Search Documents

By G. P. Gu

The in-service 90/10 cupro-nickel tubes in a water-chiller system suffered from severe corrosion damage during their relatively short service life causing unexpected down time. In addition to downtime, the environmental risk associated with losing refrigerant was also a concern that initiated this investigation, Microstructural investigation using SEM and electron microprobe indicated that pitting corrosion had resulted in local nickel depletion, During the corrosion process, copper appeared to have re-deposited around the corrosion pits accelerating the local corrosion.

Jan 1, 2005

By J. D. Marchant

Solid-state electrotransport of impurities in cerium, lanthanum, and praseodymium, using a pulsed current, was investigated. The results were compared with those of using a steady current. Impurities that showed appreciable movement with the pulsed current, but not with the steady current, were as follows: Molybdenum and oxygen in cerium, aluminum, iron, and molybdenum in lanthanum. The use of a pulsed current enhances the practical application of solid-state electrotransport to remove a wider variety of impurities from the host metals.

Jan 1, 1971

By D. S. Fuerstenau, S. Chander

The results of a preliminary investigation undertaken to explore the possibility of treating potential in sulfide mineral flotation systems as an external variable are reported in this note. Two different methods were used to assess floatability. One involved measurement of contact angles at a mineral electrode in reagent solutions, and the other involved direct measurement of flotation recoveries in a Hallimond tube flotation cell that had been modified such that mineral particles were in electrical contact with a gold electrode. Fairly good correlation between the contact angles and flotation recoveries has been obtained.

Jan 1, 1976

By Mehih Demirkan, Kevin Tehansky

Located about an hour drive south from Washington, D.C., the Maryland Transportation Authority (MDTA) contracted with Skanska-Corman-McLean (SCM) to deliver a new Governor Harry W. Nice Memorial/Senator Thomas "Mac" Middleton Bridge, which takes U.S. 301 over the Potomac River, spanning 1.9 mi (3 km) from Maryland to Virginia. The new bridge aimed to improve capacity, safety and access of the roadway and was planned as a four-lane span with deep foundations that would be constructed fewer than 150 ft (45 m) north of the existing alignment of the more than 80-year-old bridge. The new Harry Nice Bridge opened in the fall of 2022 with a design life of more than 100 years, servicing 12 ft (4 m) wide lanes with 2 ft (0.6m) shoulders, doubling capacity, enhancing emergency response, upgrading maintenance and inspection activity access, and featuring lane sharing for cyclists.

Apr 1, 2023

By R. Mishra

The validity of the concept of mine resistance in ventilation systems is examined. Mine resistance is the proportionality constant relating the head generated by a fan and the quantity flowing through it when the fan is connected to a mine circuit. It is the total effect of all branches in the mine ventilation circuit. Its importance lies in the fact that for new mine projections, and in the extensions of existing mines, ventilation calculations are usually based upon adjustments of the mine resistance. In ventilation circuits with regulation, and/or with multi-fans, simple adjustments of the mine resistance curve do not lead to correct solutions. A ventilation system consists of several interconnected subsystems where one subsystem behavior affects that of the others, and the total system. Through a series of simple but realistic examples, the authors will demonstrate the importance of the systems concept in mine ventilation, and its practical application to coal mine ventilation planning.

Jan 1, 1977

By C. Caballero, A. Warczok, K. Itagaki, A. Moyano, J. Font

The Codelco Norte Smelter process 2,500 tpd of arsenic-bearing concentrates with an arsenic content of up to 1.5% in one of its two main smelting units, the Teniente Converter. The product, 1,100 tpd high-grade matte or white metal, is traditionally fed to the PS converters, while the 1,700 tpd of slag is fed to the slag cleaning electric furnace for copper recovery. This is achieved in a very reductive environment which reduces the viscosity of the slag and enhances the sedimentation of the high-grade matte droplets. The behavior of arsenic in this non-oxidative environment was studied at lab-scale and fundamental thermodynamic data were obtained. Based on these data a thermodynamicbase model to assess the arsenic behavior in reductive environment was developed. It is based on a mass balance for the reduction and sedimentation stages performed in an electric furnace which allows the recovery of high-grade matte droplets after decreasing the viscosity of the slag. This model can be a very suitable tool for predicting fractional distribution of arsenic in the slag cleaning electric furnace, when the distribution ratio, vapor saturation degree, temperature, y As and pO2 are given.

Jan 1, 2007

IT is generally accepted that for transport of coal underground from different collecting stations, the system of endless rope haulage with remote control is not only one of the safest and most economIcal, but is also one of the most'efficlent in dealing with output.When the coal measures lie in regular planes, the work of laying down such a haulage presents no difficulties. When, however, the dip of the measures is Irregular, or dislocated by faulting, the management is faced with the problem of constructing vertical curves of such a radius that the sag of the rope will correspond with the road bed, and thus obviate the danger of the rope rising and throwing the skips off the track.The direction of the main roads for haulage purposes being ascertained from the plan of the royalty to be worked, the faults or dislocations in the seam are determined for these roads with the greatest possible accuracy by means of bore holes from the surface.From the data thus obtained the haulage road can generally be so graded that the rope will keep on the floor during haulage operations, although the grades may in places be synclinal.The writer confesses that he knows of no accurate formula for calculating the sag of the rope under varying tensions and so determining the safe radius of the curve, and he had to depend upon past experiences under somewhat sImilar conditions.The accompanying sections illustrate a case where the writer has recently installed an endless rope underground approximately 5000 ft. in length, from the foot of a tunnel in which an endless rope delivers the output to the screening plant, and having to negotiate, first a 400-ft. downthrow fault, and later a 32 ft. upthrow.

Jan 1, 1927

By D. P. Roberts

The stoping of platinum orebodies in the Bushveld has in the past been accomplished by using in-stope pillars to ensure stability of the workings. In the future, the use of continuous mining machines to mine the platinum orebodies is probable. It is not envisaged that such machines will cut in-stope pillars. This paper describes the alternative support systems that will replace the pillars and the stope geometries that will be required for this type of mining. The paper describes how the support resistance provided by in-stope pillars in current mining was determined and then evaluates support systems that can substitute for these pillars. Conceptual layouts based on existing breast mining layouts are presented. The layouts consist of panels of up to 100 m face length between rigid strike stabilizing pillars. A number of design charts are then proposed that allow for the design of appropriate support systems.

Jan 1, 2005

By L. B. Tsymbulov

Sulphide melts formed in the course of smelting of nickel and copper-nickel feed (matte) actually are sulphide-metallic melts since sulphur contained in the melts is in deficiency with respect to metals. The level of metallization is rather relevant feature of sulphide melts and is widely used in calculating material and heat balances for pyrometallurgical processes. Despite of the above parameter? importance, the investigators have no single opinion on what should be understood under metallization level and the method of its determination. In the present study we present the results of our own experimental and theoretical researches that have allowed determination of some mechanisms of sulphide melts? crystallization. Based on the mechanisms revealed new scientifically justified approach has been offered for determining level of metallization of the components present in sulphide melts. It has been demonstrated that sulphur distribution between the melts is substantially different from generally accepted concept.

Jan 1, 2006

By Jan E. Nesset, L. Paul Staples

"High Gradient Magnetic Separation (HGMS) technology, although developed over 2 decades ago, has not been widely applied to the separation of sulphide minerals. Under conditions of strong magnetic field gradients, weakly magnetic minerals such as chalcopyrite (CuFeS2) and marmatite (Zn(Fe)S, sphalerite with iron in solid solution) behave paramagnetically and can be effectively separated from diamagnetic minerals such as galena (PbS). The application of this technology to the separation of Cu-Pb and Zn-Pb bearing streams in the treatment of fine grained complex sulphides may in some cases be more effective than separation by flotation. A 2 TPH Sala HGMS pilot plant was operated at Brunswick for a nine month period, ending in March 1995. The testing demonstrated the mechanical reliability of the technology, the consistency of operating results and the scale up from laboratory testing. HGMS is seen as a complimentary technology to flotation, best suited to performing those separations of galena (and other diamagnetics) which flotation does not do as well.IntroductionBackgroundSince the turn of the century, the magnetic character or magnetic susceptibilities of minerals have been determined with increasing precision and accuracy. Figure 1 illustrates specific magnetic susceptibilities of some common minerals. As long as susceptibility ranges do not overlap, separation is possible.In 1937, the principle of using a magnetizable matrix material in a magnetic field to increase both magnetic flux density gradients and number of capture sites for susceptible minerals was first applied (Frantz). It was not until the 1970's, however, that the genuine development of wet high gradient magnetic separation began with the introduction of very fine matrix materials to the magnetized volume of large solenoid magnets. Today, dozens of HGMS units purify, filter and separate minerals, primarily for the removal of iron stained minerals from clays used in the paper coating and china clay industries and for the recovery of fine titanium and iron oxides in the iron ore industry. Only the Garpenburg mill in Sweden is currently applying a continuous HGMS machine to separate complex sulphide minerals; upgrading a lead concentrate since 1988."

Jan 1, 1996

By E. T. Turkdogan, Klaus Schwerdtfeger, P. Grieveson

The rate of growth of "Fe4N" on a iron was measured by nitriding purified iron strips in flowing am -monia -hydrogen gas mixtures at 504" and 554°C. It is shown that a dense nitride layer is formed when a zone -refined iron is used in the experiments. With less pure iron, the nitride layer is found to be porous. Through theoretical treatment, the self-diffusivity of nitrogen is evaluated porn the parabolic rate constant, and found to be essentially independent of nitrogen actirlity, e.g., D* = 3.2 x l0-12 and 7.9x l0-12 sq cm per sec at 504" and 554?C. Some consideration is given to the mechanism of diffusion in the nitride phase. THERE is a great deal of background knowledge on the solubility and diffusivity of nitrogen in iron, and on the thermodynamics and crystallography of several phases in the Fe-N system. Although case-nitrided steels have many applications in practice, no work seems to have been done on the diffusivity of nitrogen in the iron nitride, ?', phase. The only work reported on the related subject of which the authors are aware is an investigation by Prenosil,1 who measured the growth rate of the e phase on iron by nitriding in ammonia-hydrogen gas mixtures. EXPERIMENTS Purified iron plates of approximate dimensions 1 by 0.5 by 0.03 cm were nitrided in flowing mixtures of ammonia and hydrogen, in a vertical furnace fitted with a gas-tight recrystallized alumina tube. After a specified time of reaction, the sample was cooled to room temperature by withdrawal to the water cooled top of the reaction tube. The furnace temperature was controlled electronically in the usual manner within *l°C; the temperature was measured using a calibrated Pt/Pt-10 pct Rh thermocouple. For each experiment the iron strip sample was cleaned with fine emery cloth and degreased with tri-chloroethylene prior to the experiment. The ammonia-hydrogen gas mixtures were prepared from anhydrous ammonia and purified hydrogen using constant pressure-head capillary flowmeters. The gas mixture flowed upward in the furnace with flow rate of 400 cc per min at stp. The composition of the gas mixture was checked by chemical analysis at regular intervals. In most cases, the compositions of the exit gas and metered input gas agreed within about 0.3 pct, indicating that cracking of ammonia did not pose a problem at the temperatures employed. Two series of experiments were carried out using two different types of purified iron samples. In the first series of experiments at 550°C, vacuum carbon deoxidized "Plastiron" was used. The main impurities present in this iron were, in ppm: 4043, 50-Cr, 20-Zr, 40-Mn, 20-P, 20-S, 20-C, 50-0, and 10-N. In these experiments the rate data were obtained by measuring the change in weight of the iron specimen suspended in the hot zone of the furnace by a platinum wire from a silica spring balance. The nitride layer formed in these experiments was found to be porous, particularly near the outer surface. In other experiments, high purity zone-refined iron (prepared in this laboratory) was used. The total impurity content of this iron was 30 ppm of which 20 ppm was Co + Ni, 4 ppm 0, other metallic impurities were less than 1 ppm. The zone-refined iron bar, -2.5 cm diam, was cold rolled to a thickness of about 0.03 cm and the specimens were prepared for the experiment as described earlier. After the nitriding experiment, the sample was copper plated electro-lytically and mounted in plastic for metallographic polishing. After polishing, the thickness of the ?' layer was measured using a metallographic microscope. The nitride layer formed on the zone-refined iron was essentially free of pores. RESULTS The different morphology of the nitride layers grown on "Plastiron" and zone-refined iron is shown in Fig. 1. Both samples were nitrided side by side for 55 hr. The holes in the less pure iron, Fig. l(a), are confined to a region about one half thickness from the outer surface. The dense layer grown on zone-refined iron, Fig. l(b), is thinner than the porous layer on the "Plastiron". The impurities in the iron are believed to be responsible for the formation of a porous nitride layer. The pore formation may be due to the high nitrogen pressures existing within the nitride layer, e.g., the equilibrium nitrogen pressure is 1.2 x l05 atm in the 38.6 pct NH3-61.4 pct H2 and 6.6 x l03 atm at the Fe-Fe4N interface at 554°C and 0.96 atm. It is possible that the oxide inclusions present in the electrolytic iron may facilitate the nuclea-tion of nitrogen gas bubbles within the nitride layer. Support for this reasoning is the fact that pores are only encountered in the outer range of the layer where nitrogen pressures are largest. The photomicrographs in Fig. 2 show the effect of reaction time on the thickness of the dense nitride layer formed on zone-refined iron. These sections are from samples nitrided in a stream of 29 pct NH3-71 pct H2 mixture at 554°C for 22, 70, and 255 hr. In all the sections examined the nitride-iron interface was noted to be rugged. These irregularities are be-

Jan 1, 1970

By R. L. Roller

In recent years, there have been many articles and papers written on the use of specially designed belt conveyor systems in mining operations, either economic studies or actual experience. These papers generally conclude that the use of these systems can reduce overall costs from 10% to 40% over conventional methods using general purpose equipment (truck/shovel, scrapers, etc.). However, they also generally conclude that conveyor systems are inflexible and capital intensive. With the increasing cost of mobile equipment, the capital cost conclusion is losing steam, particularly when the costs of maintenance shops, road and ramp construction and other related start-up costs are thrown in. Attention here will be focused on answers to flexibility related questions, but first, a look at costs in general. Basic production economics tell us that when we have a small job to do, it is cost effective to use simple, low cost, general purpose tools which will have a minimum impact on total cost. It also tells us that when we have a large project, we can employ methods using special, relatively expensive production tools. Figure 1 illustrates what occurs on projects, of different sizes, with various quantities of production. With small quantities of work, the cost per unit of work starts out much lower using general purpose equipment, rather than using special purpose methods and equipment. However, at a relatively low quantity of work, the cost hits a lower limit and, regardless of how great the quantity of work, the unit cost can never go any lower.

Jan 1, 1985

By B Wu, B W. Lei, B J. Duan

When a coalmine fire occurs, it is crucial to judge the developing trends inside the fire area by analysing the changes of gas concentration in order to formulate the proper rescue measures. At present, few researchers have focused on the relationship between the changing trend of gas product and basic characteristics of fire in the coal fire extinguishing process. To study the relationship of basic characteristics of coalmine fire during the extinguishing process, an experimental platform for coal combustion in a confined space was built, and gas production, flame image and coal temperature during the extinguishing process were monitored and analysed by an online continuous gas analysis instrument, camera and thermocouple. Research shows that during the burning phase of the coal sample in the confined space, the flame zone decreases gradually due to insufficient gas supply. The size of the flame zone fluctuates and shares a positive correlation with CO concentration, while sharing a negative correlation with O2 and CO2 concentrations. Then, in the extinguishing phase, the increasing rate of CO2 concentration and the decreasing rate of O2 concentration both decrease gradually, but CO concentration would rise for a period before it eventually decreases. Coal temperature continues to rise in the open flame stage and does not go down until the flame is extinguished.CITATION:Lei, B W, Wu, B and Duan, B J, 2015. Experimental study on extinguishing characteristics of coal fire in confined space, in Proceedings The Australian Mine Ventilation Conference, pp 279–284 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By Laurence W. Casteel

Indian Creek Mine, newest of the St. Joseph Lead Co. properties, is located in southeast Missouri on the flanks of a buried porphyry ridge. Here the orebodies are very irregular in size and shape and have a regional pitch of about 15°, which may vary locally from 0 to 90°. To maintain an economical grade of ore, selective mining is imperative. The room and casual pillar method is employed with 20-ft diam pillars 35 ft apart where possible. Stopes vary in height from 10 to 55 ft. All are too small to supply a loading unit continuously.

Dec 1, 1956

By Xinghui Meng

The leaching behavior of platinum powder in .iodide solutions under oxygen pressure in an autoclave was investigated. Ammonium salts were added to the leaching solution at neutral pH as a key lixiviant for platinum. The effect of temperature, partial pressure of oxygen, concentration of iodide and of arttmonium salts on the dissolution rate of platinum was examined. Under experimental conditions, the leaching behavior of platinum powder exhibited a complex reaction mechanism. A precipitate was found during the leaching process and was identified to be platinum ammine iodide, Pt(NH3hI4. The dissolution rate was controlled by a series of chemical reactions, the equilibrium concentration of the platinum ammine iodide being responsible for the ultimate limit to the recovery.

Jan 1, 1996

By D. A. Swanson

Predicting when and at what rate seepage will occur from waste-rock facilities is becoming an integral part of permitting and closure at mines situated in dry climates. Such predictions require development of a conceptual framework that accurately describes how water will percolate through a waste-rock facility. Also needed is a detailed hydrological characterization of the waste-rock facility, including measurement of the hydraulic properties of the waste rock and any potential cover materials. This paper presents a conceptual framework describing unsaturated water flow in a waste-rock facility and describes methods for characterizing the hydrology of a waste-rock facility in a dry climate. The methods are designed to collect site-specific data to support accurate and defensible predictions of long-term seepage rates.

Jan 1, 1998

By O. Acaroglu

Selection of the most suitable roadheaders (boom type tunnelling machines) for the galleries/tunnels to be excavated in certain rock and under known project conditions is important for avoiding problems during application. This research utilized a multiple attribute decision-making method and studied how this will be applied for the selection of boom-type excavation machines. The Cayirhan Coal Basin was used for selecting roadheaders using the analytical hierarchy process, which is one of the multiple attribute decision-making methods. To conclude, this study reveals that decision-making methods can be used in the process of selecting roadheaders for the excavation of galleries. Keywords: roadheaders, multiple attribute decision-making, analytical hierarchy process.

Jan 1, 2006

By Lewis T. Wright

It is commonly believed by metallurgists that in copper-smelting, the copper in the slags, which is irreducible by continued " settling," is retained in the form of " prills " of matte. I have frequently held well-settled slag in a molten condition for a long period without being able thereby to reduce the copper-content. The slag acted as though it contained a minimum of dissolved or combined copper that could not be settled out by gravity. I have used reagents, but without satisfying myself in what form this copper existed. The same slags, by fine grinding and elutriation, could not be separated into portions containing more or less copper than the average content. By treating copper-slags in an electric furnace a button of metallic iron and copper was produced, but the high temperature and the strong reducing-action of the furnace mere influences that suggest an explanation of a result not obtainable with ordinary smelting-temperatures. If all the copper in the slag were in the form of copper-matte, and not existing as a dissolved compound with some of the elements of the slag, then the other metals in the matte, such as gold and silver, should occur in the slag in the same ratio to the copper as to the copper in the accompanying matte. This reasoning led me to study the ratio of metals in the products of smelting, and, apart from the issues discussed in this paper, the research has proved both interesting and illuminative. On the assumption of a similar ratio of metals in matte and slag, if the percentage of copper in the slag accompanying a matte containing 50 oz. of silver and 1 oz. of gold per ton of copper was 0.3 per cent., or 96 oz. per toll of slag, there should be found 0.15 oz. of silver and 0.003 oz. of gold per ton of slag; but, in my experience, there is less silver and much

Jan 1, 1910

By H. H. Dievendorff, F. W. Hertel

The method of drilling deep wells into the earth for the recovery of oil and gas is beset with many hazards. This is especially true in the Ventura Avenue field, which has the distinction of being the hardest field in California in which to complete a deep well. The hard, shifting and squeezing formations must be penetrated to great depths in the face of tremendous gas pressures. This field presents problems that keep the operators abreast with all of the latest developments in oil-field tools and machinery and in oil-well drilling practices. Equipment must be strong, and adapted to deep-well drilling and the handling of long heavy strings of casing. High-pressure sands require the utrnost care and attention of the operators and no chances can be taken, since a serious blowout may cause the loss of a well that has cost months of labor and expense. Equipment must meet these requirements or be discarded. Although the deepest wells in the world are not in this field, nor hav:. the longest strings of casing been set, nevertheless, the consistency with which deep wells are drilled and long strings of casing are set places the Ventura Avenue field foremost, in this respect, among the oil fields of the world. The V'entura Avenue field dors claim the deepest commercial oil-producing well in the world, in the Shell Co. of California's "Edison" No. 18. This well was drilled 7015 ft. and came in flowing 3280 bhl. of oil per day. This field also claims the deepest average depth of producing wells in that its Ill producing wells average 5676 ft. in depth. Of these 111 producing wells, 50 arc 6000 ft. or deeper, and 16 are 6500 ft. or deeper. Also, of the 111 producing wells 100 arc flowing, and 11 arc pumping wells. This paper is intended to set forth the methods used in the drilling of deep wells with rotary tools and the handling of long heavy strings of casing in the Ventura Avenue field.

Jan 1, 1928

By J Cahill, M Lee

Leinster Nickel Operations, located in Western Australia, consists of an underground and three open pit mines in relatively adverse ground conditions. This paper reviews our ground control practices in the open pits, covering aspects of ground support, wall control and monitoring. These methods have been effective in allowing mining operations to continue beneath unstable slopes. In particular, the use of Groundprobe?s Slope Stability Radar has enabled the Harmony Open Pit to safely operate for months following indication of failure from traditional methods. This case study highlights the benefits of investing in appropriate slope stability monitoring systems.

Jan 1, 2006