Search Documents

By S. Gupta, M. Fuka

This paper reports for the first time the synthesis of deintercalated MoAlB particulates which belongs to a family of novel ternary borides called MAB phases by selected etching of Al from these particulates by treating them with a solution of LiF and HCl. The FESEM analysis showed that these particulates hada stacked 2D-particles like morphology reminiscent of multilayered MXenes, but unlike MXenes, the 2D layers were interconnected with anisotropic porosity between them with an average length and width of pores being 257 ± 126 nm and 35 ± 10 nm, respectively. The EDS analysis of particulates showed that a typical particulate had a chemistry of (Mo Al )B{O F } which indicate partial 0.67 0.33 0.19 0.02 deintercalation of Al from the particulates. These novel particulates were also referred to as MABenes due to their microstructural similarity with multilayered MXenes.

Mar 1, 2018

By M. H. Rinkenbach, C. A. Taylor

The detonating compound cyanuric triazide was discovered*** and patented**** by Erwin Ott, and on account of his claims, the Bureau of Ordnance, U. S. Navy, desired more complete data, so an investigation was made. The results obtained were such that the Bureau of Crdnance recommended publication thereof for the benefit of the explosives industry. Some of the patent claims regarding cyanuric triazide are as follows: 1. It is not poisonous in contradistinction to fulminating mercury and lead azide. 2. In contradistinction to the hitherto employed priming agents it is fusible, and its fusion point (94°C) is so low that the product melted by a single heating in water or steam bath, can be poured without danger in the capsule shell. It solidifies therein after cooling, and shows the density of 1.5. 3. It has been determined that the cyanuric triazide, in spite of its very much higher priming actions, is much less brisent then ful- minating mercury and lead nitride. 4. The chemically pure cyanuric triazide (C3M2) constitutes colorless crystals melting at 94°0., and is not volatile. It is not affected by cold water, and only slowly saponified by hot water. It is relatively insensitive to friction and not too strong concussion, but explodes by impact or when hea ted to 170°C., or when heated suddenly. It is not more sensitive to friction and shocks then fulminating mercury. 5. The preparation of the triazide is preferably carried out by acting with an excess of sodium azide in an aqueous solution; in the cold, on cyamric chloride gradually suspended in the said solution.

Aug 1, 1923

By M I. Pownceby, N A. S Webster, R Pattel, N Ware

The decrease in quality of Australian iron ore, coupled with the demand for more efficient energy use, necessitates closer monitoring and optimisation of process conditions for iron ore sinter production. Sinter properties are correlated with the mineralogical content and traditionally, quality control has relied on methods such as Fe2+ determination, point counting via optical microscopy and automated electron beam techniques such as QEMSCAN; these can have a typical turnaround time of several days between sampling and reporting of results. As well, there is additional uncertainty around quantifying some of the complex mineralogical phases in sinter such as silico-ferrite of calcium and aluminium (SFCA) and SFCA-I, which are key phases influencing sinter quality. There is a clear need for the implementation of alternative analytical methodologies that offer a turnaround in hours or even minutes to provide information to accurately maintain production conditions.X-ray diffraction (XRD) is a technique widely used for the quantitative mineralogical phase analysis (QPA) of ores and processed materials in the iron ore industry. Partial least squares regression (PLSR) analysis methods have recently been suggested as an indicator of sinter Fe2+ content from powder XRD data without the need for rigorous and often time-consuming mineralogical analysis by the operator. In this study we provide results from the implementation of PLSR to predict the strength of iron ore sinter. Results are sourced from a well-constrained data set comprising strength properties (as quantified by a tumble index (TI)) from a series of compact laboratory test samples. Using this data set it was determined that PLSR has potential to be used as a method for calculation of sinter TI from powder XRD data and, therefore, process control.CITATION:Webster, N A S, Pownceby, M I, Ware, N and Pattel, R, 2017. Predicting iron ore sinter strength through X-ray diffraction analysis, in Proceedings Iron Ore 2017, pp 331–334 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Thomas G. Langton

The demand for mineral raw materials, especially in the major industrialized nations, has grown rapidly during the past three decades. One consequence of this growth has been an increasing reliance by the large industrialized countries upon nondomestic mineral supplies. These mineral supplies, to a large extent, have been developed by capital from the major industrialized countries. Until recently, most foreign mining ventures were either wholly-owned subsidiaries or joint ventures between two or more mining companies. The recent rise of economic nationalism has substantially changed the business climate and parameters under which foreign investors operate. This paper describes some of the underlying reasons for this change and notes how investors have adapted to the new business conditions.

Jan 1, 1974

By John Lund

INTRODUCTION GOLD-BEARING placers of Alaska and the Yukon Territories are buried under a layer of permanently frozen alluvial overburden, or 'muck', which varies in depth from twenty to one hundred feet. The placers, and the decomposed bedrock layers upon which they are deposited, are also permanently frozen. During the summer, surface muck which is exposed to the sun will thaw, but only to a depth of a few feet. To reach a valuable deposit, the frozen overburden must be either penetrated with shafts, or stripped from the deposit entirely. In either case, before the placer can be mined, it must be thawed. At modern dredging operations, the frozen muck is stripped from the placer by powerful jets of water from hydraulic giants. The placer, and several feet of decomposed bed-rock, are then thawed by forcing water through narrow pipes which have been driven into the deposit. Other methods of thawing frozen placers were used extensively during the early years of the Klondike 'gold rush', but experimentation later proved that creek water at its natural summer temperature was a more effective and economical thawing medium than any other which had been used. EVOLUTION OF COLD WATER THAWING Early prospectors of the far north reached placers by digging shafts through the frozen muck. They then thawed the placer sand and gravel by building wood fires at the bottom of the shafts.

Jan 1, 1951

By Michael J. Virnig, Keith E. Weerts

The development of heap leach technology for the treatment of low grade gold and silver ores has led to a boom in gold production in the Western United States in the last 15 years. The heap leaching process consists of stacking the mined ore on a specially prepared leach pad followed by leaching with dilute alkaline cyanide solution. Depending on the nature of the ore, it may require crushing and/or agglomeration prior to stacking on the leach pad. As the dilute alkaline cyanide solution migrates down through the stacked ore, the precious metal values along with a portion of the base metal values present in the ore are dissolved to give a pregnant leach solution which is collected at the base of the stacked ore. The precious metal values are then recovered by zinc precipitation or by adsorption on activated carbon. Once all of the economic metal values have been leached from the ore, the spent heap leach pad, the leached materials, and associated process solutions must be decomissioned. Decommissioning requires that the spent heap leach pad along with the leached materials and process solution be treated to reduce the concentration of the residual cyanide, base metal cyanide complexes, and other anionic metal species to levels where they no longer represent a long tenn liability for the environment and the operator. The levels to which these components must be reduced is dependent upon the applicable water quality standards as determined by the responsible federal, state, and local agencies. As environmental awareness has grown, these standards have become increasingly stringent. A number of treatment options have been developed for the de-toxification of the process residues. These include natural degradation which incorporates bio-degradation, fresh water rinsing, alkaline chlorination, hydrogen peroxide, and sulfur dioxide/air. Each of these options has been reviewed with regard to relative effectiveness, generation of hazardous by­products, reagent handling considerations, relative costs, and time requirements by Denton, Iverson, and Gosling I. As an outgrowth of the program to develop Henkel's guanidine based gold extractants, COGNIS, Inc., the environmental ann of Henkel, has developed the CyanoMet R process for the extraction and concentration of the various cyanide and anionic metal species from the dilute aqueous alkaline solutions generated during the process of detoxifying spent heap leach pads. This paper describes the CyanoMet R process, its application to three different feed solutions, and treatment of the concentrate generated by the process.

Jan 1, 1993

By C. E. McElroy

"INTRODUCTION The ventilation of working places in mines by jets of air discharged from fan-pipe lines is an important phase of mine ventilation, whether the primary purpose is to dilute gas or dust concentrations or to provide air-motion cooling effect. Jets of similar nature are very prominent factors in the ventilation of enclosed spaces, such as buildings and ships. The effectiveness of such jets depends on the distribution of the air in the jet streams, a subject on which the little definite information previously available applied to jet discharge into large, open spaces under conditions quite different from those ordinarily associated with fan-pipe discharge in mines.The results of an initial series of experiments on the discharge of air from fan-pipe lines in mine openings have been described. 3/ This report presents the results of a second series of experiments and compares the results of both series with theory and experiment on jet discharge into large, open spaces. The results of this second series confirm and supplement those of the initial series, in which a 10-inch pipe discharged into an 8- by 8-foot develop¬ment end through seven short discharge pieces of different designs. In the present series the same 10-inch line was used, but the discharge was through 10- to 30-foot lengths of 5-inch, 10-inch, and 20-inch-diameter pipes and through a 20-foot length of 29- by 3-inch pipe. Tests were made with the air discharged into a closed drift or development end, as in the previous series (in which case the discharged air returned past the end of the pipe) and into an open drift (in which case the discharged air did not return past the end of the pipe but continued out along the drift). Test conditions corresponded to the discharge of a jet into a channel closed at one end; in one case, the discharge was directed toward the closed end and in the other toward the open end. The former typifies fan-pipe ventilation of development ends and the latter an abrupt increase in the sectional area of an airway. In both the flow had to pass from jet to open air against some resistance.The tests were made in the Mount Weather Testing Adit of the Bureau at Bluemont, Va., on the pipe line installed for ventilating the adit, and extended from late September to mid-November 1940. Preparations were made for directly comparable series of experiments on the injector effect of fan-pipe discharge in an open drift and on free expansion in large, open spaces, but these test programs were .first postponed in favor of other work and finally abandoned until the war is over."

Nov 1, 1943

By Steve Kral

Conference themes are usually chosen by organizers to reflect the current state of the industry. The Colorado Section MPD came up with what may be the most appropriate theme of a mining conference during the last few years. The local SME MPD section’s theme of its 56th annual conference was “The Wild, Wild World of Mining.” The current boom can be felt in all aspects of the industry, including exploration, mining, processing, sustainability, and economic and political issues. Each of the 25 speakers at the conference, held in Colorado Springs, CO, touched on how the boom has impacted each of those aspects. The meeting attracted about 110 people from around the world.

Jan 1, 2006

By X. B. Starnes

"INTRODUCTION The Eva Tanguay property is in Crittenden County, Kentucky, about 1 mile south or the village of Mexico, and can be reached from Marion, the County seat, by travellng south on State Highway 91 for 6.8 miles and then turning southwest on State Highway 70 and traveling 2 miles farther.Although the property lies between the Huffaw and Pigmy properties, which together have produced 200,000 tons of fluorspar ore, production from the Eva Tanguay has been estimed at only 1,000 tons. Geological factors on the property indicated the likelihood of an ore occurrence, and the author examined the property in April 1944. Shortly thereafter, the U.S. Geological Survey wrote a report on the property, which was not published. A drilling program was initiated by the Bureau of Mines November 1, 1944, and continued until eight holes totaling 3,137.5 feet were drilled.The holes showed that the Tubb fault system on the Eva Tanguay property is composed of three members, all of which contained commercial ore. The line dividing the Haffaw and Tanguay properties crosses the vein outcrops, causing a part of the ore indicated to be on each property.The mineral rights, which are leased by Robert Frazer of Marion, are owned by Mrs. O. S. Denny and W. C. Bohn, both of Marion."

May 1, 1947

By Brian O'Hearn, Doug Hanson

"The most commonly used tendon supports in the Sudbury area include rock bolts, rebars, friction anchors and cable bolts. Due to the fact that these tendons are physically different and employ different anchoring systems they offer varying degrees of stiffness, yield ability, load capacity, anchor dependability and energy absorption. These differences coupled with variable rock mass and changing stress conditions have made it challenging to engineer the design of an effective support system. By tapping into the knowledge and experience gained by ground control practitioners, an empirically based rating system has been assembled that offers a guide to designers of support systems when choosing the most effective tendon support over a range of rock mass and stress conditions.A methodology referred to as support planning can be used to design support systems whose rehabilitation costs will be minimized. The use of multiple tendon types in anyone support layout is advocated, particularly when the stress state of the rock mass to be supported is expected to undergo a change."

Jan 1, 1995

By Ketteridge IB, Mulcahy DE, Quast KB

The long term energy demands in South Australia are such that there is a distinct possibility that one of the lignite deposits in the State will be exploited to feed a pulver- ised-fuel power station. Bowmans lignite deposit is the largest lignite deposit in South Australia and is considered to be a contender. The deposit is ideally situated (100 km north of Adelaide) but the quality of the lignite is poor (see Table 1). TABLE 1

Jan 1, 1984

By Eduardo de Oliveira Diniz

“Excelência no atendimento aos clientes” é uma máxima declarada como busca constante em todos os segmentos de mercado, inclusive no de aços longos, negócio da ArcelorMittal Monlevade. Com foco neste objetivo, muitas vezes, a empresa se volta para o mercado na tentativa de mapear as necessidades dos clientes. Após identificá-las, e absorvê-las, acaba-se criando complexidades em processos tanto em produtos quanto em serviços. A cada internalização de demanda, segue-se a rotina sob a ameaça de transformar o processo de atendimento em algo confuso e desatualizado, além de não haver segurança de que o cliente está satisfeito de fato. Este trabalho mostra o histórico recente de uma expressiva evolução do atendimento aos clientes da unidade de Monlevade, resultado obtido através de análises, utilizando a metodologia PDCA, que orientaram a uma nova estrutura da equipe de atendimento na Gerência de Logística, implicando em reformulação de acompanhamentos/controles de processos e intensificação dos contatos com pessoas envolvidas com atendimento aos clientes dentro e fora da planta. Com isso, foi possível superar, de forma consonante, a proposta da Logística Central de implantação de uma “Célula de Atendimento” em cada unidade da ArcelorMittal. Conclui-se que é necessário rever periodicamente a rotina de processos internos de modo a buscar um equilíbrio entre as necessidades dos clientes, complexidades geradas e resultado dos índices de atendimento.

Aug 16, 2017

By Edgar J. Briceño

El presente texto señala el resultado de algunas pruebas realizadas en el período de 1974 y 1979 en la concentradora de Toquepala, a fin de mejorar el proceso de producción en la industria minera. Para ello, se ejecutaron 14 pruebas a nivel de planta, de donde se seleccionaron seis, las cuales se ejecutaron también a nivel de laboratorio para así compararlas con lo standard. Las seis pruebas referidas son: Evaluación de forros de jebe en molienda, evaluación de diferentes tamaños de bolas, evaluación del espumante Celaproht-16, efectos de Asmol Polhalla m- 59 en sedimentación y filtrado de las colas de planta de Molibdenita, evaluación del espumante Ucon R-23 y lonas tampereen en el filtrado,

Oct 14, 1980

By Paul Hatmaker

Lime was a highly useful commodity thousands of years before the simple chemistry of its manufacturing process was known. The employment of lime for agriculture, building, and even certain essentially chemical purposes is so old that its origin is among the unrecorded details of man's first ventures into the manufacture and use of prepared substances. Lime is a most versatile material and consequently has come to be widely utilized in modern civilization. Immediately before the depression of the early 1930's the annual production of lime in the United States was more than 4 million tons, valued at 33 to 42 million dollars. This output was sold to many industries, so many that mere enumeration becomes tedious. In addition to agricultural and building lime the sales statistics compiled annually by the Bureau of Mines include lime sold to the steel and other metallurgical industries as refractory and fluxing material, as well as that used by paper mills, glass works, tanneries, and water-treatment plants. These major uses normally consume about 86 percent of the domestic sales. The remaining 14 percent includes lime sold for use in the manufacture of alcohol, alkalies, bleaches, calcium acetate, calcium carbide, coke gas and byproducts, glue, insecticides, oils and fats, paints, and rubber, in the refining of salt, in the manufacture of sand-lime and slag brick, in the disposal of sewage and garbage, in the manufacture of silica brick, in the refining of sugar, in the textile industries, and in wood distillation. Many other uses are also known for which complete sales data are not available.

Jan 1, 1934

By AIME AIME

A CERTAIN area in the State of Indiana seems to be a breeding place for presidents and near president about eighteen miles southeast of Elwood is the little village of Daleville, and there, on April 9, 1890, John Robert Suman, newly elected President of the A.I.M.E., was born. It was not long before he migrated to California, however, where he went to the Los Angeles High School, then for two years to the University of Southern California, after which he went up to Berkeley

Jan 1, 1940

By Oliver C. Ralston, Foster Fraas

"INTRODUCTION The predominant characteristic of powdered mica is the thin -plate shape of the particulars, and the thinner the plates, the more enhanced is this characteristic. Consequently, it is frequently desirable to grade mica according to the thickness of the plates. Concerning the various possible methods for grading mica, very little has been published. There is also no information on the relative quantities of mica per given range of plate thickness. This paper presents a graphical method that shows how these quantities are distributed and how the different methods of grading compare.CUMULATIVE BULK DENSITYBulk density, which is an indirect measure of the plate thickness, was determined in a small cylindrical cup of 3.37 cubic centimeters volume. The mica was placed in the cup under a standard procedure. The densities thus measured checked these determined in a 273 cubic centi¬meter cup with less than a 2 percent error.In calculating cumulative densities it is important to know how they are averaged. In any grading operation the bulk density of a series of fractions is determined. Starting with the lowest density fraction, the cumulative percent under-density can be calculated through the various fractions. It is possible that quantity may be measured by volume or weight and that the averaging may be done by a number of methods. However, experimentally it has been shown that the quantity must be by volume and that the averaging must be arithmetic. This is illustrated in table 1, in which the calculated and actual bulk densities are listed."

Sep 1, 1942

By C D. Rawlings

An assessment is made of the potential for thick seam underground mining of black coal in Australia. A brief summary is given of the geo-mechanical environment and previous mining history existing in a number of areas of particular interest from the point of view of thick seam mining. A classification of thick seam mining methods is presented with emphasis on the critical geo-mechanical parameters influencing the performance of such methods. A summary is made of perceived geo-mechanical research requirements related to thick seam mining in Australian coalfields.

Jan 1, 1980

By S. Nikolic, O. O. Kehinde-Philllps, O. T. Djamgouz, D. H. Rousell

"A bulk mining method is employed at the Lockerby mine resulting in the formation of large muck-piles. If these muckpiles remain in the stopes for some time they may agglomerate to the extent that the muck cannot be removed by a scooptram. A laboratory investigation was undertaken with sulphide material from the mine in order to detemine the time that oxidation begins and the flowability of the material as a f unction of several factors. The laboratory results are applied to the conditions in the muck-piles.The time of the beginning of oxidation of the material decreases as the sulphide composition, water content and availability of air increases. Oxidation is retarded by the addition of a copper sulphate solution instead of water. The unconfined yield force (strength} of the material increases with an increase in the sulphide composition, water content and time. The material ceases to be free-flowing before there is visible evidence of oxidation and this suggests that oxidation actually begins earlier and that agglomeration is also due to the capillary action of water.Broken ore should be removed from the stope prior to the time a muck-pile ceases to be free -flowing-perhaps as early as two days f or high-grade ore and 5 days f or low-grade ore. In order to control dust, 1.4 weight per cent of a 5 per cent solution of copper sulphate should be added 10 the muck-pile rather than water. This inhibits oxidation and increases the time that a muck-pile remains free-flowing."

Jan 1, 1984

By Patrick Oriez, Chris Norris, Alain Mercusot

"Temporary mechanical ventilation is one of the fundamental requirements in guaranteeing a healthy atmosphere in underground construction works in order to protect the health of persons working on the site. It is therefore essential to conceive a system which meets the requirements of the whole of the worksite and for all phases of work which takes into account all aspects pertaining to its design, dimensioning, justification, installation, maintenance and validation. In doing so, the ventilation design and the selected apparatus to be installed shall meet with the degree of health protection and the quality of air of the worksite as defined by the legislation in force in France, through limiting the concentration of the different pollutants associated with the site activities. Consequently, when presenting a mechanical ventilation project, all of the participating parties and especially the contractor make a commitment to guarantee sufficient volumes (or airflow rates) of fresh (non-polluted and oxygenated) air and extracted (polluted) air in order to meet these limitations and maintain them in all conceivable site configurations. This article sets out the most important aspects of the implementation of a ventilation project from the initial design stage through to its application, discussing French legislation, ventilation principles, calculations and techniques with regards to underground construction sites. BASICS OF VENTILATION Mechanical ventilation studies are concerned with all of the site workstations and work phases which are sources of pollution and apply to all zones of the underground worksite with the goal of maintaining the concentration or composition of this pollution below the permitted levels and comply with the following three basic principles which are complementary to one another without being in contradiction. •,The first principle consists in eliminating or limiting as much as possible the emission of any polluting, irritant, or dangerous substances, by specifying appropriate construction techniques and equipment (use of electric motors, combustion engine equipment: filters, tanks, catalyzers, use of less polluting explosives, damping down dust with water or wetting products, damping down and diluting certain gases using water mists). •,The second principle is designed to capture residual polluting substances emitted close to the source in order to prevent them from spreading into the worksite atmosphere (extraction ventilation with ducting up to the source – upstream of the extractor fan – and use of downstream filters before expelling the polluted air to the exterior). •,The third principle involves accompanying the capture of the pollutants with additional blowing ventilation specific treatment of substances dissipated by and distant from the source of pollution (acceleration of the drift air flow in order to confine dust and better capture it, supply ventilation with ducting in order to dilute the gases emitted and discharge them to the exterior)."

Jan 1, 2016

By Mark Rebagliati, John Payne, Jim Oliver

Abstract-The Campo Morado precious-metal-bearing, volcanogenic massive sulfide deposits occur in a lower Cretaceous, bimodal, calc-alkaline volcanic sequence in a major northerly trending belt in the Guerrero Terrane in northeastern Guerrero, Mexico. During upper Cretaceous to Early Tertiary greenschist-facies regional metamorphism, the rocks were deformed strongly into a northeast-verging fold-and-thrust belt. Three later stages of weak deformation were dominated, respectively, by kink folds, broad warps, and extensional faults. Most deposits occur in the upper part of a sequence of felsic flows and heterolithic volcanoclastic rocks or at its contact with overlying chert and argillite-sandstone. The Reforma and El Rey massive sulfide deposits are on the overturned limb of a major, thrusted anticline, and the Naranjo and El Largo massive sulfide deposits are to the south on the upright limb of the same major fold. The La Lucha and San Rafael massive sulfide occurrences are in an upper plate to the southwest which was thrusted over the plate containing the Naranjo and El Largo deposits. In several of the deposits, Au, Ag, Zn, and Pb are concentrated near the stratigraphic top, and Cu is concentrated near the stratigraphic base. Major minerals are pyrite, quartz, ankerite, sphalerite, chalcopyrite, and galena. Minor minerals are tennantite-freibergite, arsenopyrite, and pyrrhotite. Gold and Ag occur in argentian gold, and Ag also occurs in tennantite-freibergite. The cumulative inferred resource of massive sulfide for the Reforma, Naranjo, El Rey, and El Largo deposits exceeds 30 Mt, with the latter two deposits incompletely delineated. Underlying pyrite-quartz stockwork zones contain chalcopyrite, chlorite, and sphalerite. Hydrothermal alteration minerals in the stratigraphic footwall are pyrite, quartz, chlorite, ferroan dolomite, and ankerite. In the stratigraphic hangingwall, hydrothermal alteration minerals are sericite, calcite-dolomite, and lesser clay minerals and quartz. The deposits belong to a low-sulfidation, volcanogenic massive sulfide system formed in a subaqueous environment, and are of the bimodal, siliciclastic type.

Jan 1, 1997