Search Documents

By Rafael Lopes

Os aços utilizados na fabricação do vergalhão CA50 conforme norma NBR7480 são usados em todo o Brasil. A grande aplicação deste tipo de produto é na indústria de construção civil em função de sua excelente resistência mecânica e soldabilidade. Estas características permitem o avanço na construção de grandes empreendimentos. Em 2009, a Votorantim Siderurgia na sua Unidade de Resende, iniciou a produção do vergalhão CA50 em escala, procurando aumentar a sua participação no mercado de construção civil. Foi identificada uma grande variação nos resultados de limite de escoamento nos ensaios de liberação de produto realizados a partir de amostras coletadas no início das bobinas de vergalhão CA50. Em função disso, foi feita a caracterização do limite de escoamento e microestrutura ao longo da bobina onde foi identificado que esta grande variação do limite de escoamento estava presente em toda a bobina. Desta forma, foram definidos os principais parâmetros do processo de laminação que poderiam estar influenciando na variação do limite de escoamento e realizado um planejamento de experimentos (DOE) para o vergalhão CA50 16,0mm, aço 1030, onde foram identificadas que a combinação da melhor distribuição da vazão de água nas Caixas d’água utilizadas no tratamento térmico de têmpera e auto revenido, somada à maior distribuição das espiras no pelo Formador e à ventilação do Stelmor no mínimo apresentaram resultados de limite de escoamento acima do mínimo especificado pela norma NBR 7480 com menor desvio padrão quando comparado aos parâmetros de processo que eram utilizados na produção do vergalhão CA50.

Oct 30, 2017

By D. C. McKechnie

To the examining engineer, the ever-recurring problem involving the valuation of ore in a prospect presents at different times highly divergent aspects- some entirely physical or mathematical, others essentially personal. The majority of the problems discussed in this paper are obvious to the engineer, and need little elaboration. By the prospector and the general public, however, a number of these questions are often and completely over-looked, or else approached in such a way as to produce final results which are, to say the least, misleading and at times decidedly erroneous. While the purpose of this paper is to deal with prospects or potential mines, many of the problems considered apply equally well to mines with developed ore reserves. As the usual showings on a prospect consist chiefly of a few open-cuts and a limited amount of underground development work, an estimation of the actual ore reserves is a question of minor import, and seldom enters appreciably into an estimation of the probable value of the particular property. The physical valuation of a prospect mainly involves the consideration of such subjects as the general geological features exposed, the strength and type of mineralization, the width and persistence of any associated veins, shear zones, fractures or contact zones, together with the possible grade, size, and continuity of any ore-bodies that may there occur.

Jan 1, 1930

By M. Misra

The removal of lead and other heavy metals present in an active US Army small arms firing range soil was evaluated in a pilot scale test program at Ft. Polk, Louisiana. Two different acid based extraction processes in conjunction with conventional physical separation methods were used. Physical separation processes consisting of screening and gravity operations removed most of the coarse lead particulates and slugs. Hydrochloric acid leaching followed by precipitation of lead as hydroxide recycled clean soil containing less than 500 mg/L. total lead and less than 5 mg/L TCLP lead. Lead extraction efficiency with hydrochloric acid was 96 percent. The results of lead removal by physical separation in conjunction with acetic acid leaching were not consistent over the whole test period and the total soil processed.

Jan 1, 1998

By A. J. Lynch

Mineral processing models have been discussed for many years but it was not until digital computers became available about 1960 that serious attempts at circuit simulation could be carried out. Even then the work was primarily academic until PCs could be used by engineers in plants and design offices in the mid-1980s. Since then simulation has moved quickly and it is now at the point that most processes can be simulated reasonably accurately for purposes of design and optimization. There are still some significant deficiencies, notably in dry grinding and separation, and in the chemical interactions in flotation. Future work will involve: ?improvements of existing models ?dynamic simulation for automatic control and, in particular ,for training which is a weak link ?using advanced simulation models to predict liberation and separation from data acquired from SEM-based liberation analysers. Eventually mineral processes models will be part of total simulation systems which will incorporate mining and downstream processes including all environmental impacts.

Jan 1, 1999

By S. J. Hussey

The Bureau of Mines investigated the applicability of carbon-in-pulp pro-cess for recovering silver from low-grade ores. The reasons for the research were (1) to illustrate a practical procedure for the process design of carbon-in-pulp adsorption circuits using leach slurries and simple equipment; and (2) to illustrate how equations of adsorption theory relating rate data and equilibrium adsorption curves can be helpful in process design. Carbon-in-pulp silver adsorption tests were made on Banner, Idaho; mine-run ore samples with silver contents ranging from 2.0 to 8.5 oz/ton and variations in cyanide leach extraction from 48 to 93 pet. The lower recoveries were attributed to the presence of complex silver sulfide minerals. Carbon-in-pulp batch adsorption tests provided rate data for the estimation of a silver equilibrium adsorption curve. Process design procedures in which the rate data were related to an equilibrium adsorption curvey by equations of adsorption theory were used to plan a four-stage pilot plant cascade. The pilot plant was successfully operated for 45 hr of countercurrent flow, producing a carbon product containing a mean silver loading of 571 oz/ton from a pregnant solution of 1.7 oz/ton of silver. Virtually all of the dissolved silver was recovered on the carbon.

Jan 1, 1978

By M Muzammil, S. Mukerjee, S. Saran, M. Bharathi

"This paper presents the results of in-situ tests conducted on a set of under-reamed piles in a silty sand deposit. Three piles (i.e. vertical, vertical with one bulb and vertical with two bulbs) of diameter 0.2 m were cast upto a depth of 5 m. The pile cap had four foundation bolts cast into it so that a mechanical oscillatormotor assembly could be mounted centrally on it. The oscillator-motor assembly was used to generate purely sinusoidal dynamic forces, in either horizontal or vertical directions. For both horizontal and vertical vibration cases, it was observed that (i) the natural frequencies decreased with an increase in the excitation force level, (ii) for the same excitation level, the natural frequencies as well as the maximum amplitude of vibration are almost the same irrespective of the pile geometry i.e. number of bulbs in the pile, indicating that the full pile length is not being excited. For the vertical vibration case, the soil-pile stiffness at frequencies, before resonance, were observed to be higher than those at frequencies after resonance. In the horizontal vibration case, the stiffness of the soil-pile system was found to be decreasing with an increase in the excitation force level. The damping ratio was found to be increasing with an increase in the excitation force level.INTRODUCTIONUnder-reamed piles are piles, normally upto a depth of 6 m, with one or more bulbs along the pile stem. These have been used for structures like transmission towers, structures on expansive soils etc. for a very long time, however it is only in the last 30 years that dynamic response of a pile has been studied. Evaluation of dynamic soil-pile interaction is a very complex problem as the conditions and properties of soil are highly variable and unpredictable. Various models and approaches have been suggested by various investigators for evaluating the dynamic soil-pile interaction problem, but most of them are based on the assumptions that the behaviour of soil is linear and the soil surrounding the pile is strongly adhered to it. But in practice, it is not so. The soil surrounding the pile is always somewhat loosened and undergoes some deformation when a sinusoidal load is applied. This causes the soil-pile system to behave nonlinearly.In earlier studies by Novak, (1974), Novak and Aboul-Ella, (1978) etc. a linear elastic behaviour of soil was assumed. This approach was very useful in understanding the mechanism of soil-pile interaction to a large extent. Subsequently various models were suggested like the lumped mass models with nonlinear discrete springs, dashpots and friction elements Matlock et al. (1978), weak cylindrical zone around the pile model Novak and Sheta, (1980), ideal boundary zone model with non-reflective interface, Han and Sabin, (1995) etc. These approximate solutions give an idea about the mechanism of dynamic pile-soil interaction to a large extent. However, in reality both separation and slippage can occur due to the formation of a weak bond at the contact surface between the soil and the pile when a dynamic load is applied. In addition, the soil column adjacent to the pile experiences large deformations under dynamic loads and thus behaves nonlinearly.Some computer aided model studies on the dynamic response of under-reamed piles have been reported, however, very few insitu dynamic tests on under-reamed piles are reported. Dynamic tests on piles were carried out by Novak and Grigg (1976) on small scale single piles and pile groups in the field. Similar field tests on small scale piles were conducted to study the nonlinear behaviour of a single pile and a pile group under strong harmonic excitation by Han and Novak (1988), Han and Vaziri (1992), Burr et al. (1997), Manna and Baidya (2010) etc. The majority of these experimental studies were focussed on the response of the specific pile groups and compared with the results of a single pile. Hence there was a need to study the influence of pile g"

Jan 1, 2015

By E. L. Garton

The United Status Bureau of Mines has recently collected samples of crude petroleum from well] in the newly developed Joiner, Kilgore, and Longview fields of Rusk and Gregg Counties in the East Texas district, and from the Van field of the East Central district of Texas. East Texas Cruder The four samples of crude oil from the East Texas fields are all typical "intermediate base" crudes according to the classification given by Smith and Lane. 3 Sample 31,063 is from the discovery well in the Joiner field. This well came in on October 3, 1930, with an initial production of 400 barrels per day. Sample 31,062 was obtained from a well that was completed on February 1, 1931, with an initial production of 3,500 barrels per day. The 32 East Texas crudes are produced at an average depth of approximately 3,600 feet. which is the deepest Woodgine-sand production so far encountered in any of the Texas or Louisiana fields.

Jan 1, 1931

By R. Lapcevic, P. Lokin

"Among other components, ore body „T“ was discovered in the Bor pit copper mine at a depth of app. 500m. The ore body is relatively small: 60-65m long, 40-45m wide and up to 50m high, but with an extremely high content of copper and accompanying metals. The rock mass containing the ore body is composed of altered andesite of relatively poor physical-mechanical characteristics. The exploitation of this ore body by way of conventional mining methods was associated with high risk, cost, and potential losses of the rich ore. Due to everything specified hereinbefore, the adopted solution involved ore exploitation with complete ensuring of excavation stability, thus forming an extremely large underground opening. The excavation and supporting were performed according to the NATM principles along with applying shotcrete, 9-25 m long cables, and horizontal and vertical lattice girders. The excavation of the ore body was completed in app. 2.5 years, all the while ensuring complete stability and security of people and equipment; construction works were constantly monitored. The proposed solution for ore excavation enabled more than 95% exploitation of ore as requested by the Investor, while depletion due to waste-rock excavation was less than the allowed 5%. INTRODUCTIONThe Bor copper deposit is located in Eastern Serbia. Copper exploitation in Bor commenced as far back as 1902. A total of 26 ore bodies varying in size and valuable mineral content have been excavated so far. One of the most recent excavated ore bodies is ore body „T“, which is one of the smallest bodies by volume, but also a body with one of the largest content of copper and accompanying metals. An important fact regarding its exploitation is that it is located at a depth of app. 500 m; that its shape is irregular: 60-65 m long; 40-45 m wide and app. 50 m high; and that it lays within a rock mass of relatively poor physical-mechanical characteristics. In addition, above it, in its immediate vicinity, ore body „F“ was previously excavated and its room was refilled with backfill and water. Excavation methods common in mining practice (excavation with caving, excavation with backfilling, excavation with protective pillars) were inadequate in this case for various reasons:• The immediate vicinity of the previous ore body „F“ room could cause expansion of the caving zone also to that room, along with penetration of groundwater and flotation sludge;• Possibility of deformation expansion caused by caving as far up as the surface of the terrain, including the urban area;• Difficulties in maintaining the stability of excavation sidewalls having steep slopes and great height;• Significant loss of ore mass with a relatively high content of metals etc."

Jan 1, 2015

By A. A. Bauer, H. A. Saller, F. A. Rough, J. R. Doig

among uranium alloy systems are the U-Zr, U-Ti,and U-Mo binary systems, in that an intermediate phase, of limited solubility range, exists in each system. These intermediate phase alloys offer a promising field of investigation, both as binary alloys and as ternary alloy combinations. While a limited amount of work has been done on the binary alloys, none has been done on ternary combinations of these alloys. As a possible prelude to more intensive investigation of these systems, a study of the phase relationships between the 6 phases of the U-Zr and U-Ti systems was undertaken. The solid-state portions of the binary constitutional diagrams for the U-Ti,1 Zr-Ti,2 and U-Zr3 systems are shown in Fig. 1. The solid to liquid transformations are not shown, as these transformations were not studied in the ternary system. The phase designations employed are based upon those shown in the uranium constitutional diagrams. The crystal structures of the various phases are given in Table I. Experimental Materials and Methods The ternary section presented is based upon the results of thermal, metallographic, and X-ray analyses of a series of alloys ranging in composition between the phases of the U-Zr and U-Ti systems (U-74 atomic pct Zr to U-35 atomic pct Ti). After preparation of the alloys, thermal data were obtained. On the basis of these data, specimens were heat treated and examined metallographically. Specimens were then selected from those heat treated for X-ray determination of the phases present in what were considered critical phase regions. Alloy and Specimen Preparation—Alloys for this investigation were prepared from selected as-reduced uranium and crystal-bar zirconium and titanium. For nominal compositions, see Table 11. Charges were arc melted from five to seven times under a helium atmosphere, finally being cast into wire-bar form for fabrication. A zirconium getter button was used to clean the furnace atmosphere prior to melting. The alloys were homogenized 20 hr at 900 °C and furnace cooled. A portion of each bar was then removed for thermal analysis; the remainder was saved for fabrication. Alloys 8 through 14 were placed in steel tubes along with zirconium getter chips and, after flushing with argon, the tubes were welded shut and rolled at 1500 °F to a 50 pct reduction in diam. The remaining alloys were annealed 24 hr at ll00°F to insure transformation of the ? phase to the 8-U2Ti phase and were then hot rolled from a salt bath. Attempts to roll alloys 6 and 7 at 1100 °F were unsuccessful. Following this, attempts were made to roll pieces of alloys 1 through 5, which had cracked rather severely during casting, at 1200 °F, but these efforts were also unsuccessful. These alloys were, therefore, further treated in their cast and homogenized condition. All alloys were pickled to remove oxide formed during rolling. Thermal data were obtained on these alloys by conventional differential thermal analysis at a heating rate of 30C per min, and by a high-speed heating method at rates of approximately 10°C per sec. For the latter method of analysis, a 36-gage Chromel-Alumel thermocouple is spot welded between two slivers of alloy, the sandwich being en-

Jan 1, 1958

Projections of metal requirements for Japan and the United States indicate growing competit- ion for Australia's mineral output and a critical need for continuing discovery of new reserves. These projections may be modified by economic, social and political controls - the most import- ant factor probably being a shortage and the high cost of risk and development capital. Changing ownership patterns toward joint ventures and increased state participation are anticipated. New developments in global tectonics and metallogeny delineate favourable zones for ex- ploration and permit establishment of priority search areas even in regions of poorly known geology. Declining ore grades and special character- istics to meet technological requirements may modify identification and evaluation criteria. A broad approach considering all environments of concentration within the geochemical cycle is re- quired within any metallogenic province. The exploration geologist must be able to integrate geological theory, mining technology and financial analysis to establish well defined exploration objectives, in terms of economic and geologic models, in concept-oriented programmes.

Jan 1, 1973

By Robert Schnab

ASFINAG is responsible for the construction and operation of the Austrian highway system. It is approx. 2,400 km of highways and 65 tunnels with a total length of 200 km including the Tauern Tunnel. In order to improve the documentation of the tunnel construction, ASFINAG chose to use a state of the art tunnel scanning system to record the various stages of construction: excavation, initial shotcrete lining, smoothing layer and final cast in place concrete lining. The geometric and photogrammetric documentation is provided on a daily basis to all par-ties involved. This innovative concept provides accurate & complete information in real time. The tunnel scanner documentation of the 2nd tube at the 6.4 km long Tauern Tunnel will be presented in this paper as a part of the survey contract.

By William H. Emmons

Jan 1, 1912

By Bryan M. Maybee

The scheduling of underground mining activities is a complex task, in particular because of the requirement to satisfy a large number of constraints. A Schedule Optimization Tool (SOT) for underground mine planning is described, and its use for investigating strategic decisions is illustrated by means of a case study. The main components of SOT include: a genetic algorithm, which searches for optimal schedules; guidance, the application of heuristic rules to guide the genetic algorithm; and sliding, which implements just-in-time development. For the case study, SOT is employed to generate schedules at various ore capacities, accounting for the appropriate financials in each schedule evaluation. The case study finds that preliminary scheduling performed before invoking SOT, intended to provide a good starting point for the search, does not ultimately lead to higher value schedules. Two key uses for SOT are identified. A mine planner can save time by using SOT to produce high-value scheduling alternatives. This process ensures a broader investigation of the value that the deposit can yield. Also, SOT can be used to validate strategic and tactical decisions, by scheduling under alternative scenarios. Both uses produce high value schedules conforming to all imposed resource constraints.

May 1, 2009

By Merwin RA

The recent development of rare earth permanent magnets has revolutionised the field of magnetic separation. The advent of rare earth permanent magnets in the 1980s provided a magnetic energy product an order of magnitude greater than that of conventional ferrite magnets. This has allowed the design of high-intensity magnetic circuits operating energy free and surpassing the strength and effectiveness of electromagnets. New applications and design concepts focusing on the mineral and metal processing industries have evolved. This technology also led to the development of various magnetic separators specifically designed for mineral processing applications. Applications which were not previously considered are now being applied to primary mineral upgrading and recycling and secondary recovery.

Jan 1, 1993

By Alessandro Navarra, Kristian Waters

Mineral concentrators are designed from preliminary geological data, and are therefore subject to geological uncertainty. This uncertainty has a demonstrable impact on the mining lifecycle, and has motivated stochastic strategic mine planning algorithms. The current paper describes how these algorithms may be extended to consider mineral processing operations in conjunction with open-pit mining operations. In particular, the paper describes an effective way to incorporate variable concentrator feed grade into these algorithms, which is the first step toward more elaborate representations of mineral concentrators. The resulting framework will be able to connect geological data to alternate configurations of the downstream resources, hence comparing the benefit of each configuration, and the corresponding capital investments. Sample computations are presented, comparing the NPV and utilization for several different mineral processing capacities.

Jan 1, 2015

By David E. Emerson

The Bureau of Mines has developed a mass spectrometer method for deter-mining the helium-3 content of high-purity helium. The work was performed to evaluate experimental methods for removing helium-3 from high-purity helium and to better determine the composition of pure helium used in research. This was accomplished by increasing the inlet sample pressure, ionizing current, and amplification of the current produced by the ions collected on a conventional mass spectrometer that had been modified. With these modifications, the helium-3 content was determined in the parts-per-million and parts-per-billion range in helium-4.

Jan 1, 1976

By John E. Gale

Seven, 15 cm diameter, cores of gneissic granite, four containing induced fractures and three containing natural fractures all oriented normal to the core axis, were tested in an uniaxial compression mode over a range of 0 to 30 MPa. At given normal stress increments, over two or three loading and unloading cycles, the flowrates and changes in fracture aperture were measured. The induced fractures gave lower initial (at low stresses) and lower final flowrates (at maximum stress) than the natural fractures. Both types of fracture exhibited permanent fracture deformation between loading cycles as well as highly nonlinear, with distinct hystersis, loading and unloading flowrate-stress curves. A significant finding of this stud is the breakdown of the cubic law for fracture flow in induced fractures subjected to normal stresses greater than 20 MPa, with the breakdown occuring at much lower stresses in natural fractures.

Jan 1, 1982

By Raj P. Singh

Applications of cementation in the recovery of metal ions from process solutions have been known for a long time. Cementation reactions involve electrochemical precipitation of a noble metal from solutions of its salts on a more electropositive metal which, in tum, progressively dissolves. For example, addition of zinc metal powder in a solution containing zinc and cobalt ions would allow for the precipitation (separation) of cobalt according to the following chemical reaction. This paper pertains to the recovery of cobalt from cobalt process solutions via a cementation reaction on aluminum shavings (metal scraps from cans etc). Specifically, we report on the characterization of cobalt process solutions, a by-product obtained from cobalt chemicals, and the kinetics of cobalt, nickel and manganese cementation from process solutions on aluminum shavings.

Jan 1, 2000

By R. J. Quigg, G. S. Doble

Commercial stress -relieved TD Nickel bar was shown to retain room- and elevated-temperature tensile strength after exposure up to 2501°F. Cold swaging increased both room -temperature and 2000°F tensile strength. After annealing at 2500°F the strengthening due to swaging was retained at 2000°F hilt eliminated at room temperature. Annealing produced changes in hardness and X-ray half peak width indicating the presence of recovery processes as 1071° as 1000°F but no recrystallization of swaged material was noted at any temperature. In contrast to swaging, rolling induced a recrystal-lized structure after annealing. The tensile strength of this recrystallized structure was comparable to the cold-worked condition. High-temperature tensile properties of as -received bar were highly anisotropic with the transverse tensile strength being one fifth the longitudinal value. The aniso-/ropy is affected by working direction and may he partially reversed by changing the direction of metal flow. The divergence in tensile strength, beginning above 550°F or- approximate one third the absolute melting point, is strain-rate dependent. T D Nickel is a commercial dispersion-hardened alloy containing 2 vol pct thoria. The dispersion, consisting of spherical particles 0.030 to 0.050 in diameter with an interparticle spacing of less than 1 is reported to maintain stable properties up to 2400°F.1 This stability of second phase results in maintenance of elevated-temperature strength at higher temperatures and longer times than normal nickel-base superalloys.2 The purpose of this paper is to describe the effect of various mechanical working operations on the strength and microstructural stability of TD Nickel bar. MATERIAL AND PROCEDURES All material used in this study was commercial TD Nickel bar. This material is produced by a chemical process which results in a nickel powder containing a dispersion of thoria particles. The powder is then pressed, sintered, extruded, and subsequently worked to bar stock. Three starting materials from three separate lots were used: as-extruded bar. 1-in.-diam stress-relieved bar, and 1/2-in.-diam stress-relieved bar. Since TD Nickel bar stock is cold-worked without a recrystalliza-tion anneal, the accumulated deformation or degree of cold work in these materials increases as the bar diameter decreases. Some of the 1/2-in.-diam bar was swaged to 1/4 in. diameter at room temperature in order to produce an as-worked condition for comparison with the stress-relieved stock. Tensile testing was performed on an Instron Tensile Tester at a constant crosshead speed of 0.020 in. per min. The 0.2 pct offset yield strength was measured from the load-crosshead movement plot. Specimen gage dimensions were 0.080 in. in diameter by 0.40 in. in length, producing a strain rate of approximately 0.050 min-1. Specimens were tested in air and heated within a resistance-wound furnace controlled to ±5°F. A 15-min soak at temperature was employed before testing. Samples were heat-treated in air and specimens machined after exposure with sufficient material removed to eliminate any surface contamination. X-ray line breadth was determined from a diffractometer scan of a transverse face of a bar using copper K, radiation. Metallographic preparation utilized standard mechanical polishing with Carapella's etch. Specimens for electron microscopy were electropolished in a 1:7 sulfuric/methaol solution and chromium-shadowed collodion replicas prepared. RESULTS AND DISCUSSION I) Effect of Elevated-Temperature Exposure on the properties of TD Nickel. The effect of various elevated-temperature exposures on the room-temperature tensile strength of TD Nickel is shown in Table I. In the unexposed condition the tensile strength, reduction in area, and hardness all increase with increasing accumulated deformation while the elongation decreases. After exposure at 2500°F the strength of all three materials decreases to about 65,000 psi and the elongations increase slightly. The apparent increase in strength of the 1-in. bar after a 2000°F treatment is probably experimental scatter. These results indicate that the room-temperature strengthening due to additional deformation is annealed out upon elevated-temperature exposure. In contrast to the room-temperature data, the 2000°F tensile strengths increase in order of increasing deformation even after exposure. Although some loss of strength occurs after exposure, much of the effect of working is still maintained at 2000°F. The room-temperature hardness after various

Jan 1, 1965

By D. M. Hausen

A computer program has been developed by Newmont Exploration to convert mineralogic data by XRD into rock type and ore type classifications. This method has proven useful in identifying lithology from cuttings samples, where percussion drilling was an alternative to expensive core drilling. Computer printouts of rock type and ore type identifications can be generated simultaneously with mineralogic analyses, resulting in a considerable time savings in manual calculation. XRD-computer logging was first applied to the Carlin mine in north central Nevada, and later to the Maggie Creek and Gold Quarry gold deposits, southeast of the Carlin mine. Impure Paleozoic limestones of the "lower plate" Roberts Mountain Formation and the "upper plate" transitional facies have been decarbonatized to altered siltstones and shaley units along vertical faults and permeable stratiform horizons. Advanced stages of decarbonatization were accompanied by silicification. Quantitative XRD data are initially sorted into principal rock type units (limestones, siltstones, dolostones, shales) based on major mineralogic components (calcite, quartz, dolomite, clays). On the basis of relative amounts of less major constituents, descriptive subclassifications (dolomitic limestones, dolomitic siltstones, argillaceous cherts) are made. XRD lithologic data provide assistance in correlating lithologic units, and delineating favorable replacement horizons associated with gold mineralization.

Jan 1, 1982