Search Documents

Significant advances have been made in the design of centrifugal slurry pumps that are used for pumping high-density viscous and paste slurries. This paper presents the results of a series of centrifugal pump performance tests that were conducted using an FLSmidth 6 x 4 Krebs millMAX centrifugal pump. The pump was fitted with a dry mechanical seal to prevent dilution of the slurry from gland service water, as the theology of the slurry is sensitive to small changes in slurry density. Tests were done using paste kaolin slurry with Bingham yield stress values between 578-1 120 Pa and plastic viscosities between 728 and 1491 mPa.s. The viscous properties of the paste during each pump test were measured using a rotational viscometer. Pump head and efficiency de-rating were measured and compared to the correlations of Walker and Goulas (1984). The test data shows the pump's best-efficiency point (BEP) changes and shifts to the left of the performance curve. The pump efficiency decreases as the slurry yield stress increases. The head de-rating data shows more head de-rating at the low flow rates compared to the high flow rates for the high viscosity slurry, which is in line with the findings of Walker and Goulas (1984). This paper demonstrates that it is possible to pump very viscous, high yield stress slurries with limited head and efficiency de-rating using centrifugal pumps, provided that positive suction conditions are maintained at all times.

Jan 1, 2012

By E. D. Kindle

"The Duthie mine is on the southwest slope of Hudson Bay mountain 7 1/2 miles west of Smithers, British Columbia. A good motor road about 15 miles long connects the mine with the Canadian National railway at Smithers. The principal workings are on the Henderson group of claims between elevations of 3,200 and 4,000 feet above sea-level. Silver, lead, and zinc were produced from this mine between 1924 and 1930.Three adit drifts known as the Compressor, McPherson, and Thompson levels were driven along the Henderson vein-lode in 1922, and the following year the operating company, known as Duthie Mines, Limited, shipped some high-grade silver-lead-zinc ore. Further shipments of high-grade, handsorted ore were made in 1926, and in 1927 a modern flotation-type mill was built, having a capacity of 50 tons of ore a day. Mining operations were suspended in March 1930."

Jan 1, 1954

By Rogerson R, Queen L

The petrology and age of mid Cretaceous to Palaeogene marine volcanics may provide important clues to the palaeogeography of the period, particularly for tectonic elements and events outboard of the Papuan Basin. This initial survey of known marine volcanics of this age reveals a paucity of reliable data on isotopic ages, geochemistry and syngenetic mineralisation on virtually all units. Existing data allows a tentative subdivision of known marine volcanics into either MORB-like early Palaeogene rifts/ marginal basins, early Palaeogene ensimatic arc rocks overlying ?Late Cretaceous and Palaeogene fore-arc/marginal basin crust, late Palaeogene ensimatic arc rocks, and mid to Late Cretaceous ensialic rift rocks. Due to lack of data, some units are difficult to classify into these categories.

Jan 1, 1991

By I. Iwasaki

A low-grade copper-nickel deposit, with an estimated size of 4.6 billion tonnes and with average analyses of 0.6% copper, 0.2% nickel, occurs in northeastern Minnesota. In addition to copper, nickel, cobalt, and precious metals, the Duluth gabbro contains magnetite, ilmenite, olivine, plagioclase and biotite. It is estimated that the flotation tailings that would be produced by a concentrator of optimal size to sustain a smelter would amount to 20 million t per year. The flotation tailings, having already been ground, warrant a closer examination for the recovery and utilization of potential by-products. The residual sulfide minerals and fibrous minerals may also be isolated and treated separately for useful purposes or for disposal in an environmentally acceptable manner. Two flowsheets were developed; one involving preconcentration by low- and high-intensity magnetic separation and another involving preconcentration by gravity concentration. The concentration methods for recovering and purifying individual by-product minerals were investigated. From their chemical, physical and mineralogical characteristics, the potential areas of application and marketabilities of each product fraction were surveyed.

Jan 1, 1983

By L. M. Guayacán-Carrillo, G. Armand, A. Noiret, D. Seyedi, S. Ghabezloo, J. Sulem

"The main purpose of this paper is to analyze the convergence measurements in a drift excavated in the Callovo-Oxfordian claystone. The drift axis is in the direction of the major principal horizontal stress whereas the stress state is quasi-isotropic in the drift’s section. The initial geometry of the drift being circular, the anisotropic character of the deformation is taken into account by assuming that the drift shape evolves in an elliptical shape. The convergence measurement data on six different points around the drift are analyzed to identify the main axes of the deformation ellipse, following the methodology proposed by Vu et al. (2013, Rock Mech Rock Eng, 46, 231-246). Then, using the semi-empirical law proposed by Sulem et al. (1987, Int J Rock Mech Min Sci, 24, 145–154), the convergence evolution is fitted independently for each axis of the ellipse. This method permits to distinguish two effects: the face advance effect and the time-dependent behavior of the ground. The results for the two directions of the ellipse axes show very close values for the parameters describing the time-dependent properties of the ground, the distance of influence of the face, and the extension of the decompressed zone around the gallery. Such model can provide valuable insights for predictions of the convergence evolution in the long-term. INTRODUCTIONDeep disposal of radioactive waste has been studied in France for more than two decades. The French National Radioactive Waste Management Agency (Andra) began in 2000 the construction of an Underground Research Laboratory (URL) with the main goal of demonstrating the feasibility of a geological repository in Callovo-Oxfordian claystone. Several research programs have taken place to improve the knowledge of the rock properties and its response to the excavation progress. The optimization of supports design for long-term behavior is an important point to develop. A network of experimental drifts has been constructed with variations on: excavation method, structure geometry, supports system and orientations with respect to in-situ principal stresses’ directions. In each drift different sections have been instrumented to monitor the convergence evolution and the rock deformation. Continuous monitoring of the excavated zone around the drifts revealed the development of a fractured zone (extensional and shear fractures) induced by the excavation. The extent of this fractured zone depends on both the drift orientation and the in-situ stress field (Armand et al., 2014). Indeed, the fractures distribution has an important influence on the convergence of the drifts."

Jan 1, 2015

By Kausik M. Sinha

Hydraulic stowing, which is being practiced in several major coal producing countries to deal with adverse mining conditions, usually permits almost 100% coal recovery from underground mines with minimal and controlled surface subsidence. It can be implemented in the US coal mines to reduce the severe effect of land subsidence and at the same time improve the cost of coal production, both of which are major setbacks for the coal industry in the USA

Jan 1, 1989

By M Rafty, A Markham, S Atkinson

Australia contains some of the most productive mining areas and is characterised by ancient landscapes and highly variable hydrology. Historical mining of iron ore, coal and other minerals has targeted ore deposits located above water tables, and elevated above creek lines where possible to reduce cost. The downturn in mining caused by falling ore prices over recent years has triggered a drive to reduce cost, maximise yield and delay capital expenditure associated with opening new mines. So as the ore deposits with more favorable mining conditions become depleted there is an increased focus on mining ore associated with valley floors and creek lines. This is demonstrated by a regional assessment of the extent of Channel Iron Deposits (CID) and Iron Ore (Fe) Mines and Deposits in the Pilbara Region of Western Australia (Figure 1). A large proportion of these mines are, or plan to, target high grade CID ore associated with existing creek systems. Figure 2 shows outcropping and inferred sub-cropping CID extents, which suggests there are vast quantities of CID ore deposits throughout the Pilbara Region, intersected by major creeks which could be mined at some point in the future using creek diversions (Atkinson et al., 2017). A similar picture could also be produced for coal mining in Queensland, particularly in areas such as the Bowen Basin.While creek diversions provide an opportunity to maximise the utilisation of these orebodies and extend the life of mine, creek diversions can involve substantial financial, social, environmental and regulatory risks that need to be carefully managed (Markham et al., 2017, Atkinson et al., 2017). This paper discusses the key issues and opportunities associated with diversion decision making. It highlights the importance of using a well-structured assessment methodology that allows key stakeholders to be part of the assessment process and is complementary to material presented in Atkinson et al., (2017). Design considerations for operational and closure designs are presented, as well as mine planning considerations, risks, cost saving opportunities and the benefits of an integrated approach to design. The role technology plays in diversion design and performance monitoring is discussed as are the potential opportunities for the future.CITATION:Atkinson, S, Markham, A and Rafty, M, 2018. Diversion decision making with an integrated approach to design for operations and mine closure, in Proceedings Life-of-Mine 2018, pp 74–79 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By Alexander L. Field

IN a previous paper,' the experimental methods used and some of the results obtained in an extensive investigation of steels containing zirconium were described. The present paper considers in greater detail one of the most interesting of these effects, namely, the elimination of " red shortness" and the occurrence in steel of a compound of zirconium and sulfur. A consideration of the actual percentages of zirconium, manganese, and sulfur in numerous steels in the light of behavior during rolling has led to new conclusions of the most practical import regarding the reciprocal relationships of these elements. The microscopic examination of high-sulfur steels containing zirconium has also been productive of interesting results. Before discussing the experimental data in question, it may be stated, briefly, that the rettetion between zirconium and sulfur in molten steel may be represented by the simple equation, Zr + 25 = ZrS², and that the zirconium sulfide thus formed occurs in the finished steel in the form of gray-colored inclusions, closely resembling manganese sulfide and, like the latter, exhibiting plasticity at rolling temperatures. Molten steel containing zirconium retains such a negligibly small amount of oxygen in solution that the foregoing reaction goes to completion. Hot-rolling Properties of High-sulfur Steels with and without Zirconium The chemical composition of twenty-eight steel ingots embracing eleven heats made in a basic-lined electric furnace is shown in Table 1. The practice followed in the manufacture of these high-sulfur steels was described in the previous paper. Table 1 also gives the behavior of the

Jan 1, 1924

The exploration industry generally has a low opinion of the quality of the service supplied to it by government departments. In particular, the academic research-related emphasis of the Bureau of Mineral Resources (BMR) and the relatively low level of explora- tion assistance offered by several Mines Departments are of concern. In a number of areas of geoscience research, the industry perceives a mixup of priorities and a lack of understanding on the part of governments as to its needs. While government's sights are, and should be, set on the future needs of the community at large, the industry doubts that government budget allocations to the BMR and Mines Departments are either large enough or being cost-effectively spent. This is certainly the case for such areas as exploration assist- ance, provision of basic exploration data, and applied geoscientific research. On balance, the exploration industry's perceptions are misguided in a number of respects because of a lack of communication with government. However, this reinforces the need for changes in the manner in which govern- ment departments communicate with industry and, in particular, the criteria upon which research priorities are based. At a time of contracting oil and mineral exploration expenditure, and near-record levels of geoscientist unemployment, the government's role is critical and should be open to question.

Jan 1, 1986

By D. G., Bosse&apos

Equipment choices for ultrafine grinding encompass several different types of dry and wet size-reduction devices. These need to be put into functional perspective for systematic analysis of capabilities and limitations versus processing requirements of the materials to be satisfactorily ground. Particle strengths plus maximum and average sizes are the primary variables controlling grinding action requirements and equipment options for efficient processing. These are fairly well understood and provide the starting point for decisions. Particle space requirements under dynamic processing conditions vary with particle shapes and size-distributions by as much as 30X. This additional major variable is not widely appreciated and does need adequate description to provide a firm basis for selecting processing compositions and procedures.

Jan 1, 1983

By Benjamin C. Craft, Frank Perkins

The wall-building properties of salt-water muds can be maintained at high temperatures by additions of gum karaya, gum ghatti, gelatinized starch, or commercially prepared starch. A germicide should be used to prevent fermentation. Introduction The behavior of drilling mud has received special attention from the petroleum industry within the past few years in numerous research projects dealing with such subjects as chemical treatment, gelation, and filtration characteristics. The importance and control of filtration, or water loss, is readily apparent* It affects the analysis of side-wall cores and interpretation of electric logs; it controls to a large extent the work of primary cementing, reduces the amount of expensive fishing, and permits the running of long strings of casing. It has been found that among the many factors that have an adverse effect on filtration, the presence of electrolytes, in general, and of salt, in particular, is outstanding. The effect is one of flocculation of the colloids due to neutralization of the negative charges on the clay particles. This reaction is further increased on the Gulf Coast because high temperatures reduce dispersion, to a minimum, causing increased flocculation in both fresh-water and saltwater muds. The problem of reducing water loss in salt-water muds by the addition of gums and starch at atmospheric temperature has been investigated,' and many successful field tests in West Texas indicate its solution. From the work of Byck2 it is concluded that no existing method will permit an approximate determination of the filtration rate at high temperatures from data taken at room temperatures. Filtration should be measured at the ternperature actually anticipated in the well, or at least at a number of lower temperatures and extrapolated over a small range. A laboratory study has been made of the chemicals available for the filtration characteristics of salt-water muds at high temperatures, and the use of germicides to prevent fermentation. Laboratory Investigations Procedure Since the purpose of this investigation was to compare several different gums and starches at elevated temperatures, mud from the same source was used for all the tests. Viscosity was measured in a Stormer viscosimeter at 600 r.p.m. and water loss was determined with a Baroid High-pressure and High-temperature Wall-building Tester3 at temperatures from 80' to 250°F. and at a pressure of 500 lb. per sq. in. for 30 minutes. The samples tested consisted of 150 grams of commercial Louisiana mud, 50

Jan 1, 1943

By Benjamin C. Craft, Frank Perkins

The wall-building properties of salt-water muds can be maintained at high temperatures by additions of gum karaya, gum ghatti, gelatinized starch, or commercially prepared starch. A germicide should be used to prevent fermentation. Introduction The behavior of drilling mud has received special attention from the petroleum industry within the past few years in numerous research projects dealing with such subjects as chemical treatment, gelation, and filtration characteristics. The importance and control of filtration, or water loss, is readily apparent* It affects the analysis of side-wall cores and interpretation of electric logs; it controls to a large extent the work of primary cementing, reduces the amount of expensive fishing, and permits the running of long strings of casing. It has been found that among the many factors that have an adverse effect on filtration, the presence of electrolytes, in general, and of salt, in particular, is outstanding. The effect is one of flocculation of the colloids due to neutralization of the negative charges on the clay particles. This reaction is further increased on the Gulf Coast because high temperatures reduce dispersion, to a minimum, causing increased flocculation in both fresh-water and saltwater muds. The problem of reducing water loss in salt-water muds by the addition of gums and starch at atmospheric temperature has been investigated,' and many successful field tests in West Texas indicate its solution. From the work of Byck2 it is concluded that no existing method will permit an approximate determination of the filtration rate at high temperatures from data taken at room temperatures. Filtration should be measured at the ternperature actually anticipated in the well, or at least at a number of lower temperatures and extrapolated over a small range. A laboratory study has been made of the chemicals available for the filtration characteristics of salt-water muds at high temperatures, and the use of germicides to prevent fermentation. Laboratory Investigations Procedure Since the purpose of this investigation was to compare several different gums and starches at elevated temperatures, mud from the same source was used for all the tests. Viscosity was measured in a Stormer viscosimeter at 600 r.p.m. and water loss was determined with a Baroid High-pressure and High-temperature Wall-building Tester3 at temperatures from 80' to 250°F. and at a pressure of 500 lb. per sq. in. for 30 minutes. The samples tested consisted of 150 grams of commercial Louisiana mud, 50

Jan 1, 1943

By D. R. Brooks

The Bureau of Mines has tested a dewatering technique for phosphatic clay waste. The technique utilizes a flocculant, polyethylene oxide (PEO), that forms strong, stable flocs that can be dewatered on a static screen followed by further dewatering on a rotary screen or trommel. In field tests conducted in central Florida, clay wastes containing approximately 4 pct solids have been consolidated to greater than 20 pct solids. The rate at which PEO-treated material continues to dewater in a mine cut also was monitored. Preliminary results indicate that PEO-treated material will dewater to 30 pct solids in 80 days. Pretreatment of phosphatic clay waste with lime lowers the PEO dosage required for dewatering.

Jan 1, 1986

By D. E. Munson, H. J. Sutherland

Empirical methods for describing the shape of the subsidence trough over coal mines in Europe are tested against field measurements of subsidence over longwall panels in the United States. The graphical methods developed by the National Coal Board in the United Kingdom do not correlate well with the U.S. measurements; however, the profile functions typically used on the Continent give quite acceptable fits to the data. In the case of two longwall panels mined at Old Ben No. 24 in Illinois, a trigonometric profile function appears the best choice; in the case of two longwall panels mined at York Canyon in New Mexico, an error integral function is somewhat superior. Analyses of subsidence development curves show that rate effects occur. A comparison of fitting parameters establish influence functions as an important methodology for future analysis. In conjunction with the evaluation of empirical methods, an analytic model based on material failure and bulking was developed. A key element of the model is the void-volume distribution function which establishes a mechanism for transfer of significant amounts of the mined volume to the surface. Preliminary calculations demonstrate the features of the model and illustrate close correlation to physical observations in the field. Moreover, centrifuge models simulating the subsidence process have been used successfully to demonstrate the dominant or key failure modes necessary to the analytic model. General features of the centrifuge simulations and model calculations correlate well.

Jan 1, 1982

By T. A. Lang

For permanent structure underground, where rock is not competent, support usually consists of concrete or reinforced concrete. However, temporary supports in the form of timber or steel are often needed during construc-tion. Although the history of rock bolting is relatively short—50 years— their use has become widespread in general engineering construction as well as mining. This profusely illustrated and detailed study covers a broad range in the field of rock belting: from the behavior of rock and bolts including rock properties, masses, and structure; mathematical formulae for rock bolt applications; through analysis of various operations and descriptions of the bolts themselves. Rock construction is one of the oldest of the engineering arts and its origin is lost in antiquity. From the days when early man decided that he wanted to improve the natural caves which he was using for shelter and protection or made a river crossing by placing rocks to form a ford or causeway, we have had structures made of rock. It is not too much to say that rock in situ as a structural material forms part of every major engineering undertaking. Rock bolting is one means whereby the inherently good characteristics of rock in situ are preserved and used to the best advantage and the bad characteristics ameliorated. In many cases the latter are accentuated by construction processes used. Rock bolting, as with other rock construction techniques, is only just beginning to emerge from being an art. Consequently, its theory and practice is still more descriptive than mathematical. ROCK BOLTING In underground excavations, where the rock is not competent, support is provided. For the permanent structure, this generally consists of concrete or reinforced concrete. However, support may be needed during construction before the concrete can be placed, and conventionally this consists of timber or steel support in the form of ribs, struts, and lagging. Alternatively, rock bolts may be used. Although their use dates back over 50 years, it is only in recent years that rock bolts have become widely used, not only in mining but in general engineering construction. A rock bolt is a steel bar which is inserted in a hole drilled in rock. The end away from the rock face has a device which permits it to be firmly an- chored in the hole and the projecting end is fitted with a plate which bears against the rock surface. The bolt is placed in tension between the anchor and the plate, thereby exerting a compressive force on the rock. The essential feature of a rock bolt is that it is placed in tension. This distinguishes it from anchor bars which are grouted into holes in rock, but which are not prestressed. The difference between an anchor bar and a rock bolt when the rock bolt is grouted in is analogous to the difference between the reinforcement in ordinary reinforced concrete and in prestressed reinforced concrete. The view that rock bolts only pin or nail blocks or slabs of rock which are loose to the sounder rock behind them is erroneous. Rock bolts are useful for this purpose and have been so used for a long time. However, the term rock bolting, as used here, means the designed use of rock bolts to reinforce and develop the rock around an excavation into a structural entity which can competently play its part in a structure such as a powerhouse or a mine installation. Rock bolts behave quite differently than steel ribs. They can be installed at the working face directly after blasting and within a short space of time can be exerting a stabilizing pressure on the loosened rock surface. This early installation not only partially restores loosened blocks of rock to their original unloosened positions, but also it prevents the gradual relaxation or loosening of the decompression zone behind the new rock face. In contrast, steel ribs generally use timber blocks, wedges, and lagging between the ribs and the irregular rock surface. The timber is relatively compressible, and loosened blocks of rock must move outwards an appreciable distance before any load builds up on the steel ribs. Also, the ribs may settle as the foot blocks and foundation become compressed. Hence, it may take several days or weeks before the rock has moved sufficiently to make the steel ribs carry an effective load.

Jan 1, 1961

In July 1994 the Premier, John Fahey MP, announced that the New South Wales Government would make available a total of $40 million over six years in new funding for the Department of Mineral Resources. These funds are to be applied directly to the generation of regional geological and geophysical information. The Government's initiative known as `Discovery 2000', is aimed at providing a major boost to the exploration industry. The Government expects new discoveries to be made and new mines to be developed because of the initiative and, perhaps, the first ever commercial oil or gas production in New South Wales. The Government's return will come from increased economic activity, and from the increased royalty return from higher levels of production. Quality information is the key to successful exploration. In the highly competitive business of mineral and petroleum exploration high quality regional geological and geophysical information improve both the efficiency and effectiveness of the area selection or project generation process. Using the `needle in the hay stack' analogy, Discovery 2000 will vastly improve industry's chances of finding the haystacks. It is up to the mineral and petroleum industries to find their respective `needles'. Careful target area selection is probably the most critical factor in mineral exploration. The ability to select the most prospective areas, or to identify prospectivity that others have failed to recognise, can make all the difference between success and failure. Government geological surveys clearly have a crucial role to play in providing the geoscientific information infrastructure that companies must have if they are to make the discoveries this country needs to pay its way in the world. It is the regional information generated by Governments that sets the scene for efficient exploration. This regional information includes regional aeromagnetics and radiometrics and gravity, regional geological mapping and tectonic analysis, and geoscientific databases. The New South Wales Department of Mineral Resources (by various names) has been providing such information for over 100 years and has led the way in many aspects of the generation and dissemination of geological, geophysical and metallogenic Information.

Jan 1, 1995

By A. W. Furbank

IN reviewing the aerial cameras produced in different countries, it becomes apparent that in nearly all of them an attempt has been made to secure the greatest possible angle of view. This angle, of course, is determined by the objective. The objectives most commonly in use in aerial cameras have a maximum angle of 65º. The objective developed for this new Zeiss camera combines freedom from distortion and brilliant definition, with an angle of 95º. Aerial mapping, it is claimed, has been placed on a different economic basis, and new possibilities presented, particularly in connection with automatic stereoscopic plotting instruments, to which some short references are made. One way of enlarging the angle of view is to couple several instruments with their axes convergent, thereby producing a multilens camera. Typical of cameras of this sort in the United States is the Bagley four-lens camera, which later was developed into the five-lens camera (T3-A) of the U. S. Air Corps. More recently, in order to get away from the unfavorable Maltese cross image field of the five-lens camera, and to obtain a more practical form, two five-lens cameras were combined. By using them in tandem and rotating them by 45º relatively to each other, a ten-lens camera was produced, covering an octagonal ground area, with a total angle of view of 140º. Similar designs have been evolved in other countries. In all of them, however, a number of difficulties have arisen, quite apart from their large weight and high cost. Because of their complex mechanism, numerous shutters and magazines, and the high precision with which these parts must be interadjusted and synchronized, these cameras are far from dependable Moreover, a multilens camera by itself does not yet constitute a complete outfit for producing pictures suitable for photogrammetric survey. Because all the component pictures, except the central one, are obliques, it is always necessary to employ rectifying apparatus which transforms the marginal views to the perspective of the central one. In multilens cameras with many individual magazines, it is not convenient to

Jan 1, 1938

By Satu Jyrkönen

A single-particle laminar-flow technique was used to study oxidation of four synthetic nickel mattes, which were screened into three size fractions, Experimental conditions were: reaction gas from N2 - 21 to 75 vol-% O2; gas preheating temperatures ranging from 500 to I 100'C. The four mattes were synthesized so that Ni/Cu ratios of I and 10 were obtained with high and low iron contents. Chemical analysis of the particles was used to determine the oxidation degree of the materials, and optical and scanning electron microscopy were used to detect their morphology, internal composition and structure. The best sulfur removal from the synthetic nickel mattes was achieved under the most oxidizing conditions with the finest size fraction. The matte with Ni/Cu = 1 and high iron content was found to be most reactive. The least reactive matte was with Ni/Cu = 10 and low iron content; the coarse fraction particles did not react at all under the conditions studied.

Jan 1, 1996

By F. Ziaie

Line electrical resistivity method using physically infinite distance between current line electrodes is proposed to determine the location of mine workings. In this method at least three line electrodes are used. One of the current electrodes is used as a sinkhole electrode while the other two are used for different activiations of line electrodes when the survey area is between one of the line electrodes and outside the other one. The resistivity profiles perpendicular to the current line electrodes for different activation of electrodes is plotted versus the distance of the midpoint of the measuring potential electrodes. The anomaly due to presence of any locally lateral resistivity variation (e.g. mining cavity) will represent itself as peak or trough depending on resistivity contrast between the source of the anomaly and surrounding medium. Physical simulation of the proposed model was conducted by using a tank model in the laboratory. The results of experiments appear to be consistent with the theoretical model. Experiments for different depths and different spacial locations of the simulated cavities appeared to be successful for locating the depth and size of the cavity.

Jan 1, 1989

By John Ellenberger

The nature of a stone deposit is rarely defined through exploration and engineering design, but more through the actual experience encountered as the mine develops; hence, issues with ground control are often at the forefront for a new mine. Ground control problems account for over 15 percent of lost-time injuries in underground stone mines. The objective of this work is to present actions taken during early development of a stone mine to mitigate the obvious effects of high horizontal stress on ground control. The mine was developed from a box cut with relatively little cover, and high horizontal stresses were not anticipated. Early recognition of possible high horizontal stress resulted in mapping of the mine using the NIOSH-developed Roof Fall Risk Index (RFRI) to provide a baseline to objectively analyze roof conditions. A program of borescoping the mine roof provided valuable roof beam thickness data and found that the roof beam was of minimal thickness, approximately 10 percent of drift width. As the mine developed, it became apparent that ground control problems related to high horizontal stress existed. A concentrated effort was made to improve ground conditions by implemeting a number of mitigation techniques. Actions taken by the mine included systematic roof support, reorientation of mining direction, a lower roof horizon, reduced span widths and reduced mining height in crosscuts to prevent running falls. These strategies resulted in signifcantly improved ground stability.

Jan 1, 2012