Search Documents

By R. C. Milici

The primary factors that determine the marketability of coal from various supply centers in the U.S. are coal quality and supply; i.e. low sulfur, moderate- to high- Btu coals have large market areas when compared to less expensive but poorer quality coals. Price is the major factor in the competitive marketing of similar coal products. Good quality, (moderate- to high- Btu, low sulfur) coals from the Powder River and central Appalachian basins are marketed over large areas of the country, and central Appalachian coal is widely distributed in foreign markets, primarily as coking coal. In contrast, poorer quality bituminous coal (low calorific value and/or high sulfur) from the Illinois Basin, northern Appalachian Basin, and lignite from the Gulf Coast is marketed in or near the States in which it was mined even though the price at the mines may be lower than mine prices for central Appalachian coal. Widespread distribution of sub-bituminous Powder River Basin coal is enhanced by its exceptionally low mining costs, which offsets transportation costs to distant markets.

Jan 1, 2001

By D. Harrington

Approximately 6,000 coal mines are operated in the United States. All of them have in some degree the elements that are likely to contribute to an explosion, hence it is surprising that explosion disasters are not more frequent and that many mines have been operated for years and finally worked out and abandoned without experiencing an explosion. The absence of coal-mine explosions does not always indicate that effective efforts have been made to prevent them but rather that the nine has been fortunate in that the combination of circumstances necessary to cause an explosion has not existed. In view of present knowledge of the methods of preventing explosions, disasters are inexcusable and discredit the mining industry. The methods of preventing mine explosions are known to experienced, well-informed persons engaged in coal mining, yet despite this knowledge far to many coal-mine operators continue to use practices and methods that they should know have resulted in numerous explosions. Moreover, many mine workers persist in following past procedure irrespective of consequences and in breaking safety rules or indulging in practices almost certain eventually to result in disaster. Continued failure to apply known common-sense methods of accident and explosion prevention unquestionably will cell for ultimate enforcement of law.

Jan 1, 1940

By Michael Hood

High-volume, low-pressure water jets have been employed for erosion of loosely consolidated rocks for centuries. This excavation method finds application in specialized circumstances even today. The use of high-pressure, low-volume water jets for rock cutting is more recent and was made possible by the development of high-pressure water pumps. Despite the benefits often claimed for these systems, high-pressure water jets still have not found widespread application. In this report, the U.S. Bureau of Mines has reviewed the various methods that have been employed using water jets to break rock and has focused on one method, termed "jet-assisted cutting," which was determined to be the closest to commercial development. The current state of knowledge based on laboratory and field experiences using this cutting method is reviewed, and possible future developments for this approach to excavation are assessed.

Jan 1, 1990

By J. Cayouette, . Blatter, P. Cousin

The Laronde mill was commissioned in 1988 and has been treating the Laronde Perim ore since 2000. The Laronde plant, situated in the Abitibi region of Quebec, has experienced mill expansions to accommodate 7500 mtpd and to recover gold and silver as well as important amounts of base metals (Cu, Zn, Pb). Ten sequential metallurgical and environmental processes are responsible for metals recovery and process viability. Over 200,000 ounces of gold, 4,5 million ounces of silver, 7000 tonnes of copper, and 78,000 tonnes of zinc are produced annually. In 2008, the Goldex plant began trucking high wade (35-45 Wt Au) pyrite sulphide concentrate (TCGO) for gold extraction at a newly constructed treatment plant, increasing gold output at Laronde by 40,000 ounces. In 2009, the high gold wade Lapa ore processing facilities were annexed to the Laronde plant increasing output by 120,000 ounces of gold. TCGO and Lapa productions are forecasted until 2018 and 2015 respectively, with known reserves of each mine. Today, up to 140 permanent employees run and optimise the Laronde plant operation. As a result, Laronde has intricacies intrinsic to a large and varied operation. The paper will outline the metallurgical highlights, challenges, and future outlook related to the treatment of each ore type (Laronde, TCGO, and Lapa)

Jan 1, 2011

By Sabine Verryn, Johan de Villiers

"Through the application of the Rietveld method, X-ray diffraction analysis has developed into a fully quantitative method for phase analysis. The Rietveld method itself has progressed from an unstable method that required constant operator intervention to a stable and robust method suited even for routine analysis. The method however, requires a good initial calibration and periodic checks on its precision and accuracy.Several examples from minerals processing, pyrometallurgy, and materials science show the strengths and applicability of the method. The limitations and sources of error are also discussed.1. IntroductionDiffraction of X-rays by matter has been used for more than 80 years, initially to elucidate the structure of crystalline matter, and to investigate the bonding between atoms. The first development of powder diffraction cameras and the later development of X-ray diffractometers saw the development of methods to identify phases and to try to quantify them in mixtures. A comprehensive database and search-match techniques have been developed over the ensuing years. Effective and accurate quantification had to wait for the so-called Rietveld' analysis where the total diffraction pattern is used and where the crystal structure data for the constituent phases are needed as input. Overlapping of diffraction peaks of different phases is handled without difficulty and reliable results can be obtained in spite of this occurrence.The development of methods for structure analysis from powder data has also progressed rapidly and more and more complex structures are being solved from first principles, i.e. without knowledge of unit cell or space group data. Because of the ease of use of the Rietveld method, it is finding increased application in metallurgy, especially in the quantification of phases of importance in minerals processing, in pyrometallurgical processes, and in materials characterization. This study will examine the principles of the Rietveld method, its application in metallurgy, and finally also the common pitfalls that need to be avoided.2. Rietve1d AnalysisAs the Rietveld method compares the experimental diffraction pattern with one calculated from known crystal structure data, the following data are needed:•,An XRD Pattern with as Iowa background as possible. This should have good resolution and high diffraction peak intensities. With modem X-ray detectors, this can be achieved in minutes rather than hours.•,Instrumental parameters such as goniometer radii and slit sizes are needed. These are the so-called ""Fundamental parameters"". They are used to calculate the shapes of the resultant diffraction peak profiles that are caused by the instrument. The parameters are used to correctly separate the instrumental effects on the diffraction pattern from the sample effects."

Jan 1, 2014

By G. R. Waters

"The technology behind industrial applications such as Hydrometallurgy continues to evolve, as do the corresponding regulations and specifications that ensure the safety of workers and the environment. Valves make up key aspects of this technology, and often represent the single point of failure for entire operations. More often than not, the valves being used in Hydrometallurgy applications are known as Severe Service Valves (SSVs) due to their ability to withstand the extreme conditions. Most experts agree that SSVs are identified by applications, and that these applications are challenging to the valve’s ability to provide a minimum acceptable level of performance over a minimum acceptable duration. The Manufacturers Standardization Society (MSS) of the Valve and Fittings Industry has designated Ross Waters, President of CGIS, as Lead to the Task Force put in place to determine the minimum requirements a valve needs to be able to perform to when faced with extreme conditions, whether from pressure, temperature, toxicity, solids, or usage. This paper serves to determine what the minimum requirements are for SSVs in Hydrometallurgy applications. It will draw on five decades of industry experience from one of Canada’s leading valve experts.INTRODUCTION Severe Service Valves Severe Service Valves (SSVs) mean different things to different people. Until today, defining SSVs had little if any global agreement or recognition. That is about to change as the Manufacturers Standardization Society (MSS) has accepted an application to produce a Standard Practice so defining them. This paper provides information about the selection of SSVs in all industries but focusses on metallurgical processes and applications and offers examples to illustrate the successful and unsuccessful use of these valves. All of this with the purpose of raising the awareness of the industry on all sides, from the suppliers and manufacturers, specifiers and to the users and owners of them. It also supplies tools to understand where and why to separate SSVs from general purpose or commodity valves (GPVs). SSVs are often identified by applications, and these applications are challenging to the valve’s ability to survive. Within these applications the elements that make the service severe are being analyzed, quantified and qualified. From this, we expect to offer objective and repeatable definitions and guidance to improve the experience of SSVs, reduce unnecessary costs, provide longer service life and process runs, improve safety and reduce environmental issues."

Jan 1, 2017

By W. Smith, F. G. Rinker, D. Beggs

Early in 1965 the Surface Combustion Division of the Midland-Ross Corporation was awarded the contract to engineer and construct a taconite pelletizing plant for the National Steel pellet plant, administered by the Hanna Mining Co., near Keewatin, Minn. This plant, which will have an annual capacity of 2,400,000 long tons, will produce pellets from magnetite concentrate using a new process developed through a joint research program by Midland-Ross, Hanna Mining, and the National Steel Corp. The work that culminated in the decision to construct this plant is the result of a research program for the development of the Midland-Ross heat fast process for the production of prereduced or metallized pellets. PELLETIZING PROCESS There are many acceptable methods for producing oxide pellets from ground iron ores and concentrates, and all of these give an acceptable product for blast furnace utilization. The vertical shaft furnace, the traveling grate, and the grate-kiln have been installed in many pelletizing plants in the northern hemisphere; therefore, the acceptance of these methods and the problems associated with them are well understood. However, this research project investigated a method for improving upon these processes to produce a high quality oxide pellet at a low operating cost.

Jan 9, 1966

By Scott O’Brien, Richard Williams, Camilo I. Mejias, Elias Godoy, Javier Sierra

High-rate thickeners play a critical role in tailings management by enhancing water recovery and increasing solids concentration. However, these units face operational instability due to fluctuations in feed solids, flow rate, and flocculant response typically managed in manual mode with delayed corrective actions. This work presents an adaptive automatic control algorithm designed for dynamic thickening environments. The algorithm integrates real-time measurements of feed density, rake torque, bed level, and turbidity (overflow), optimizing the underflow slurry density while minimizing suspended solids in the overflow. The proposed control strategy is modular, simple, scalable, and applicable to both existing and new thickening systems, offering a robust alternative to manual operation in increasingly demanding metallurgical environments.

Feb 22, 2026

By R. V. Ramani

The overall objective of this study is to contribute to the reduction of the quartz dust hazard in underground coal mines through a better under-standing of the sources and generation of airborne quartz dust. This research project has included extensive experiments in operating mines for (1) documenting the amount of respirable dust generated, (2) measuring the quartz levels in host materials and airborne dust, (3) analyzing the size consist of the mined product, and (4) establishing the relationship between these various parameters. The results of the study indicate that the amount of dust airborne is a very small fraction of the total (<15 µm) and respirable (<7 µm) dust generated. The quartz contents in the total and respirable airborne dust are generally higher than those in the host material. Quartz content increases with decreasing size of airborne dust. Also, it appears that rock breaks into a different size distribution than coal. The source of quartz for the airborne dust appears to be the roof and the floor material rather than the coal seam itself. No general relationship is found between the Hardgrove Grindability Index and either the quartz content in the airborne dust or the amount of respirable dust. Extended descriptions of the experimental design, the experiments, data analyses and results are presented in this volume. The raw data, the data management computer program and the sampling and safety plan are presented in Volume 2.

Jan 1, 1987

By K. Regl, J. Berneder

"AMAG investigated different aspects to improve the resistance against grain coarsening in aerospace alloys during recrystallization and was successful in finding several opportunities to minimize this effect. The studies show that one aspect to counteract grain coarsening is the chemical composition and subsequently all phases that are formed during homogenization. Starting with a fine grain (~ 50 µm) can lead to a final grain size of few mm. On the other hand with a coarse initial grain size (approximately 150 µm) and the right chemical composition the grain size can stay almost constant despite different deformation steps. Additional we investigated different sequences for the component production to eliminate the problem of grain coarsening as a coarse grain has a detrimental effect on product performance.INTRODUCTION In the aircraft industry, aluminium sheets are most commonly deformed in their soft state, followed by solution heat treatment and natural or artificial aging. If the preceding deformation is in a critical amount, during the recrystallization at solution heat treatment grain coarsening can occur. A subsequent deformation to this condition leads to an orange peel surface, which requires additional polishing. Next to this extra effort the coarse grain size produces a drop in the mechanical properties, often below specification limits. If there is no subsequent deformation, this effect is not visible and without destructive testing there is no possibility to detect the error. As mentioned before, this effect occurs during recrystallization, which is a process that is driven by the stored energy in the microstructure. The two most important aspects for an increase of the stored energy are the increase of the grain boundaries fraction (smaller grain size) and the increase of the dislocation density caused by deformation. The increase in dislocation density during the deformation arise from trapping of existing dislocations and from the generation of new dislocations. During recrystallization all grains are built completely new, so all dislocations are removed (Humphreys & Hatherly, 2004). There are three requirements for recrystallization:"

Jan 1, 2018

By G. B. Goodman, W. H. Pailes, P. D. Kaplan, I. Stachura, V. Castronova

"The risk of developing silicosis in underground coal miners, tunnel workers and some foundry workers is well-known. These persons generally develop the classic form of the disease over a prolonged period of time. Workers involved in abrasive blasting of bridges and those polishing tombstones have been reported to develop an acute form of silicosis within a few years of commencing exposure. Not well-appreciated is the potential for development of acute silicosis among drillers at surface coal mines. We report the case of a 33-year--old man who worked primarily at surf ace drilling, developed acute silicosis within three years of beginning exposure, and who initially responded dramatically to corticosteroid therapy. CASE REPORTThe patient is a 33-year-old white man who worked as a rock driller at a quarry and also at surface coal mines in western Pennsylvania since 1975. Prior to 1983, much of his work was done with a wet process in which water was applied to reduce dust generation. After 1983 he worked primarily as a driller at a surface coal mine using a dry process. He never wore a respirator. He described the dust as being so dense that he ""couldn't see anything.- In August 1986, he presented to his local physician with a complaint of pleuritic chest pain and shortness of breath. A chest x-ray film was obtained showing only a few p and q opacities. He continued working and these symptoms subsided, but the patient noted the onset of progressive weight loss. By May 1987, he had lost approximately 50 lb. In addition, he suffered profound malaise, dyspnea, migratory chest pain and arthralgia, fevers and drenching night sweats.A course of erythromycin therapy given in the hospital resulted in only fleeting improvement. Studies for Legionella and Mycoplasma infections were negative, as was a tuberculin skin test. The patient was transferred to Allegheny General Hospital in Pittsburgh on June 4, 1987.There was no history of serious medical illness, including tuber¬culosis. The patient admitted to smoking between I and 1 1/2 packages of cigarettes daily for 2 1/2 years prior to May 1987 when he stopped smoking. He denied intravenous drug abuse, homosexual activity or receiving transfusions of blood or blood products.On physical examination the patient was a thin, febrile white man who appeared chronically ill. Bilateral axillary and cervical lymphadenopathy was present. Chest examination showed restricted expansion and bilateral crackles. Examination of the heart and abdomen disclosed no abnormalities."

Mar 1, 1992

By Bryan Ulrich

Knight Piésold and Co. hosted its annual roundtable discussion on March 17, 2011 at the Stockman Hotel and Casino in Elko, NV. The theme for Roundtable 2011 was, ?High density tailings, paste, and filtered tailings,? although the topic may well have been subtitled, ?Don?t prematurely rule out any technologies before they are given their day in court.? Bryan Ulrich, Knight Piésold?s local representative, as well as Tom Kerr from Knight Piésold?s office in Denver, CO, were on hand to help facilitate the discussion. Ulrich and Kerr are senior vice president and president of Knight Piésold?s U.S. practice, respectively. The event played host to more than 30 attendees from several western states. Attendees included personnel from a dozen mining properties and various corporate offices. There were also attendees from manufacturing and specialist consulting firms who have been providing services to various high-density tailings, paste and filtered tailings operations worldwide. It may be noted that the term ?filtered tailings? is used in this discussion. Alternative terms, such as ?dry stack? or ?dewatered tailings,? should be avoided whenever possible, as such terms tend to give a false sense about the nature of the material since these materials typically still retain a significant amount of moisture.

Jan 1, 2011

By Karl E. Starch

This Bureau of Mines report is a background study of severance taxes on mineral production. The rates, bases, and other features of State severance tax legislation as of March 1978 are presented, as are the amounts of State severance tax collections for fiscal year 1977, Some statistical comparisons between severance tax collections, total State tax collections, and total value of mineral production in the States involved are presented to portray the relative importance of severance taxes both in State tax revenue systems and in mineral industry revenues. A general discussion of the purposes and principles of taxation, the unique nature of a mining enterprise, the various types of taxes imposed on mineral production, and the character and rationale of the severance tax and its impacts on mining firms sets the severance tax in perspective. A bibliography of materials on the severance tax is included.

Jan 1, 1979

By H. Watari

In 1998, a voluntary agreement was reached between the European Commission and the European Car Manufacturers Association (ACEA) to reduce average carbon dioxide emissions of new cars to 25% below 1995 levels by 2008, Agreements have also been reached between the European Commission and the Japanese Automobile Manufacturers Association (JAMA) and the Korean Automobile Manufacturers Association (KAMA), However, the target average of carbon dioxide emissions of less than 140g/km in 2008 is a very challenging goal, Therefore, total product weight reduction is an objective for many manufacturers, This can be achieved utilizing materials possessing high strength and low weight, One material that has recently attracted interest is magnesium alloys, The magnesium alloys are expected to play an important role as next-generation materials, which have possibilities of contributing to lighten the total product weight when magnesium products can be used to replace aluminum and mild steel products.

Jan 1, 2005

By James JV, Petho SZ

The South Deep surface shaft system is being sunk to a final depth of 2750 in below surface and on completion will be the deepest single drop haft in the world. The shafts will intersect the target reef horizon at 2650 to below surface. In order to negate the requirement for a shaft pillar, which would he extremely large at this depth, the reef horizon in the vicinity of the intersection is currently being mined. A high quality crushed waste/classified tailings backfill is being placed in the longwall stoping panels around the shaft intersection area. This kill limit closure and ride which following shaft reef intersection could have a detrimental effect on the long term shaft stability. This paper discusses underground instrumentation results and numerical modelling exercises carried out to confirm that the shaft system will he stable throughout the life of the mine. Instrumentation projects include closure and ride measured between backfill paddocks and haulage leveling exercises carried out to determine the far field rockmass response to mining with stiff backfill.

Jan 1, 1998

By A. L. Worthen

This is one of a series of pacers being published by the United States Bureau of Mines, describing mining and milling methods at crushed-stone plants throughout the United States. These pacers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total production costs. Although the publication of total production cost might not be advisable in some instances, yet a knowledge of operating costs is essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called o this differentiation in order that there will be no misunderstanding of the scope of the cost tabulations. This paper deals with the quarrying and crushing methods used at the Plainville plant of the New Haven Trap Rock Co., which produces annually between 275,000 and 300,000 tons of trap rock, Although pct the largest quarry operated by the company, it typifies the standard methods used by all the quarries in producing crushed stone and has one or two rather unique operating features. The cost of production at this plant is close to the average cost at all quarries of the company.

Jan 1, 1936

By Richard L. Unger

The Crewstation Analysis Programs (CAP) is a package of computer programs that can be used to analyze some human engineering aspects of crewstation design (such as visibility and illumination) that have particular significance in underground mining. It was developed under the U. S. Bureau of Mines (USBM) Health, Safety and Mining Technology program at the Pittsburgh Research Center, Pittsburgh, PA. This manual describes the steps necessary to collect data in the laboratory to develop luminaire profiles for the CAP illumination analysis. It also describes how the CAP Illumination Model calculates illumination. 1.1 How CAP Calculates Illumination 1.1.1 Background -CAP currently includes assessments of visibility and illumination in the surrounding work area. The advantage of using computers for these types of analyses is that many design iterations can be tested quickly and efficiently to learn the effects of changes. This reduces the need for expensive testing using physical mockups. Another advantage is that design ideas can be tested in situations where it would not normally be possible. For instance, the effects of modifications to a lighting system or canopy design on visibility could be tested while the machine remains in service.

Jan 1, 1994

By W. Wan

Diesel particulate matter (DPM) emitted from diesel engines is currently considered to be a health problem in underground mines. As a result, attempts have been made to control DPM both by reducing emission rates and by managing the DPM that gets into the mine atmosphere. This paper presents a method for modeling the generation, transfer and distribution of DPM in the mining sections through the use of a convection-based computer model so that controls for emitted DPM can be evaluated. A variety of ventilation strategies and diesel deployment schemes for room-and-pillar development sections were simulated to compare their effects on average DPM concentrations at several fixed and mobile personnel locations in the section. Input data for the model was gathered from actual diesel development sections and derived from experimental study results provided by other researchers. Studied using the model were ventilation schemes using vent tubing and brattice, exhaust location strategies on the vehicles, and the direction of ventilation at the feeder-breaker location. A summary of results from this study will be presented.

Jan 1, 1994

By M. J. Beus

The Bureau of Mines, under a cooperative agreement with Hecla Mining Co., is conducting a rock mechanics study of the 6,200-ft-deep circu-lar, concrete-lined Silver Shaft in northern Idaho. The objective of the project was to instrument and evaluate lining behavior and rock de-formation when a deep shaft is constructed in a high in situ stress field and anisotropic rock mass. Rock mass displacements were moni-tored with multiple-position borehole extensometers. Liner stress and strain were measured with concrete pressure cells and embedment strain gauges. Field data from the 5,955-ft test level show that rock displacement is controlled by rock mass anisotropy. Liner stress and strain levels reflect the high in situ stress field as well as nearby station and raise construction. Maximum stresses measured in the lining, as a result of shaft excavation, are about one-third of its compressive strength. Subsequent loading pocket excavation resulted in signifi-cantly increased stress and strain levels in the liner. Continued monitoring and preliminary analysis of the data indicate that concrete-lined, circular shafts are stable for the high, unequal horizontal stress fields and rock anisotropy encountered in deep-level mining. Adjacent development work can be expected to significantly alter the initial stress and displacement conditions.

Jan 1, 1984

By L. C. IlsLey

Investigations for safety of electrically operated mine equipment, safety lamps, and gas detectors are made at the Pittsburgh Experiment Station in accordance with published regulations termed "schedules." These schedules are revised from time to time, not only to keep in step with the progress of the industry, but also to permit much freedom of design as possible without lowering standards of safety. The following schedule covering electrical equipment, safety lamps, and gas detectors are now active: Schedule 2D. Explosion-Proof Mine Equipment. Requirements for Approval of of Storage-Battery Locomotives and Power Tucks, Junction Boxes, and Electric Motor-Driven Equipment.

Jan 1, 1939