Search Documents

By B. M. Bird

For several years the U.S. Bureau of Mines and the University of Washington have been cooperating, in a study of coal tabling. The first pert of the work consisted of experiments using, one of the commercial-sized coal washing tables in the laboratories of the College of Mine. As an outgrowth of this work, hindered-settling classification has been successfully applied in the tabling of coal4, and several important improvements, mainly in the riffling, have been made in the table itself. Both of these developments have resulted in increasing the rapacity and efficiency of the coal-washing table. In order to facilitate further progress in this work an investigation has been undertaken to throw more light on the mechanism of table separation. The final separation of a table is obviously the resultant of several operations; namely, stratification, removal of the top strata or parts of them as washed coal by the cross-flowing water, and removal of the bottom strata or parts of

Jan 1, 1929

By Alexandra Yuyali

The objective of this research work is to increase the drilling ratio represented in tons per drilled meter (ton/m) to reduce mining costs. One of the key characteristics of this research is the use of the ITH (in-the-hole) drilling rig with a water-powered hammer, also known as Wassara™. The patented Wassara™ in-the-hole hammer is powered by high-pressure water instead of air. To reach the objective, a new design of the blast pattern was implemented considering the following: Burden from 1.7 m (5.6 ft) to 2.8 m (9.2 ft) Spacing from 1.7 m (5.6 ft) to 2.7 m (8.9 ft) Drill diameter from 89 mm (3.5”) to 102 mm (4”) Drilling length from 15 m (49 ft) to 30 m (98 ft) Borehole deviation < 2% The result of this new design is the optimization of the drilling ratio (ton/m); having as a baseline 5.2 ton/m with traditional equipment and obtaining 13.7 ton/m with the ITH drilling, which generates annual savings of $2.43M.

Jan 21, 2025

By Michael J. Friedel

The fundamental problems associated with ground control reflect the inability of mining personnel to "see" the development of anomalous conditions. Toward this end, the U. S. Bureau of Mines is investigating the application of seismic refraction tomography for imaging the process of pillar yielding, at the Foidel Creek coal mine, near Steamboat Springs, CO. The inherent three-dimensional problem of imaging coal pillar stress is reduced to a single plane by considering only the stress transmitted from the pillar to the adjacent floor rock. This approach exploits the fact that refracted seismic energy is essentially confined to the adjacent higher velocity sandstone strata. The tomographic analysis using ray-tracing based on wavefront migration resulted in a robust P-wave tomogram from which regions of high velocity indicate zones of high stress concentration, whereas low velocity zones indicate regions of stress relief. The interpreted region of high stress concentration occurs at the pillar end nearest to the working face of the adjacent longwall panel. This finding is corroborated by vertical pressure cell measurements recorded in the pillar. The stress diminishes toward the pillar perimeter with local minima correlating to the locations of observed pillar spalling. Time-sequence monitoring, as the longwall face advances, is recommended for evaluating changing stress conditions.

Jan 1, 1993

By I. Milton LeBaron

Operation of the phosphate flotation plant at the Peace valley mine of the International Minerals and Chemical Corporation, Florida, began in the summer of 1942. Since that time several changes have been made in the flowsheet, with resultant increases in metallurgical results. Three flowsheets, together with the comparative plant results, are given in this paper, together with a discussion of the desliming circuit used for preliminary washing of the flotation feed. Fig. I lists the essential units in the original flowsheet at the Peace Valley plant. The figures for tonnage and grade are average for a period of two months. Mineral Separation Airflow cells are used for both the fatty acid and the amine float. Three immediate difficulties presented themselves in the use of this flow sheet: I. Floating a maximum amount of phosphate in the rougher section to give good recovery sent a low-grade concentrate to the silica float, resulting in high costs for amine reagent in that section.

Jan 1, 1947

By I. Milton LeBaron

Operation of the phosphate flotation plant at the Peace valley mine of the International Minerals and Chemical Corporation, Florida, began in the summer of 1942. Since that time several changes have been made in the flowsheet, with resultant increases in metallurgical results. Three flowsheets, together with the comparative plant results, are given in this paper, together with a discussion of the desliming circuit used for preliminary washing of the flotation feed. Fig. I lists the essential units in the original flowsheet at the Peace Valley plant. The figures for tonnage and grade are average for a period of two months. Mineral Separation Airflow cells are used for both the fatty acid and the amine float. Three immediate difficulties presented themselves in the use of this flow sheet: I. Floating a maximum amount of phosphate in the rougher section to give good recovery sent a low-grade concentrate to the silica float, resulting in high costs for amine reagent in that section.

Jan 1, 1947

By B. Matsetela, S. Amos, V. Nkuna

"The Kamoa-Kakula copper project—a joint venture between Ivanhoe Mines, Zijin Mining Group Co. Ltd, and the government of the Democratic Republic of Congo—has been independently ranked as the world's largest undeveloped high-grade copper discovery by international mining consultant Wood Mackenzie. It is a very large, near-surface stratiform copper deposit with adjacent prospective exploration areas within the Central African Copperbelt, approximately 25 km west of the town of Kolwezi and about 270 km west of the provincial capital of Lubumbashi. A phased development approach is currently envisaged. The first phase of the project involves the development of a 6 Mt/a underground mine and surface processing complex (dual stream concentrator) at the Kakula deposit, a discovery announced in early 2016. The second phase involves an integrated 12 Mt/a two-stage development, beginning with initial production from the Kakula mine, to be followed by a subsequent, separate underground mining operation at the nearby Kansoko mine, along with the construction of a smelter. Project description and locationThe Kamoa–Kakula project comprises a newly discovered, very large stratiform copper deposit with adjacent prospective exploration areas, located within the Central African Copperbelt in Lualaba Province, Democratic Republic of Congo (DRC). The Kamoa–Kakula project lies approximately 25 km west of the town of Kolwezi and about 270 km west of Lubumbashi. Ivanhoe owns a 49.5% share interest in Kamoa Holding, an Ivanhoe subsidiary that currently owns 80% of the project. Zijin Mining owns a 49.5% share interest in Kamoa Holding, which it acquired from Ivanhoe in December 2015 for an aggregate cash consideration of US$412 million. The remaining 1% interest in Kamoa Holding is held by privately-owned Crystal River.The Kamoa–Kakula project consists of the Kamoa exploitation licences (exploitation permits 12873, 13025, and 13026, which cover an area of 397.4 km2) and one exploration licence (exploration permit 703 covering an area of 12.74 km2). The Kamoa exploitation licences, approved 20 August 2012, grant Kamoa Copper the right to explore for, develop, and exploit copper and other minerals, for an initial 30-year term, expiring on 19 August 2042. The permits can then be extended for 15-year periods until the end of the mine’s life."

Nov 1, 2018

By R. D. Taylor, Jim Douglas Jr., H. H. Rachford Jr., P. M. Dyke

A major obstacle to the use of wetting agents in .secondary recovery by water flooding is the adsorption of the agents on the sand. As a result of adsorption, the surfactant always lags behind the floodwater front. Consideration of the chromatographic theory of adsorption indicates that the detergents will not lag as much if used in very high concentrations. An investigation was made of the possibility of using high concentrations economically by flowing slugs of wetting agents followed by normal flood water. The experiments consisted of adsorption studies on Alundum powder and Berea sandstone. Flow rests on a 12-in. Alundum core and 22-in. Berea core were used to determine rate of detergent movement. The results of the flow experiments indicate that the relative rate of surfactant advance is, indeed, sensitive to the concentration of the agent. A 10 per cent slug moved with a rate that war 78 to 95 per cent as fast as the rate of advance of the flood water. By contrast, one with 25 ppm (the number of parts of commercial detergent in a million parts of water on a weight basis) concentration moved less than one-fourth as fast as the flood water, and calculations indicate that in very long porous systems the rate of movement of the lower concentrations will be a small fraction of the rate of advance of the flood front. The results. of the adsorption studies were utilized to calculate the rate of advance of the detergent when only the initial concentration was known. The calculated rates showed substantial agreement with the experimental flow tests in the high concentration ranges. The adsorption results were also used to estimate the cost of the materials for a slug-type surfactant flood in the field. In addition to the faster rates of movement, the concentrated detergent slugs removed much more oil than the dilute solutions. However, the effectiveness of the slug process depends on many variables. The quantity of oil removed is increased markedly by increasing the flooding rate. The efficiency is also influenced by the type of crude, type of reservoir rock and initial water saturation. Therefore, a careful analysis of each reservoir system is required before the economic value of the process can be determined. INTRODUCTION It is well known that the displacement of oil by invading water during water flooding is far from complete. It is generally agreed that the unrecovered oil is retained in the porous medium by the capillary forces which may be relatively large compared to the forces generated by the flowing water. Therefore, it was logical that some early workers should turn to surface-active materials to reduce the capillary forces to facilitate the release of oil. As early as 1927,&apos; a patent was granted for the use of surface-active materials in water flooding. In 1932, when soap solutions were passed through Bradford and Venango sands, it was reported that the results were inconclusive, erratic and that "further investigation is needed to determine exactly the function of the solution and to obtain a clearer insight into the phenomena involved."&apos; Some of the modern scientific reports conclude with a similar statement,&apos; showing that the lack of agreement on the mechanism of oil removal by wetting agents is still very widespread even though several comprehensive studies have been reported.&apos;." Although there is a lack of agreement as to the general effectiveness of the detergents for water flooding, most investigators do agree that all of the common detergents are strongly adsorbed onto the solid surfaces of the reservoir. In the early calculations it appeared that all additives would be lost before reaching much of the formation area which contained the additional oil to be removed. Experiments indicated that if the usual small waterflood concentrations of wetting agents were used, the rate of advance of detergent through the formation would be only a small fraction of the rate of advance of the flood front. Indeed, some investigators4 felt that the use of wetting agents would never be economically feasible because of their adsorption. For example, DunningG estimated that the wetting agent in concentrations of 25 ppm, would advance only 0.05 times as fast as the flood front. Ojeda, et al,&apos; found that a surfactant in a concentration of 10 ppm moved less than 0.01 times as fast as the flood front. It is significant, however, that both investigators found that increased concentrations of wetting agents moved faster, relative to the flood front, than solutions at the lower concentrations. Ojeda showed that an extrapolation of his data indicated a relative rate of 0.5 at 1 per cent concentration, while Dunning6 estimated a relative rate of 0.46 for a 1 per cent concentration. It was obvious that these concentrations could not be used for continuous injection because the cost of the injected detergent would far exceed the value of additional oil produced. Traditionally, detergents are used in very low concentrations for they show good

By I. Milton LeBaron

OPERATION of the phosphate flotation plant at the Peace Valley mine of the International Minerals and Chemical Corporation, Florida, began in the summer of [ ] 1942. Since that time several changes have been made in the flowsheet, with resultant increases in metallurgical results. Three flowsheets, together with the comparative plant results, are given in this paper, together with a discussion of the desliming circuit used for preliminary washing of the flotation feed. FIRST FLOWSHEET CHANGES Fig. I lists the essential units in the original flowsheet at the Peace Valley plant. The figures for tonnage and grade are average for a period of two months. Mineral Separation Airflow cells are used for both the fatty acid and the amine float. Three immediate difficulties presented themselves in the use of this flow sheet: I. Floating a maximum amount of phosphate in the rougher section to give good recovery sent a low-grade concentrate to the silica float, resulting in high costs for amine reagent in that section.

Jan 1, 1946

By John Ward Smith

This paper describes and evaluates a method that the Federal Bureau of Mines used to determine the ultimate composition of the organic material in 10 samples of oil shale from the Mahogany zone of the Green River formation in Colorado and Utah. Since interest has centered on the Mahogany zone, the richest section of the deposit, these 10 samples were chosen to provide a broad representation of this zone with the objective of obtaining generally valid ultimate composition values. The most probable organic composition for the Mahogany zone and the 95-percent confidence limits for each component average (in weight-percent of organic material) are: Carbon 80.5 ± .4 Hydrogen 10.3 ± .1 Nitrogen 2.4 ± .1 Sulfur 1.0 ± .1 Oxygen 5.8 ± .5 As only minor variations in composition were observed, the organic material of this particular bed is quite similar over a wide geographic area.

Jan 1, 1961

By Hajime Kitamura, Nobuharu Isago, Yuta Yamanishi, Kosuke Kawata, Hiroshi Yagi, Akira Matsuoka

Mountain tunnels are generally considered to be stable during earthquakes, however, it is known that the portal areas are prone to seismic damages. Characteristics in portals such as the location of the slope, modulus of ground deformation, and the change of overburden are different for each tunnel, and damage degrees are unclear. In this study, we reproduced the seismic behavior to investigate the effect on the tunnel portal by considering some parameters above, using simple static model tests and numerical analysis. As a result, the conditions of the slope condition and minimum distance from slope was confirmed to influence on the mechanical behavior of the tunnel portal during earthquakes.

Dec 1, 2022

By Eckhard Nembach

The phase diagram of the system Pb-In has been investigated between -27° and + 40°C, using nzainly X-ray dijfraction. In accordance with t her mo dynamic measurements by Heumann and Predel, a segregation occurs at low temperatures, though not in the form of a nziscibility gap. THE phase diagram of the system Pb-In has been the subject of extensive investigations,1&apos;1 but recently Heumann and prede13 concluded from their thermodynamic data that a new feature should occur below room temperature. These authors observed that the maximum values for the enthalpy and entropy of mixing, which occurred at a composition of 50 at. pct Pb, were +400 and —1.7 cal per g-atom deg, respectively. From this the authors estimated that a miscibility gap should occur below 30°C, centered at 50 at. pct Pb. Resistivity measurements seemed to support this view. These authors proposed the phase diagram outlined in Fig. 1. Three phases exist at 30°C: the tetragonal indium phase with c/a > 1, the tetragonal intermediate phase a, with c/a < 1, and the fcc lead phase. During an investigation of the superconducting properties of Pb-In alloys. it has been observed4 that aging a specimen with 50 at. pct Pb for 14 days at -18°C decreased the superconducting transition temperature about 0.13"K and tripled the transition width. In this paper, the results of an investigation of the Pb-In phase diagram in the temperature range from — 2T to +40°C are reported. Superconductivity and X-ray methods have been used. 1) SPECIMEN PREPARATION The materials were provided by the American Smelting and Refining Co. According to the manufacturer their purity was 99.999 pct. The weighed amounts of the constituents were sealed in quartz tubes under an atmosphere of 10 torr helium, mixed for 24 hr in a rocking furnace at 380°C, quenched in ice water, and homogenized at 20" to 30°C below the solidus line, established by Heumann and Predel. The annealing times were 144 hr for specimens containing Less than 30 at. pct Pb and 36 hr for the remainder. 2) SUPERCONDUCTIVITY EXPERIMENTS The specimens were quenched from the homogeniza-tion treatment into ice water and their superconducting transition temperatures T, measured. The procedure used has been described in Ref. 4. The transition was detected by the change of the mutual induc- tance of two coaxial coils containing the sample. T, was defined as the temperature at which 50 pct of the total change in inductance had occurred. The repro-ducibility with which T, could be measured was i0.002"K. Then the specimens with lead contents between 38 and 75 at. pct were aged for 7 days at temperatures between -30" and 40°C. If this treatment caused T, to change by more than 0.005"K or the width of the transition to increase by more than 0.002"K, it was concluded that the specimen had undergone a phase change and no longer consisted only of the fcc lead phase: as it did immediately after homogenizing. The result is shown in Fig. 2. From this one can estimate at what temperatures and concentrations phase changes occur. The X-ray measurements were based on these preliminary results. 3) X-RAY EXPERIMENTS Because of the softness of the material, relatively coarse powders. 75 p, had to be used, which were filed in a helium atmosphere from homogenized specimens. The powders were annealed at least 30 min at temperatures between 120" and 16OJC, depending on their concentration, and quenched in ice water. Then their X-ray patterns were taken at -178°C with a Picker diffractometer, model 3488K, and a cold stage. on which the specimen was in thermal contact with a liquid-nitrogen reservoir. In this way the following relation was established for the fcc lead phase: a = 4.697 + 0.00247C for 40 5 C 5 75 11 where n is the lattice constant (A) and C is the at. pct of lead. The coarseness of the powder made it impossible to use lines with 0 > 75 deg; therefore n was averaged from lines with 45 deg 5 0 5 75 deg. The results were reproducible to within i0.05 pct. Relation [I] is very similar to the one found by Heumann and Predel at room temperature. Following this, homogenized specimens with compositions between 15 and 56 at. pct Pb were aged for at least 10 days at temperatures between -27" and

Jan 1, 1970

By Harry R. Hall

The proposition to make pig-iron from magnetic concentrates and cobbed ore with charcoal-fuel weighing from 12 to 20 lb. per bushel is, on the face of it, not inviting; but the work that has been done under these adverse conditions may be worthy of record as furnishing a comparison with coke blast-furnace practice under similar conditions.&apos; The record of the furnace-practice is briefly summarized as follows :—the charcoal was made of hemlock, pine, spruce, balsam, maple, beech and birch woods. All the concentrates, containing from 62 to 65 per cent. of iron, would pass 1/8in. screen, of which about 34 per cent. would pass an 80-mesh screen. The cobbed ore, varying in composition from 32 to 47 per cent. of metallic iron and from 23 to 32 per cent. of silica, would pass through a 1-in. ring, and of this ore about 25 per cent. would pass a 1/8-in. screen. The furnace was blown-in October 20, 1903, with charcoal which was supposed to weigh, when dry, 18 lb. to the bushel. Some charcoal similar to this was stored in the stock-house for about a year, and was then found to weigh 12 lb. per bushel.

Jan 1, 1906

By William P. Walsh

In December 1983 the author undertook an investigation in east Texas which was organized to learn the feasibility of applying geophysical techniques over shallow lignite deposits. The work embraced experimental high resolution seismic reflection and offset Wenner resisitivity sounds over three 1/4 to 1/2 mile test sections. This site also was sponsored by Woodward-Clyde Consultants (WCC) and a consortium headed by North American Coal Corporation. The principal objective of this investigation was to learn whether the aforementioned geophysical techniques could be applied over shallow lignite deposits (i.e. located at approximately 100&apos; to 300&apos; in depth) and consequently provide structural and stratigraphic information useful for resource and reserve characterization. A secondary objective was to determine if these same techniques could disclose the nature of the overburden and the distribution of ground water therein.

Jan 1, 1986

By W. D. Mcmillan

Preliminary examination of the north-central Kansas clay deposits was made by the junior author during March 1943. He was accompanied by Norman Plummer, ceramist of the State Geological Survey of Kansas. Three areas Nacre selected for further investigation. Detailed field investigation by the Bureau, consisting of hand auger drilling, trenching, anti. test pitting to obtain representative samples of the clays was carried on from April to June 1943. Field .work was under the direction of Edgar B. Butte and Richard L. Schumacher, former Bureau of Mines engineers. The samples taken were analyzed at the Bureau of Mines laboratory at Rolla, Mo. Factual data obtained from the field investigation and laboratory work are set forth in this report.

Jan 1, 1948

By David Butts

Solar ponding to crystdlize sodium chloride has been used for thousands of years.1 The systems used were inefficient and usually small compared to the large 25,000 acre pond areas seen today. It has only been in the last 25 years that any real effort has been applied to develop solar ponding technology. Many large solar pond systems have been constructed without much thought to efficient and optimum production rates. The recent high costs of labor, of equipment and of energy have forced producers to take a closer look at their solar pond systems in an attempt to squeeze out the highest possible yields. Other companies such as the Arab Potash Company, the Dead Sea Works, Texas Gulf (Moab, Utah) and San Francisco Salt Companies have no more land area in which to expand and therefore efficient ponds are essential. This paper is written to show how the subdivision of solar ponds can result in production increases of up to 20% and beyond.

Jan 1, 1984

By R. F. Hehemann, R. H. Goodenow

Thermal arrest, hot-stage microscopy, and transtnission electron microscopy techniques have been employed to study the transformations in low-carbon iron and Fe-9 pct Ni alloys. In continuous cooling experiments, each alloy transforms at an essentially constant temperature for cooling rates below the critical rate required for martensite formation. However, high-tenzperature transformation in pure iron takes place by a different mechanism than that in the 9 pct Ni alloys. Pure iron exhibits an equi-a a structure with a low and random dislocation density while the 9 pct Ni alloy exhibits a cell or lathlike substructure analogous to that of low-carbon martensite. This same substructure characterizes upper bainite in higher-carbon inaterials. UNTIL relatively recently, diffusionless transformations have been considered to take place by the same mechanism and have been termed mar-tensitic transformations.l-3 The most characteristic feature2 of this mode of transformation is the shape change produced by a shear deformation and growth of the product phase frequently occurs at an extremely high velocity approaching that of an elastic wave.4&apos;5 A different mechanism of diffusionless transformation was recognized first in Cu-Ga and other copper-base alloys.6,7 From the absence of surface tilting in these alloys, it has been concluded that transformation is not accomplished by the cooperative shear displacements that occur in mar-tensitic reactions. Transformation presumably takes place by the rapid movement of an incoherent interface which is capable of propagating across parent grain boundaries. Although the transformation is diffusionless in the macroscopic sense, advancement of these interfaces is accomplished by an atom by atom rearrangement. Transformations of this type therefore require thermal activation and are generally operative only at high temperature. Although requiring short-range diffusion at the interface, propagation still occurs so rapidly that the reaction cannot be suppressed with normal cooling rates.7 The resulting microstructures exhibit large, irregular-shaped regions of the product phase, which are essentially free of crystallographic features. Consequently, these reactions have been termed massive transformations. Transformation by the massive mechanism has been reported to occur in ferrous systems involving pure iron and binary alloys of iron with nickel, chromium, and silicon by Gilbert and owen.&apos; The Fe-Ni system is of special interest in that the massive transformation was observed in alloys with less than 15 pct Ni while alloys having more than about 28 pct Ni transformed by the conventional mar-tensitic mechanism. By employing cooling rates substantially higher than those used by Gilbert and Owen, Swanson and Parr have been able to suppress the massive transformation in alloys with 0 to 10 pct Ni9 and produce martensite as revealed by surface relief. The massive transformation in the alloys having less than 15 pct Ni was identified by the lack of surface relief and an irregular rather than clearly acicular microstructure.&apos; Speich and Swann, using thin-foil electron microscopy, identified three distinctly different structures10 in quenched binary Fe-Ni alloys. From 0 to 4 pct Ni the structure consisted of blocky grains of a with a low and random dislocation density. Alloys with 4 to 25 pct Ni exhibited a cell structure with a high dislocation density; and at greater than 25 pct Ni the structure consisted of internally twinned plates. The structural change at approximately 4 pct Ni suggests that alloys with low nickel content transform by a different mechanism than those with intermediate nickel contents and the transition from the cellular to the internally twinned structures at approximately 25 pct Ni is analogous to the transition from needles to internally twinned plates that occurs over a narrow range of carbon contents in Fe-C martensites.11,12 Conventional bainitic and martensitic modes of austenite decomposition operate in ternary Fe-C-Ni alloys having less than 10 pct Ni. This investigation was conducted in order to explore the conditions under which the massive, bainitic, and martensitic transformations occur and the relationships between these modes of decomposition.

Jan 1, 1965

By W. A. Lang

"IntroductionCARBONIZATION, gasification, and chemical utilization of coal are interrelated topics, which makes it difficult to review one without indicating its connection with the others. Hence, in Progress in Coal Technology, Series No. 5: Carbonization, reference was made to gaseous products recovered in the carbonization of coal, and .to a number of chemicals made from the tars, light oils, and ammoniacal liquors which are by-products of coal carbonization.In this, the sixth paper in the review series, prime consideration will be given to the complete gasification of coal to give a fuel for domestic industrial, or power purposes and a synthesis gas suitable for the manufacture of gasoline, Diesel oil, and chemicals. The hydrogenation of coal, an alternative source of liquid fuels and of chemicals, will be reviewed, as will be a number of processes for •the recovery of chemical products from coal by extraction and chemical treatment."

Jan 1, 1952

By Auguste J. Rossi

As is well known, practically all the phosphorus of the ironores smelted in the blast-furnace passes into the pig-metal, increasing its fluidity, but diminishing its strength to such an extent that, if phosphorus exceeds a certain amount, the metal is only fit for fine castings, not required to resist strains, and it cannot be used for the ordinary purposes of good foundry-iron. No phosphorus being eliminated in the acid Bessemer process, the quantity admissible in pig-metal destined for that process must be very small, and hence the ores smelted must be strictly Bessemer ores, of which, in many districts, the supply is taxed to the utmost. On the other hand, very highly phosphoric pig, a metal of little or no value by itself, when refined by the Thomas-Gilchrist process in the basic converter, furnishes an excellent steel; but such pig-iron must be made from ores particularly high in phosphorus; and these ores are not everywhere abundant, and are much sought after for this special purpose. But there are many iron-ores containing a moderate, though still important, amount of phosphorus, which yield a pig-metal

Jan 1, 1897

By P. D. S. St. Pierre

IN REGENT YEARS, blast furnace operators have found it necessary to improve their technology in order to handle increasingly low-grade feed and yet satisfy the demands for greater tonnages of metal. Studies have been made covering several aspects of the problem, and in this connection the slags produced in the iron-making process have been critically examined with a view to discovering the slag with the optimum properties for a given operation. A good slag should combine, as far as possible, the properties listed in Table I. Unfortunately, some of these desirable properties are incompatible. For example, the advantage of the small ?bulk of a low-flux slag is offset by its low desulphurization potential and high viscosity. Similarly, a very fluid slag increases refractory wear. It will be seen, then, that a balance must he struck between these conflicting requirements. In the .present paper only the melting relationships of blast furnace slag ?compositions will be considered in detail. In interpreting the data herein presented, the optimum property requirements listed in Table 1 must strictly be borne in mind. It should also be noted that the discussion presented here always relates to calcined fluxes, since this facilitates reference to the final slag composition. Thus, in making calculations pertaining to the ?burdening of the furnace, due allowance should ?be made for the fact that the fluxes are added as carbonates.

Jan 1, 1956

By J. J. Bezuidenhout

The waste-heat boiler is used within the Sulphide flash smelting process as the main dust and energy recovery unit. The large volume of off-gas discharged from the flash smelter is at a very high temperature (1350°C) and contains a significant dust load that subjects the downstream waste-heat boiler to tough and demanding conditions. The boiler cavity is especially prone to dust accretions, fouling, and corrosion caused by accumulation of molten particles and precipitation of sulphuric acid. Computational fluid dynamics (CFD) is applied within a qualitative study to model the flow and heat transfer distribution throughout the waste-heat boiler. The commercial CFD package, Fluent 6.2.16, was applied to a modified waste-heat boiler (23 m ×11 m ×5.4 m) within the Outokumpu flash smelting process. This investigation focuses on the geometric modifications to the typical boiler design, which includes elevation of the ceiling, placement of flow-obstructing baffles and radiation plates parallel within the flow path. Also investigated were various boiler operating conditions such as the circulation of process off-gas, air leakage from the dust discharging hoppers and variation in inlet gas composition. The geometric modifications had the desired effect of increasing the volumetric utilization and therefore enhancing heat transfer between the boiler surface and the gas stream and dust segregation. Introducing circulated off-gas at a rate of 20 m/s and at a 45° angle to the front of the waste boiler further enhanced cooling while reducing the high impact of the furnace-uptake gas-stream on the boiler ceiling. The placement of radiation plates was found to be very effective in enhancing the heat transfer surface and distributing gas flow within the boiler. These results present recommendations towards an improved waste-heat boiler design. Keywords: flash smelting, waste-heat boiler, CFD simulation, off-gas cooling.

Jan 1, 2008