Search Documents

By Yunqing Tian, Wenbin Huang, Weidong Zhang, Xiaopeng Wang, Gele Qing, Xiangjuan Duan

Pellet production requires iron ore concentrates have fine particle size, high specific surface area and good balling performance, so iron ore concentrates appropriate for pelletizing is limited compared to sintering. In order to extend the iron ore resources for pelletizing, the iron ore fines for sinter are studied in this paper.The effect of grinded iron ores o npelletizing, roasting and pellet quality were studied in this paper. The bond grinding index of iron ore fine is between 12.5 and 16.98 kwh/t. The grinded iron ore fine has good balling performance, the drop number and compressive strength of green pellet were improved with increase of grinded iron ore fine ratio. The compressive strength of roasted pellets were decreased with increase of grinded iron ore fine ratio, however it can be reached 2500 N.P −1 while proportioned with more than 80% of magnetite iron ore concentrate.

Mar 1, 2018

By Henrique Hipolito, Caio Alves

Waelz process is a method applied in the zinc oxide production and is one of the largest sources of carbon emissions within the zinc industry. The solid carbon used for heating and for reduction reactions is provided mainly by the coke fed with the EAFD in the Waelz kiln. Both chemical composition and physical properties of the coke are important to transportation and to the process. Decarbonizing the Waelz process by replacing the traditional fuel source using alternative biogenic fuel, for example, offers a potential solution to reduce the carbon footprint, which is aligned with the ESG perspective.

Sep 29, 2023

By S. Banisi, A. Ghasemi, S. Zare, F. Ghorbani, E. Nematollahi

"Comminution is the most energy intensive operation which constitutes the major portion of operating and capital costs of the mineral processing plants. Working at the maximum operating capacity of comminution equipment plays a significant role in the efficiency of the circuit. Appropriate design of cone crusher feed box could result in the choked crushing which is known as a vital factor in achieving target performance. In this research, the non-uniform cone crusher feeding at the Sarcheshmeh copper complex was studied and appropriate measures were taken to solve the problem. The problem resulted in non-uniform and high wear rate of crusher liners and high fluctuations of power draw. In recent decades, the discrete element method (DEM) has been applied successfully to study the effect of different factors on the behavior of particles flow. In this work, various designs for feed box were tested using an in-house developed DEM software called KMPCDEM©. The best feed box design obtained from the simulations was selected, constructed and installed in of the cone crushers. The new feed box design resulted in more uniform feed distribution on the distributor plate of crusher indicated by a reduction of the standard deviation of power draw measurements from 13 to 3 kWh. The better control of the crusher, 49% increase in the crusher throughput and finer and narrower product size distribution were the main outcomes of the installation of the new feed box. Furthermore, the wear rate on mantle and liners of crusher not only decreased but it also became uniform.INTRODUCTION Comminution is the most energy intensive operation which constitutes the major portion of operating and capital costs of the mineral processing plants. Reaching the maximum operating capacity in comminution equipment is a key sign of approaching the nominal productivity of the process. Due to the effect of crusher efficiency on the downstream circuit performance, optimization of the crushing circuits has received considerable attention (Herbst, & Potapov, 2004; Quist, & Evertsson, 2010; Li, Huiqi, McDowell, Glenn R, Lowndes and Ian, 2014; Cleary, Sinnott, Morrison, Cummins, & Delaney, 2017). Improving the performance of crushing circuits not only decreases the capital and operating costs but also increases the efficiency of downstream grinding circuits (Jacobson, Janssen, & Urbinatti, 2010). In cone crushers particles can be subjected to two different modes of compressive breakage; single particle breakage (free feeding) and inter-particle breakage (choked feeding). The maximum efficiency of the cone crusher directly depends on the type of feeding arrangement (Operation Manual, 1977). An appropriate feeding must lead to choked feeding the cone crusher. If the rate and method of feeding the crushers are correctly be executed, the maximum efficiency of the crushers could be available (Jacobson et al., 2010)."

Jan 1, 2018

By H. D. B. Wilson, D. T. Anderson

"Canadian sulphide deposits generally have characteristic compositions. Metal associations in ore deposits and in igneous rocks are similar.Nickel: sulphur ratios, copper-nickel ratios, and nickel :cobalt ratios in copper-nickel sulphide ores are characteristic for most orebodies. Nickel, as sulphide, is highest in ores associated with ultrabasic rocks, whereas copper is highest in ores associated with gabbros. Cobalt is relatively constant. The metal ratios in copper-nickel ores are due, first, to the composition of the related igneous rock or magma; second, to the partition ratios of the metals into the sulphides when separating from the silicate rock or magma; and third, to the conditions at the time of deposition. Each factor is discussed and the evidence indicates the Frood orebody is a magmatic segregation in place and Falconbridge is an injected sulphide melt. Many Canadian orebodies containing copper, zinc, or lead also have relatively constant compositions. •Copper and zinc are concentrated in gabbro and diorite, and copper-zinc ores in northwestern Quebec are spatially related to gabbros and diorites. The same three factors con-trolling metal ratios in. copper-nickel deposits should control the metal ratios in copper-zinc deposits if the metals come from the gabbro-diorite intrusions.The ratios of base metals in common sedimentary rocks are not similar to the ratios in orebodies. Base metal elements are mobilized during high-grade metamorphism, but much fundamental research is needed before the relation between metamorphism and ore deposits can be established on a sound basis. The distribution of elements in sulphide orebodies suggests that cop-per, zinc, and lead are deposited simultaneously .in relatively constant proportions rather than successively in a paragenetic sequence. Zoning may be due to different ratios of metals being deposited under changing temperature, pressure, and chemical environment, or may be the result of other processes."

Jan 1, 1959

By L. J. E. Hofer

The Bureau of Mines determined rates of adsorption and desorption of methane as a function of particle size and temperature, using coals from the Pocahontas No.3 seam (lvb) from the Bishop mine of western Virginia, and the Pittsburgh seam (hvab) from the Pursglove No. 15 mine of northern West Virginia. For a given coal sample and temperature, the rate curves for adsorption and desorption are essentially the same when expressed on a fractional approach to equilibrium basis. The rates of adsorption and desorption increased eightfold as the particle size was decreased from 6-8 to 270-325 mesh per inch. The adsorption process appears to be diffusion controlled. Rate of sorption processes increased with increasing temperature; however, the amount adsorbed at equilibrium decreased.

Jan 1, 1966

By D. Harrington

Advocates of health and safety in mining have found themselves confronted in recent years with what might appear to be contradictory procedures with regard to dust occurrence in mines and what appear to be suitable methods or measures to give the mines and mine workers a maximum measure of protection against dust. A concerted and relatively effective drive has been made to introduce rock dust into bituminous and lignitic coal mines to prevent or limit explosion and fire disasters, while an equally determined effort has been and is now being made to curb rock dust or to eliminate it from air in metal mines to prevent or at least limit the occurrence of miners' consumption and other diseases. Both procedures are logical even though the efforts appear to be of an opposing nature. While rock dusting has not been applied in coal mines nearly as universally or as effectively as could and should be done, nevertheless a careful analysis of the record of the past 10 years indicates that the amount of rock dusting that has been done has resulted in the saving of a minimum? of 200 lives annually certainly no small achievement. Largely but by no means wholly due to the use of rock dusting, the number of fatalities from explosions and fires in our coal mines in the last 4 years haw been reduced more than 75 percent as compared with the 4-year period 1911-15, the first years of the existence of the United States Bureau of Mines, which was brought into existence in 1910 largely to try to do something about reducing the disgracefully high fatality occurrence from explosion disasters in our coal mines. Hence, rock dusting has been given at least a. trial and has proved its effectiveness definitely.

Jan 1, 1937

By K. Kim

"All milling operations would like to achieve the best possible recovery in combination with the highest achievable throughput. Unfortunately, many operations have problems with low recovery, low throughput or both. In the majority of these cases investigated by the author, the solutions to improve recovery and throughput were simple. The solutions did not include implementation of new technology or major capital, but rather a return to fundamentals. In most cases, problems occurred because the operation was not following their own operating procedures, because the design of the circuit was changed without adequate change management or understanding of the implications of changes, or because basic metallurgical measurements and control were not taken or ignored. In this paper, examples of these problems and their solutions derived from long and varied experience will be discussed. The objective of this presentation is to provide the milling operator with practical and readily implementable solutions to common milling issues to improve throughput and recovery.INTRODUCTION Mill operations can be evaluated by many operating parameters, but the two best indicators are recovery and throughput. These two parameters summarize the wellbeing of an operation. The grade to the mill is also a good indicator, but this is usually controlled by the mine. The best recovery and throughput are achieved through a team work involving operators, maintenance workers and metallurgical staff. The milling operations include many unit operations, such as crushing, grinding, flotation, leaching, carbon in leach, Merrill Crowe, roaster, autoclave and refinery. The tools available to the operations are plant design, process measurements, assays, metallurgical balance, and operating strategy. Twelve real life examples of improvements of recovery and throughput are presented in this paper. EXAMPLE 1: CRUSHING CIRCUIT WITHOUT FINE ORE BIN At this operation plant throughput could not be maintained at a high rate because feed to the mill became coarse during the day. The cone crusher was feeding the ball mill directly. As the day wore on, the gap on the cone crusher would slowly increase, which would cause the product size to increase. This would increase the re-circulating load on the ball mill. The throughput would decrease accordingly. Furthermore, the throughput would decrease more with high frequency of maintenance on the cone crusher."

Jan 1, 2019

By John Cowin, Dan McCutchen

Cowin & Company has specialized in underground construction since 1924. This paper reviews the sinking of two shafts in the Alabama coal fields using bulk-loaded explosives. Each shaft is eighteen hundred feet deep, and their diameters were twenty feet and twenty-three feet. The first consideration in changing to a new explosives system was safety. Safety began with the explosive supplier training the miners in the use of the new system, from explanation of the pumping unit on the surface to hands-on training in the shaft. The considerations covered include establishing a thunderstorm exit plan, and reducing exposure time of the crew to explosives while loading. The system consisted of a specialized pumping unit and an advance emulsion product. Eliminating the need for nitroglycerin based explosives, and reducing sensitivity to mechanical shock were goals that were met. Performance in the shaft and ease of use meant morale of the miners using the system remained high and positive. Performance benefits discussed include reducing the number of holes in the round, and cutting explosives loading time in half. Damage to the ribs of the shaft was greatly reduced, making it safer to work near the ribs on succeeding rounds. Cleaning the bottom before drilling the next round also showed marked improvement. The economics of the system became very apparent when cycle time saved was allocated against fixed cost of sinking these shafts.

Jan 1, 2000

By Luke Keeney, Stephen Walters

"The start up of a new mining and metallurgical facility is a crucial step in the life of any mining project. The mining industries record is poor when evaluating processing plant operation relative to design capacity predictions made during feasibility studies. Multivariate geometallurgical orebody characterisation, using principle component analysis, is a method developed for improving predictive processing performance models during feasibility stages of mine development. This paper outlines the application of multivariate geometallurgical characterisation to the Cadia East deposit located in New South Wales, Australia. Cadia East is a low grade high tonnage copper-gold porphyry system in advanced stages of feasibility analysis. A dataset of ~32000 measurements and 150 comminution parameters (A*b and BMWI) has been used to develop class-based characterisation and modelling methodologies. The results of this study outline the development of class-based ore characterisation and provide a technique for analysing and interpreting large and complex geometallurgical datasets for prediction and optimisation of processing performance. The results enable sophisticated population modelling to be conducted which displays deposit scale processing variability, aiding circuit design specifications and predictions during feasibility studies.INTRODUCTIONA feasibility study is the major technical report on which the decision to proceed to production and on which financing is based (Shillabeer & Gypton, 2003). The mining industry’s record is not very good when actual construction time, costs, and operating performance are compared to the projections made in feasibility studies (Ballard, 1983; Gypton & Ward, 2000; Gypton 2002). A study by McNulty (1998) found that of 41 mineral processing and chemical plants built between 1965 and 1995, only 56% achieved design capacity within two years of commissioning and three were closed after failing to achieve design capacity within 36 months of start up (Shillabeer & Gypton, 2003). McNulty (1998) related this underachievement and failure of start up performance to the use of innovative process technology without appreciating and managing technical risk. Factors contributing to technical risk include inadequate pilot plant testing, scaled up prototype equipment without backup, design flaws and poorly understood complex process chemistry."

Jan 1, 2009

By Carl Lubbe, Ron Frye

Numerous articles have been written regarding the effects of blast control plugs in an attempt to quantify stemming ejection rates, air overpressures, fragmentation’and other parameters measured using these devices. In an effort to further attempt to understand the function of these devices, field and laboratory research conducted with various stemming devices was performed to enhance existing data sets and analyze otherphenomena that occur when these products are used.

Jan 1, 1998

By John A. Cherry

Groundwater monitoring conducted at an acidic uranium-tailings impoundment in Wyoming and at one in Ontario indicate that at these unlined impoundments situated on unconfined sand aquifers, there exist well-developed plumes of contaminated groundwater. In the literature similar results are reported for three other unconfined aquifers at mill sites in Wyoming. The plumes extend for distances of several hundred to a few thousand metres from the impoundments. They have a zone of low pH beneath and adjacent to the impoundments and a larger zone of near-neutral pH that extends to the outer limits of the plume. The low-pH zones are generally small compared to the neutral-pH zones because the advance rate of the fronts of acidic tailings-derived water is slower than the average velocity of groundwater which controls the advance of the high pH zone. The retardation of the acid fronts is a result of geochemical reactions that cause hydrogen-ion consumption in a slowly-advancing neutralization zone. Within each of the plumes, the low-pH zone has high concentrations of transition metals, heavy metals and radionuclides. In the neutral-pH zones all of the metals and radionuclides occur at significantly lower concentrations and are generally at levels much below those specified in national drinking water standards. An exception at two of the Wyoming sites is uranium, which exists at levels close to the drinking water limit. A second exception is ferrous iron at the Ontario site, which occurs at high concentrations throughout most of the plume. The carbonate alkalinity at this site is much lower than at the Wyoming sites. The field data indicate that even in very permeable aquifers with a low content of silt and clay, there is normally a considerable capacity for acid-front retardation. To take advantage of this capacity to control contaminant movement in the design, operation and decommissioning of tailings impoundments, it is necessary to be able to predict the rate of acid-front movement. This predictive task has two primary components. The first is to identify the important flow paths from the tailings through the groundwater system and the second is to determine the degree of acid-front retardation that will occur as the tailings-derived water moves along these flow paths. Relative to these two tasks determination of the effects of hydrodynamic dispersion is generally of lesser importance and simple approximations that do not involve field or laboratory tests are probably adequate. In order to effectively apply the acid neutralization concept to the prediction of subsurface contaminant migration at uranium-mill tailings, improved representations of hydrogeochemical behavior of iron and aluminum in the neutralization zone and of the consumption of hydrogen ions through reactions with carbonate and aluminum-silicate minerals are required. Along with the hydrogen ions contained in the tailings water the ferrous iron represents a large potential source of acid but the extent to which ferrous iron converts to ferric iron to produce acid is problematic. Detailed hydrogeochemical evaluation of existing contaminant plumes and the performance of laboratory experiments under appropriate redox conditions ore prerequisites for the improvement of predictive models. However, the existing field and laboratory data provide a basis for preliminary predictions of contaminant migration from acidic uranium tailings impoundments.

Jan 1, 1982

By Felix Wolters, Michael Schütt

In over 40 years of operation, engineers at Aluminium Oxid Stade GmbH (AOS) have acquired a lot of experience whereby they have developed a series of optimizations regarding the specific primary energy consumption. The tube digester technology, invented by VAW in Germany and applied on an industrial scale for the first time in Stade, was brought to perfection by its innovative cleaning methods, which led to a constantly high heat transfer, low pressure loss and excellent availability of the digesters. Further improvements such as the heat recovery from the exhaust gas stream of the salt heater as well as the optimization of one of the fluid bed calciners and the installation of a combined heat and power generator (CHP) led AOS to where it is now—a leading alumina refinery with regard to the lowest energy consumption per ton of alumina.

Mar 1, 2017

By H. M. Park

Risk is a major factor in all mining activities, arising from many internal and external variables. The authors? research has resulted in a systematic method for the quantification of risk in mining projects (Park, 2012), and this research is being presented in a series of papers. The first paper (Park and Nelson, 2013a) identified the variables associated with risk in mining projects, and their effects and was published in the October issue of Mining Engineering magazine. The second (Park and Nelson, 2013b) discussed methods of assessing the overall risk associated with those variables (published at www.me.smenet.org), and presented a statistical model based on a survey of 31 experts. This paper will present an evaluation of the statistical model, using data from previous mining investment decisions in which the authors have been involved.

Oct 1, 2013

By Tilley J. L, Chicu D

The development of the Yallourn East Field brown coal open cut has involved the adoption of novel investigational programs into coal qual- ity. For example, weighted average coal property statistics for key proper- ties are determined by using a unique blend of traditional and 3-dimensional geostatistical estimation. Predicted property values are made freely available from the mainframe computer in the form of kriged esti- mates of 60 000 tonne coal blocks. Geostatistical predictions are being incorporated within the Mincom/Intergraph CADD system which is used for mine design. Key properties relating to coal type, moisture, and ash have been evalu- ated to provide the required data for the design and operation of both the open cut and the power stations as well as the briquette plant.

Jan 1, 1989

By Lluis F. Fontboté

The paper point out the deposits about the carbonate-hosted San Gregorio Colquijirca, as products of an epithermal high sulfidation system. Field, geochemical, and geochronological evidences suggest that the different ore types of the Colquijirca District are caused by a pulsed high sulfidation system subsequent to the emplacement of a diatreme volcanic complex. The first stage formed disseminated Au±Ag mineralization in areas affected by vuggy quartz alteration at Marcapunta. During a second stage, base metal mineralization replaced Eocene carbonate sediments from the Marcapunta diatreme to 2.5 km more to the north. San Gregorio and Colquijirca are to our knowledge the first "carbonate-hosted epithermal Zn-Pb high sulfidation deposit" recognized as such. The correct recognition of this ore type opens new exploration possibilities for base metal in high sulfidation systems affecting carbonate rocks.

Apr 24, 2001

By R Williams, M Baxter, D Zink, R Cunningham

The purpose of this paper is to discuss the efficient operation of a tailings dewatering circuit comprising a thickener and filter press through proper control and automation. It is common to see thickeners and filter press circuits each with their own control systems. This can cause multiple issues when trying to increase efficiency and reliability of the tailings management process. By automating the thickener and filter press controls, you are eliminating any delays and inconsistencies caused by human error and process variations. When done properly the system can maintain a consistent product as the feed characteristics change. Previously, operators would have to monitor the process parameters and adjust the system accordingly. This can now be accomplished using state of the art process control equipment that continuously monitors and adjusts critical variables using Programmable Logic Controllers (PLC) and Proportional Integral Derivative (PID) loops. The paper will detail the control theory used to maintain these systems, highlight other benefits of having a fully integrated plant such as predictive maintenance and remote diagnostics as well as present examples of how these have been implemented in field examples.CITATION:Baxter, M, Cunningham, R, Williams, R and Zink, D, 2018. Tailings process optimisation through automation and controls integration, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 416–421 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By A. S. Appleton, M. B. Bever, G. E. Dieter

A gold-silver alloy was deformed by explosive loading at shock pressures up to 510 kbars. The stored energy and hardness increased over the whole range of pressures; the largest rates of increase were observed between 120 and 150 kbars. In this range, markings rkavacteristic of defornation twins first appeared; higher pressures produced markings in all grains. These effects are compared with those of conventional deformation processes and are discussed in relation to probable structural changes. In recent years, increasing efforts have been devoted to the investigation of the effects produced in metals by the passage of high-intensity shock waves of explosive origin. By properly utilizing the energy released by the detonation of a high explosive, it is possible to generate pressure pulses of the order of 500 kbars and higher. (One kbar equals l0 9 dynes per sq cm or approximately 1000 atm.) The passage of a shock wave through a metal occurs at pressures which are very much greater than the yield strength. As the shock front passes a point in the metal, the pressure rises almost instantaneously, and continues to act at the point for a few microseconds. Thus, metals subjected to explosive shock loading experience a nearly instantaneous increase in pressure, and a subsequent release of pressure, which is almost as rapid. Under these conditions mechanical twinning and shear transformations occur readily. smith1 has investigated the metallurgical changes in copper and iron resulting from exposure to explosive shock waves. He found an appreciable increase in hardness in both metals. In copper, a hardness greater than that resulting from 95 pct reduction in thickness by rolling was obtained, yet in the explosive deformation, the thickness of the specimen decreased only a few percent. After explosive loading, the micro-structure of copper showed markings characteristic of mechanical twins. The amount of stored energy resulting from explosive loading is of interest. Measurements of the stored energy of cold work as a function of strain, temperature, strain rate, and composition have been made with gold-silyer alloys deforyed by rolling, orthogonal cutting,3 drilling,4 filing, wire drawing, and torsion. The investigation reported here was also carried out with a gold-silver alloy and its results can be compared with those for the deformation of this alloy by more conventional methods. EXPERIMENTAL PROCEDURES An alloy containing 82.6 wt pct Au and 17.4 pct Ag was purchased in several batches from Handy and Harman Co., New York, as annealed rod 1/4 in. dim. The rod was cold-rolled to a sheet approximately

Jan 1, 1962

By R. Q. Phillips

INTRODUCTION Since Canada commenced sulphur exports in the early 1960's, the volume of exports has grown steadily and by 1984 Canadian sulphur accounted for 45% of internationally traded sulphur. In 1984 a total of 7.6 million tonnes of Canadian sulphur was shipped to offshore markets and the U.S.A. Total shipments, including domestic sales, were 8.3 million tonnes. With a production of some 5.6 million tonnes, inventory was drawn down by nearly 3 million tonnes in order to keep pace with demand. Since 1979, world consumption has exceeded total world production and Canadian sulphur inventory has played a truly crucial role in balancing world supply and demand. Consequently, by the end of 1984 the Canadian inventory, which stood at 21 million tonnes in 1978, had been almost halved to 12 million tonnes. This inventory, however, is still by far the largest in the world and will continue to play a vital role in the world supply until expected depletion around 1990. Canada is the world's second largest producer of sulphur following the U.S.A.. The Current production level of between 5 and 6 million tonnes per annum is forecast to be maintained to 1990 with only a marginal fall in that production level in the following decade to the year 2000. This will ensure that Canada retains its position as one of the largest producers and most important suppliers of sulphur in the world market well into the future. CANADA AS WORLD SUPPLIER OF SULPHUR Since Canada commenced sulphur exports in the early 19601s, exports have grown steadily. (Figure 1) The rate of growth accelerated in recent years and in 1984 a total of 7.6 million tonnes was sold for export, compared to 3.0 million tonnes in 1975 and less than 1 million tonnes in 1964. World trade in sulphur also increased during this period, from 11 million tonnes in 1975 to 17.0 million tonnes in 1984 (Figure 2). Most of this increase in volume was accounted for by Canada and Poland. As a result, the importance of Canada as world supplier expanded from 28% in 1975 to 45% in 1984. The markets for Canadian sulphur can be divided into two broad categories, i.e., solid and liquid (Figure 3). The solid market is the largest, taking about 70% of Canadian output, virtually all of which is sold offshore. The U.S.A. and the Canadian domestic market take about 20% and 10% respectively, in liquid form. In 1984, (figure 4) total Canadian sulphur sales exceeded 8 million tonnes with offshore export sales at a record 5.8 million tonnes and sales to the U.S. of 1.8 million tonnes. Domestic sales accounted for only 0.7 million tonnes. The general trend for offshore export sales has been upward whereas there has been relative stability in domestic sales. The exceptional growth in offshore sales in the 1970's necessitated considerable capital investments by the industry in order to establish a logistics system capable of handling increasing offshore tonnages. Over 50 sulphur plants are currently operating in Alberta and British Columbia. Some of these are connected by rail, (Figure 5) the balance being generally connected by road. There are currently fourteen of the larger rail-connected plants designated as export plants, and these are equipped with sulphur forming facilities. The long distances between these plants and tidewater terminals in Vancouver is a very significant factor in complex logistics of Canadian offshore sulphur exports (Figure 6). Alberta and B.C. plants are located an average of 1,400 kilometers from tidewater.

Jan 1, 1986

By André Luis de Oliveira

O Alto Forno 3 (AF3) da Companhia Siderúrgica Nacional (CSN) é o equipamento muito importante no processo siderúrgico da Usina Presidente Vargas (UPV), situada em Volta Redonda (RJ), por responder por mais de 70% da produção de gusa da UPV. Na produção de gusa é gerado o Gás de Alto Forno (GAF), subproduto de alta relevância, pois este gás sai do topo do AF3 com grande pressão e cinética, energia essa passível de utilização. Em 2007 a CSN, optou por adquirir um equipamento denominado “Top Pressure Recovery Turbine” (TRT), capaz de aproveitar tal energia para gerar energia elétrica. Em 2013, a equipe de supervisores da KHI – Kawasaki Heavy Industrie, fabricante da turbina, veio para o Brasil para realizar no equipamento os testes a frio e a quente para na seqüência vir a operá-lo. Ocorre que fatores alheios ao objetivo desta apresentação impediram a equipe da KHI de partir o equipamento no tempo previsto, bem como de retornar ao Brasil para dar seqüência nas atividades. Em novembro de 2013 a CSN definiu por partir o equipamento com recursos próprios, sendo este o foco do trabalho. A presente contribuição técnica vem mostrar o trabalho desenvolvido internamente pelo grupo técnico a fim de finalizar o projeto e colocar a Turbina de Topo (TRT) em operação, fato este dado total ênfase pela direção da empresa devido ao cenário nacional de crise energética em que os valores de energia estavam no limite máximo permitido pela legislação e impactando diretamente nos custos da empresa.

Sep 25, 2017

By Y. Yu

Florida phosphates ore typically processed by reverse flotation with an intermediate acid-scrubbing step. A single-reagent flotation process, using fatty acids or amines as the collector, would eliminate the intermediate scrubbing step plus an additional flotation step. This would not only simplify the process flowsheet but would also result in reduced reagent costs. The potential of single-reagent flotation of Florida phosphates using fatty acids as the collector is examined in this study. Introduction The beneficiation scheme now used for Florida phosphates involves the following three steps (Smith, 1976: Lawyer et al.. 1978, 1984: Moudgil et al, 1976, 1979, 1986, 1987): •rougher flotation of fluorapatitc particles using a fatty acid-fuel oil mixture as the collector. •scrubbing of fatty acid, and •cleaner flotation of silica particles using amine collector. Several attempts have been made to simplify the process flowsheet by floating either apatite or silica (not both, as is the current practice). However, single-reagent flotation schemes have had limitations in meting the concentrate-grade requirements of the phosphoric acid plants. In this study, an attempt was made to use a minimal amount of the fatty acid-fuel oil collector to obtain an acceptable grade (rougher) concentrate. Invariably, the recovery in such cases is expected to be lower than in the conventional rougher-flotation step. Therefore, scavenger flotation of tailings with additional fatty-acid collector was conducted to improve the phosphate recoveries.

Jan 1, 1997