Search Documents

By Arpad E. Torma

The electrochemical behavior of a zinc sulfide concentrate during the microbiological leaching was investigated using ZnS-carbon paste electrodes and a cyclic voltametric technique. The effects of Zn2 [ ] , Fe2+, Fe3+ and Cu2+ on the cathodic and anodic currents associated with zinc sulfide leaching in presence and absence of microorganisms, were assessed. The semiconductor nature of zinc sulfide was discussed in terms of ability of microorganisms to obtain their metabolic energy (through removal of electrons) from this high energy gap substrate. The intermediate electrochemical reactions involved in the ZnS leaching were described.

Jan 1, 1989

By D. D. Harbuck

The U.S. Bureau of Mines investigated germanium and gallium extraction from an ore containing 0.089% Ge and 0.036% Ga. While previous researchers concluded that a reducing agent such as 502 is needed to extract germanium and gallium from such ore, this research showed that high extractions (87% Ge, 97% Ga) were possible using sulfuric acid alone, if the acid concentration were properly controlled. This control was achieved using a two-stage counter-current leach circuit. Microprobe analyses revealed that the non-extracted germanium is in solid solution with quartz, and therefore cannot be leached with 502 or sulfuric acid.

Jan 1, 1991

By Chuck Edwards

Whatever your opinion of the validity of the scientific case for global warming, or of the wisdom of the Kyoto Protocol, it would seem judicious to err on the side of caution and try to sensibly minimize global climate change. To this end, we should take prudent steps to minimize our emission of greenhouse gases. Cameco is the world's leading supplier of uranium for use as fuel in nuclear power plants. Cameco’s uranium production fuels nuclear power plants in 16 countries. Nuclear power plants generate clean electricity without greenhouse gas emissions. This presentation describes the role that uranium and nuclear power can have in meeting the growing demand for electricity and at the same time combating global climate change.

Jan 1, 2004

By Kerry Lahti, Bryan Ulrich

On Feb. 11, 2005, more than 20 mining professionals gathered in Elko, NV for a day-long round-table discussion on heap leaching. Attendees included project managers, operators and environmental professionals. They represented 10 mining organizations. Knight Piésold sponsored the special event. Its seven representatives included three staff members from the company’s Elko Operation, and one each from its Denver, Cajamarca (Peru) and Vancouver offices. The roundtable format was chosen to allow people from the mining industry to share ideas and experiences in an open forum. Rather than presenting prepared talks, spontaneity was encouraged. This resulted in a lively and enjoyable discussion.

Jan 1, 2005

By Robert Linton

AT its meeting on May 21, the Board of Directors approved the recommendations submitted by President Lovejoy and named a nominating committee for the year that is especially well distributed as to major technical interest and as to geography. As may be seen from the list published herewith, two come from the East, two from the Midwest, and three from the far West. Mr. Linton, the chairman, has been a valued member of the Institute for 36 years. A memorandum drawn up by Paul D. Merica, representing the A.I.M.E., and W. R. Barclay, representing The Institute of Metals of Great Britain, setting forth a reciprocal plan for special memberships in each Institute for members of the other, was discussed. Both societies already have formally approved the plan in principle and Dr. Merica was clothed with full authority to agree on a few small details that have not been settled, and conclude the arrangement in behalf of the Institute.

Jan 1, 1936

By R. A. Wharton, Z. Yang, R. W. Smith

The electrokinetic and flotation behavior of the green alga Chlorella vulgaris was studied in the absence and presence of Pb(II), Al(III) and flotation collectors. It was found that the presence of Al(III) is necessary for good flotation of the organism, whether or not Pb(II) is present, when dodecylammonium chloride or sodium dodecylsulfate is used as collector. Best flotation using dodecylamine is at about pH 8, and best flotation when using sodium dodecylsulfate is at about pH 4. It appears because of the small size of the organisms that the Al(III) is necessary for flocculation to enhance bubble-cell contact and C. vulgaris removal from water. When N-dodecyl-2-aminopropionic acid is used as collector, good flotation occurs at about pH 4 without the addition of Al(III).

Jan 1, 1992

By H. Kazemi

An ideal theoretical model of a naturally fractured reservoir with a uniform fracture distribution, motivated by an earlier model by Warren and Root, has been developed. This model consists of a finite circular reservoir with a centrally located well and two distinct porous regions, referred to as matrix and fracture, respectively. The matrix has high storage, but low flow capacity; the fracture has low storage, but high flow capacity. The flow in the entire reservoir is unsteady state. The results of this study are compared with the results of the earlier models, and it has been concluded that major conclusions of Warren and Root are quite substantial. Furthermore, an attempt has been made to study critically other analytical methods reported in the literature. In general, it may be concluded that the analysis of a naturally fractured reservoir from pressure transient data relies considerably on the degree and the type of heterogeneity of the system; the testing procedure and test facilities are sometimes as important. Nevertheless, under favorable conditions, one should be able to calculate in-situ characteristics of the matrix-fracture system, such as pore-volume ratio, over-all capacity of the formation, total storage capacity of the porous matrix, and some measure of matrix permeability. INTRODUCTION The analysis of flow and buildup tests for obtaining in-situ characteristics of oil and gas reservoirs has received considerable attention in the past decade. Most of the available techniques result in reliable conclusions in macroscopically homogeneous reservoirs or in the homogeneous reservoirs with only certain types of induced and/or inherent heterogeneity (such as wellbore damage, etc.). In general, the greater the degree of heterogeneity, the less the reliability of the information deduced from the pressure transient data. A commonly encountered heterogeneous system is a naturally fractured reservoir where two types of distinct porosities occur in the same formation. The region containing finer pores may have high storage and low flow capacities. This is called the matrix. The remaining region may have high flow capacity with low storage. The latter region is generally the set of interconnecting fractures and fissures of the rock, and for this reason it is called the fracture. Ordinarily, we wish to obtain the permeability and porosity of each region and perhaps the frequency of the fracture distribution in a reservoir. Such information is necessary for reservoir engineering. Other information, such as wellbore damage, will be useful in evaluating possible remedial work for such fields. Few authors have suggested theories to aid in calculating the in-situ characteristics of a naturally fractured reservoir similar to what we have described above. Pollardl suggested that a naturally fractured reservoir contained three distinct regions: a damaged or an improved region surrounding the wellbore, and the two remaining regions the same as described earlier. He suggested that the flow was taking place from the tight matrix into the highly conductive fractures, then into the we wllbore region and finally into the well column. He concluded that the average pressure buildup in each of these distinct regions can be expressed approximately in terms of an exponential decay function of time. He also hypothesized that the decay coefficients for each of these functions were significantly different from each other; consequently, each of these functions became dominant in turn, in the process of pressure buildup. Thus, by a proper graphic plot of the logarithm of wellbore pressure differences vs buildup time, each of these functions could be determined (see Fig. 1). Pollard suggested methods of determining the wellbore damage and fracture volume. Later Pirson and Pirson2 extended

Jan 1, 1970

By P. E. Nielsen, T. L. Loga, B. B. Mauko

A numerical model is presented which simulates the dynamic fracturing process for a circular geometry fracture in a uniform stress medium. The dependence of crack aperture and net pressure in the crack upon various dominant parameters of the fracturing process is discussed. An analysis of a 75% nitrogen foam fracture in a coal seam at 5600 feet (1707 m) is also presented. The analysis is based upon the discussed parametric trends, the job records of treatment parameters, and a Nolte plot of net downhole pressure. It is interpreted that fracturing with water, in pre-foam fracture pump tests, resulted in significant fracture height growth. However, the subsequent foam fracture had reduced height growth due to the high effective viscosity of the foam and due to the higher magnitudes of elastic modulus and stress in the bounding rock strata with respect to the coal.

Jan 1, 1986

By John M. Karpinski, David S. Cahn

A new device based on a constant rate of loading has been developed for the compression testing of green and dry pellets. This device has a lower test variation for green pellets than the existing constant deformation rate tester. While the test variations for dry pellets are similar for both types of machine, the new tester is sensitive enough to measure dry pellet deformations of 15 µ in. for cyclic loading studies. In the study discussed here, the compressive load at which a pellet breaks proved to be a normally distributed random variable, and the load-deformation relationship was found to be linear for dry pellets but not for green pellets. The paper emphasizes the need for a standardized test procedure throughout the industry. For many years the green and dry compressive strengths of pellets have been considered as possible criteria of pellet performance during induration. Little attention, however, has been given to standardizing the unfired pellet compressive strength test or to determining the characteristics of this test. The purpose of this study was to compare the constant deformation rate test with constant loading rate

Jan 1, 1969

By Ibrahim Yusufoglu, Cem Kahruman, Mert Zoraga

In this study, a strontium sulfate mineral (celestite) was converted to strontium oxalate in solutions containing ammonium oxalate as a reactant. The experiments were carried out under isothermal conditions. The effects of stirring speed, ammonium oxalate concentration, particle size and temperature on the conversion rate were investigated. During the conversion process, definite volumes of solutions were taken from the reactor after different reaction times for the determination of sulfate ions using ICPOES. Fractional conversions of strontium sulfate were determined at different times and fractional conversion vs time diagrams were generated. It was found that the conversion of strontium sulfate was increased by increasing the ammonium oxalate concentration and temperature in addition to decreasing the particle size. The effect of stirring speed was negligible on the reaction rate. It was observed that above 328 K, a protective layer of strontium oxalate was formed on the strontium sulfate particles. X-ray Powder Diffraction technique was used for characterization of solid substances.

Jan 1, 2014

By J. M. W. Mackenzie

Three major developments have dominated the recovery of gold from ores, viz; 1846 Elsner's studies of gold solubility in aerated alkaline cyanide solutions 1887 MacArthur and Forrest's process based on zinc precipitation 1980+ Large scale development of the CIP process The brevity of this list for a metal whose extractive metallurgy has been as widely studied as any metal reflects the fact that the chemistry of the gold recovery process, as opposed to the engineering has seen few significant breakthroughs in over a century of application. to The purpose of this paper is introduce a new chemistry for gold recovery which may, in the future, add significantly to the technology of gold recovery. This new chemistry is based guanidine functionality - (R2R2N) 2 C = N R2 on the In developing the use of the guanidine functionality for the recovery of gold as the aurocyanide anion from leach solutions and pulps, Henkel has, as its objective, the development of an effective gold selective ion exchange resin. As will be seen, the initial investigation of the properties of the guanidine functionality in the solvent form for gold recovery lead to some significant metallurgical developments of their own but, the foremost objective was, and remains, the development of a resin for gold recovery. As a part of this development project, Henkel has entered into association with Mintek, South Africa, and this ongoing association has the potential to develop RIP/RIS technology for the gold industry. More details on Henkel's gold recovery technology and Mintek's role in this programme are given in (1). an The application of ion exchange resins to gold recovery is not new and many reviews have been published on the advantages of this process, and on the current state of the art of gold recovery by ion exchange resins. (2)(3)(4) Widespread application of ion exchange resin based processes for gold recovery has, however, not occurred to date. Fleming and Cromberge (5), described some significant pilot plant RIP trials in South Africa and the partial success of these pilot plant trials held out the tantalising possibility of a breakthrough in gold recovery based on RIP technology. Despite this pioneering work, only two really significant applications of RIP technology for gold recovery exist today. These are the Golden Jubilee Plant in the Eastern Transvaal South Africa and the widespread, although in some respects technically backward, use of ion exchange for gold recovery in the former USSR. There are two main reasons for the current scarcity of RIP and RIS plants used for gold recovery. These are: 1. 2. The perceived problems of engineering RIP plants The lack of a resin having suitable chemistry for both gold loading and gold elution The problems of engineering RIP plants have been largely overcome in the last 25 years. Much of the development in RIP plant design took place in the uranium industry during the rapid expansion of that industry in the mid 1970's. In addition, the development of CIP engineering systems has lead to the development of in-pulp solid extractant based metallurgical plant designs which can, with limited modification, be adopted to RIP. The lack of a resin having suitable chemical properties has almost certainly been the main reason for RIP/RIS not being introduced into the gold industry over the past decade. Attempts to use RIP/RIS have focussed on either conventional we ak base or conventional strong base resins. The weak. base resins have the disadvantage that they

Jan 1, 1993

By Robin J. Batterham

The Bologna Process started in 1999 with a declaration signed by ministers from most European countries. As of 2012, the Bologna Process now has 47 participating countries (EHEA 2012). Overall, the Bologna process has demonstrably changed higher education in many countries to allow for considerably more flexibility in course offerings. Keywords: bologna model, education

Sep 1, 2012

By Arnfinn F. Prugger, Fritz F. Prugger

"The Saskatchewan potash beds are overlain by a number of water-bearing formations. There are water zones in the footwall as well. These aquifers created difficulties during the construction of shafts to the potash beds at 1()(}() m depth, and they pose a continuous threat to the safe and efficient operation of potash mines in the province.The first shafts to be sunk in Saskatchewan encountered major problems during shaft sinking. Of the 17 potash shafts started in the province, five had major water inflows during shaft sinking or after production startup, and one was abandoned because of water problems. The biggest obstacle encountered during shaft sinking was a poorly consolidated sand-shale-clay-siltstone unit commonly called the Blairmore Formation, which occurs at a depth of about 500 m. The initial problems with shaft sinking were overcome in the 19605by using European methods of freezing and the installation of cast-iron tubbings or a double-steel lining through water bearing horizons.From the start of production in the early 19605, operators have been aware of the ever-present hazard of potential water inflows into mine openings from permeable units in both the hanging wall (carbonates of the Dawson Bay Formation which occur 15 m to 50 m above the mining level) and the footwall (carbonates of the Winnipegosis Formation which occur 50 m to 150m below). This awareness has been reflected in conservative over-all extraction rates and mining layouts specific to local conditions. In spite of this consciousness, a number of water problems have occurred in operating mines. These have resulted in everything from simple increases in expenditure to the shut-down of one mine in 1987.In this paper a history of water problems in the Saskatchewan potash industry is given, followed by a summary of measures that are now commonly used to avoid these problems. A description of each inflow event is given, and the attempt is made to analyze the causes of each occurrence. Based on what was learned f rom each event, suggestions are made to prevent future water inflows into potash mines."

Jan 1, 1991

By Guojun Qi

This work relates to wafer bumping technologies for flip chip packaging applications in the electronics industry. Nickel and its alloys are alternative under bump metallization (UBM) materials because of their slower reaction rates with Sn-based solder as compared to Cu-based UBMs. In this study, we compared the morphologies of the intermetallic compounds (IMC) formed between Sn-bearing solders (Sn3.5Ag and eutectie Sn-Pb) and two types of nickel- based UBMs, electro less Ni-P (EN) and sputtered nickel. Both chunky-type and needle-type of intermetallics were observed between the EN UBM and the solders. In the case 'of sputtered Ni UBM, there is only a layer of scallop-type intermetallics formed, The morphology change and growth kinetics of the IMC in thermal aging process were analysed. Kirkendall voids were noticed from samples ofSn3.5Ag solder vs Ni-P UBM that have undergone prolonged thermal aging at high temperature.

Jan 1, 2003

By John Wright

During June and July 1999 a United States Antarctic Program (USAP) team of three commercial divers and one blaster successMy removed an underwater rock obstruction which interfered with safe docking practices of research vessels that call at Palmer Station - the USAP research facility located on Anvers Island, Palmer Peninsula Area, Antarctica. Ordinarily, such a project might be considered routine. However, certain aspects of the project, particularly those dealing with logistics in a remote corner of the earth, sat3eguards for marine biota, and working underwater in the dark of the austral winter, conspired to make this project interesting. Even more challenging was ensuring the protection of the existing pier - a deeply corroded sheet pile structure backfilled with loose gravel and rock - which lay less than 50 feet away from the target obstruction, not to mention uncertainties at the outset as to the nature of the rock mass forming that obstruction.

Jan 1, 2001

By Dale S. Preece, Matthew A. Reisenmay, Avione Northcutt

The ability to simulate the explosive effects of land mines on military vehicles is a valuable capability in the defense community. The current competency levels of such simulations, however, are in need of improvement. Experiments have been conducted to measure the explosive induced impulse of a land mine on a steel plate placed above the explosive charge. The purpose of this paper is to report the findings of a variety of simulation tests conducted in order to correctly predict the empirical impulse data gathered in corresponding experiments. The computer hydrocode, AUTODYN v5.0.01 (Century Dynamics, 2003), is the simulation code used to simulate, and process the results. The experimental data has not been made available to allow computer analysts to exercise their codes on the problem without the temptation to tweak parameters in order to match computer code predictions with experimental results

Jan 1, 2005

By R. Poulin, R. Pakalnis, D. Peterson

Introduction A comprehensive project has been completed at the University of British Columbia that focused on the development of a commercially competitive composite cable bolt. Laboratory evaluation consisted of pull tests, preliminary shear tests, grout column testing and scanning electron microscope evaluation of the composite cable bolt. Field implementation at five underground mines throughout Canada were completed for technical and overall performance evaluation of the new product. The project began in 1989 under the sponsorship of HDRK Ltd., a consortium of mining companies including Inco, Noranda and Falconbridge Ltd. The objective was to develop a cuttable cable bolt that would serve as support for a continuous miner within a hardrock environment (Mah, 1994). The bolt was required to be cuttable by a continuous roadheader without adverse effects to equipment, personnel and the milling process. From the beginning, the focus was to employ existing cable bolt installation technology (Goris et al., 1994) whereby the cable bolts are grouted within a 4.8-cm-diam (1.08-in.diam) or larger employing a portland cement grout having a water: cement ratio between 0.35:1 to 0.4:1. The prototype, developed from Phase I, was technically comparable to that of conventional steel cable bolts. However, high cost and limited accessibility hindered its commercial acceptance. The second phase of the project was sponsored by the British Columbia Science Council and Pacific Pultrusions Ltd. of British Columbia to locally develop a glass fiber cable bolt. This phase of the project has resulted in the DAPPAM cable bolt (Pakalnis et al., 1994). DAPPAM Cable bolts are the second most used support method in Canadian underground mines after mechanical rock bolts. It is projected that 870,000 m (2.9 million ft) of cable bolts are installed annually in Canada (Poulin et al, 1994). The objective of the research program was to develop a glass fiber cable bolt with similar pullout strengths to the conventional steel cable bolts (267 kN - 60,000 lbf). More than 200 laboratory pull tests were conducted employing standard cable bolt test procedures, as outlined by the US Bureau of Mines (Goris, 1994), to assess optimum rod and surface composition, geometry, number required, pullout and shear characteristics, among others. This resulted in the DAPPAM cable bolt (Fig. 1). It consists of 10 individual 0.6cm-diam (0.25-in.-diam) rods enveloping a 2.2-cm (0.8-in.) outside diameter, high-density polyvinyl grout tube. The composite used in the construction of the rods is comprised of about 65% glass fiber within a 35% polyester resin matrix (by volume). Through pultrusion (a continuous fabrication technique), the fibers and resin are combined into a composite material. The strength of the overall composite is largely governed by the material properties, the alignment [ ] of the fibers relative to the applied load and the density and interaction of the overall components within the composite. A further modification to the composite was the addition of a sand grit to the surface of the individual rod. This increased the overall bond strength between the rod and the cement-based grout, used to solidify the cable bolt to the rock mass. The grout tube has an inside diameter of 1.9 cm (0.75 in.) and is rated at a pressure of 1.72 MPa (250 psi). During installation, the grout is pumped through the annulus of the grout tube thereby filling the hole from toe to collar. Laboratory and field trials concluded that a minimum drill hole diameter of 4.8 cm (1.08 in.) be used to ensure optimum grout coverage. Table 1 compares the design strengths (as tested) for DAPPAM vs. the ultimate strengths for a conventional 1.6cm (0.6-in.) steel cable bolt. The characteristics for the steel cable have been derived directly or indirectly by Goris et al. (1994). A design tensile strength of 289 kN (65,000 lbf) was proposed for the composite developed. However, recent tests have indicated maximum breaking strengths of more than 400 kN (90,000 lbf) (Fig. 2). Figure 2 shows the load vs. displacement pull out curves for steel and DAPPAM cable bolts. The methods of testing were standardized so as to be able to compare the results directly. The shear strength of the fiberglass cable is largely a function of the surface area sheared. Shear strengths of 89 kN (20,045 lbf) were obtained for the configuration shown in Fig. 1 when sheared normal to the axis of the cable. The testing procedure was similar to the shear tests performed on steel by Goris (1993). It is important to reinforce the implication that critical bond strength has on the success of an overall support system.

Jan 1, 1995

By U. F. Kocks

SINGLE slip and a single parallel array of edge dislocations have been obtained in silicon single crystals by homogeneously bending them in a four-point dead-loading device at 1000°C around the [211] axis with [253.] as the tensile axis which encloses an angle of 40° with the glide plane. Other orientations or lower temperatures proved unsuitable. The homogeneity of the bending was checked by the method shown in Fig. 1. The chemically polished specimen was exposed to parallel light from a microscope-stage lamp. The sharpness of the focus of the reflected light is an approximate measure of the circularity of the sample. This method permitted the determination of the actual radius of bent specimens within 10 pct accuracy. The etching solution developed to show up dislocations consisted of the following volume parts: 2 HF, 1 HNO,, 2 CH,COOH, 1 a solution of 5 wt pct of CuNO, in water (Rosi'). The acetic-acid content was adjusted to produce fine well-defined etch-pits in about 2 min at room temperature. The effectiveness of the etch did not depend on the crystal-lographic orientation of the face etched. The number of etch pits produced after a given deformation was checked in the usual way against the Cahn formula' and showed good agreement. As it is to be expected from the orientation of the primary system there are slip steps on the top and bottom faces but not on the side faces (perpendicular to the bending axis), whereas etch pits appear on the side faces but not on the top and bottom faces. This is different only for occasional dislocations of a secondary glide system. All the micrographs included have been taken in places where the most of secondary glide could be seen. From this it is evident that in the homegeneously deformed region the number of secondary dislocations was less than 1 in 1000 of the primary type. Dislocation Distribution—A series of tests with varying amounts of deformation is shown in Figs. 2(a-c). An observation that can readily be made from these pictures is that the linear density of dislocations within slip lines is relatively constant and independent of the amount of deformation. "Slip line" in this context is understood to mean a line that is a straight connection of individual etch pits. The heavily pitted bands which can be seen in each of these three pictures may be resolved fairly definitely, at higher magnifications, into many "slip lines" the distance between them being of the order of 0.5p The distance between dislocations in slip lines is of the order of 2p and it is also fairly constant in going from the neutral zone outward. The higher over-all dislocation density in the outer regions of any sample and the higher total number in a more heavily deformed sample, are effected by a larger number of "slip lines." The relative constancy of the dislocation distance within an individual slip line is surprising. The absence of pile-ups" may imply, if there is no rear- rangement on unloading," that there are no substantial obstacles to slip in this case. It seems that the equilibrium distribution of the dislocations in each active slip plane under the higher external stress on

Jan 1, 1959

By K Palmer, G J. Artmont

Alluvial gold is an ideal exploration tracer to bedrock source and indicator of bedrock mineralisation style because: (i) gold occurs in a wide range of deposit types, (ii) primary composition is sensitive to style of mineralisation, and (iii) it is a heavy resistate mineral that is readily preserved and easily sampled. In regional exploration of the Central Ranges of Irian Jaya, alluvial gold mineralogy has been applied to maximise the information return from panned concentrate sampling and to focus exploration effort. Primary gold is a solid solution of Au+Ag¦Cu¦Hg, ¦ trace Pd, Te, and Sb. In general Ag¦Hg increase and Cu decreases with inferred decreasing temperature of formation, and gold from particular mineralisation styles has signature compositions that can be used as indicators of bedrock mineralisation type. Furthermore, the abundance of alluvial gold is an indicator of the economic potential of a catchment. The convergent continental-oceanic plate geology of the Central Ranges is conducive to a wide range of mineralisation styles. Mineralogy of gold in ophiolite, skarn, porphyry, mesothermal vein and possible VHMS environments is characterised from alluvial and bedrock samples, and the use of gold mineralogy in prospecting at regional scale through prospect definition to drilling is demonstrated.

Jan 1, 1995

By John R. Reynolds

This paper describes mining and milling methods of the American Smelting & Refining Co. at the Morning mine in the Mullan area of the Coeur d'Alene mining region in Idaho and is one of a series of Bureau of Mines reports dealing with methods and costs of mining throughout the United States. The Morning mine has been described previously in a Bureau of Mines report published in 1930,2/ and the milling methods and costs at the Morning concentrator were presented in a Bureau of Mines report published in 1932. 3/ These reports are supplemented by this publication, which presents data to show the effect of changing times and conditions on a typical medium-size mining operation during the latter part of its history, when costs were rising and production was from increasingly greater depths. The report contrasts two periods in the history of the mine-periods not too far separated in years but considerably different in economic conditions. During the first period (1939) costs of labor and materials were moderate, mining operations were just being transferred from the main shaft to deeper workings opened from the offset shaft, and the operation prospered. During the second period (12 years later) production costs had increased following the national trend in all industry, mining was from greater depths near the bottom of the ore body, and the operation was becoming unprofitable. Mining on the lower levels of the property ceased in 1953.

Jan 1, 1956