Search Documents

By W. H. Oppelt

Two exploratory gasification tests of limited duration were made at Dorsten, Germany, with strongly coking Pittsburgh-bed coal in a fixed-bed pressure gasifier. To reduce the coking potential of the Arkwright coal, ash refuse from the gasification of Dorsten (Leopold) coal was added to pre-pare coal-ash mixtures which contained nominal 20 and 30 percent ash. Major adjustments in principal process variables at the beginning of the tests resulted in wide fluctuations in the rate of gas production, gas offtake temperature, and carbon dioxide concentration in the gas. Because a higher steam-to-oxygen ratio was used in the tests than was customarily employed for routine operation, gas production was lower, and steam and oxygen consumption was higher. After operating conditions had been improved, the results of a 12~-hour-long test with addition of sufficient ash refuse to obtain a nominal 30 percent ash concentration indicated that operation is feasible with this coal mixture using a fixed-bed pressure gasifier equipped with a rotating coal distributor and stirrer.

Jan 1, 1966

By A. U. Seybol

Eight binary iron alloys were examined after ion nitriding experiments to determine the behavior of the following elements: Al, Mo, Mn, Si, Ti, V,Cr, and C. Only Al, Cr, Ti, and V additions caused hardening in binary iron alloys. A few steels were examined to see the effect of Cr, Cr + Al, Cr + Ti, and Cr + V. It is suggested that a useful new class of ni-triding grade steels might be those containing about I pct V. The nitriding of steel, first described by Fry1 about 45 years ago, rapidly attained commercial application with very little knowledge of the fundamentals involved. While Fry,' in describing the status of nitriding in 1932, apparently correctly postulated hardening by precipitated nitrides, the details of the nitriding process were not understood, nor has the situation changed much since that time. It is also interesting to note that the compositions of some typical nitriding steels given by Fry at that time have changed little in the intervening years. Currently used nitriding steels owe their surface hardening to either chromium (as in 4340 steel) or aluminum plus chromium as in the Nitralloy grades, where both CrN and AlN appear to contribute to harden ing. Titanium additions have been studied experimentally, but thus far titanium steels have not won wide commercial acceptance. This subject will be expanded later. The orthodox ammonia nitriding process has been reviewed very adequately many times as in Jenkins3 and Case and VanHorn,4 and their is no need to outline the process here. Ion nitriding is not as well-known, although there have been several descriptions5-9 of the process given, sometimes with comparisons with the ammonia process. Most of these papers are primarily concerned with a description of the equipment, or of the physics or electrical engineering aspects of ion nitriding, but Noren and Kindbom9 gave the results of a metallurgical investigation using both processes. In brief, ion nitriding is carried out in a vacuum chamber from which the air is exhausted and replaced by a N2-H2 mixture, typically containing 10 to 20 pct N2, at about 5 to 10 torr pressure. While ammonia gas has also been used in ion nitriding, there is no evidence that ammonia makes any improvement in the ion nitriding process. A few hundred volts dc is applied between the grounded container wall (positive) and an insulated center post supporting the work (negative) to be nitrided. A glow discharge is created in the ionized gas, accelerating positive nitrogen ions to the work. These ions contain enough energy to form the normally unstable Fe4N "white layer", thus establish- ing surface nitrogen solubility characteristic of the a Fe/Fe4N equilibrium. This creates a substantial concentration gradient, driving dissolved nitrogen into the steel. The temperature employed is in the same range (around 500" to 550°C) as in ammonia nitriding, but because of factors which are not understood at present the nitriding time is ordinarily considerably reduced in ion nitriding. Other advantages have been cited,9 but it is not the purpose of the present work to contrast the two processes. The present objective was to examine the behavior of binary iron alloys during ion nitriding with respect to the microstructure, hardness level, and depth, and to examine some of these factors in steels as well. In this way it was hoped to be able to find out something about the individual role of these elements in steels. While all the work was done by ion nitriding, there seems to be no reason why any conclusions reached would not equally apply to ammonia nitriding, excepting only the kinetic aspects of the process. Another objective was an exploration of the critical-ity of the ion nitriding variables: gas composition, pressure, temperature, and time. EQUIPMENT AND MATERIALS The equipment used was substantially as described by Jones and Martin.8 The vacuum tank was about 12 in. in diam by about 18 in. high, and consisted of water-cooled stainless steel, with a single small window at the top for viewing inside. This sat on a heavy mild steel base equipped with the main pumping port, pressure control port, and vacuum gaging. A series of variable resistances was interposed between the glow discharge and a large-capacity -40 amp variable primary transformer feeding a 1000-v transformer, but 600 v were about the maximum ordinarily used. With the small l-in.-round, 4-in.-thick discs used for nitriding, the electrical load was usually about 500 v at 0.8 amp. The specimen temperature was controlled by a stainless-steel sheathed chromel-alumel couple, whose junction was in the steel stool upon which the flat discs were placed. These were ground through 400 Sic paper. Cycling of the temperature controller caused -0.2 amp variation in ion current, providing an ample control band. The binary iron alloys were made from vacuum-melted hydrogen-deoxidized electrolytic iron and alloys of 99.9 pct purity. Cast ll-lb-square tapered ingots were forged and hot-rolled to about 11/4-in.-diam rounds. Discs of 1/4 in. thickness by about 1 in. diam were machined from the rods for nitriding specimens. The following alloys were prepared: 1 pct each of Mn, Mo, Cr, Ti, Al, V, Si, and an Fe-0.8 pct C alloy. EXPERIMENTAL VARIABLES Of the variables total gas pressure, nitrogen partial pressure, temperature, and time, only nitrogen partial pressure was found to be critical to the operation. A critical nitrogen partial pressure was found corre-

Jan 1, 1970

By W Valery, S Morrell

In the mining industry blasts are usually designed to fracture the in situ rock mass and prepare it for excavation and subsequent transport. The run of mine (ROM) fragmentation is considered good when it is fine enough and loose enough to ensure efficient digging and loading operations. Mining optimisation strategy is hence usually focussed on minimising total mining costs and maintaining these ROM fragmentation characteristics. Although this approach ensures an efficient mining operation it ignores the potential impact on crushing and grinding. Investigations by several researchers have shown that designing blasts to produce ROM fragmentation to optimise crushing and grinding performance enhances the overall efficiency and profitability (Eloranta, 1995; Kojovic et al, 1995; Bulow et al, 1998; Kanchibotla et al, 1998; Scott et al, 1998; Simkus and Dance, 1998). Field experimentation in this area is often found to be difficult because of high implementation costs and insufficient understanding about the effect of fragmentation at different stages in a comminution circuit. Modelling and simulation of blasting and comminution processes provide a more economic alternative to explore the impact of blast design changes on the down stream operations (Kanchibotla et al, 1998; Kojovic et al, 1998; Adam and Siddall, 1998; Bulow et al, 1998). However, the reliability of such simulations depends on:the ability of the models to reproduce the physical processes that take place; characterisation of rock mass in terms of its blastability and comminution characteristics; and in the case of blast modelling the ability to predict fines (-10 mm) has been found to be particularly important as this fraction has a significant effect on mill throughput.

Jan 1, 1999

By Osamu Taki

This paper presents the system, the strength of column, the design concept, and the applications with four case histories from the past project as the general aspect of Geo-Column (trade mark of single soil-cement column by SCC Technology, Inc.). In the system, it shows the installation process and drilling/mixing tool with the mixing process. In the design concept, it shows how to design Geo-Column against the vertical and horizontal load. Finally, it shows the applications with four case histories, (1) building mat foundation, (2) isolated foundation on the pedestrian bridge, (3) bridge spread footing and slope erosion control wall in the channel, and (4) cut-off wall and shoring wall in the underpass roadway to the railroad.

Jan 1, 2000

By Willis Carrier

PARTICULAR interest in the ventilation of deep mines, especially those in South Africa, has been created by a very complete system of cooling of the world's deepest mine, the Turf shaft of the Robinson Deep ill Johan-nesburg. The writer visited this mine in January, 1936, and again in 1937. During these visits and subsequently, a considerable part of the theory involved in rock cooling in tunnels was developed and this has been checked by practical observations of the rates of rock cooling made within mines. The purpose of this paper is to set forth the method of attack of the mine problem. The cooling or air conditioning of mines by the use of mechanical refrigeration was not wholly new 1-5 when the Robinson Deep installation was made. The first mine to be cooled was the Morro Velho mine, in Brazil. The first installation in this mine was put into operation in December 1920, the refrigerant being ammonia.5 The surface cooling gave considerable benefit but it proved inadequate as greater depths were reached, therefore in 1929 two centrifugal refrigerating machines were installed at the 6000-ft. level. These were used in conjunction with the surface cooling system to furnish additional cooling at the lower levels. This later installation used Carrene as a refrigerant. This nonflammable refrigerant, having a boiling point of 104° at sea level, insured reasonable safety, since all parts of the machine operated At subatmospheric pressure. Very favorable reports have been received on the effectiveness of this installation, but no recent data are available. An interesting feature of that plant is that the condenser water is cooled by spraying it into the exhaust air from the mine at the base of the ventilation upcast, which permits the water to be cooled within a few degrees of the wet-bulb temperature of the air entering the upcast, and the only water that has to be supplied for condensing purposes is that lost by evaporation, or about 0.5 per cent of the volume circulating through the condenser. This plan affords an ideal means for the removal of the heat load from the refrigerating system, and of course also from the mine itself. In many mines, however, especially those in South Africa, there is no

Jan 1, 1938

By M. J. Makhula, R. M. S. Falcon, S. O. Bada, L. M. Falcon

"SynopsisThe combustion and co-combustion behaviour of macadamia nut shell, high-ash coal, and anthracite, along with their blends was studied using thermogravimetry. The reactivities of all samples were analysed in air, oxygen, and CO2 atmospheres and at different heating rates from 10 to 40°C/min. Macadamia shell was found to have a lower ash content, 0.36%, than coal with 27.49% ash. The calorific values were similar, 19.64 MJ/kg and 19.44 MJ/kg respectively. The differential thermogravimetric results indicate that as the heating rates increase the ignition, peak, and burnout temperatures increase significantly, leading to high combustion rates. The interaction between the fuels was evaluated using the weighted average model, and the results indicated that there is more synergetic interaction between 20% macadamia plus 80% coal under oxygen than in air and CO2 atmospheres. The results of the investigation provide the combustion and co-combustion characteristics of various samples and their blends and indicate their combustion compatibilities. IntroductionThe global macadamia nut industry is developing at a very rapid rate. South Africa is currently the world’s third largest producer, with a production of about 35 000 t as of 2012 (Department of Agriculture, Forestry and Fisheries, 2013), compared to 840 t produced in 1996. The greatest numbers of the macadamia nut farms in South Africa can be found in Mpumalanga, Limpopo, and KwaZulu-Natal provinces, with Mpumalanga as the largest producing area. There are many factors influencing the increased demand for macadamia nuts, the most important factor perhaps being their nutritional value (California Dried Fruit and Nuts, 2011; MPC, 2014) and their suitability as a feedstock for manufacturing cosmetics, bakery products, nut paste, chocolates, sauces, and ice-cream. As a fuel, macadamia shell has a high heating value ‘as-fired’ of about 20.71 MJ/kg (Vhathvarothai et al., 2013), which could in turn be used in drying the nust, and the shell could also be milled and applied as a fertilizer."

Jan 1, 2015

By Italo Onederra, Jason Furtney, Ewan Sellers

The detonation reactions occurring during rock blasting result in high pressure gas phase products from the condensed explosives typically used in mining applications. After detonation and the initial fracturing, the work done by the expansion of this gas contributes to burden movement and further rock fracturing. Before all of the energy in the reaction product can do useful work on the rock, some of this energy is lost to crushing and possibly to gas venting to the atmosphere. Borehole gas pressure decreases by three principle mechanisms: (i) expansion of the borehole cavity, (ii) flow into the fracture network, and (iii) flow through the stemming. To simplify the problem and to get a better understanding of the interaction of these mechanisms, a simple model for each of these mechanisms is developed. A comparison is made of the time-scales and the influence on burden movement for each. A comparison of gas flow behavior is made between typical ANFO and emulsion products.

Jan 1, 2012

By R C. Schodde

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Over the last decade (2005–2014), a total of 439 significant deposits of gold and base metals were found in the world. Twenty (or 4.6 per cent) of these deposits were in the Pacific/South-East Asia (Pacific/SE Asia) region. In terms of contained metal, the region accounted for 1.6 per cent of gold and 13.8 per cent of copper found in the world. With regard to nickel and zinc/lead, the region’s contributions were insignificant.Over the same period, the Pacific/SE Asia region accounted for 6.6 per cent and 12.6 per cent of all gold and copper exploration expenditures in the world respectively. After adjusting for by-product credits, unreported discoveries and likely growth in resource, the unit discovery cost for the region was US$199/oz (compared to a world average of US$50/oz). For comparison, the unit discovery costs for the previous decade were US$55/oz and US$25/oz respectively. The region’s unit discovery cost for copper was US$0.036/lb (versus a world average of US$0.040). For comparison, the unit discovery costs for the previous decade were US$0.026/lb and US$0.008/lb Cu respectively.The region’s mediocre discovery performance doesn’t reflect its distribution of known mineralisation. Some countries within the region have a very good endowment per square kilometre.It is noted that the intensity of exploration (and resulting success) would be boosted if governments provided a more mining- and investment-friendly business environment and generated better precompetitive geological data sets (to identify new exploration targets and boost the country’s perceived mineral prospectivity). A multivariable regression analysis of a decade of data from the Fraser Institute’s mining company surveys found that a ten point increase in the Policy Perception Index or a 0.1 point increase in the Mineral Potential Index could boost (in the short term) exploration expenditures by 1.9 per cent and 2.7 per cent respectively. The resulting economic benefits of an expanded mining sector would be significant. The same story applies elsewhere in the world.CITATION:Schodde, R C, 2015. Discovery performance for gold and base metals in the Pacific/South-East Asia – 2005–2014, in Proceedings PACRIM 2015 Congress, pp 25–34 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By H. Askari-Nasab, B. Osei, K. Awuah-Offei

The U.S. coal mining industry consumes approximately 142 billion kWh/a of energy. The U.S. Department of Energy estimates that the industry’s annual energy consumption could be reduced by 49%. This constitutes nearly $3.7 billion of potential savings on coal production costs at 5.3¢/kWh of energy. Additionally, with climate change regulation on the horizon, any benefits from energy savings in the near future are compounded by associated reductions in CO2 emissions. Research indicates that operating conditions significantly affect energy efficiency. Modeling and simulation have been shown to be a cheap and reliable means of evaluating the effects of process interactions and operating conditions. The goal of this work was to apply stochastic process simulation to model the energy efficiency of a typical truck-and-shovel mining system and use the model to evaluate production strategies to improve energy efficiency. The research team conducted energy audits of truck-and-shovel overburden removal and used the results to develop regression models describing truck and shovel fuel consumption. The team then built a stochastic simulation model of the truck-and-shovel overburden removal operation and used it to assess a variety of improvement measures by simulation experimentation. Valid fuel consumption models for shovel loading and truck haulage have been formulated, based on the energy audit results. Valid stochastic process models of truck-and-shovel operations have been formulated to study energy efficiency. The following strategies, in decreasing order of impact, provide the most energy savings for truck-and-shovel overburden removal at the mine: (1) shorten haul roads, (2) increase shovel capacity and (3) increase shovel utilization through optimal truck matching. Additional data will be required to adequately describe operator effects on energy efficiency.

Jan 1, 2011

By Wei Ye, Lei Li, Xianjian Guo, Feng He

The purpose of the paper is to study the smelting process of copper concentrate with high Cu/S ratio produced in Africa or other areas around the world and theoretically analyze the influence of slag type on the smelting process. The paper has compared the processes used successfully in smelters, including CAPEX and OPEX and other factors, to provide reference for the industry to select the best process under specific conditions. INTRODUCTION At present, a great amount of copper concentrates with high Cu/S ratio, with chalcocite being the major source of copper, have been produced or are about to be produced in the Copperbelt in Africa and other countries in the world. The copper concentrate is usually high in copper (~30–55wt.%) and low in sulfur (~10–15wt.%). The conventional processes of smelting-converting and roasting-leaching-electro-winning for treating this type of concentrate is high energy and materials consumption such as electric power\fuels\flux et al. The direct-to-blister (one-step) smelting process can be considered favorable due to a reduction in processing steps. Up to now, there are four copper smelters in the world operating with the direct-to-blister smelting process. There certainly are problems in the process such as high copper content in the slag, strict operation requirement of slag cleaning electric furnace, etc. Except technical issues, the impact of factors on economical aspect such as power and material cost needs to be considered comprehensively in process selection. In this paper the technical issues of direct-to-blister smelting process, including slag treatment process, were analyzed and the comparison to the conventional processes and economic analysis of direct- to-blister smelting process to treat high Cu/S ratio concentrate were done.

Jan 1, 2019

Since the 1989 Loma Prieta Earthquake in the San Francisco Bay Area, the California Department of Transportation (CALTRANS) has accelerated seismic upgrading of their bridges. Many structures can be improved with the simple addition of hinge seat restrainers. Others require modification of column bents and superstructure to column connections. Often, footing retrofits are necessary, which require the addition of tension/compression elements (compression piling and tiedowns anchors) to resist overturning moments substantially larger than those originally used for footing design. These footing retrofits may include doweled reinforced concrete footing extensions or new pile caps which transmit forces to either driven steel or drilled concrete piles. In some cases, installation of these traditional piling elements is expensive, impractical or impossible due to: low overhead clearance, ground obstructions, high water table, noise or vibration sensitivity, or the inability to laterally expand the existing plan dimensions of the footing. In the latter case, one practical option is to attach small diameter drilled and grouted tension/compression piling elements (Pin Piles) to the existing footing. The footing may be strengthened with dowels and added concrete thickness or there may be a reduced shear span due to the installation of larger or jacketed columns. A reduction of elements is available with a Pin Pile alternative, particularly when the selection of traditional standard piles is governed by the reduced tension/uplift capacity available from the traditional elements, since Pin Piles exhibit superior uplift performance.

Jan 1, 1993

By Raymond D. Sloan

During 1944, substantial gains were recorded in practically every phase of the petroleum industry in Oklahoma. With the spotlight of activity focused on other states during the more recent years, the production momentum that was achieved in Oklahoma through the discovery and development of such outstanding pools as Oklahoma City, Fitts. and major pools in the Seminole area during the late 1920's and early 1930's was practically spent by the end of 1943. However, with much of the industry's exploratory efforts greatly reduced in Illinois, Indiana and Kentucky, the strong demand for Mid-Continent crude and the optimism created by some discoveries in the state toward the end of 1943, Oklahoma has again become the recipient of much activity and interest, with its 1944 drilling activity, production and refinery runs to stills registering substantial gains over the preceding year. Development and Exploration Since the discovery of the West Edmond pool in April of 1943, with the substquent drilling and development boom, the scene of exploratory activity has shifted from the central. south and east portions of the state to the general trend of the . Granite Ridge, where leasillg and wild-catting were greatly activated within a wide radius of this high subsurface feature. Leasing activity, however, jumped the confines of the Granite Ridge trend and extended into all of the northwestern counties in the state. Seismograph activity at once began following and keeping pace with this shift in the leasing and exploration locale, by the concentration of a large number of seismograph crews in the area. At one time during the year,35 crews were concentrated in Oklahoma, the majority being west of the Granite Ridge and extending into the northwestern counties. To illustrate the increase in geophysical work done in the state during the year, records indicate that 377 crew months were worked in 1944, which is a 21 per cent increase over the 311.5 crew months activated in 1943. With the discovery in 1943 of several encouraging prospects and the finding of West Edmond as an incentive, drilling operations increased some 54.3 per cent, for a total of 1986 completions during the year. This is compared with a figure of 1287 for wells drilled in 1943, an increase of 699 wells. The industry, with a total of 1064 oil producers, enjoyed a success percentage of 53.6 per cent. Gas wells completed were 223, while 699 dry holes were drilled. In 1943, completions included 587 oil wells, 127 gas wells, and 573 dry holes. The number of oil producers completed during the Year was almost double the numher of wells in 1943. Of the total drilling wells completed in the state, 350, or 17.6 per cent, were wildcat operations—an increase of 5.1 per cent over the 194.3 total of 333. The wildcat success percentage was 13.4 per cent, 47 successful wells being completed for an average initial potential of 160 bbl. In the state, 23 gas wells were completed with an average initial production of

Jan 1, 1945

By Shengli Wu, Wei Huang, Xinliang Liu, Kaifa Zhang

The slagging behavior, the phase of primary blast furnace slag and its transformation law of structure for the single furnace burden were studied in this paper. The results showed that the formation of primary slag was controlled by CaO/SiO2, Al2O3 content, MgO content, reducibility, iron content and porosity of the furnace burden. Fayalite (2FeO•SiO2) was easily formed from acid ferrous furnace burden while kirschsteinite (2(Fe,Ca)O•SiO2) was produced from alkaline ferrous furnace burden

Jan 1, 2015

By B. S. Lement

No appreciable stabilization of the austenite-martensite reaction occurs in a 15 pct Cr-0.7 pct C steel unless some martensite is initially present. Stabilization is induced by interrupting the subcool below M,; however, disappearance of the stabilization effect as manifest by burst formation of martensite may occur on continued holding at the final subzero reaction temperature. The higher the temperature of intermediate cycling after the initial subcool, the more permanent is the stabilization effect at the final reaction temperature. Appreciable conditioning of retained austenite occurs on reheating to about 500°C. These phenomena are explainable on the basis of the reaction-path theory. A RECENT investigation' carried out by the authors has shown that isothermal transformation of austenite to martensite definitely takes place in a 15 pct Cr-0.7 pct C steel and that appreciable amounts of martensite can form in this fashion. Investigations2-" arried out on other steels and iron alloys make it seem probable that isothermal formation of martensite is a phenomenon of fairly general occurrence. The reaction-path theory of Cohen, Machlin, and Paranjpe5,7 explains isothermal transformation on the basis of thermal activation of strain embryos which generate martensite plates with a velocity approaching that of sound. On the other hand, the nucleation and growth theory of Fisher, Hollo-mon, and Turnbull8 egards isothermal transformation as due to growth of athermally formed martensite nuclei. The experimental evidence obtained thus far favors the reaction-path theory in that the martensite reaction seems to be nu-cleation-controlled rather than growth-controlled. Stabilization is another phenomenon of importance with respect to the austenite-martensite reaction. According to the reaction-path theory, stabilization is a result of relaxation of strain embryos. It is postulated that strain embryos are present at the austenitizing temperature in the form of dislocations or lattice imperfections in the austenite which vary in the extent to which the lattice is displaced along the strain reaction path leading to martensite. On quenching from the austenitizing temperature, athermal martensite starts to form as soon as the M. is reached, because the activation energy of the transformation which decreases with decreasing temperature is lowered to below the level of the highest energy strain embryos. Martensite plates are generated during the cooling below M, from embryos possessing energies above the activation energy corresponding to the temperature at which the cooling is stopped. The distribution of lower energy embryos is changed because of the elastic and plastic strains produced in the remaining austenite as a result of the transformation. This effectively increases the number of strain embryos at all levels of energy below the activation energy and tends to stimulate further martensite formation either iso-thermally or on subsequent cooling. However, if the temperature at which the cooling is stopped is high enough for relaxation of strain embryos to occur, some degree of stabilization against further transformation may be induced. Whether stabilization will be observed on subsequent cooling will depend on the extent of decrease of activation energy with temperature. If the activation energy decreases sharply with temperature, it is possible that transformation will appear to continue with decrease in temperature in spite of the loss of embryos by relaxation. However, with a more gradual decrease in activation energy, stabilization will be manifest by no further transformation on cooling over a measurable temperature range until the

Jan 1, 1954

IT is very difficult for a founder engaged in jobbing work, comprising all sizes and classes of castings, to appreciate that the analysis of the iron he is using cannot entirely fill the situation he desires for his varied classes of work. Neither is there any panacea in the shape of an iron mixture that will suit the whole of his floor for the day.From his own experience he generally alters his cupola charges during the cast, endeavouring to meet at the same time the requisite metal composition for the castings he is about to pour.The founder on repetition work is in a much better position to stabilise his methods, arrive at a certain pig-iron' analysis, regulate...

Jan 1, 1926

By Zefang ChenLi, Laijun Ma, Lei Mao, Fang Lian

"In our work, the preparation technique of high pure manganese sulfate directly from low-grade rhodochrosite ore (MnCO3) was studied and improved intensively, including the effective leaching process and the short purifying process. Based on the same ion effect, the repeated leaching of rhodochrosite with sulfuric acid is proposed to improve the solubility of Mn2+ and inhibit the dissolution of the impurities Ca2+ and Mg2+. Moreover, the repeated leaching process could make full use of rhodochrosite and lower the dosage of sulfuric acidas raw material. With the aid of theoretical calculation, Ba(OH)2 was chose to adjust the pH value of manganese sulfate solution, and BaF2 to remove Ca2+ and Mg2+completely in the process of purifying. The results demonstrate that the extraction ratio and the recovery ratio of manganese reached 94.3% and 92.7%, respectively, which shows the prospect of industrial application. In manganese sulfate production, the heavy metal impurities have been decreased to less than 1ppm. Moreover, the content of calcium, magnesium and sodium has been decreased to less than 20ppm, which meets the standards of high pure reagent for energy and electronic materials. Our study enlightens an approach to the sustainable application of low-grade rhodochrosite.Introduction Low-grade manganese carbonate ores (=14%) becomes gradually the main resources for exploitation and applications in China according to national mineral resources survey (Tan et al 2004 and Singh et al 2017). Therefore, the electrolytic deposition technique of rhodochrosite faces great challenges including low electrolysis efficiency, high-resource input and high-pollution discharge (Fu et al 2010, Michelis et al 2009, Zhang et al 2013). Recently, more and more amount of manganese series with high or super high purity such as MnSO4, MnO2, Mn3O4 and MnO is demanded with the development of energy and electronic materials. Due to low-grade ores containing multiple elements such as iron, silicon, calcium and magnesium, conventional preparation of manganese sulphate with high purity from electrolytic product is characterized by long production-cycle and high-energy consumption (Subrat et al 2011, Mpho et al 2013). By contrast, hydrometallurgical method combined with thermal decomposition, hydrothermal synthesis and sol-gel processes has been widely studied because of its high efficiency, low consumption and low cost (Chen et al 2008). But the key problem in direct preparation of manganese series form low-grade rhodochrosite is to remove completely the multiple impurities such as iron, silicon, calcium and magnesium (Liu et al 2014). So it is urgent to develop a sustainable alternative approach with character of short process, high efficiency and environmental friendly."

Jan 1, 2017

By S. Dessureault, J. Porter, M. Woodhall

Information and communication technology (ICT) is seen as a key source of future productivity improvements in mines. The information technology infrastructure (ITI) necessary to achieve these productivity improvements will come in the form of data integrated from multiple source systems throughout the mining value chain. Two pure approaches are available: supplier-controlled or operations controlled data structures; each strategy has its own advantages and disadvantages. Case studies involving the South African mining industry are used to demonstrate the advantages of using hybrid-controlled data structures. Depending on the level of operational control, new skills are also necessary to be learnt by mining professionals including: information engineering; creating consistent and quality data; and process improvement techniques that use the integrated data for improving the operation.

Jan 1, 2004

By J. J. Zimmerman

Over-exposure to noise remains a widespread, serious health hazard in the U.S. mining industries. Most other categories of illnesses and injuries associated with mining have improved, with the exception of hearing loss. Mine Safety and Health Administration (MSHA) coal noise data from 2000-2004 show that the continuous mining machine is first among all equipment with 35% of the noise overexposures. Joy Mining Machinery, in collaboration with the National Institute for Occupational Safety and Health (NIOSH), is conducting research to reduce noise generated by continuous mining machines. This paper describes a ?JOY Designed for Noise Reduction? (JOY-DNR; Patent Pending) tail section as a noise control for reducing the noise overexposures of continuous mining machine operators. Underground results show a 45% and 65% noise exposure reduction for the operator when compared to a standard machine. Utilizing this newly developed noise control, along with previously proven controls, will provide continuous mining machine operators an opportunity to be within the MSHA-Permissible Exposure Limit (MSHA-PEL).

Jan 1, 2010

By Deborah Muggli

Minera Escondida is the world's largest copper mine. Its capacity is more than 800 kt/a (880,000 stpy) of copper. The Escondida open-pit mine operates at an elevation of 3,100 m (10,170 ft). It is located in the Atacama desert about 160 km (100 miles) southeast of the port of Antofagasta. At Coloso, 14 km (8 miles) south of Antofagasta, copper concentrate is dewatered by filtration for storage and shipment to overseas markets (Fig. 1). Concentrate filtrate water, after being treated to remove suspended solids, is discharged at 60 m (200 ft) depth into the Pacific Ocean. This effluent is free of particulates. However, it does contain metal levels above US Environmental Protection Agency (EPA) receiving water criterion. EPA standards are more strict than Chilean receiving water guidelines. However, a multiport diffuser provides rapid mixing of sea water with effluent to ensure metal levels in the receiving water remain below EPA receiving water guidelines. The Escondida Mine began operation in December 1990 at a rated mill capacity of 35 kt/d (38,500 stpd). Since then, the complex has since undergone three expansions. In 1996, it processed 115 kt/d (127,000 stpd) of ore. At Coloso in 1993, about 25% of the copper concentrate was fed to an ammonia leach plant for solvent extraction and electrowinng of cathode copper. This plant is designed to produce 80 kt/a (88,000 st/year) of cathode copper. In 1995, the ocean diffuser system's capacity was doubled to accommodate increased flows to a maximum 50 L/sec (793 gpm). This was achieved by extending the diffuser chamber by 32 m (105 ft) and adding 16 nozzles, which doubled the diffuser's capacity. In November 1996, Rescan Environmental Services began a field verification of the outfall/diffuser system's performance. The study's objective was to determine the performance of the outfall/diffuser system by measuring dilution factors using fluorescent Rhodamine dye and to determine if copper concentrations are below the US Environmental Protection Agency (EPA) water quality criterion of 2.9 µg/L total copper (EPA, 1986). Rhodamine dye was injected into the outfall/diffuser system. An oceanographic survey using an in situ fluorometer was conducted to measure dye concentrations in the effluent plume. Water column characteristics were also measured. These included current speed and direction.

Jan 1, 1997

By Arthur T. Ward

WHEN the Board of Directors of the Institute in June 1931 approved the formation of the Committee on Eastern Magnetite and its then membership of eleven, little did any of those concerned envision that twelve years later the annual Committee luncheon would attract 34, and the technical session, jointly with the Iron and Steel Division, more than 70. Yet that was exactly what happened during the February meeting just passed. And what is more important, some members of the Committee are now predicting that by 1944 over 10 per cent of the iron ore produced in the United States will come from these Eastern Magnetite properties. Chairman Crockett, in opening the meeting, advised that due to the serious illness of Meredith E. Johnson, State Geologist of New Jersey, Mr. Johnson would be unable to brief his scheduled paper, which would therefore be reserved for a later date.

Jan 1, 1943