Search Documents

By Richard E. Hucko

The bureau of Mines conducted a laboratory scale investigation of the process of selective flocculation with the objective of developing a method to effect separations on suspensions consisting predominately of ultra-fine-size (minus 400-mesh) particles of coal and refuse. Selective flocculation of coal from coal-refuse slurries could be achieved with a wide variety of reagents. Typically as much as 15 to 20 weight-percent of high-ash solids (70 to 80 percent ash) could be retained in suspension. The flocculated sediment remained a high-ash product, however, and would require further treatment to be regarded as clean coal. No combination of reagents and conditions led to selective flocculation of the refuse component. The dispersing agent was found to be the critical factor; dosages of 3 to 8 lb/ton2 were necessary to stabilize the suspension for subsequent selective flocculation. In addition, most of the dispersants that worked were most effective at substantially elevated pH (11 or so). It was concluded that this process would be prohibitively expensive and, because of yield and quality constraints, it would be of questionable utility in today's coal preparation industry.

Jan 1, 1977

By D. Reddish

The combination of free standing steel supports, such as arches, and rock bolts (mixed support) has Frequently been in used in UK coal mine roadways when it is considered that the strata and/or environmental conditions would not be suitable for rock bolts solely. However, how such mixed support systems operate is not fully understood. Due to the differences in the support method provided by rock bolts and free standing steel, the total support generated is not simply a case of adding the contribution to the support of the roadway given by the two systems. This paper describes a numerical investigation into mixed support systems when used in coal mine roadways. A series of 2D and 3D geomechanical models are described and the method of modelling the rock bolts and steel supports in coal mine tunnels is discussed. The numerical models described include rock boltd only roadways, steel supported roadways and mixed supported roadways in a variety of geological and in-situ stress conditions. Conclusions are formed that allow an insight into mechanisms of strata reinforcement provided by the support systems modelled. Further to this, a review of the numerical modelling of pre-tensioned rock bolted systems is described identifying the contribution to support efficiency given by the adoption of tensioning in full column resin anchors. The results obtained highlight that the effectiveness of the pre-tensioned load is dependant on the rock mass quality and in- situ stress level at the site where it is to be used.

Jan 1, 2004

By I. J. Corrans

Wet high-intensity magnetic separation (WHIMS) has been successfully applied to the recovery of gold and uranium from the residues of Witwatersrand ores. Good overall recoveries have been achieved for particles as small as 12µ, and finer particles of uranium minerals are recovered when present as inclusions. The best results were obtained with a matrix of soft-iron balls 6 mm in diameter. However, pilot-plant tests drew attention to a major defect of the machine: the matrix could be blocked by wood chips and ferromagnetic particles. This problem was overcome by the incorporation of a modification that allows the balls to be discharged from the rotating annulus. Two full-scale units that incorporate the modification have been installed.

Jan 1, 1980

By M. D. Scott

"Highland Valley Copper recently installed a semi-mobile in-pit crushing and conveyor system designed to feed both the Bethlehem and Lornex concentrators with a feed averaging 120000 tonnes per day. The system installed with a rated capacity of 12000 tonnes per hour is the highest capacity hard rock semi-mobile crushing and conveying system currently in existence.The system is designed in a manner that the crushers can be moved easily as the pit is developed in depth with conveyors extending deeper into the pit, and conveyors being moved radially from a surge pile located at the rim of the ultimate pit as the pit increases in size laterally.The system consists of two 6000 tph, 60 by 89 Krupp semimobile crushers feeding two moveable 4500 hp, 60 in. conveyors, 1.25 km long feeding a 7500 tonne live storage surge pile. Two 96 in. belt feeders installed in reclaim tunnels under the pile feed two parallel 4500 hp, 60 in. conveyors, 1.25 km long on a 12 per cent uphill grade to the two existing Lornex plant feed conveyors. A third 96 in. belt feeder, under the pile, feeds a 60 in. conveyor, loading trucks hauling crushed ore to the Bethlehem mill.A description will be given: (1) of the system's design features in which climatic extremes, operating, and maintenance characteristics were of primary importance; (2) of the way the system was constructed from components purchased internationally on an extremely tight construction schedule; and (3) of the way the system has operated during the first few months in operation during which time it demonstrated that it has met various design criteria."

Jan 1, 1988

The Prominent Hill copper-gold deposit is located approximately 150 km north west of Olympic Dam, on the southern margin of the Mount Woods Inlier in South Australia. Its discovery in November 2001 resulted from the application of a geological model developed from geological, geophysical and petrophysical data pertaining to the Olympic Dam deposit. The discovery has dispelled the notion the Olympic Dam may be unique, and that another deposit like it is unlikely to be found. The Prominent Hill mineralisation is hosted by haematite-matrix hydrothermal breccias, which have suffered extensive iron-sericite-silica alteration and overprinting. Copper, gold, barium, fluorine, uranium, cerium and lanthanum are all intrinsically associated with the hydrothermal iron. Breccias intrude an east-west striking, fault-controlled sedimentary succession, which is flanked to both the south and north by volcanic complexes. Many similarities between Prominent Hill and Olympic Dam are documented including geological setting, mineralogy, breccia styles, and alteration. Differences relate largely to the nature of the immediate host rocks. The similarities and difference provide key data for improving exploration models for this style of iron oxide copper-gold deposit, both within the Gawler Craton as well as globally.

Jan 1, 2004

By J. B. Boisvert, W. Board, C. R. Mooney

"Traditional geostatistical modelling methods are difficult to apply to heavy-tailed deposits because the extreme positive skew of the grade distribution leads to bias. The focus here is on an innovative method of modelling the high-grade population by conditionally simulating discrete volumes (nuggets) of gold with marked Poisson and Cox processes. Capping and other ad-hoc manipulation of the assay data is not required; however, an intensity map for the point processes is required. The method is demonstrated on a dataset from an epithermal deposit and demonstrates an improvement in reducing smearing and controlling the skew of the grade distribution.RÉSUMÉ Les méthodes traditionnelles de modélisation géostatistique sont difficiles à appliquer dans des gisements dont la distribution de la teneur est à queue lourde car l’extrême asymétrie positive de la distribution de la teneur génère des biais. Dans le présent article, l’accent est mis sur une méthode novatrice de modélisation de la population à haute teneur par la simulation conditionnelle des volumes discrets d’or (pépites) au moyen de procédés marqués de Poisson et de Cox. La limite d’utilisation et d’autres manipulations ad hoc des données ne sont pas requises; toutefois, il faut une carte des intensités pour le processus ponctuel. La méthode est démontrée sur un ensemble de données d’essais provenant d’un gisement épithermal et elle montre une amélioration dans le lissage du flou et dans le contrôle de l’asymétrie de la distribution de la teneur."

Jan 1, 2015

By Peiwei Hu, Min Lu, Tiejun Chen

Based on the analysis of properties of vanadium tailing (VT), the surface modification study was carried out as a polymer filler. The modification effects of the three kinds of coupling agents on VT and the mechanical properties of polypropylene (PP) composites with a modified vanadium tailing (MVT) were compared to determine the suitable surface modification agent and modification processes for VT. The results show that the best one is aluminate coupling agent DL-411. When the content is 1.2 wt% and the temperature was 100 °C, the activity index of modified vanadium tailing (MVT) is 95.53%. FTIR analysis shows that DL-411 has the strongest binding ability on VT. XRD analysis shows that VT has a heterogeneous nucleation on PP to induced b form formation, and DL-411 could enhance this nucleation. So the composites has higher strength and better toughness. When the content of MVT is 10 phr, the tensile strength, impact strength, flexural strength and flexural modulus of the composites are 47.51 MPa, 38.43 kJ/m2, 59.57 and 1654.36 MPa, respectively.

Mar 1, 2018

By Denise Corrêa de Oliveira

Common dry batteries use zinc as the negative electrode. Producers commonly use additives such as mercury to prevent corrosion and to increase the mechanical resistance of the zinc anode. Alkaline batteries also contain it, as an anti-corrosive agent. When mixed with the common municipal solid waste, heavy metals as zinc and mercury pollute soil and ground water supplies, moving to the food-chain and affecting human health. Due to these possible damages, this kind of waste must be properly disposed, or recycled. Thus, even in low amounts (ppm) in batteries, mercury has to be eliminated or, at least, its content should be reduced. This work presents the use of pyromettalurgical processes, to reduce mercury content and recover zinc. The tests involved batteries treatment at temperatures from 300° to 1000°C. Mercury is eliminated up to 650°C, and zinc is evaporated at higher temperature treatment. C

Jan 1, 2001

The trend for using larger equipment in open pit mining to achieve cost effectiveness raises the question about the optimum economic point of scale in the current world of globalization. The present paper treats this question through the prism of a new methodology of assessing the impact of the size of production equipment on the economic outcomes of coal mining ventures. The methodology incorporates a production scheduling optimization model that implements both principles of mine planning, coal quality optimization and waste deferment. The implementation of the waste deferment principle dealing with the spatial and time aspects of the mine sequence arrangement allows the adequate modeling of the optimality of production equipment scale through the use of mine investment parameters, such as, purchase and ownership costs and discounted cash flows analysis. A case study is provided to illustrate the applicability of the new methodology.

Jan 1, 2004

By W. Rostoker

IN the course of the development of the phase equilibrium diagram for the system Zr-Cr,' the structure of an as-cast allov having the composition ZrCr2 was analyzed and established to be isomorphous with MgZn2 (C14, hexagonal lattice, 12 atoms per unit cell). In a recent paper on the same system, Hayes, Roberson, and Davies' report for the ZrCr2 phase an isomorphy with MgCu2 (C15, cubic lattice, 24 atoms per unit cell). It appeared that this conflict might be resolved by assuming a high and low temperature modification for ZrCr2. That this was the case with the phase TiCr2 has recently been demonstrated by Levinger." Specimens of ZrCr2 annealed at 1200°, 1100°, 994", 900°, 834", 800°, and 700°C, respectively, and subsequently quenched were examined by X-ray diffraction analysis. It was successfully demonstrated that a transition from the MgZn, structure at lower temperatures to the MgCu, structure did occur at some temperature between 900" and 994°C. Table I lists the observed structures at the various annealing temperatures. In Table II, a summary of line spacings and intensities is given for each of the allotropic modifications. The first six lines of the MgCu2 structures have been located in the table to illustrate the close similarity between the patterns. Lattice parameters of the two modifications were calculated by a least squares solution of equations for interplanar spacings for a series of high angle lines. The results are as follows: MgZn2 type - c = 8.262 kX, A = 5.079 kX. MgCu2 type — a = 7.195 kX. It is interesting to note that TiCr2 behaves in reverse fashion yn that the MgCu, structure is the low temperature modification and the MgZn2 structure is the high temperature modification. References lR. F. Domagala, D. J. McPherson, and M. Hansen: This issue p. 279. 'E. T. Hayes, A. H. Roberson, M. H. Davies: Trans. AIME (1952) 194, p. 304; Journal of Metals (March 1952). 3B. W. Levinger: Trans. AIME (1953) 197, pp. 195-196; Journal of Metals (February 1953).

Jan 1, 1954

By Mingfei He, Yude Gao

"The leaching kinetics was studied during leaching of indium-bearing zinc oxide to recover indium. The effects of temperature, sulfuric acidity, particle size, stirring rate on dissolution rate of indium were investigated. Results showed that the leaching process was controlled by chemical reaction at the condition of low sulfuric acid concentration. While the acidity increased to 1.8 mol/L, the leaching process was transformed into an internal diffusion controlling model . The corresponding value of reaction orders under low acidity and high acidity were 1.194, 0.156, respectively. Further calculation results indicated that the leaching reaction activation energy was only 10.97kJ/mol under the condition of high acid. The leaching rate constant was inversely proportional to the square of particle size, while the effect of stirring rate on leaching process was insignificant. The leaching process can be enhanced by increasing the temperature and acid concentration, as well as the decrease of particle size. And a final kinetics eqution was proposed. KEYWORDS Indium, extration, leaching kinetics, zinc oxide INTRODUCTION Indium[1,2] plays an important role in many aspects of living and industrial production owning to its special physical and chemical properties. The reserve of indium is rare on the earth, and most of indium is distributed in some other minerals[3]. Some researchers [4,5] have proposed that indium mainly substitutes for the lattice of other minerals by isomorphous. Therefore, the extraction of indium should take into account of the production technologies of those minerals to comprehensively recover the valuable metals."

Jan 1, 2018

By A. E. Cameron

The theory of atomic distribution of the stranger atoms in the space lattice of the solvent metal has been well developed by Rosenhain. It has long been known that the addition of one metal to another to form a solid solution increases the strength and hardness of the solvent metal. This increase is practically proportional to the amount of added substance up to the limit of solid solubility. To account for this increase in hardness and strength, Rosenhain assumes that the stranger atoms occupy positions on the solvent metal space lattice. Atomic attractions about the stranger atoms will not be the same as in the case of the pure metal, and there will thus be a disturbance of the orderly arrangement of the atoms on the space lattice, or a distortion of the lattice. Such a disturbance would interfere with the ease of slip along the planes and would thus tend to promote strength and hardness. Rosenhain notes that not only may there be a local disturbance of the lattice about the stranger atom but there may well be also a measurable change in the dimensions of the lattice as a whole. The relative amounts of local and general distortion of the lattice will depend upon the nature of the lattice itself. As Rosenhain says, "If the lattice is comparatively soft and flexible the distortion is likely to be largely local. In a stiff lattice, however, local distortion will be resisted and there will be a correspondingly increased general distortion."

Jan 1, 1927

By M. F. El-Demerdash

The activity distribution diagrams for different species in aqueous systems are developed. Computational method may be considered as an extension of the Activity-Term method introduced by the authors to construct EH-pH diagrams. In the Activity-Term method, all activities of different species are evaluated before deciding the most stable one. In the present study, a factor is assumed to allow for the conservation of the element. At any point, the total concentration of all species should contain only the input m moles of the element (elements) considered. This approach is applied to Zn-, 5-, and Zn-S-H2O and activity distribution diagrams are plotted as a function of pH, at different potential levels and at different temperatures.

Jan 1, 1990

By R. L. Miller

Two samples of iron enriched basalt (IEB) containing simulated nuclear fuel and having two distinct microstructures were prepared and tested for uranium recovery. The IEBs are refractory towards leaching by ground water. However, the uranium content (15.8%) is high enough that if aggressive leaching techniques are used for uranium recovery, these materials could be considered as man-made uranium ores. The IEBs discussed in this report were prepared to simulate Three Mile Island-2 core debris. The crushed IEBs were treated using three different methods simulating potential industrial scale processes. In one method the IEBs were fused with sodium hydroxide then the cooled mass leached first with water then with dilute sulfuric acid; about 52% of the uranium was recovered in this case. In the second method the IEBs were treated with a sulfuric acid/hydrogen peroxide lixiviant and about 13% of the uranium was recovered. In the third technique the IEBs were leached with a sodium carbonate/sodium bicarbonate/hydrogen peroxide solution. Only about 0.1% of the uranium was recovered. The results of these screening tests suggest that the IEBs can be successfully treated for recovery of the contained uranium. Other studies would be required to determine if other values, such as zirconium or silver, could be recovered from the IEBs.

Jan 1, 1984

By AIME AIME

TWENTY-TWO sections and all four of the divisions sent delegates to the annual meeting. They became so interested in the wide ranging dis6ussion of old and yet ever-new problems of Institute affairs that three instead of two sessions scheduled were necessary. Monday morning the meeting assembled with President Bassett presiding in the absence of President-elect Tally, who had been called to Baltimore by the serious illness of a brother. Thursday morning Vice-president Turner presided until Mr. Tally appeared after which the latter guided the sessions. Since reports from all of the active sections save one had been mimeographed and sent in advance to the delegates, detailed reports from each were dispensed with. The discussions dealt largely with membership problems, both local and national, with financing, speakers and programs, visits from national officers, and the conduct of the annual meeting. Many interesting and constructive suggestions were made and will be reported back to the sections by the delegates.

Jan 1, 1931

By T. N. Matveeva, L. B. Lantsova, N. K. Gromova

"Multimetal gold-antimony ores are complexed processing products, since they are characterized by veindisseminatedsulfide mineralization with fine-dispersed submicroscopic gold, low content and uneven distribution ofAu, which is concentrated together with iron sulfides (pyrite, arsenopyrite, pyrrhotite). Such ores are classified asrefractory ones and characterized by low gold recovery rates during cyanation. A particular feature of gold-antimonydeposits is the presence of antimony in industrial concentrations therein, along with gold that significantly increasesthe value of these deposits. The main antimony mineral is antimony sulfide - antimonite (stibnite). Gold-antimonyores undergo flotation concentration with producing collective gold-containing concentrates or gold sulfide andantimony concentrates. The purpose of the work is an experimental study of the flotation separation mechanism ofsulfide minerals of copper, antimony and arsenic using tannin-containing modifiers during processing of multimetalgold-bearing ores. During the research it was established that for the selective separation of antimony and arsenicsulfide minerals into concentrates of different kinds, it is possible to use vegetable reagents capable to be selectivelyadsorbed on the arsenopyrite surface. Using the laser KEYENCE VK-9700 and electronic LEO-1420 VP INCA-350microscopy methods, it has been established that the film of a vegetable modifier was not washed off with water andfixed firmly enough on the surface of the polished sections of arsenopyrite. In the X-ray spectrum there are C and Obands related to the reagent structure. The vegetative reagent is fixed both on the pre-adsorbed phase of the collectorand on the areas free from the collector. On the polished sections of antimonite before and after a contact with thetannin solution, only partial adsorbed tannin phases are detected, which disappear as a result of subsequent washingwith water.The reported study was funded by RFBR according to the research project ? 16-05-00646 ?."

Jan 1, 2018

By Spencer Peng, Larry Wasik, Akram Alfantazi, Michael Mahon

A dynamic simulation of a zinc tankhouse is a potential tool to improve tankhouse production and cost efficiencies. A fully dynamic simulation has potential uses in the design of new tankhouses as well as in the optimization of existing facilities. Equations from previously validated models of a single cell have been adapted to the industrial dynamic process simulation software, CADSTM Plus. Based on the inlet concentration, current density, and electrode setup, the simulation can predict many parameters, including outlet concentrations, flow rates, current efficiency and energy consumption. Multiple cells have been simulated simultaneously, allowing for an entire hypothetical tankhouse to be modeled. The simulation can be used to dynamically predict the conditions in a zinc tankhouse throughout an operation time scale. Further applications of this model include, tracking impurity buildup, modeling of recycle streams and the development of new flow regimes within the tankhouse.

Jan 1, 2012

Ranger Uranium Mines (RUM) operates an open cut located in the Top End of the North- ern Territory. Strict environmental controls govern all operations and the water management requirements have the greatest impact on mine planning. The two main goals of planning are to provide mill feed and to mine sufficient suitable quality waste rock for ongoing con- struction of the tailings dam. Early planning concentrated on staged development of the pit to provide access to as much ore as possible for a given amount of development. All waste was considered to be suitable construction material. Grade control of crusher feed was the main problem in planning, as wide vari- ations occur in ore grade over relatively short distances. Water management for the site ope- rates a no release' system for contaminated waters. Design storage has proven inadequate, and the open cut has been used as the extra storage. As construction of future stages of the tailings dam requires non-mineralised rock materials which meet specific quality criteria, the mine has had to re-examine long term plan- ning and pit development strategies. This has entailed the collection of much data not re- quired under normal mining conditions, such as the assaying of waste drill core. The overall impact on mine planning of the environmental regulations has been to alter the philosophy of earlier planning, making it necessary to create a new strategy for pit development with

Jan 1, 1984

By W. Kennedy Gauger, Tim Oolman, Debra L. Bisson

Radian Corporation (Radian) has developed a process for treating Cr(V1)-contaminated soils that involves: 1) soil washing using an alkaline extractant, 2) biological reduction of Cr(V1) to Cr(II1) in the soil wash effluent, and 3) separation of Cr(II1) from the biologically treated effluent. Biological treatment has been demonstrated for immobilized cells in fluidized bed bioreactors and suspended cells in slurry bioreactors for Cr(V1) levels ranging from 30 to 600 mg/L which have been reduced to non-detectable levels (< 0.05 mg/L; method detection limit [MDL]) during hydraulic residence times as short as 12 hours. The resulting Cr(II1)-containing effluent stream was chemically treated to precipitate chromium hydroxide for removal by physical separation.

Jan 1, 1995

By Thomas K. Chow

For the well-being of all living creatures and in response to green-environment policy from governments around the global, it is essential to reduce SO2 emissions from mining / smelters as well as other industrial facilities around the globe. However, often times, these SO2 containing flue gases and smelter flash gases also include oxygen and SO3, which complicate the SO2 removal process and technology. There are many novel technologies recently developed for removing SO2 from such gases. Most of these, however, have not yet commercially demonstrated that they are technically viable and economically feasible. Many of these novel processes also generate undesired byproducts, which themselves then need to be disposed of in a safe and cost effective manner. Fluor has developed the Fluor SOx Cleanup Process with a wide variety of process configurations to customize removal of the undesired flue gas constituents in a cost-effective manner. The process removes practically all SO2 in the form of salable elemental sulfur and also reduces CO emissions. Successful operation of major components of the Fluor SOx removal technologies has been demonstrated in many commercially operating units. Besides their technical viability and economic feasibility, Fluor SOx removal technologies do not generate any undesired byproducts or encounter SO2 associated corrosion issues. Moreover, these technologies produce high-purity, saleable elemental sulfur. This paper discusses the merits of the Fluor SOx removal technologies, their technical and cost advantages, their simplicity in design and operation, and their readiness for implementation.

Jan 1, 2006