Search Documents

By R. R. Klimpel

In three recent publications, Klimpel et al (1988) and Klimpel and Hansen (1988, 89), the theory and invention process behind the identification of two new classes of sulfide mineral collectors were summarized. These two new families can be represented by the 111 generalized formulate: R1-S-R1 -NRI III (denoted as the F-series chelation family) and R-S-R or R -CHSCH-R (denoted as the S-series redox family). The influence of systematic changes in the various R groupings on laboratory batch flotation cell tests has been covered in the above references and will not be repeated in this paper. In particular, the recent article by Klimpel and Hansen (1989) should be studied as a research introduction to this paper.

Jan 1, 1989

By J. M. W. Mackenzie

The interactions between oil drops and mineral surfaces have been examined for the cetyltrimethylammonium bromide (CTAB)-quartz and sodium dodecyl sulfate (SDS)-hematite systems. The results have been interpreted using a electrical double layer interaction model, a "sweeping-penetration" model based on steric interactions and a free energy of adhesion model. The adsorption of long-chain ions at the mineral interface was also studied and found to follow a Fuerstenau-Modi model of combined Coulombic and chain-chain interaction forces. The basis of the emulsion flotation process and the feature which makes it differ from conventional flotation is: encounter, followed by adhesion, between oil drops and mineral particles which are suspended in an aqueous environment. The manner in which the adhesion between these two phases contributes to the flotation process may be through the formation of min-eral-oil drop-mineral linkages, mineral-oil drop-air bubble linkages, or a combination of both. Possible flotation mechanisms derived from these adhesion processes are shown schematically in Fig. 2 while Fig. 1 shows an example of the first mechanism for quartz particles which have been floated using a cetyltrimethyl-ammonium bromide (CTAB)-Nujol emulsion as collector. In Fig. 2 the three phases, mineral, oil, and air, for convenience have been shown as having approximately equal size. This would not always be the case in an actual emulsion flotation operation. For the flotation of sand-sized particles of approximately 0.5 mm diam, the mineral particles would be at least ten times the size of the largest emulsion drops present in the system, while in the flotation of —10u slime particles, the mineral phase may be of the same order of size as the oil phase. The air bubbles in a flotation cell are normally about 1 to 2 mm in diam and therefore, in general, would be larger than the oil drops. Although the relative size of the three phases does not alter the basic adhesion processes between oil drops, mineral particles, and air bubbles, which depend on the physical and chemical properties of the interfaces involved rather than on the extent of these interfaces, it does alter the degree of deformation of the oil drops and air bubbles which will occur on adhesion. For mechanisms 1 and 2 to take place, the oil-water and mineral-water interfaces must be partially replaced by a mineral-oil interface while in mechanism 2 there is the additional requirement that the oil-water and air-water interfaces must be replaced by an oil-air interface. In view of the importance of the oil drop-mineral particle encounter and subsequent adhesion stages to both of the emulsion flotation mechanisms discussed, a study has been made of some physicochemical factors which control these processes for Nujol-cetytri-methylammonium bromide (CTAB)-quartz and Nujol-sodium dodecyl sulfate (SDS) -hematite systems. Experimental Electrokinetic Measurements.—The zeta potential of mineral particles was measured using a streaming potential technique similar to that described by Fuerste-nau.1 The streaming potential was measured using a multirange electrometer while the plug conductivity was measured using a 50 cycle sec1 bridge. Measurements were made on 28 x 65 mesh particles. Contact Angle Measurements.—A captive bubble technique was used to measure the contact angles for air bubbles and oil drops. The angles were measured on fracture faces of unmounted minerals which proved easier to clean than polished mounted specimens and should more closely represent a flotation system. Reagents: These have been described in a previous publication.0 Minerals: Rock crystal quartz from the New England district, N.S.W., was used for contact angle and streaming potential measurements. The quartz was hand

Jan 1, 1971

By G. W. Jones, I. Spolan

"INTRODUCTION The operation of internal-combustion engines at high altitudes and the general aspects of combustion processes in rarefied atmospheres have created considerable interest in the problem of ignition and flame propagation at low pressures. Nuckolls, Matson, and Dufour 4/ have published results on the effect of low pressures on the propagation of flame in gasoline vapor-air mixtures in vessels of large capacity. The volumes of their test equipment varied in capacity from 0.425 to 125 cubic feet. Various sources of ignition were employed. These authors found that the explosive range of gasoline vapor in air decreases with decreasing pressure at pressures considerably below atmospheric, until a limiting absolute pressure of about 33 mm. mercury at ordinary temperature is reached, at which point no appreciable flame is propagated.Experiments carried out at the Bureau with natural gas-air mixtures at reduced pressures have shown 5/ that the limits of inflammability are but little affected at reduced pressures down to 175 mm. mercury. As the pressures of natural gas-air mixtures are reduced below atmospheric, the mixtures become more difficult to ignite; however, if a suitable source of ignition is employed, the limits of inflammability are as wide at 175 mm. mercury absolute pressure as they are at atmospheric pressure. In view of these observations with natural gas-air mixtures, it appears important to investigate gasoline vapor-air mixtures for possible similar behavior. For this reason the tests herein described were carried-out."

Oct 1, 1946

By A. A. Collins

OF widespread interest to all lead metallurgists is a dross smelting process that will consistently give mattes and speiss of low lead and high copper contents. It is a problem that has intrigued operators through the years. In the past few years, with increased amounts of copper and overcrowded metallurgical furnaces, it has been almost imperative to evolve some method. Experience at El Paso has shown that high copper-to-lead ratios can be consistently attained by use of the new soda process. † Older Methods Three older methods, i.e., 1. Dross plus siliceous ore and limestone. 2. Dross plus one fourth blast-furnace speiss and siliceous ore, 3. Dross plus sulphides and siliceous ore and scrap iron, do not give consistent results and the products are higher in lead and lower in copper than those produced with the soda process. Any radical changes in the blast-furnace drosses will throw any of these older methods into a tailspin. For almost ten years, El Paso used the third method, with varying results. It was noted that as the arsenic and anti- mony contents of the dross increased, the speiss and matte steadily increased in lead and decreased in copper. A dross containing four parts of copper to one part of arsenic was considered to be ideal. At times this balance of copper to arsenic was almost impossible to obtain, especially when handling copper Cottrell dusts, which vary so greatly in copper and arsenic. Custom smelters like El Paso, handling a great variety of dusts, concentrates and ores, are apt to have anywhere from I to 15 pct copper on charge, with a variable in arsenic of from 0.5 to 2 pct. With such conditions, and drosses varying from 12 to 40 pct copper, an operator using the older dross reverberatory practices would find it just about impossible to control the reverberatory operations and to produce a good product low in lead and high in copper. These conditions prevailed at El Paso from the year 1940 to the present. In May 1942 it was decided to experiment with the soda process. The Soda Process After considerable work the soda method was finally evolved to the present state. It has never failed to produce a good product even under the most adverse conditions. It might be well to remember that many men of thought in the smelting industry have at one time or other sugge~ted the removal of all copper, arsenic and antimony from the lead blast-furnace charge as an aid to better metallurgy.

Jan 1, 1949

By NORMAN EBBLEY

NUMEROUS references have been made recently to "Alaska's oil reserves," and in view of the wartime petroleum situation sober thinking demands a dispassionate and scientific study and investigation of these reserves or supposed reserves. The question naturally arises, "Is there actually oil in Alaska, or are the reserves there a supposition?" True, in 1923 President Harding established Naval Petroleum Reserve No. 4 in Alaska, certainly implying that oil was there. This reserve, embracing about 35,000 sq. mi., was set aside on the advice of the Bureau of Engineering of the Navy Department and was based upon the existence of known petroleum seepages at Cape Simpson on the Arctic coast. The Cape Simpson seepages have been known for more than fifty years, but in spite of persistent rumors of other seepages in northern Alaska no definite evidence of their existence has been available.

Jan 1, 1944

By R. D. Brown

In his April 10, 1978 budget address, Finance Minister Chretien declared that the federal government will restrict the growth of its spending to less than the trend growth of the gross national product; over the past year, both the federal and a number of provincial governments have taken action to cut back on spending policies. This new emphasis in restraint would seem 10 be a response to a mounting public reaction to the rapid growth of government spending - and taxation - over the past 25 years. Although this relatively new government posture on public spending may be admired by many, to others it raises the question: "Can the growth in government spending really be stopped?" This article comments on just how government revenues - and spending - have grown over the past few years in Canada, and mentions some of the issues relating to a slowdown in that growth.

Jan 1, 1978

By Maria I. DeRosa

This Bureau of Mines report describes the Automated Breathing Metabolic Simulator and its hardware and software systems with emphasis on the role exerted by the software program subroutines in controlling the hardware mechanisms during the simulation of man's respiratory and metabolic functions.

Jan 1, 1978

By J. H. Johnson, H. J. Schock

The cases of no auxiliary ventilation and ventilation with tubing were mathematically modeled, using a turbulent dispersion model. The Scooptram® used to load is modeled as a variable-speed, variable-strength source of pollutants moving in and out of the dead-ended drift. Model predictions are compared to experimental measurements. A parametric analysis was performed to determine If a relationship existed between C02 and NO levels. It was concluded from this analysis that when modeling a load-haul-dump cycle, it is necessary to use a model that can predict changes in source strength as well as source location. Carbon dioxide was used as a tracer to calibrate the model since, knowing the fuel flow rate, it is possible to calculate C02 production. The model was then verified after this calibration process using additional experimental results. With the calibrated model, it is possible to predict pollutant concentrations at any location in the heading using an engine map and the previously calculated flow field.

Jan 1, 1984

By L. W. Fagg

The purpose of this paper is to present in a convenient form data and examples necessary in making dynamometer card analyses; also to outline a procedure of well weighing. Many articles and papers have been written delving into the mathematical considerations relative to the shape and characteristics of dynamometer cards. However. it is recognized that there are too many unknown factors involved in such calculations to assure a workable degree of accuracy. For this reason the accepted procedure is to take dynamometer cards on wells in question rather than try to calculate the load curve. The polished rod dynamometer is now recognized as a necessary tool for measuring loads, torque, and horsepower. It is also used to determine pump action and trouble-shoot for any seemingly abnormal pumping condition. The apparently infinite variety of a = maximum load (height x scale constant) b = minimum load. Range of load is difference between maximum and minimum load speed—taken with stop watch stroke —measured at polished rod c = beginning of down stroke in direction of arrow. (End of up stroke) d = beginning of up stroke. (End of down stroke). Polished Rod Horsepower = (Area of card) x Scale const. x Stroke x Length x spm (Length of card) 33000x 12 1.35 1.35------x5300x 24 x 12 2.53 --------------------------= 2.06 23000x12 Appraximate Peak Torque: Upstroke = (2390) (12) (1) = 28,700 in. Ib Downstroke = (1 860) (12) (.866) = 19,300 in. Ib Counterbalance should be increased to make up stroke and down stroke peak torque equal. FIG. 1 dynamometer cards that can be obtained is one reason for the general lack of usage of the dynamometer as a control instrument rather than a means for making routine measurements of leads and horsepower. When it is considered that the dynamometer card is a record of the resultant of all forces acting on the polished rod at any particular instant during the pumping stroke. the problem is then one of breaking down this resultant into its various components. As a means of a quick review we shall consider the examples shown in Figs. 1 to 9: and Tables I and II and then proceed to the interpretation of variously shaped cards caused by some abnormal operating condition. In Table 11, when we were considering the factors involved in calculating the peak polished rod load, it can be seen that the factors involved greatly oversimplify the problem. Certain assumptions are made which may or may not he even close to the actual field conditions, such as the specific gravity of the fluid generally considered as one; that the crank has constant angular velocity; that the down-hole friction is zero; and that the fluid lift is from the pump. In the following examples we shall see what a variation in fluid weight and friction can do to the general shape and magnitude of the dynamometer card. (Figs. 10 to 22.) MAKING THE WELL STUDY It is obvious that it would be impractical to consider in detail all of these factors each time a well study is made, inasmuch as each well study job could conceivably be extended into a research project rather than serve the practical requirements of finding the answer to a specific problem. For this reason it is important that some objective be established previous to the time the well study is made. Load at TU = 3070 Ib Crank angle when polished rod is at position TU = ? ? = 30° Maximum counterbalance effect at polished rod = 2760 Ib Torque at TU = (Load at TU — Max. counterbalance effect-lbs) sin 0 x Length of Stroke 2 = (3070-2760) .5 x 24 = 1860 in. 15 2 Torque at TD = (Load at TD — Max. counterbalance effect-lbs) sin ? x Length of Stroke 2 = (530 - 2760) sin 330' x 24 = 13,400 in. Ib 2 Note: sin 0 from c to d on UPSTROKE will be positive value. sin 0 from c to d on DOWNSTROKE will be negative value Torque at c and d is zero because 0 is zero. FIG. 2 —APPROXIMATE METHOD FOR CALCUlATlNG TORQUE

Jan 1, 1950

By I. Nishkov, I. Grigorova, N. Valkanov, M. Ranchev

The processing of sulphide ores with variable and complex mineral composition and physical properties, such as those processed by two-stage selective flotation scheme in “Erma reka” concentrator, Minstroy Holding JSC, requires excellent selectivity in order to achieve acceptable concentrate grades. The lead-zinc ores from the hydrothermal lead-zinc deposits mainly contain galena (PbS), sphalerite (ZnS), pyrite (FeS) and chalcopyrite (CuFeS2), as well as non-metal minerals such as quartz, carbonates and clinopyroxenes skarns. One of the main impurities present in sphalerite is iron, which is known to be detrimental to the rate of sphalerite flotation and its recovery. The results from the conducted laboratory and industrial tests, presented in the previous study, showed that it is possible to depress the iron rich sphalerite by adding MINFIT® (modified sulfur-oxy depressant) at the pH of approximately 9.5 in rougher lead flotation circuit, leading to reduction of zinc sulphate consumption and complete elimination of cyanides from the flotation process. Furthermore, the consumption of copper sulphate, which reactivates the surface of the zinc minerals, was significantly reduced. Consequently, the optimisation of the reagent regime in the Erma reka concentrator, led to notably improved qualitative (grade, recovery) properties of the final lead and zinc concentrates. Moreover, when comparing the reagents consumption for 2014 and 2016 – when the processing plant have been applying the new optimized reagents regime, comprises the use of MINFIT as the primary depressant, the following results have been achieved: ZnSO4 decreased by 30%; CuSO4 consumption decreased four times and full rejection of cyanides from the process. Finally, this paper provides a state-of-the-art review of the obtained results during the period of application of the new flotation reagents regime in the Erma reka concentrator, Minstroy Holding JSC.

Jan 1, 2018

By M. N. Shetty

LARGE copper whiskers were grown from cuprous iodide by reduction with hydrogen at about 500°C. Carefully selected single-crystal whiskers of [loo], [110], and [Ill] orientations were used and the whisker shapes and cross sections are shown in Fig. 1. Spec-trographic analysis of a typical batch of whiskers showed that the composition was better than 99.9 pct with iron and silicon as the major impurities. The test specimens varied from about 70 to 400 u in diam and they did not show a conspicuous yield drop as observed in very fine whiskers (diam <25 u), tested by Brenner.1 The characteristics of the stress-strain curves were similar to those of bulk single crystals, even though the maximum flow stresses reached in some orientations were comparable to the yield stresses observed in fine whiskers. Mechanical properties of whiskers of different materials and copper whiskers up to about 100 u in diam have been reviewed,&apos; and a mechanism of slip band propagation in fine whiskers has been recently suggested.3 Whiskers in this work were tested in a floor-model Instron testing machine using low strain rates. (Details of the testing procedure, diameter dependence of the yield stress, and the characteristics of the load elongation and stress-strain curves have appeared esewhere.4) Due to the extensive deformation, >50

Jan 1, 1970

By Z. F. Wang, W. K. Choi, A. E. Torma

The present study has investigated the bioleachability of low-grade and high-grade pyritic gold ores and the extraction of gold from the leach residues of bioleaching with thiourea solutions. Final gold extractions as high as 96% were obtained from the high-grade ore and above 93% from the low-grade ore. The gold extraction was found to follow the extent of pyrite biooxidation. Using a cyclic voltammetric technique and carbon-paste-FeS2 electrode it was found that the semiconductor pyrite oxidation involves many intermediate electrochemical reactions. Furthermore, the oxidation is solid-state diffusion controlled as suggested by chronoamperometric and chronopotentiometric measurements.Using Sand&apos;s approach, the activation energy of solid-state diffusion biooxidation of pyrite was determined to be AEa=22.4 kJ. A generalized model for the mechanisms of pyrite oxidation has been presented.

Jan 1, 1990

By A. D. Thomas, V. N. Rampton, S. Paradis, C. F. Gleeson

"A shallow till sampling program was completed on a 1 km grid over the St . George Batholith in southern New Brunswick. The ""B"" soil horizon was analyzed for Cu, Pb, Zn, Ag, Co, Mo, U and Sb and the heavy minerals from the ""C"" soil horizon were analyzed for W, Sn and A u. The results delineated four of five recorded W occurrences, three of four recorded Mo occurrences, all recorded Cu occurrences and one recorded Au occurrence. The results indicate that shallow till sampling in conjunction with bedrock and Quaternary mapping can inexpensively define exploration targets in terrain similar to that underlain by the St. George Batholith.A similar program was carried out in eastern Ontario involving the analysis of four separates from the till, the ""8"" soil horizon, the -50 mesh fraction, the -250 mesh and the heavy mineral fraction of the ""C"" soil horizon and humus. Also sampling was carried out near known gold occurrences at closer spacings. Regionally, anomalous results from all sample media clearly defined a large auriferous shear zone and associated splays. Over one known showing all media clearly defined the showing and a secondary zone. On the regional scale the heavy mineral fraction gave the best anomaly definition and contrast, but the -250 mesh fraction was found to be the most cost effective for defining exploration targets. For detailed surveys, humus was found to be cost-effective."

Jan 1, 1986

By A. A. Collins

OF widespread interest to all lead metal¬lurgists is a dross smelting process that will consistently give mattes and speiss of low lead and high copper contents. It is -a problem that has intrigued operators through the years. In the past few years, with increased amounts of copper and overcrowded metallurgical furnaces, it has been almost imperative to evolve some method. Experience at El Paso has shown that high copper-to-lead ratios can be consistently attained by use of the new soda process.* OLDER METHODS Three older methods; i.e., I. Dross plus siliceous ore and limestone, 2. Dross plus one fourth blast-furnace speiss and siliceous ore, 3. Dross plus sulphides and siliceous ore and scrap iron, do not give consistent results and the products are higher in lead and lower in copper than those produced with the soda process. Any radical changes in the blast-furnace drosses will throw any of these older methods into a tailspin. For almost ten years, El Paso used the third method, with varying results. It was noted that as the arsenic and antimony contents of the dross increased, the speiss and matte steadily increased in lead and decreased in copper. A dross containing four parts of copper to one part of arsenic was considered to be ideal. At times this balance of copper to arsenic was almost impossible to obtain, especially when handling copper Cottrell dusts, which vary so greatly in copper and arsenic. Custom smelters like El Paso, handling a great variety of dusts, concentrates and ores, are apt to have anywhere from 1 to 15 pct copper on charge, with a variable in arsenic of from 0.5 to 2 pct. With such conditions, and drosses varying from 12 to 40 pct copper, an operator using the older dross reverberatory practices would find it just about im¬possible to control the reverberatory operations and to produce a good product low in lead and high in copper. These conditions prevailed at El Paso from the year 1940 to the present. In May 1942 it, was decided to experiment with the soda process. THE SODA PROCESS After considerable work the soda method was finally evolved to the present state. It has never failed to produce a good product even under the most adverse conditions. It might be well to remember that many men of thought in the smelting industry have at one time or other suggested the removal of all copper, arsenic and antimony from the lead blast-furnace charge as an aid to better metallurgy.

Jan 1, 1947

In this study, numerical simulations of yield pillars employing the finite element method with time-dependent Drucker-Prager material model are conducted. The stress control mechanism of yield pillars on weak floor strata is studied. The development of pillar yield zone, the distribution of pillar stress and the development of failure zone in the weak floor strata are investigated. The study indicates that a properly selected yield pillar size may significantly reduce the peak stress induced in the weak floor strata and effectively control the development of failure zone in the floor.

Jan 1, 1999

By C. Birch

"A mineral resource royalty is payment to the holder of mineral rights for the utilization of the mineral resource. In South Africa, this payment is made to the State as holder of the mineral rights (The Mineral and Petroleum Resources Royalty Act of 2008). The principle purpose of this research paper is to identify if the State is benefitting from the mineral resource royalty by considering its impact on seven individual Witwatersrand gold mines.For this study, a simple financial optimiser model was created in Microsoft Excel that links the ore flow, block listing and the cash flow (excluding or including the cost of the mineral resource royalty). Mixed integer linear programing (the Excel Solver function) is utilised to optimise either profit or NPV (at 9% and 12%) by adjusting the cut-off grade.The impact on each of the seven mines mine was different but overall R7.9 billion is estimated to be paid in mineral resource royalty over their expected remaining lives. Due to the cost of the mineral resource royalty and increasing the cut-off grades, the total revenue decreases by R10 billion. A significant portion of this lost revenue would have been paid to the State in the forms of other taxation including company income tax which decreases by R2.8 billion. It is recommended that an industry wide investigation be conducted to determine if the resource royalty is adding to the State’s revenue, or destroying value including premature job losses. IntroductionTaxation of mining companies has become a very topical subject in the context of the postapartheid South African economy. There have been increasing calls for equitable re-distribution of mineral asset wealth for the benefit of all South African citizens and not just to an elite few. As part of the Mineral and Petroleum Resources Development Act (MRDPA) of 2002, the Mineral and Petroleum Resources Royalty Act of 2008 was introduced and came into effect in 2010 (South African Revenue Services, 2008). A mineral royalty is payment to the holder of mineral rights for the utilization of the mineral resource. In the case where the holder of the mineral right is the State, then this payment is made to the State (Cawood, 1999). Studies on the potential impact of the mineral resource royalty on the minerals industry have been conducted during the formulation of the Act and subesquently. These include Cawood and Macfarlane (2003), who suggested a cap of no more than 3% (Cawood and Macfarlane, 2003), as well as Cawood (2011), who predicted rising cut-off grades and thus reducing mineral reserves. In 2013, Grobler completed a Masters in the Faculty of Economic and Management Sciences at the University of Pretoria and concluded that the impact of the mineral resource royalty on the economy is positive. She stated that the royalty has caused operating expenses to increase, but this does not appear to be significant. Furthermore, she stated that the royalty has not affected the way the mining industry operates (Grobler, 2014)."

Jan 1, 2016

By Molood Saeedi, Nima Sadeghi, Eskandar Keshavarz Alamdari

This study showed the kinetics of gold chlorination leaching from an anode slime complex containing copper, silver, barium, selenium, and tellurium. AgCl and BaSO4 control the rate of gold leaching, and the interface transfer and diffusion across the product was selected as the desirable kinetic model. The concentration of hydrochloric acid, chlorine gas flow rate, pulp density, and temperature have been precisely studied. The results showed that temperature and hydrochloric acid have a favorable influence on the leaching rate. However, the chlorine gas flow rate is inactive in the reaction rate. Furthermore, the leaching rate decreased with an increasing pulp density. The leaching process was controlled by the interface transfer and diffusion across the product, and the activation energy was determined to be 13.66 kJ mol–1.

Oct 19, 2021

By H. L. Bibbs, H. D. Snedden

"INTRODUCTION The use of beryllium and its alloys has increased rapidly during the last decade. Further expansion of its use is limited; in part, by lack of adequately developed ore reserves. The principal commercial beryllium mineral is beryl, which is found chiefly in pegmatites and produced for market as a byproduct of the mica and feldspar industries. The coarse beryl is mined selectively, sobbed and sorted by hand, and then sold without further beneficiation. The known reserves of coarse beryl are small. No method has been available for concentrating small disseminated beryl crystals, so ores of this type have not been mined or have been left on waste dumps. Disseminated ore in low-grade unmined areas and waste dumps on developed properties is a potential source of beryl, provided a method is developed for its beneficiation.Published literature on the concentration of beryl is lacking in detail or deals chiefly with tests on artificial mixtures of pure minerals, and procedures as given were not applicable to the beryl ores tested at the Salt Lake Station. The testing procedures described in this report are independent developments. By employing these procedures, beryl was satisfactorily con¬centrated from several run-of-mine and dump ores, although these ores wore low in grade and part of the contained beryl was finely crystalline and disseminated.Beryl, quartz, and feldspar, when ground to flotation sizes, are so alike in color and general appearance that they cannot he distinguished by visual observation. The progress of the work depended on rapid determination of the grade of test products by means of the petrographic microscope. Small samples of concentrates and tailings were often cut after each addition of reagents, dried, and examined under the microscope."

May 1, 1947

By Fred P. Peters

At first glance this paper may seem unique among those comprising this symposium on designing for powder metallurgy, since it is evidently concerned with everything but Powder metallurgy. This paradox mill be at once resolved, however, when the real Purpose of the symposium meeting is understood—to present factually and objectively the things that can and cannot he done with powder-metallurgy methods, and especially to set forth with brutal frankness the limitations of Powder metallurgy, so that costly over-enthusiasm and misapplication may be prevented. Since much of powder metallurgy&apos;s future development (and many of its present disappointments) has been in competition with other and long-established methods of fabricating parts, it is easy to see that its true competitive possibilities in any given case cannot be accurately appraised without rudimentary knowledge of what the competition can do. This paper, therefore, presents a few reminders of things you all know—a background to be kept in mind as you examine the data on each of their specialties given by the authors of the papers that follow. From the standpoint of the design engineer powder metallurgy is often in Competition with one or more of the following: sand casting, die casting, permanent-mold casting, precision investment casting, ma- chined bar stock, screw-machine parts, cold-heading, drop-forging, and stamping and drawing. We will here briefly discuss each of these individually, and set forth so, rough (and therefore dangerous) generalizations about its competitive position, especially with respect to powder metallurgy. Sand Casting Sand-casting of small parts is sometimes an inexpensive method of manufacture, for its raw-material costs (i,e., for gray iron) are the lowest of the various methods and it involves the use of no tools and dies of jewelry quality. its design flexibility— that is, the ability to make complicated, cored and undercut parts in one piece—is about the highest of the competing processes and in this respect it can do many things that are impossible by powder metallurgy. For small castings its production rates may be higher, by using multi-impression molds, than can be achieved with parts of the same size by powder metallurgy. But its labor charges for melting, pouring, patternmaking and molding are comparatively high and the waste it entails in gates and risers is always considerable. Tolerances of sand castings are wide (+1/6 to 1/32 in- per in.) and where precision approaching that of powder metallurgy is required sand castings must be machined to final size, thus increasing their cost. Steel sand castings are more expensive and less precise than iron, and nonferrous the most costly of all.

Jan 1, 1945

By J. W. Leonard, J. C. Anderson, C. T. Holland

PREPARATION CONTROL IN UNDERGROUND MINING Selective Mining According to district Depending upon the particular geographic location or seam characteristics modem raw coal preparation practices can be used to obtain improved product quality and uniformity. Nevertheless, certain coal markets may require only marginal quality while others may require very high quality and these objectives may be sought by commencing the preparation of coal underground at the "working face." Underground preparation involves choosing those portions of the bed which can be cleaned to satisfy predetermined market requirements involving (1 ) maintenance of uniformity in chemical quality, (2) elimination of removable impurities, (3) control of sizes and size ratios and (4) control of moisture. The methods employed to attain these objectives vary widely with the (1) seam under development, (2) mining equipment available and (3) changing trends in the consuming markets. When a mining property is opened and development progresses from one section to another the (1) petrography of the coal in the bed does not re- main uniform, (2) character of roof and floor are subject to change and (3) character and prevalence of mineral impurities are subject to considerable variation. The quality of coal shipped to market from any mine depends upon intelligent foresight, planning, execution and supervision. Mining becomes a highly technical art. The quality of coal as determined by chemical and petrographic analysis is without question one of the most important considerations in the development and life of any coal-mining property. Variations in such proper- ties as volatile matter, ash, sulfur, Btu content and petrography are of considerable interest and to a limited extent so are such properties as phosphorous content, free swelling index, plasticity, hardness, pressure formation during coking and ash composition. The maximum and minimum specifications of these characteristics as established by competitive market conditions place definite limits on the marketability of a coal. The prospecting and evaluation of any area containing one or more salable coal beds by means of channel samples taken from outcrop openings and/or from diamond-drill cores can yield valuable data on coal characteristics. By correlating the data developed from distinct petrographic sections of channel and/or drill core samples, the quality of the bed according to stratification will be evident. There are few coal beds that do not show wide variations of such characteristics as ash and sulfur

Jan 1, 1968