Search Documents

By Douglas A. Sloan

AN INCENTIVE or bonus system of payment is commonly used for mine labour. The incentive rates are usually based on the variable units of production, such as dollars per foot of drift advance or cents per ton of ore broken. Portions of the work that must be done to achieve the units of ?production are independent of the production unit and tend to be fixed work for the shift or for the job, irrespective of the production achieved. This fixed work has considerable influence on the equity of incentive rates. The effect of fixed work is to accelerate the loosening or tightening of rates if the production task is over-achieved or under-achieved, and of increasing the loosening of rates loosely set and the tightening of rates tightly set. This gearing of mine contract rates is the reason why changes in conditions, materials, equipment, or methods will change the incentive earnings to a greater degree than would normally be expected. Obviously, therefore, care should be taken in the setting of the task for incentive rates as the gearing makes an inequitable rate even more inequitable.

Jan 1, 1958

By Mohammad Noaparast, Babak Fotoohi

"Due to certain advantages in (semi-)Autogenous-Ball mill circuits in most of the high-throughput ore grinding units of mineral processing plants, much attention is paid to optimize the mill performance. Despite the maturity of the grinding mill mechanical design, there had been made less attention to the efficiency of the grinding media in the past. In this research, the possibility of establishing a relationship between liner/lifter wear rate and variations in the composition of the iron ore (from Chadormalu mine) is investigated.Measurements and determination of liner/lifter wear rates and patterns concluded in recognition of critical liner segments exposed to much abrasion during the ore grinding. After metallurgical analysis of liner materials and correlation of wear rate with the ore composition, the homogeneity in the metallurgical microstructure of the alloyed steel (such as the uniform distribution and amounts of the constituent phases) was determined as the most influential factor in the response of the liner/lifter to the variations in the ore composition. Magnetite with greater abrasion index than hematite, in finer particles, is responsible for additional abrasion of liners; hematite with greater work index exists in the mill with larger particle sizes, thus it could produce wear on liner parts with less tolerance to impact as is the situation for martensitic steels.INTRODUCTIONThe mineralization in Chadormalu plutonic iron ore deposit is consisted of mostly magnetite, hematite, martite, apatite, quartz and carbonates. The average composition of the ore is presented in Table 1. In the processing circuit, the gyratory crushed ore reduced to 30 cm would finally be the feed to three similar 32’ semi-autogenous mills in parallel processing lines. The pulp in the mill would have the characteristics mentioned in Table 2. The quality of the mill output has its direct effect on the downstream processes either physically or chemically (e.g. in cycloning or flotation respectively). In order to take advantage of optimum performance for these circuits, a close control of the ore grinding conditions is necessary; because any shortages in throughput, liner/lifter damage or changes in ore composition could bring the unexpected casualties. In this work, it has been attempted to find (possibly) a reasonable relationship between variations in ore characteristics together with liner quality and the amount of wear rate in different liner/lifter segments of a semi-autigenous mill. Liner/lifter segments are supplied by three different domestic steel making companies. The alloy structure of the liners/lifters is made up of pearlitic chromoly steel."

Jan 1, 2005

By AIME AIME

AMONG the industrial motion pic¬tures released in the last year of possible interest to people in the mining industry are the following: "A New World Through Chemistry," made by the public relations department of E. I. du Pont de Nemours & Co., Wilmington, Del. This film, which is in sound and color, interprets in twenty minutes of narration and ingenious photography many of chemistry's newest developments. It may be borrowed either in 16-mm. size on an 800-ft. reel, or 35-mm. size on a 2000¬ft. reel, the only charge being the cost of returning the film. Douglas D. Rothacker, 729 Seventh Ave., New York City, is prepared to loan free of charge except for transportation each way several films prepared in the plants of the International Nickel Co., 16 mm. with sound. These include: "Nickel High Lights," 35 minutes; "Nickel Mining," 18 minutes; "Nickel Smelting," 18 minutes; "Nickel Refining," 9 minutes; and "Copper Refining," 6 minutes.

Jan 1, 1941

By Kenneth H. Johnston

The Weber pool in Washington County, Okla. (fig. 1), covers an area extending from 2 miles east and slightly north of Bartlesville, Okla., to a point approximately 2-1P tiles northeast of Dewey, Okla. The pool is a part of the area designated by the Standing Committee on Oil Field Nomenclature, Kansas-Oklahoma Division, Mid-Continent Oil & Gas Association, as the Bartlesville-Dewey field. In the following discussion of the geology, development, and exploitation of the Weber pool, the writers, by means of structure maps, cross sections through various parts of the reservoir, and tabulated development data and production statistics, have recorded salient information on a field that was developed before .1910 in an Area that has been repressured since 1926. The total oil production to January 1, 19.0., from the 2,639 developed acres considered in this report, was approximately 14 million barrels, or a recovery of about 5,3;2 barrels per acre, or 227 barrels per acre-foot. The production of the estimated 18 million barrels of recoverable oil remaining in the Bartlesville sand reservoir will require the initiation of additional secondary-recovery practices on some of the leases and the application of a more systematic repressuring program on others.

Jan 1, 1950

By Caio Moreira, Saulo De Rezende, Nelly Ruíz

The present project sought alternatives for this material through the Mining Lab Beginnings program, which was developed by Nexa in partnership with Escalab to find solutions for the company's highly complex challenges. Through the program, several solutions were evaluated, with additives for the construction market being the most prominent. Tests were conducted to confirm the efficiency of jarosite in the mixture that composes this material. With successful laboratory tests, the technology was tested on an industrial scale, where it also demonstrated its technical and economic viability. The project is now moving into the operational phase, demonstrating that circular economy is the best solution for disposed tailings.

Sep 29, 2023

By A. Javadi

"Our recent studies revealed that the sulfide minerals in contact with water during grinding produced hydrogen peroxide (H2O2) where the amount of H2O2 production by the minerals found to be in the order of pyrite > chalcopyrite > sphalerite > galena. The H2O2 effect on the oxidation of pulp components and its influence on the concentrate grade and recovery in flotation have been studied and the results have been presented and discussed in this paper. Studies have also been carried out to build correlation between percentage of pyrite in the concentrate, grinding conditions and concentration of OH•/H2O2 in the pulp and as well of controlling the formation of these species through known chemical means for depressing the generation of the oxidant. Flotation tests using a complex sulfide ore with the same reagent scheme that is being used at Bama concentrator in Iran but with the addition i) Na2S reductant and ii) inorganic (EDTA) and organic (TETA) surface modifiers, during grinding stage have been performed to judge the beneficial or detrimental role of H2O2 on the selective flotation of sulfides. The results demonstrate that the selectivity of metal sulfides against pyrite increases with increasing generation of H2O2 in the pulp liquid.INTRODUCTIONOur recent studies have illustrated the formation of hydrogen peroxide (H2O2) by metal-sulphides during grinding in the presence and absence of oxygen (Javadi Nooshabadi & Hanumantha Rao, 2013a; Javadi Nooshabadi & Hanumantha Rao, 2013b; Javadi Nooshabadi & Hanumantha Rao, 2013c; Javadi Nooshabadi & Hanumantha Rao, 2014). In the absence of oxygen, it was found that pyrite surface is catalytically active and able to breakdown water molecules to form OH• free radical and thereby deriving oxygen in the formation of H2O2 from water molecules. The in-situ formation of H2O2 and its influence on sulphide flotation has not been addressed yet. The presence of strong H2O2 oxidant in the pulp liquid and its selective oxidation of pyrite would be beneficial in depressing pyrite flotation. Therefore, it is important to build correlation between percentage of pyrite in the concentrate, grinding conditions and concentration of OH•/H2O2 in the pulp as well as to study possible ways of flexibly controlling the formation of these species through known chemical means for depressing the generation of the oxidant."

Jan 1, 2018

By Betty L. Gibbs

A company must have an organized approach to effectively sort through the profusion of available software and hardware and find the programs and equipment which fit defined needs. The selection process must build a complete compatible system which includes hardware and software. The methodology presented in this paper helps identify some of the more important considerations. The steps needed for an organized approach to software/hardware selection are: •All involved staff should contribute to an assessment of current computer capabilities and projection of future needs. •Alternatives are analyzed to determine what software and hardware is available and how selections may possibly be merged into the existing computer system. The evaluation process focuses on details of program capability and hardware compatibility. Analysis must be done to determine how closely individual programs fit the established requirements. The final decision is often a balance of needs between program capabilities and hardware availability. Any programs selected must be able to run on existing and newly purchased hardware. Any additional hardware selected must be capable of meshing with the available computer system.

Jan 1, 1983

By Kr. J. Dedelyanova

Selective flocculation of iron minerals could improve the economics of high intensity magnetic separation as concomitant process. When the minerals are finely disseminated is necessary a finer grinding to be applied which generates a lot of slimes. The HIMS is not enough efficient for particles below 20 microns ? territory where the selective flocculation is already well known industrial practice, so the combination of these two methods of beneficiation can bring a higher grade at high recovery to be achieved. The dynamics and selectivity of the precipitation process is studied in batch tests with flocculant starch and dispersants sodium silicate and sodium hexametaphosphate. The influence of preliminary conditioning with nitrogen acid at pH 2 before flocculation is also investigated. Flowsheet including these two methods is tested and the distribution of iron is shown.

Jan 1, 2014

By P. R. Taylor

A cyclone reactor system for the partial reduction and melting of taconite concentrate fines has been engineered, designed and operated. A non-transferred arc plasma torch was employed as a heat source. Taconite fines, carbon monoxide, and carbon dioxide were fed axially into the reactor, while the plasma gas was introduced tangentially into the cyclone. The average reactor temperature was maintained at above 1673 K (1400 C), and reduction experiments were performed under various conditions. The influence of the following parameters on the reduction of taconite was investigated: carbon monoxide to carbon dioxide inlet feed ratio, carbon monoxide inlet partial pressure, and average reactor temperature. The interactions of the graphite lining with carbon dioxide and taconite were also studied.

Jan 1, 1993

By Philip C. Good

Unweathered low-grade calcareous phosphate rock of about 20 percent P205 grade was beneficiated by a procedure in which contained carbonates were decomposed by calcination at about 1,000° C. On quenching the hot calcined rock in water, major impurities passed into a slime phase which was mechanically separated from a coarser concentrate fraction. Phosphate rock of two major types was beneficiated in batch-scale studies yielding concentrates containing 31.3 to 38.5 percent P205 at recoveries ranging from 54.8 to 86.0 percent. The samples were from two major deposits in India. Processing information gained was utilized in extending the work to a continuous-flow system, processing phosphate rock at rates up to 157 kilograms per hour. Superphosphate exceeding 16 percent water-soluble P205 was prepared from concentrate derived from continuous-flow processing.

Jan 1, 1976

By K Muller, T Oosthuizen

Blast exclusion zones are instrumental in protecting equipment and personnel. When there is no constraint in footprint, the exclusion zone can be enormous, practically eliminating the hazard of flyrock. Unfortunately, this may not always be the case and in many circumstances the blast design needs to be altered to suite such scenarios. When a conservative design approach is taken, it could completely eliminate any form of ejection, whether it is from the free face or the bench itself. The degree to which typical flyrock models describe fragment motion through air with ballistic flight equations are not justified when such a high level of control is applied. This paper examines various methods of risk analysis and suggests an approach to be used for controlled blasting.The outcome of principles discussed in this paper can be seen in video form (Mavmedia, 2014).CITATION:Muller, K and Oosthuizen, T, 2015. Should the blast exclusion zone be based on a qualitative or quantitative analysis? A practical implementation conundrum, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 425–428 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Michael M. Hamilton

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied a 37,542-acre portion of the 57,002-acre Riordan?s Well Wilderness Study Area (NV-040-166) in order to evaluate its mineral resources. The area studied is located in Nye County, NV, about 60 miles southwest of Ely, NV. Subeconomic mineral resources of limestone and sand and gravel were identified in the study area. The Troy and Irwin mining districts, 4 miles to the west, were active between 1868 and 1963, producing small amounts of gold, silver, lead, and tungsten from mines well outside the study area. Except for minor prospecting activity, most mining activity in the study area has been since 1980, consisting of claim locations and geochemical surveys.

Jan 1, 1987

By Spencee L. Willett

In 1984, at the request of the Bureau of Land Management, the U.S. Bureau of Mines conducted mineral surveys of the 20,508-acre Blue Lakes (NV-020-600) and 5,142-acre Alder Creek (NV-020-600D) Wilderness Study Areas (WSAs) in northwestern Humboldt County, Nevada. The WSAs are part of an upthrown, north-south trending fault block associated with the Basin and Range province. Both areas are predominantly underlain by the Cretaceous Duffer Peak pluton which intrudes Triassic metasediments and Jurassic plutonic rocks to the east and Permian Happy Creek volcanics to the south. In the Alder Creek WSA and in the southwest portion of the Blue Lakes WSA, Duffer Peak granodiorite and Happy Creek volcanics are overlain by Tertiary basalt. No active mines exist within the Blue Lakes WSA; but, several prospects, claims, and mineralized outcrops are in the south and northeast portions. No mineral resources were identified but samples from discontinuous, vein-type deposits contained anomalous amounts of gold, silver, copper, lead, zinc, molybdenum, antimony, and uranium. Very fine, residual gold was detected in nine alluvial samples collected from a small deposit in the southwest corner of the WSA; average gold value was $3.58 per cubic yard (at $350/ounce). Two mines, several prospects, and mineralized outcrops adjacent to the Blue Lakes WSA contain mineralized, irregular structures which do not appear to extend into the Blue Lakes study area.

Jan 1, 1986

By Khaled Morsy

Cementitious seals are made of foamed cements with strength ranging from 100 to 600 psi. These cementitious seals are usually used at locations where the seal will be subjected to some convergence, assuming that this material can absorb entry closure without compromising the structural integrity of the seal. Prior to 2006, Lake Lynn Experimental Mine (LLEM) conducted full-scale tests on various cementitious seals designed to meet or exceed the 20-psi horizontal static load requirements of the old 30 CFR1 75.335. Both hydrostatic and dynamic loading tests were conducted. The structural response (pressure and displacement readings) obtained from these tests were recorded. The stability of the cementitious seal is based on balancing the load applied to the face of the seal from the explosion against the shearing resistance at the seal/rock interface. Therefore, the properties of the seal/rock interface, such as stiffness, cohesion, friction, etc. are critical to determine the stability of a cementitious seal. These properties are usually assumed by the researchers in their models. This paper emphasizes the importance of having the correct properties of seal/rock interface in the numerical modeling. FLAC 3D models were developed to simulate Celuseal2 cementitious seals subjected to both hydrostatic and dynamic loadings. Using the hydrostatic and dynamic loading test data conducted at LLEM, the static and dynamic properties of the seal/rock interface were back calculated. The FLAC 3D models showed good agreement with the test results.

Jan 1, 2009

By Charles Camsell

MORE than one-third of all Canada is embraced in the federal domain known as the Northwest Territories. Its most northern point, Cape Columbia, on Ellesmere Island, is only 500 mi. from the Pole. It includes parts of the main physiographic divisions of the North American continent. In the West there is a strip of 30.000 sq. mi. lying in the Cordilleran region, where peaks in the Mackenzie Mountains rise as high as 8500 ft. East of this strip and extending roughly to a line through Great Bear and Great Slave lakes to the Arctic coast is a section of the interior plains. This section, known as the Mackenzie Lowlands, contains the great artery, the most striking feature of the Northwest Territories-the Mackenzie and Slave river waterway impressive in its width, almost two miles in places, and in it's navigability for 1357 miles without obstruction to the sea. Adjoining the Mackenzie Lowlands on the East is the greater portion of the mainland of the Territories, which, as well as a large share of the island area, is in the Canadian Shield.

Jan 1, 1937

By M. H. Stanczyk

The Bureau of Mines made bench-scale laboratory tests on a sample of typical Florida phosphate slime to determine alumina and phosphate extractions obtainable by agitation leaching, by baking and curing, and by a leach-electrolysis scheme. Recovery of mineral values from leached slime pulps by resin-in-pulp ion exchange contact and the reaction of the leached pulps to filtration, flocculation, and settling were also investigated. The best extractions of alumina and phosphate were obtained by (l) agitation leaching with sulfuric, hydrochloric, or nitric acid at an elevated temperature or (2) curing or baking the slime with sulfuric acid. Alumina extractions ranged from 80.8 to 90.0 percent and phosphate extractions ranged from 93.3 to 98.4 percent when the slime was leached at 90° C with sulfuric, hydrochloric, or nitric acids. Baking the slime with sulfuric acid at 200° C for 4 hours yielded an alumina extraction of 92.3 percent and a phosphate extraction of 97.0 percent, whereas curing with sulfuric acid at 100° C for 24 hours gave slightly higher alumina and phosphate extractions. Flocculation and settling properties of the slime were virtually unaffected in all cases. Filter area requirements, although somewhat improved as compared to untreated slime, remained relatively high. The lowest filter area requirement obtained was 44 square feet per ton of dry solids treated per day. Contacting leached slime pulps with ion exchange resins depleted the leach pulps of solubilized values; however, the filtration and settling properties of the barren pulps were unaffected. A leach-electrolysis scheme resulted in some concentration of solubilized phosphorus, but the method showed little promise of being commercially feasible.

Jan 1, 1966

By J. F. Papp

The microstructures of a CF2Br2-inhibited methane flame and its uninhibited analog have been determined using molecular beam-mass spectrometry. The slightly lean flames were stabilized on a cooled porous plug burner at reduced pressure. Composition profiles of stable, intermediate, and radical species and temperature profiles were obtained. Comparisons of the uninhibited and inhibited flame profiles revealed the following inhibition effects; a shift of the primary reaction zone to higher temperatures, a higher maximum flame temperature, an increase in the CH3 concentration, and a reduction in the H2CO, H, 0, and OH concentrations. Kinetic analyses of the data yielded rate coefficients at flame temperatures for the reactions H + CH4 ? CH3 + H2, H + O2 ? OH + O, CO + OH ? CO2 + H, and CH3 + O ? H2CO + H. CF2Br2 is judged to decay by thermal decomposition and abstraction reactions.

Jan 1, 1981

By S. Niyomwas, R. G. Reddy

"A mathematical model was developed to describe the plasma gas and particle dynamics and conversion yields. The velocity and temperature fields in the plasma were calculated by solving 1 the Navier-Stokes equations and the thermal energy balance equations. Conservation equations for the system species consider the multi-component diffusion and chemical reactions. Through the application of this model, temperature distribution, flow fields, and production rates were computed. The model was used to study the thermal decomposition of ilmenite in the non-transferred arc plasma reactor. The computed production rates of TiN from ilmenite using nitrogen and methane gas mixtures, are in the range of 5 to 100 x 104 kg/m3/s at 2500 KIntroductionThe widespread interest in thermal plasma processing has stimulated a great deal of research effort into the various aspects of this process, including plasma' spraying, thermal plasma chemical vapor deposition, plasma synthesis of fine powders, thermal plasma decomposition, plasma melting, and plasma extractive metallurgy.In the plasma synthesis of fine powders, the earlier experimental and theoretical studies aimed at predicting the final products1-5. Then it was followed by more recent investigation concerning the profile of plasma gas velocity, plasma temperature and concentration. In this regard, useful plasma processing models have been reported by numerous investigation6 -11 which were increased by both theoretical analysis and measurement.As a result of this work a reasonable plasma-processing model is proposed. It is to be noted that all the thermal analysis that has been made neglected the fluid -flow effects. Also, in the analysis aimed at the quantitative description of the fluid-flow field, the effect of heat transfer was not taken into account."

Jan 1, 2000

By G E. Holt

Active EM subsurface imaging is a proprietary technique developed by Marschall Acoustics Instruments Pty Limited (MAI) to image subsurface features at depths useful for the mining industry. Similar in field operations to high resolution seismic surveying, the Active EM technique employs electromagnetic energy rather than elastic wave energy. Received backscattered energy in the Active EM technique is thus due to differences and contrasts in electromagnetic permeability and permittivity in the subsurface, analogous to LamTÆs constants in elastic wave imaging. Carrying the analogy to seismic imaging even further, the Active EM method employs high power transmissions of very wide-band coded signals of a controlled polarisation. Likewise, the array pattern and polarisation of the receiving transducers is also tightly controlled. Thus, in a certain mathematical sense, Active EM is the electromagnetic equivalent of high power high resolution vibroseis seismic surveying. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Ronald W. Schaefer

This report describes operations at the Rosiclare Fluorspar Works of the Aluminum Co. of America at Rosiclare, Hardin County, Ill. The works include the Fairview mine, the fluorspar mill, and related facilities. The publication covers exploration, development, mining and milling practices, mine-drainage problems, and other activities and is presented as part of the Bureau of Mines series of publications on mining and milling practices in various parts of the United States. The Rosiclare fluorspar area, for its size, has been the largest producer of high-grade fluorspar in the United States and probably in the world. The vein system in this area is over 5 miles long and 1/2 mile wide, and ore has been found as deep as 900 ft.

Jan 1, 1961