Search Documents

By Qingzhu Li

The adsorption process of Pb2+ from aqueous solutions by spent grains modified with Imol/L NaCI solution was investigated. The effects of solution pH, contact time, adsorbent concentration, initial Pb2+ concentration, particle size on Pb2+removal were also studied. The initial adsorption process was rapid and 90.35% of Pb2+ adsorption occurred within 30 min. The absorption equilibrium was obtained at 4h. When pH was 5.5, Pb2+ concentration in aqueous solutions decreased from the initial content of 20 mg/L to 0.0 I mg/L after 5 hours by application of IOg/L adsorbent at 25?C, Pb2+ removal efficiency reached up to 99.95% and the Pb2+ remaining in aqueous solutions was under China Sanitary Standard for Drinking Water (GB5749-85). Adsorption data fitted well with Lanf+muir and Freundlich models. However,Langmuir isotherm model was better to descnbe Pb- adsorplion than Freundhch model, mdlcatmg that the applicability of monolayer coverage of Pb2+ on the surface of adsorbent.

Jan 1, 2008

Iron ore in the Middleback Range area has a density and susceptibility contrast with adjacent rocks, and gravity and magnetic methods are applicable to exploration for it. The gravity method is satisfactory whether the ore mineral is hematite, magnetite, or limonite; the magnetic method is suitable for detecting ores which contain magnetite, such as some hematite ore, magnetite ore, and possible ore in the form of magnetite-bearing schists. jaspilites, and carbonate rocks.Geophysical exploration began in 1948 and is still in progress. The methods which have been used are aeromagnetic (83 per cent), ground magnetic (13 per cent), gravity (3 per cent), and others (1 per cent). Ground magnetic surveys have been made wherever aeromagnetic surveys recorded large anomalies. The gravity method is being used to investigate those parts of the area considered most favourable for ore occurrence.Qualitative and quantitative interpretation of the geophysical data has been made and the rocks causing selected anomalies tested by bores.Magnetite in the Middleback Group rocks produces the major magnetic anomalies in the area. The average magnetite content of magnetite-jaspilite, which is the commonest rock type, is 33 per cent by weight and that of magnetite-carbonate at the Iron Duke-Iron Duchess is 50 per cent. These rock types also contain hematite and the average total iron content of the former is 35 per cent and of the latter 50 per cent.INTRODUCTIONThe geology and iron ore resources of the Middleback Range area were described by Miles (1954). Since 1954, much drilling, mapping, and quarrying has been done but there is no published report of this work.The rocks which constitute the Middleback Range, Camel Hill-Cooyerdoo line, Katunga Hill-Iron Knob, and Ash Range (Fig. 1) belong to the Middleback Group of Middle Precambrian or late Archaean age. Most outcrops of the Group are jaspilites, formerly called banded hematite (or magnetite) quartzite. The high grade hematite deposits...

Jan 1, 1964

By Harwant Singh

El presente texto describe la geología médica como un recurso de iderazgo ambiental. Así también se describe el medio ambiente, los procesos micronivelados y los componentes del sistema Tierra.

Sep 1, 2012

By Benoit Virollet

Over the last 10 years the diameter of unbraced, unlined and unanchored circular shafts has grown dramatically in many parts of the world. This progress has taken place through improvements in: construction methods; concrete rheology; and design capabilities. Excavation equipment has become more precise in terms of operator control and ability to correct alignment of digging elements leading to better alignment tolerances. Also contributing to the increases in shaft diameters is the evolution of design models. A better understanding of soil structure interaction is being incorporated into the analyses in terms of radial soil stresses and imposed loads on the shaft. This paper provides an overview of the recent progress made in circular shaft construction, the primary design considerations, and some innovative uses of efficient arc elements to develop unsupported structures of other shapes. In addition, a summary of recent circular shafts constructed worldwide is provided.

Jan 1, 2006

By H. P. Reid

PORTLAND cement is manufactured under either of two general proc-esses, the wet or the dry. The raw materials in general consist of limestone, shells, marl, cement rock, clay, shale, blast-furnace slag, etc., so proportioned that when calcined the desired composition will be obtained. In the wet process the combined raw materials are ground to extreme fineness in the presence of water, to a resulting slurry of from 30 to 50 per cent moisture content. The moisture of the slurry may be reduced by thickening or filtering processes for feed to the cement kiln or the slurry may be fed to the kiln with its full percentage of water. The dry process differs from the wet in that the surface moisture of the raw materials is removed prior to grinding. For the drying of these materials heat is required and in most cases is produced by burning of raw fuel either on grates or stokers before the dryers or in suspension in the form of pulverized coal, oil or gaseous fuel. The power required for making the cement is sometimes purchased from outside sources; sometimes it is generated from the heat in the waste gases leaving the cement kilns, or generated at the plants direct from raw fuel. We have, then, as the possible requirements of fuel in the cement industry: (1) fuel for power generation, (2) fuel for drying raw materials, including coal before pulverizing, and (3) fuel for burning the raw materials to cement clinker. There is no essential difference in quality required in fuel for burning the materials by the wet and dry processes.

Jan 1, 1932

By Arthur Bell

(San Francisco Meeting, September, 1915) . PRIOR to 1908 the oil production in the State of California, had been almost entirely a heavy fuel, oil, with a high flash point, hut changed within a-short period to a large percentage of refining oil with a low flash, by reason of the coming in of the Santa Maria field, the Midway field, and the increased production of the Fullerton field. This is clearly shown in the following tabulation of California's production: Year Barrels . Below -20° Be, Above 20° Be,, Per Cent_ Per Cent. 1905 48,307,000 90 10 1910 77,698,000 SO 20 1912 90,075,000 6o 31 1914 10:3,600,000 47 53 The bringing in of these high percentage's of light oil with their dangerous low flash and the increasing demand for the refined products necessitated the devising of some cheap and efficient means of quickly separating the lighter elements either in the field or at the main distributing points; also it became necessary to remove the excessive percentage of water which many of the light oils carried in emulsion.

Jan 9, 1915

By Frank H. Macpherson

When it became apparent early in 1941 that the United States might be drawn into the war, studies were made of the bauxite situation in Arkansas, principally because 9.5 pct of the known bauxite reserves of the country were located in that State. Bauxite mining was then geared for maximum production to supply ore to meet this country's war requirements and, if necessary, to supply the needs of Canada as well. In view of the comparatively small bauxite reserves, Congress appropriated funds for an extensive exploratory drilling program to be carried out by the Bureau of Mines in cooperation with the Geological Survey. An alumina plant was erected near Bauxite and an aluminum plant near Hot Springs, Ark., by the Defence Plant Corp. The Metals Reserve Co. established a schedule of prices, arranged for stockpile sites and a buying agency. Operators cooperated to step up production and new ones came into the field. Production Record Prior to 1941, the greatest annual production in Arkansas was 562,892 long tons, dry basis in 1918. During the single month of August 1943, 693,596 long tons were mined—130,704 tons more than for the entire year of 1918. In general the Arkansas bauxite deposits are relatively small, irregular in thickness, somewhat scattered and, compared to coal, iron or open-pit copper deposits, are ill-adapted to an expansion in output. Commercial deposits range in horizontal extent from less than an acre to about 40 acres and are usually very irregular in outline. The average thickness of all known workable deposits is between 12 and 15 ft. with a maximum of about 60 ft. The ore bodies are usually somewhat undulating and nearly horizontal although locally some deposits dip as much as IS°. Types of Bauxite Three physical types of bauxite may be recognized: pisolitic, granitic and amorphous. Pisolitic ore is the most common type. It consists of small pebble-like nodules, ranging from the size of a pin head up to several inches in diameter, all set in a fine grained matrix. Transported bauxite is usually- pisolitic. Most residual bauxite is granitic. It is believed not to have moved appreciably from the location where it originally was formed. This is indicated by the fact that it appears to grade into unaltered nephelite syenite, which it overlies. Amorphous ore is the least abundant. It is nonpisolitic and resembles clay, has no characteristic texture, and can be identified definitely only by chemical analysis. Uses of Bauxite Bauxite is chiefly used for, and at the present time is substantially the only

Jan 1, 1948

By Frank H. Macpherson

When it became apparent early in 1941 that the United States might be drawn into the war, studies were made of the bauxite situation in Arkansas, principally because 9.5 pct of the known bauxite reserves of the country were located in that State. Bauxite mining was then geared for maximum production to supply ore to meet this country's war requirements and, if necessary, to supply the needs of Canada as well. In view of the comparatively small bauxite reserves, Congress appropriated funds for an extensive exploratory drilling program to be carried out by the Bureau of Mines in cooperation with the Geological Survey. An alumina plant was erected near Bauxite and an aluminum plant near Hot Springs, Ark., by the Defence Plant Corp. The Metals Reserve Co. established a schedule of prices, arranged for stockpile sites and a buying agency. Operators cooperated to step up production and new ones came into the field. Production Record Prior to 1941, the greatest annual production in Arkansas was 562,892 long tons, dry basis in 1918. During the single month of August 1943, 693,596 long tons were mined—130,704 tons more than for the entire year of 1918. In general the Arkansas bauxite deposits are relatively small, irregular in thickness, somewhat scattered and, compared to coal, iron or open-pit copper deposits, are ill-adapted to an expansion in output. Commercial deposits range in horizontal extent from less than an acre to about 40 acres and are usually very irregular in outline. The average thickness of all known workable deposits is between 12 and 15 ft. with a maximum of about 60 ft. The ore bodies are usually somewhat undulating and nearly horizontal although locally some deposits dip as much as IS°. Types of Bauxite Three physical types of bauxite may be recognized: pisolitic, granitic and amorphous. Pisolitic ore is the most common type. It consists of small pebble-like nodules, ranging from the size of a pin head up to several inches in diameter, all set in a fine grained matrix. Transported bauxite is usually- pisolitic. Most residual bauxite is granitic. It is believed not to have moved appreciably from the location where it originally was formed. This is indicated by the fact that it appears to grade into unaltered nephelite syenite, which it overlies. Amorphous ore is the least abundant. It is nonpisolitic and resembles clay, has no characteristic texture, and can be identified definitely only by chemical analysis. Uses of Bauxite Bauxite is chiefly used for, and at the present time is substantially the only

Jan 1, 1948

By G. L. Smit

The Buffelsfontein Gold Mining Company is situated in the Klerksdorp district of the Province of the Transvaal in the Republic of South Africa, approximately 100 miles west of Johannesburg. Gold production commenced in January 1957 and Uranium treatment of residue slimes as a by-product started in July 1957. The mining property is 5435 mining claims in extent, the equivalent of 7988 acres or 12.5 sq miles. The mine was initially exploited by the Pioneer Twin Shaft System, consisting of a 26-ft diam down-cast shaft and a 22 ft-diam up-cast shaft, sunk in the north-west area of the mine to cater for the hoisting and ventilation requirements for a milling rate of 150,000 tons per month. To exploit the Eastern zone of the property and assist in increasing production to 200,000 tons milled per month, it was decided to sink a further Twin Shaft System consisting of a 28-ft diam downcast shaft and a ventilation up-cast shaft -22-ft in diam, both monolithic concrete lined — 200 ft apart and 5300 ft deep. This paper deals with the sinking and commissioning of these Eastern Twin Shafts. This was achieved by one sinking crew within a period of 20 months. A) PLANNING 1) Siting: The Eastern Shaft System was sited in the north-east area of the property, 12,000 ft east on strike from the Pioneer System. (Fig. 1). Initially the system was sunk to the 5300 ft elevation to conform with the original Pioneer Shaft System. On completion a sub-vertical main shaft will be sunk to the 8000 ft elevation in the immediate vicinity, and subsequently the surface ventilation shaft will be deepened to this elevation by raising from level to level and sliping to full size. The exact positions of the shafts were chosen after: a) underground development had located certain known water bearing zones, and b) geophysical and topographical surveys had been carried out. The shafts passed through the following geological succession: Surface to 4430 ft - Dolomites of the Transvaal System 4430 to 4470 ft - Quartzites and conglomerates of the Black Reef Series of the Transvaal System. 4470 to 4470 ft - Diabasic Lava of the Venters-dorp System (Ventersdorp Contact Reef at base). 4470 to 5250 ft - Quartzites of the Elsburg Series of the Upper Witwaters-rand System. The shafts were sited to ensure that the least possible water would be encountered during sinking, and this contributed to the rapid rate of sinking. 2) Duties: a) The 22-ft diam ventilation shaft was designed to up-cast 1,400,000 cfm of air (0.060 density) against a resistance of 22 in. water gauge. b) The main shaft was designed to handle 160,000 tons hoisted per month as well as the men, material and down-cast ventilation to serve this tonnage. The 284 diam main shaft is equipped with streamlined buntons spaced at 15 ft centers set in pockets which were left during sinking. There are six compartments, four of which are sewed by two dual purpose hoists, hoisting either, twedeck man cages or 13-ton bottom discharge skips. The other two compartments are served by a single purpose winder hoisting double deck cages accommodating 60 men per deck. (Fig. 2). 3) Timing: Permanent equipment was ordered well in advance to insure continuity in the operation. Development underground reached the shaft positions before the start of sinking operations. From this development, boreholes were drilled into shaft positions to drain off water in the vicinity of the shafts. To ensure complete co-ordination of effort, all relevant data, as well as the allocation of responsibility, were made known to all persons and departments concerned. 4) Models: The extensive use of scale models during the preliminary planning stages proved most useful in deciding on design such as buntons, bunton pockets and guide cleats, and complex layouts concerning loading, spillage and pumping arrangements. (Fig. 3). These models also proved invaluable in determining the walling routine. Normal working conditions could

Jan 1, 1964

By C. C. Hagenbuch

Machine loading of coal into mine cars is increasing rapidly. Particular reasons for its use frequently apply to certain localities, but in general, it is profitable to install mechanical coal-loading equipment: (I) when existing hand-loading contract rates prevent further cost reduction; (2) when the height of the coal bed requires that either top or bottom must be taken to place cars in rooms; (3) when labor shortage or limited house-plant capacity prevents the production of desired tonnage ; (4) when tonnage requirements are in excess of possible hand-loaded production from developed areas; (5) when working places are scattered and it is possible to concentrate production, and therefore supervision, by the installation of mechanical equipment; (6) when rapid development is essential. Having decided to install loading equipment, the problem then arises as to what type is best adapted for a particular mine or coal bed, the choice lying between mobile track equipment, pit-car loaders, scrapers, shaker conveyors, belt conveyors and drag conveyors. MajoR FactoRs Influencing Choice of Equipment In determining the type of equipment to be used, the following major factors must be studied: Grades.—Adverse grades, while permitting other types of loading equipment to work successfully, may prevent the success of a shaker conveyor installation. Thickness of Bed.—The thickness of coal governs the choice of equipment. A machine that requires 5 ft. of head room should not be selected for a 3-ft. bed where otherwise it would be unnecessary either to brush top or to lift bottom. Nature of Pavement.—Soft or scaly bottoms are unsuitable for the use of any type of digging loader, shaker conveyors or scraper loaders. nigging loaders and scraper loaders scale the bottom, mixing it with the coal and causing preparation difficulties; shaker-conveyor drives frequently work themselves loose, destroying the conveyor alignment and creating maintenance problems. Nature of Roof.—With any type of loading machine, it is policy to obtain the maximum possible tonnage per move per set-up. This must

Jan 1, 1931

By A. M. Richardson

The significance of a massive sandstone unit in the immediate roof to longwall support weighting is well known. If the unit lies in the main roof above the zone of caving, its influence becomes more difficult to calculate using traditional methods. Much of the reserves at Cyprus Plateau's new, multi-seam Willow Creek Mine are located in the A Seam. The massive Kenilworth Sandstone is typically situated 21.3 m (70 ft) above the A Seam in the main roof and is on average 14.6-m (48-ft) thick, ranging to 29.0-m (95-ft) thick. This paper describes the application of distinct-element modeling to determination of the appropriate yield capacity for supports at Willow Creek. The modeling was determined to be useful for understanding support loading mechanisms and as an aid to engineering judgment in selecting supports.

Jan 1, 1996

By Brent A. D, Olsen a. H, Mayfield P. L J, Grazier P. E

Concentrates produced from MnO2 and Fe203 ore fines have been targeted as potential feedstocks for direct metallurgical processing. Prereduction of pyrolusite-rich Mn02 sands to MnO has been investigated in batch and continuous experimental bubbling fluidised beds using CO-H2 reducing gas mixtures. This process has been found to produce a high grade feedstock suitable for smelting to ferroalloys or acid digestion for chemicals production. Similarly, production of highly metallised direct reduced iron (DRI) from hematite ore fines has also been investigated in batch bubbling bed reactors. Programs to characterise the reduction kinetics, fluidisation behaviour and defluidisation phenomena for both feedstocks are currently in progress to enable optimum process conditions to be determined.

Jan 1, 1995

By M Dale White

In December at the Commonwealth of Kentucky Fifth Annual Blasting Conference of the Division of Explosives and Blasting, Department of Mines and Minerals, I delivered a paper entitled "Problems on Blasting Insurance. " Donald H. Matthews, President of Explosives Engineers, Inc. located in Sparks, Maryland came up to me before the program and said, "We explosives users know what the problems are. What we need is someone who can solve those problems. "

Jan 1, 1979

By Donald C. Strimbeck

The Bureau of Mines designed a down-fired refractory-lined combustor that efficiently burned pulverized coal to produce a gas suitable as working fluid for an open-cycle gas turbine. The gas contained relatively little carbon, so the load on the ash-separation equipment was significantly reduced. Moreover, reduction in carbon content of the gas increased the average density of the solid particles making them more amenable to removal by centrifugation. Centrifugal-type separators failed to remove sufficient ash; however, to limit blade wear enough to achieve operating periods generally deemed necessary for commercial practicability.

Jan 1, 1969

By Edward W. Parker

This plant was built in 1907 at the Bankhead mines to manufacture briquettes by the Zwoyer process under license from the Zwoyer Fuel Co., of New York, N. Y. The building was constructed to contain two units, each of a capacity of 10 tons per hr.; one unit was installed at the time the building was constructed, and the second unit is now being built. The coal used is an anthracite, which is more friable than that of Pennsylvania, and, as a consequence, a larger percentage of dust or waste is produced, which was formerly thrown upon the slack-pile as waste, but is now passed to the ? dust-bin " in the breaker, from which it is conveyed to the briquette-plant.

Jan 5, 1908

The objective in control blasting is to reduce overbreak to control the final pit wall slope, shaft, drift, ditch, bench, etc. to the final planned excavation limit.

Jan 1, 1991

By Jerry G. Craig

The Bureau of Mines has developed a computerized oil and gas well data retrieval system from studies of the waterflood potential of a producing reservoir. This system stores pertinent information about each well completed in a reservoir and facilitates selection and manipulation of large volumes of data. Use of the system enables reservoir information to be supplied rapidly, accurately, and at less expense.

Jan 1, 1971

By J. Dorsey

In 1910, Colonel Boyce Thompson, who owned Inspiration (now Cyprus Miami) and various other mining interests, formed the Magma Copper Company and leased the Silver Queen claims around Superior, Arizona. At the same time, he purchased other claims around the Silver Queen claims from what was then called the Magma Mine. The mine continued to operate until 1982 when Newmont Mining Company, who owned Magma Copper Company, shut down the operations due to high costs and low copper prices. When Magma was spun off by Newmont as an independent company in 1987, new studies of Superior were started. It was clear from these studies that the mine had been shutdown and over 1400 employees laid off for two basic reasons: first, as a resu1t of a mine plan that was technically flawed and second, be-cause of very high production costs mainly due to the low productivity from a very high cost work force. During 1989 a plan was formulated to re-open Superior with the determination to over-come the problems that resulted in closure. A new mine plan was developed and a management style developed that promotes team work and high productivity.

Jan 1, 1992

By PATRICK R. TAYLOR, NICHOLAS BELLUSCI, D. ERIK SPILLER, VICTOR BRAMAN

Most of the world’s production of natural soda ash comes from the mining and processing of trona found near Green River, WY. The processing of trona ores to ultimately yield a high-quality dense soda ash product and reject the insoluble gangue species, primarily in the form of oil shale, is water and energy intensive. It is speculated, however, that the glass-manufacturing industry, which is the largest consumer of soda ash, may be able to use product of a lower grade and consistent level of the insoluble constituents. Thus, the viability of using sensor-based sorting to produce a beneficiated trona stream that would be fed to calcination was investigated. The study encompassed the preparation of a run-of-mine (ROM) Green River ore sample; selection of specimens sized 25 to 75 mm; imaging of the specimens by sensors based on X-ray transmission (XRT), color and laser-induced fluorescence (LIF); insolubles analysis of the specimens; and a bench-scale sorting test. Results of the study established that a correlation between the color of the individual ore particles and their insoluble content exists, and that a surface-detection-based sensor, particularly LIF, is apparently more suitable than XRT to produce a beneficiated trona stream. The bench-scale sorting test demonstrated that a 65 percent separation efficiency and a 70 percent recovery of trona could be achieved.

Feb 1, 2023

By L. R. Raymond, J. L. Hudson

This paper proposes a comparatively short-term (8 to 10 hours) well test for detecting and characterizing well-bore damage and for measuring mean formation permeability. The proposed test is made by injecting fluid at constant pressure, recording injection rate as a function of injection time. After one to four hours of injection, the well is shut in and fall-off of bottom-hole pressure is obtained as a function of shut-in time. Formation permeability is estimated by an iterative technique. First, a value of formation permeability is assumed. Then, a plot of the recorded injection rate as a function of dimensionless time is made, using the assumed pertneability value. From the slope of the injection-rate curve. a new value of formation permeability is calculated. If the new value agrees with the original assumed value, the assumption was the correct formation permeability. If the values do not agree, the process is repeated using the new permeability value in the calculation. Convergence is rapid, and a reliable permeability value results. Pressure fall-off data are used to check the result. Graphs of pressure and injection rate us functions of time given in the paper show that changes in permeability of the formation in the neighborhood of the wellbore are disclosed by this technique. Thus, the short-term test can he used to detect formation damage. Also, a rough measure of the radial extent of damage can be inferred, which is helpful in designing stimulation treatments. The mathematical model used for this work was a single-zone, horizontal reservoir with a damaged zone in which permeability decreased continuously as radial distance to the wellbore decreased. This model is more realistic than the usual two-zone, discontinuous permeability model used in published works; calculations indicate the realistic model is valid. Vertical variations in horizontal permeability were studied with this model, and results indicate that the permeability measured by the short-term test is the mean horizontal permeability for the vertical interval tested. The proposed short-term test thus should be useful in detecting and characterizing formation damage and in measuring formation permeability needed in calculating reservoir transmissibility. INTRODUCTION To plan the most efficient production or injection schedule for a well and to design or evaluate the optimal stimu- lation treatment, it is necessary to know the properties of the reservoir adjacent to the well, particularly the reservoir transmissibility and characteristics of a damaged zone, if one exists. Several techniques for determining reservoir transmissi-bility from well tests have been presented in the literature. 1,2,3,4 All these techniques rely on conducting constant-rate well tests that often are difficult to execute. A constant-pressure well test is generally easier to carry Out. and this paper contains the first available method for the analysis of constant-pressure well tests. Determination of wellbore damage from transient well tests has been the subject of several papers."" From these studies it is apparent that information necessary for determination of the characteristics of a damaged zone is available shortly after the transient well test is initiated. Consequently, it may not be necessary to carry out an extensive well test (for example, a pressure build-up test) if the primary purpose of the test is to detect the existence of wellbore damage. All previous studies of well testing to determine wellbore damage have been based on the two-zone perrneability model. In this model the damaged zone has a permeability k,, extending to a radius r,,, and the formation permeability k obtains from r, to the drainage radius r,.. Consequently, there is a discontinuity in permeability at r = r,,. This discontinuity can be eliminated by assuming a continuous variation in permeability through the damaged zone. The effect of this assumption on transient well tests is discussed in following sections of this paper. In addition, all formations have within them vertical permeability variations associated with lithology changes throughout the zone of interest. This paper also considers the effect of these variations on transient well tests. ANALYSIS OF CONSTANT-PRESSURE WELL TESTS The mathematical analysis associated with the injection of fluid at constant wellbore pressure into a single-zone, horizontal reservoir completely filled with a fluid of small and constant compressibility and constant viscosity is given in Appendix A. In this analysis it is assumed that the well is located at the center of an undamaged, circular drainage area. From this analysis, the formation permeability can be obtained as follows. 1, Estimate a value for the formation permeability k. 2. Prepare a plot of injection rate q vs

Jan 1, 1967