structures have been built with them for centuries. In order to replace the muddy and rutted dirt roads with surfaces that could stand the hard usage of his wagons and carts, man learned to crush stone and put a layer of it on his old trails. Such roads built by the Romans have been in use over much of

Jan 1, 1960

By H Waterer, L Zheng, T Kalinowski

The Hunter Valley Coal Chain (HVCC) consists of mining companies, rail operators, rail track owners and terminal operators, together forming the worldÆs largest coal exporting facility. In 2008, the throughput of HVCC was about 92 million tonnes, or more than ten per cent of the worldÆs total trade in coal for that year. The coal export operation generates around $15 billion in annual export income for Australia. As demand has increased significantly in recent years, and is expected to increase further in the future, efficient supply chain management is crucial. The Hunter Valley Coal Chain Coordinator Limited (HVCCC) was founded to enable integrated planning and coordination of the interests of all parties, thus improving the efficiency of the system as a whole. One of the many planning challenges faced by the HVCCC is that of annual maintenance planning. Different supply chain elements, such as trains, railway track, terminal equipment and load points, must undergo regular preventive and corrective maintenance, leading to significant reductions in system capacity (up to 15 per cent). However good alignment of the maintenance tasks can reduce their impact, and the HVCCC undertakes an annual process to ensure the impact of maintenance on the supply chain capacity is as small as possible. This is achieved in an iterative negotiation process between HVCCC and individual service providers. In the past, maintenance schedule optimisation was largely manual, which for the more than 1000 tasks involved is quite labour-intensive.In this paper the authors describe an approach developed at the University of Newcastle in partnership with the HVCCC to automate this schedule optimisation process. We will discuss our experience in applying exact (mixed integer programming) and heuristic techniques from mathematics and computer science to address the problem. This work is anticipated to lead to new decision-support tools for the HVCCCÆs capacity planning team.

Sep 26, 2011

By R. Sibley, K. Perry, E. McCorkle, M. Coy

Black powder has been used in fireworks since the 10 th century in China. To this day, black powder still has a variety of uses, including fireworks, and remains relatively unchanged. Black powder is used in the firework shell to help produce the effect and in the lift charge to propel the shell skyward. The performance of fireworks shells used in displays varies greatly. In fireworks shells, there are two different black powder charges that differ in construction based on the desired performance of the shell. The two charges consist of the lift charge and the break charge. The lift charge is the first to fire and propels the shell out of the mortar. The break charge is the second to fire and is initiated after a delay from the lift charge; its purpose is to burst the shells effect over the desired area of the sky. The lift charge provides the shell with its initial velocity by pressurizing the mortar below the shell body. The pressurization process is violent and occurs in fractions of a second. The purpose of these experiments are to better understand the pressures sustained in fireworks mortars during the firing process. Mortars and shells vary by size and weight. Pressures in each mortar were monitored at various heights along the mortar to provide a pressure profile during shell lift. A high-speed camera was used to measure shell exit velocity near the mortar’s muzzle. This information was correlated with the size and weight of shells and their respective lift charges

Jan 1, 2024

By S Harvey

An inrush of water or mud into an underground mine, or sudden subsidence above mining voids represent low probability but high impact risks in underground mining. About two such incidents involving multiple fatalities or loss of production are reported each year worldwide. On average, Australia experiences one such incident every three to four years. This paper reports the development of a Standard that is intended to eliminate fatalities due to inrushes and subsidence.

Jan 1, 1998

By W. M. Bangert, F. S. Boericke

"INTRODUCTION Previous investigations of the Boulder City station of the Bureau of Mines have demonstrated that low-grade domestic chromite concentrates can be roasted with carbon to obtain selective reduction of the contained iron, and that the reduced iron can be removed by acid leaching of the roasted products to produce residues with higher chromium iron ratios. Thus, some chromite ores or concentrates that originally contain too much iron to be acceptable for the production of ferrochrome can, by this treatment, be rendered marketable as ""high-grade"" chromite. 3/The present report supplements the earlier work of the Bureau and re¬cords the results of small-scale laboratory tests investigating the effects of:1. Temperature and time of the reducing roast.2. Chromite and carbon particle size.3. Ratio of carbon to chromite in the initial roast mixture.4. Variations in the alumina and silica content of the ore.5. Back-oxidation of the roast product.6. Temperature and time of leaching .of roast product.This work differs from that done previously in that particular emphasis was placed on roast mixtures containing just enough carbon for the reduction of the iron in the chromite, whereas some two and one-half times this amount of carbon was used in the earlier work.In addition to these tests, the mechanism of the production reactions was examined for the purpose of explaining the precance of acid-soluble chromium, which occurs under certain conditions of chromite reduction."

Jul 1, 1945

By Won C. Park

Experiments showed changes in the mineral content of dolomitic oil shale at temperatures and exposure times which bracket conditions encountered during in situ retorting. Laboratory results correlate with cores from a spent in situ retort at Occidental's Logan Wash test site at Garfield County, Colorado. Dolomite, CaMg(CO3)2, decomposes rapidly to form periclase, MgO, calcite, CaCO3, and CO . Both calcite and periclase are intermediate products that can be stabilized by CO atmosphere at lower temperatures, while steam accelerates the formation 2 of silicates. The decarbonation of calcite appears to involve a direct reaction with both quartz and periclase in forming these silicates. Decarbonation preceeds the formation of akermanite, Ca2 MgSi 207, and diopside, CaMgSi 206, within several hours of heating and is followed by the nucleation of forsterite Mg2SiO4, and monticellite, CaMgSiO4. Under in situ retorting conditions, akermanite and diposide are the major minerals above 800°C. Equilibrium is not attained within 200-300 hours. In situ retorting temperatures above 800°C for extended periods of time should reduce potential ground water leaching by the formation of silicate minerals. These silicates are less soluble than free lime, magnesium or alkali oxides. There is a corresponding decrease in the natural pH of these silicates from approximately 12 down to 7.5 to 9:

Jan 1, 1981

The concept of "classification is expanded beyond the performance of the classifying equipment to include all aspects of the fines removal system of the grinding circuit. Design and operating parameters which affect fines removal are identified and discussed, and a quantitative index for circuit fines removal effectiveness is defined. This approach lends new interpretation to certain observed phenomena, and suggests useful guidelines for circuit design and operation.

Jan 1, 1985

By K Smith

This paper presents an assessment of the Robertson (2010a) method within the CPTu inversion parameter framework of Been et al. (1987), using CPTu calibration chamber data presented by Jefferies and Been (2015) and in other literature to assess the validity of the method, with particular focus on applicability of the method to TSFs (i.e. its applicability to loose silts and silty sands). The assessment demonstrates that although the method estimates values of k consistent with calibration chamber data, the method estimates values of m that are generally 1.5 to 2 times greater than calibration chamber data. As a result of this, the method generally overestimates Ψ for values of Ψ less than 0, and underestimates Ψ for values of Ψ greater than 0. This may result in both overly conservative assessment of materials as potentially liquefiable and unconservative predictions of material behaviour for loose materials.

Jul 1, 2021

By Robert F. Droullard

The Bureau of Mines has investigated techniques of using gross alpha or beta detectors to continuously measure working levels. Both methods measure radioactive particulates collected on a filter paper using a constant airflow. Inherent-error studies indicate a value of about ±3 percent for the gross alpha method and about ±8 percent for the beta method in typical mine atmospheres. However, the beta method avoids problems associated with alpha detectors and is therefore more useful. Applications of these continuous working-level detectors include work area monitoring of exposure levels in underground openings, such as mines and caves, and calibrating personal dosimeters exposed over extended time intervals.

Jan 1, 1977

By Duk-Wom Park

INTRODUCTION he most important information required for the engineering design of structures in rock is its inherent rock properties. Without providing adequate parameters on the rock property, high quality of the engineering design cannot be expected. Many laboratory rock testing methods have been developed, but they are mostly for testing intact homogeneous rock without appreciable discontinuities. In reality, the intact rock properties do not represent the behavior of rock masses because rock masses include irregularities such as joints, cracks, interlayers, variations in mineral compositjon, etc. In general the type and intensity of the rock defects may be much more important than the type of rock which will be encountered (Terzaghi, 1977; Bieniawski, 1984). In-situ rock testing can provide better information on rock parameters, but it takes a tremendous amount of effort, time and cost. In recent years, numerical modeling techniques are gaining popularity as a design tool for structures in rock bodies due to the enormous progress in computer technology (Wang, 1985; Kripakov and Melvin, 1983; Park and Ash, 1985), but it is quite dangerous to use numerical techniques without having proper input data. Bieniawski (1984) states as follows: Some design methods such as numerical techniques have outpaced our ability to provide the input data necessary for the application of these methods. In order to provide an adequate amount of input data, an extensive testing program may be required, thus major efforts in time and expenses are commonly spent, In this paper, a new rock testing method, which utilizes the principles of laser holographic interferometry, is introduced. This method requires only a few minutes to measure the modulus of elasticity and quality of a rock core sample, which does not have to be cut or ground. The Poisson's ratio can also be measured in a few minutes from a sliced rock specimen. HOLOGRAPHIC INTERFEROMETRY Principles of Holographic Interferometry In 1948, Gabor invented holography, which is the technique of reviving three dimensional images using a monochromatic light source. A full demonstration was not made then because a clean monochromatic light source was not available. Later, in the early 19601s, the laser was adopted as a monochromatic and coherent light source (Leith and Upatnieks, 1963). Since then, applications have been made in many different fields ranging from crime prevention to three dimensional television. In this technique, an image is usually recorded by means of constructing a hologram which is a record of the interference pattern formed on a high resolution photographic system as shown in Figure I. A beam splitter divides the laser beam into two beams: (1) an object beam which is expanded while passing through a beam expander and illuminates the object, and (2) a reference beam which is expanded and illuminates the holographic plate. Subsequent to an exposure, the holographic plate is developed and illuminated by the expanded reference beam. The original scene of the object is revived in a three-dimensional image. The entire instrument should be placed on a vibration free environment. The wave fields reflected by the object in two slightly different configurations can be superimposed to form an interference fringe pattern. Thus, it is possible to measure the displacement that took place between the two configurations. This method is called holographic interferometrv. There are two methods of achieving this phenomena. The first is the double exposure method, wherein two exposures of the object are made prior to developing the film. The first exposure represents the original condition and the second, the disturbed condition. The second method is the real time holographic method. In

Jan 1, 1986

By Curtis G. Kremer

"New explosives initiation systems continue to be developed as new technologies make advancements possible. Due to recent initiator developments, explosives users now have the most reliable, accurate, safest and easy to use systems ever offered. Three initiation systems recentlyintroduced which offer significant improvement over standard electric and nonelectric initiation systems include Magnadet, EXEL high-strength shock tube, and Redundant two-Dath surface delay systems. These three systems will be discussed zn cecail with rmpiasis on their functioning, safety characteristics, ani specific application areas."

Jan 1, 1991