Search Documents

By W P. Player

The legislative operating environment, or the mineral regime, that a country has to offer is one of the key determinants that a company wanting to invest in an area takes into account in formulating its investment decision.   The New Zealand Government recognises this and the importance of getting the regime right in order to provide for continuing investment in mineral exploration and mining in New Zealand . In recent years, the Government has given considerable attention to developing legislation which provides for investment to take place; for those making the investments to have a stable, fair and open investment environment with government intervention only when considered absolutely necessary because other approaches are not working; and for the people of New Zealand to know that investment must meet acceptable health and safety standards and have acceptable impact on the environment. Also of key importance is having a clearly defined mining regime which includes rules on how to obtain a permit and rules in respect of ongoing permit compliance, rights to develop a mineral resource and permit conditions (in particular, the royalty regime). In New Zealand , these matters will all be addressed in what are referred to as 'minerals programmes'.   The Crown Minerals Act 1991, which is the legislation governing the allocation and management of permits for Crown owned minerals, requires that the Minister of Energy prepare minerals programmes. Minerals programmes establish the policies, procedures and provisions that the Minister shall follow in exercising his or her functions and powers under the Crown Minerals Act. Minerals programmes set out the principal reasons for and against adopting these policies, procedures and provisions and also restrictions on prospecting, exploration and mining for Crown owned minerals. Essentially minerals programmes define the mining regime for the minerals to which they apply, other than the taxation regime, environmental and health, safety provisions, land access matters and general matters concerning the investment climate.

Jan 1, 1995

By George F. Weaton

During the past eight years there has been a dramatic change in the iron ore industry of Minnesota, in that its status has changed from that of a seller's market to a higly competitive buyer's market. Minnesota's natural ores must now be beneficiated and up-graded considerably to be marketed in order to compete with the higher grade foreign ores as well as with the locally produced and highly desirable taconite pellets. With the passage of the "Taconite Amendment' in the November, 1964 election, the taconite industry commenced to expand in Minnesota, which, although initiated in that state, was benefiting many other states and some foreign countries to a much greater extent than Minnesota. These other areas were actually appropriating markets that had been established and retained by Minnesota for many years. Since the approval by the state voters of this amendment, there has been a great increase in the development of taconite properties on the Mesabi Range.

Jan 1, 1966

By John O. Marsden

Technology development and innovation has played a crucial role in the copper industry throughout history. The effective development and implementation of new technologies allows mankind to produce copper at progressively lower cost of production at a given feed grade and mineral type. This progress serves to counteract cost escalation over time and, depending on the magnitude of the cost benefit, allows ore cut off grades to be reduced thereby improving the availability, accessibility and utilization of mineral resources. The development of step change technologies that can offer >$0.15/lb total cost benefits provides a significant opportunity for producers to achieve competitive advantage, but it has been argued that rapid dissemination of technology makes such competitive advantage unsustainable over time. This paper presents the results of a recent study that evaluates a number of historical and emerging step change technology case studies in the copper industry and quantifies the associated cost benefits for users, the impact on the production cost curve, and the duration of such cost benefits for various categories of implementers: first mover, fast follower, conservative followers and laggards. The results provide a compelling case for major, mid-tier and emerging copper producers to invest in technology development initiatives if they wish to achieve and sustain competitive advantage over the long term. INTRODUCTION AND BACKGROUND A key issue for mining companies is how much time, effort and cost to spend on research and technology development (R&TD). The economic drivers for technology development and implementation are poorly understood in our industry and the business case is clouded by some notable and well-publicized failures (McNulty, 1998). Mining companies are in business to deliver financial returns to investors. This means delivering short term results on a quarter-by-quarter reporting basis as well as sustaining and growing the company to retain and reward a sustainable longer term investor base. The cyclical nature of the commodity metal markets makes it challenging to maintain investment in research and step change technology development: Mining companies must manage through the highs and the lows of price cycles, typically ranging from 5-15 years in length. The discounted cash flow approach to investment evaluation results in weak financial justification for R&TD expenditures. A clear and compelling rationale to support longer term investment in research and step change technology implementation is required.

Jan 1, 2019

By A. T. Iannacchione

Unfortunately from 1991 through 1995, 44 miners were fatally injured in the stone industry. Of these 12 occurred at underground mines from a total work force of less than 2,000 miners. Nine of these 12 miners were fatally injured in falls of roof or rib. A safer environment for the miners can be achieved by evaluating the nature of the hazardous ground and by developing more efficient and effective ground control strategies. Roof and rib conditions in the underground stone industry were observed and assessed at 33 mines in Illinois, Indiana, Kentucky, Maryland, Missouri, Pennsylvania, and West Virginia (Figure 1). Hazard assessment indicated that those ground failures occurring under moderate to substantial overburden ( > 30 m [100 ft]) were caused by stress concentrations and geologic structures. Ground failures near the surface are caused by solution (water) processes. Selection of the mining horizon and mine layout decisions tremendously influence ground stability.

Jan 1, 1997

By G. Sedelnikova, D. Kim, N. Ibragimova

"The object of this study was three samples of sulfide old tailings, which were obtained after Cu- Zn ores processing. Fine metal dissemination in sulfides as well as fine mineral intergrowth determine the refractory nature of material and low metal extraction using simple methods: gravitation 1-6%, flotation 32-48%, cyanidation 10-37%, and cause the need to use sulfide bio-oxidation to liberate gold and to recover it by heap leaching. The gold is the main valuable metal in the tailings with content 1-1.5 g/t. Heap bio-oxidation with mesophilic and moderately thermophilic bacteria was used for pre-treatment of tailings before gold heap leaching from bio-oxidation solid residues. The tailings have a low permeability < 0.3-1.2 m/day, which is caused by migration of fine particles, decreases recovery rates, and is poorly suited to heap bacterial leaching. Therefore, preliminary gold sulfide tailings with permeability < 0.3 m/day were pelletized using copper containing flotation tailings of converter slags and calcium oxide. The most gold extraction was obtained for pelletized tailings. The base metals (copper and zinc) were precipitated from bacterial solutions. Experiments have demonstrated effective bio-oxidation of all third gold sulfide tailings samples and enough high gold extraction 60-82%.INTRODUCTIONIn Russia, as everywhere, there is a trend toward deterioration in the quality of mineral resources, including non-ferrous and precious metals, manifested in lower grade and higher complexity of ores. The proportion of refractory ores is increasing, characterized by fine dissemination of metals in sulfides, intergrowth, and poor liberation of minerals during concentration, resulting in loss of base and precious metals to flotation tailings.Over the operation period, huge reserves (hundreds of million tons) of ore processing waste have been accumulated at mining and concentration operations. Because of the imperfections of the previously used ore concentration technologies, the content of precious and base metals in flotation tailings is comparable with the grades of the ores being currently processed. Therefore, old tailings can be viewed as an additional reserve of non-ferrous and precious metals. The works (DEN, 1997; Lyman, Johnson, & Guerney, 2000) demonstrate that, tailings containing sulfides (sulfur, copper, zinc, and other metals) are a potential environmental hazard since they produce acid drainage water containing toxic components. Processing those tailings would require designing an effective technology for recovering useful components and protecting the environment."

Jan 1, 2016

By Jacques F. Abrahamse, Kevin A. Bahe, T. Arthur Palm, Gregory E. McCluskey, Stephen L. Bessinger

Introduction Basis For System San Juan Coal Company (SJCC) is a subsidiary of BHP Billiton. Until recently, BHP Billiton operated three surface mines in northwestern New Mexico: Navajo, San Juan, and La Plata. The San Juan and La Plata Mines supplied the San Juan Generating Station operated by Public Service of New Mexico. Stripping ratios at those operations were increasing, and by 2000 a feasibility study was underway to develop SJCC’s vast underground reserves as a replacement. Early in the evaluation and planning phase for the San Juan Underground Mine, it was determined that the target seams (Fruitland #8 and #9) had a high propensity for spontaneous combustion. Spontaneous combustion was identified as a risk, both to personnel and equipment, and to the ability of SJCC to reliably fulfill its obligation to the power plant. In the last 20 years, several western US coal mines suffered underground spontaneous combustion events and/or mine fires. Included in this group were Colorado Westmoreland’s Orchard Valley Mine (1987), RAG’s Willow Creek Mine (1998 and 2000), Oxbow’s Sanborn Creek Mine (1999), the West Elk Mine of Arch Coal (2000), Arch’s Skyline Mine (2002), Western Fuels’ Deserado Mine (1996), and the West Ridge Mine of Andalex Resources (2003). The cause for the majority of these fires was spontaneous combustion. Fighting the fires required injection of an inert gas or foam. Nitrogen and carbon dioxide were the predominant choices of inert gas. In all cases, the gasses had to be trucked in from considerable distances. Before the inert gas could be used, injection holes had to be drilled into or near the suspected fire locations. This drilling and trucking caused costly delays in the timing of the fire fighting effort, and was not as precise as desirable. Emergency purchasing of gas and pumping services was extremely expensive, running as high as $70,000 per day at one mine. As a result of the experience of other western US coal operators, and the risk inherent with spontaneous combustion at SJCC, it was decided to pursue installation of a nitrogen delivery facility on-site at SJCC. This decision was later expanded to include a continuous supply of nitrogen.

Jan 1, 2005

By Innes J. A

The structural variations occurring in pellets of finely divided mixtures of iron ore and coke breeze, metallized by firing at elevated temperatures, have been examined microscopically. For any given pellet composition, time and temperature are the two most important factors in determining the development of the bonding processes.INTRODUCTIONThe success of sintering and pelletizing processes in the agglomeration of fine iron ores for blast furnace use has brought about rapid changes in thinking relative to methods of preparing furnace burdens. Increases in productivity with the use of sinter emphasize the advantages of a stable, uniformly sized furnace feed. Current practice is to produce a self-fluxing sinter containing most of the lime requirements of the furnace incorporated as a stable medium (Figgis and Charker, 1962). The elimination of fine material from the burden allows greater stack permeability and smoother operation.Sintering and pelletizing of iron ores with or without the incorporation of fluxing compounds has conditioned operators to the extent that it is now considered possible that all components of the burden may eventually be beneficiated in one form or another. Investigations are in hand to improve the quality and sizing of coke, which occupies the major part of the burden volume (Callcott, Innes and Brown, 1961; Innes, Gregory and Worner, 1963). Interest is also being revived in methods of pre-reducing iron ores prior to charging to the furnace (Hansen, Melcher and Fine, 1961). Recent experiments in a small experimental blast furnace (Melcher, 1963) show that charging of semi-metallized pellets can give rise to a production increase of 55 per cent...

Jan 1, 1963

The objective in control blasting is to reduce overbreak to control the final pit wall slope, shaft, drift, ditch, bench, etc. to the final planned excavation limit.

Jan 1, 1990

By O. Dojcar

The results of a laboratory investigation of rock fragmentation conducted with a model material were partially verified under field conditions. The object of the investigation was to study the qualitative and quantitative relations between the parameters of the primary blast and fragmentation to enable the planning of an economically efficient degree of disintegration with optimum utilisation of the blast energy. The three blast parameters that were considered were burden, specific charge and the ratio of spacing to burden

Jan 1, 1991

By Nóra Schreithofer, Zoltán Jávor, Kari Heiskanen

"One of the challenges the mineral processing industry is facing is caused by the fact that water resources in mining areas are becoming very limited and the cost of water is increasing. The water sources in arid regions often have high salt content. Environmental regulations are forcing plant operations towards completely closing the water cycles within plants. This means that impurities (salts, reagents, ions dissolved from minerals, etc.) accumulate within the circuit that will affect the flotation performance. Water purification can significantly increase the operating costs therefore it should be carefully considered weather the impurities need to be completely removed or is there a tolerable level of impurities that can still be left in the process water without significant deterioration of the flotation performance? Several additional questions arise: what are the tools that help identify what is a tolerable level of impurities? How do the different impurities interact and what is their effect on the process? The effect of frothers on the dynamic properties of air/liquid interface in different size-scales has been extensively studied by the authors in the past. Based on these studies a frother characterization framework was developed that systematically examines the dynamic surface properties of the air/liquid interface in relation to the bubble size. This work can be considered as tool that could be used for the above mentioned purpose. The present study investigates weather the same frother characterization framework can be applied for systems where both frother and different types of salts are present. Nasfroth 240 was used as a frother, in combination with structure-breaker KCl or structure-maker NaCl and CaCl2. Bubble size measurements in laboratory scale mechanical flotation cell and laboratory flotation column and dynamic surface property measurements (dynamic surface tension and dilatational elasticity) were performed. The results highlighted the addition of salt to the frother solutions significantly decrease the bubble size and increase the froth high. The coalescence behavior of bubbles showed correlation between the D32 and ionic strength of salts. The results highlighted that the studied structure maker and structure breaker salts effect the dynamic surface properties in different way."

Jan 1, 2014

By Jean-Louis Briaud

The following is a summary of a very recent report prepared at Texas A&M University for the National Cooperative Highway Research Program and entitled "Downdrag on Bitumen Coated Piles". Anytime the soil settles more than the pile, downdrag or negative skin friction will develop. The load in the pile increases with depth up to a certain point and then decreases down to the pile point. This phenomenon has been quoted as being the number one culprit for deep foundation failures. In Chapter 1, an introduction to downdrag is given. The most common criterion for downdrag is to consider it in design as soon as the settlement of the soil surface after pile driving exceeds 0.5 in. Coating piles with bitumen is an effective way of reducing downdrag forces and therefore allows to use smaller piles for the same load. This results in cost savings. Coating piles with bitumen increase the cost of piles by about 33% and therefore the decision to use bitumen is generally based on economic considerations.

Jan 1, 1989

By Carle R. Hayward

THOUGH recent months have seen a rapid decline in lead-smelting activity and consequent uncertainty as to the future, the first half of the year showed progress in keeping with similar activity in other metals. Demand for scrap increased and various lead-bearing materials found their way to plants producing secondary lead. Some of these materials introduced complications into normal smelting procedure and were the cause of many conferences among plant officials attempting to find the most satisfactory method of treatment. If a blast furnace is to do itself justice it must be run with an open charge. Troubles inevitably result when materials are added to a charge which tighten it up and pre- vent free burning of the coke and con- sequent rapid smelting with a clean hearth This fact has long been recognized by plants producing primary lead, but only recently only it received the attention it deserves.

Jan 1, 1938

By Toshiaki Nakai, Kunihiko Takeda, Kimio Imaizumi, Hiroaki Shirasaka

"The new type of nano-porous silica particle was considered to be constructed by the spinodal decomposition-type process which was found to have narrower pores than those of conventional porous silica prepared from boron silicate or ""Shirasu"" balloon. Nano-porous silica particles were fabricated by the calcination of silica gel mixed with well-dispersed complex salts composed of phosphorous and molybdenum compounds. Both silica and inorganic salts were not perfectly dissolved in the suspension solution. After removing of the water, the silica-inorganic salts complex was volatized and successively calcinated at a temperature ranging from 650 °C to 800 °C. Then, the inorganic salts were removed by dissolving in hot water. Other inorganic salts such as potassium halides were also found to be effective as a pore-size controller.IntroductionControl of structure has an important role in the field of industry as well as in the separation and purification technology for metals and organic syntheses. Many studies on the control of material structures have been reported regarding porous materials with pores ranging from nanometer to micrometer scale. 1 ) One example is zeolite as a naturally yielded porous inorganic material. Various types of synthetic zeolites have been studied as ""molecular sieve"" materials with ordinary pore-size of less than one nanometer. In 1992, crystalline meso-porous material with a large surface area named MCM-41 was synthesized through the use of template synthesis. 2) In direct relation to our study, amorphous borate glass having 4 to 100 nm of fine pores known as Corning glass 3l or SiO2-Al2OrB2O 3-CaO porous glass having large pore dispersity ranging from 4 to 10,000 nm have been reported. 4 ) S) 6 ) Some examples of several reported studies are as follows: phase-separated porous glass consisting of B2OrAl2O3-ZrO2-RO-R2O complex oxide 7 ) glass with finer pore induced from hydrolysis of silane alkoxide, porous material attained by condensation polymerization through the use of sol-gel process 8), alumina meso-porous material 9 ) 10), silica-zirconia material 11), carbon porous material 12), etc.."

Jan 1, 2000

By Norbert Patzelt

The high-pressure grinding roll was introduced about 10 years ago and has established itself in many applications. Most of these machines are used in grinding circuits in the cement industry. A few operate in conventional mineral-processing plants. Polysius has sold more than 350 Polycoms worldwide. An exception is diamond-ore processing in South Africa and Australia. This type of grinding system increases diamond liberation and reduces the capital costs for the downstream processing plant. There are several reasons why high-pressure grinding rolls have not been used more extensively in the mining industry: - The mining industry adheres to conventional grinding technology and regional preference for certain comminution circuits. - Design, scale-up and flowsheet assessment procedures are viewed as being immature and reduce confidence in the potential application of the technology. - Downstream process benefits are unproven on a plant scale.

Jan 1, 1995

By B. Yamamoto, D. Post, J. De Leon, A. Meike

"This paper describes the theory, design, building, and testing of the passive magnetic bearing stabilizing system which is the core of the passive magnetic bearing system. The stabilizing system is made up of two large magnetic disks opposing themselves with a stabilizing disk in the center which allows the system to self-locate in a null position without the need for external power sources or sensors. When outside forces act upon the stabilizer, the magnetic fields interact with the stabilizing plate to return the system to its null position. Collaboration between two industry leaders has allowed an actual prototype to be built and tested providing real data to prove out the theory.INTRODUCTIONMagnetic bearing/stabilizer systems have many advantages over conventional mechanical bearing systems. These include near-zero drag losses and no need for lubrication since the rotating elements make no mechanical contact with the stationary elements of the bearing system. However all magnetic bearing systems must contend with a constraint known as Earnshaw’s Theorem in the early 1800’s, this theorem asserts the impossibility of constructing a stable, non-contacting, electrostatic or magnetostatic levitation system using only fixed charges or fixed magnetic poles, such as those produced by permanent magnets. Because of the constraint imposed by Earnshaw’s Theorem virtually all present-day commercial magnetic bearing systems are of the “active” type. That is, they employ electromagnets that are powered by amplifiers the inputs to which come from sensors embedded in the bearing system. These sensors are a part of a feedback loop that operates to keep the levitated rotating parts of the bearing stable and centered. The resulting complexity means that active magnetic bearings are expensive, require periodic maintenance, and continuously consume electrical power to energize their amplifiers and their electromagnets.Passive magnetic bearings are, of course, also subject to the constraints imposed by Earnshaw’s Theorem but they solve this problem in a straightforward and simple way, with only “passive” elements that take advantage of a loophole implicit in the derivation of Earnshaw’s Theorem. This loophole is that Earnshaw’s Theorem as derived applies only to static systems, i.e. an assembly of stationary permanent magnets arranged so as to levitate an object containing other permanent magnets. The theorem can be overcome if dynamic effects are taken into account. In active magnetic bearings the “dynamic effects” involve the afore-mentioned sensors, amplifiers, and electromagnets."

Jan 1, 2012

By S. Suzuki, Y. Maeda, N. Wakamatsu

"A new pyrometallugical technology, named KLS process, has been developed by Dowa Mining at its Kosaka Smelter to smelt various kinds of lead raw materials.The process consists of clearly separated two reaction steps, smelting and reduction. For this purpose, respective stationary furnaces are installed which are connected by a slag launder.Dry raw materials, together with pulverized coal and oxygen-enriched air, are injected through a lance pipe into the molten slag in the first furnace. It is kept under a high oxygen potential to remove sulfur completely. Resultant PbO rich slag overflows to the second furnace where pulverized coal and insufficient air are also injected through a lance pipe to reduce PbO to lead bullion and to compensate for thermal deficit. The entire operation is carried out continuously. The process development started back in 1981. In late 1986, a pilot plant with a capacity of 3.5t/H was constructed.Already nearly 20,000 tons of raw materials, mostly lead sulfate mixtures have been smelted successfully.IntroductionFor a long time, main raw materials for lead smelting at Kosaka smelter have been such secondary incombustibles as lead sulfate and lead-barium sulfate. The former is leach residue of the copper smelter flue dust and the latter originates from Iijima zinc refinery. While the most of lead concentrates produced locally has been smelted by an ISF of Hachinohe smelter in which Dowa Mining has a share.The surplus lead concentrates were processed at Kosaka by a hydrometallurgical method to convert PbS to PbSO 4 as pretreatment, and followed by simultaneous smelting together with the above secondary materials (1). Approximate output has been 1,5000 /M of lead bullion and slightly more than 2,000t/M of refined lead by adding lead bullion returned back from Hachinohe smelter (2)."

Jan 1, 1988

By R J. Nicholson, J M. F Clout

As part of an overall strategy to make significant new technological advances for the sustainability of the mineral processing and related process industries CSIRO Minerals has developed a new dry separation device. It represents a technology breakthrough and has the potential to radically change the way in which dry particle size classification is achieved in the minerals industry. Conventional dry separation techniques have limited applications and often suffer from low productivity, high operating costs, low separation efficiency, the need for dust control and a lack of flexibility. In the absence of efficient dry techniques, wet processing is often used. The use of wet processing either requires the introduction of water into a separation process, which causes environmental concerns through the need for water supply and tailings dams or the use of æunfriendlyÆ chemicals for dense media separations that have considerable impact on handling and disposal. Wet processing also increases operating costs due to plant instability, materials handling, thickening, filtration and product drying. The new CSIRO technology exploits a combination of natural and applied forces to achieve specific particle motions that produce size separation. In doing so, many of the traditional shortcomings of dry separation have been overcome. The CSIRO Dry Particle Size Separator is ideally suited for dry size separation applications within the size range 1 mm to 30 ¦mfor moderate moisture levels (2 per cent), have low unit throughput, produce a fixed cut size and are therefore impractical where very high unit capacity and low operating costs are required. This paper presents a review of dry separation devices together with details of the new Dry Particle Size Separator and typical results for a number of materials, including iron ore and quarry dust.

Jan 1, 2002

Discussion of the paper of C. M. YOUNG, presented at the St. Louis meeting, October, 1917, and printed in Bulletin No. 129, September, 1917, pp. 1369 to 1384. CARL SCHOLZ, Chicago, Ill.-Mr. Young was kind enough to&apos; allude to the development of a mine in which I am now engaged. Several months ago the Burlington Railroad decided to open a mine in the field Which they own in Franklin County containing some 15,000 acres .(6070 ha.) of coal, ranging in thickness from 8 to 12 ft. (2 to 3.6 m.). This proposition in itself is attractive to any mining engineer, but with the backing of a large company I saw an opportunity to do some novel work in the construction line, and for several months I have been investigating and working on the problem of developing what I hope will be the largest and best equipped mine in the State of Illinois. The shaft will be sunk at a place where the coal lies at a depth of 600 ft. (182 m.) and conditions both of the surface and of the coal are ideal in every way; the seam is almost level, and we had only 7 ft. (2 m.) of surface clay to go through. We are going to hoist by skips in order to reduce the rope speed. I believe that is a long step in the direction of economy, because we not only double the output of the mine by hoisting the contents of two cars atone time, but we reduce the proportion of dead weight. In our case there will be 20 tons of coal and 18,000 lb. of skip, or 55 per cent. net and 45 per cent. tare. That, of course, necessitates less than half the rope speed for the same tonnage, and we all know that speed means power and power means cost. Skip hoisting permits the use of solid-end gate cars, which is an advantage. The cost of these cars will be in the neighborhood of $250 apiece; They are well built, with roller-bearing wheels of the most up-to-date type, spring draw-bars, and refinements of-that character which are necessary to move the loads most advantageously.

Jan 1, 1918

By J. Shibata, N. Murayama

"Rare earth elements are present in more than 100 minerals, of which monazite, bastnaesite and xenotime are typical. Rare earth elements have excellent chemical and physical properties for industrial use in functional materials such as phosphors, magnets, electronic components, abrasives and catalysts. China produces more than 90 % of the world’s rare earths, and Chinese trends significantly influence the demand and price of rare earths. From the viewpoint of resource securement, it is desirable to separate and recover rare earth elements from low-grade resources and wastes. Phosphate gypsum, which is a by-product of wet phosphoric acid manufacturing, contains low concentrations of rare earth elements. In this research, the separation and recovery of rare earth elements from phosphate gypsum were investigated. A series of recovery methods including washing of phosphate gypsum, leaching of the rare earth elements with sulfuric acid, adsorption and desorption of rare earth elements by using ion-exchange resin, and precipitation of rare earth oxalates were carried out. The separation of rare earth elements from Ca2+ simultaneously leached from phosphate gypsum was also investigated."

Jan 1, 2014

Magnetite cenospheres 40-270 I/m in diameter have been found during the combustion of pyrite concentrate.Micrographs of the surface and internal structures are presented together with comment on the mechanism of forrnation.The similarity to cenospheres found during the combustion of pulverized fuel was noted and speculation raised to their contribution to the dust and fume load in flash smelters.

Jan 1, 1980