Search Documents

By Rick Honaker

Rare earth elements (REEs) contained in coal and associated mineral matter exist in several forms including micro-dispersed minerals, ion adsorption onto clay surfaces, and chemically bound. Tests found that REEs can be effectively recovered from certain components of three coal sources by leaching under mild conditions followed by solvent extraction. A range of pH values were evaluated at solution temperatures of 25 and 75 °C. When using 1.2 M of sulfuric acid, nearly 85% recovery of the REEs was extracted from the middlings material collected from an operating plant. Acid leaching of a second middling source from another plant resulted in 60% of the total REEs being recovered under the same leaching conditions. Solvent extraction treatment of the leachate produced from six different coal sources resulted in products containing up to 50% total REEs from feedstocks starting with around 300 ppm.

By Tulu B. Ihsan, Mark A. Van Dyke, Ted M. Klemetti

"How well do current modeling procedures calculate the rear abutment extent and loading? Does an improved understanding of the rear abutment extent warrant a change in standing support in bleeder entries? What is the optimal standing support for bleeder entries separated from the longwall startup room by a barrier pillar? To help answer these questions and to determine the current utilization of standing support in bleeder entries, four bleeder entries at varying distances from the startup room were instrumented, observed, and numerically modeled. This evaluation was intended to determine the rear abutment extent and magnitude at various locations to optimize standing support in these entries and those under similar conditions. This paper details observations made by NIOSH researchers in the bleeder entries of a deep cover longwall panel; specifically data collected from instrumented pumpable cribs, observations of the conditions of the entries, and numerical modeling of the bleeder entries during longwall extraction. The primary focus was on the extent and magnitude of the abutment loading experienced by the standing support. As expected, the instrumentation of the standing supports showed very little loading relative to the capacity of the standing supports—less than 25 tons load and 1 inch convergence. The observations of the conditions showed little to no change from before the longwall panel extraction began to when the panel was more than 50% extracted. In addition to the observation and instrumentation, numerical modeling was performed to evaluate the bleeder design. The Flac3D program was used to evaluate these four bleeder entries using previously defined modeling and input parameter estimation procedures. The results indicated only a minor increase in load during the extraction of the longwall panel. The model showed a much greater increase in stress due to the development of the gateroad and bleeder entries, with about 80% of the increase associated with development and 20% with longwall extraction. The Flac3D model showed very good correlation between expected gateroad loading during panel extraction and those expected based on previous studies. The front and side abutment extent modeled was very similar to observations from this and previous panels with similar conditions. The results of this study showed that the rear abutment stress experienced by this bleeder entry design was minimal. The convergence measured in these bleeder entries was small enough not to mandate any additional support beyond development even by U.S. or Australian standards. The pumpable crib load and convergence experienced depends on the geological setting, mining geometries, and timing. The farther away from the startup room, the lower the applied load and smaller the convergence in the entry if all else is held constant. Finally, the numerical modeling method used in this study was capable of replicating the expected and measured results near seam."

Jan 1, 2017

By Elmer H. Citron

The Monterey Coal Company, a wholly owned subsidiary of The Carter Oil Company of Houston, Texas, recently awarded a contract to build the Monterey No. 1 Preparation Plant, which will be located near Carlinville, Illinois, to the McNally Pittsburg Manufacturing Corporation. The preparation plant will be one of the most modern jig preparation plants in the State of Illinois. Illinois No. 6 coal will be delivered by a 48" slope belt having 35-degree carrying idlers, operating at 650 FPM and operating on an incline of nearly 17 degrees. The slope belt is driven by two 450 BP motors and will deliver the mined coal at the rate of 1800 TPH to a stationary step-type ' screen having six-inch openings. The overproduct from the stationary screen will discharge into a 10' x 24' McNally Rotary Breaker and the underproduct will bypass the rotary breaker. The rotary breaker is equipped with heavy manganese screens with 6 ½" diameter openings. The sized 6" x 0 coal from the stationary step screen and the rotary breaker will be discharged by gravity to a 4%" raw coal incline storage belt. The 48" raw coal storage belt will deliver the 6" x 0 sized coal at the rate of 1800 T?H to an 8000 ton concrete raw coal silo, 70 feet in diameter and 1x7 feet high. The 6" x 0 sized coal will be drawn from the concrete storage silo by seven (7) 36" wide reciprocating plate feeders. Five feeders are to have constant speed drives at a rated capacity of 145 TPH each. Two (2) feeders will have remote con- trolled variable speed drives, to provide a varying feed.

Jan 1, 1970

By R. S. Handy

This paper describing the milling practices at tae concentrators of the Bunker Hill and Sullivan Mining and Concentrating Co. is one of a series being prepared by the United States Bureau of Mines on milling methods and costs in the United States. The possibility of useful comparisons has prompted the description of all five of the mills operated by the Bunker Hill and Sullivan Company in northern Idaho. The general features of these mills are tabulated below: [ ]

Jan 1, 1930

By W. Drummond

The cooling of smelter gases by air dilution, adiabatic evaporative cooling and indirect heat exchange is discussed with reference to the ,process, to the subsequent cleaning of the gas and to the use of the heat extracted from the gas. The method of reducing the effect of acidic ,sulphide formation on the corrosive properties of the gas and the dust and the development of surface cleaning mechanisms are discussed. The development of indirect recuperators using air, water or steam cooling, made 'possible by the control of surface fouling is traced. The application of the modern Waste Heat Boiler to the new sulphide smelting processes is discussed with respect to the natural and forced circulation concepts. Case histories are presented to illustrate mistakes made with respect to designs produced without recourse to sensitivity analysis and without an appreciation of "worst process conditions".

Jan 1, 1992

By Z. Yang, M. J. Collins, N. E. Tuffrey, R. J. Kalanchey, I. M. Masters

The high elevation of China Western Mining Company (WMC)' s Ganhe refinery, and the high iron content of concentrates produced by the WMC mines, were key factors in the selection of pressure leaching by WMC for their new zinc refinery. This paper describes the results of pressure leaching test work conducted by Sherritt in Fort Saskatchewan with a sample of WMC concentrate from Qinghai Province in China. Results from batch pressure leach tests and a four-day pilot plant campaign are reported. The pilot plant campaign included continuous operation of a two-stage pressure leach circuit, as well as neutralization and iron removal steps, resulting in the production of iron-free zinc sulphate solution. Greater than 98% zinc extraction was achieved in pressure leaching, while producing solution containing about 9 g/L H2SO4 and 2 g/L Fe. Following neutralization and iron removal, the solution contained about 170 g/L Zn and less than 10 mg/L Fe. Overall recovery of sulphur in the zinc concentrate feed to elemental sulphur byproduct was about 85%, while 75 to 80% of the indium in the feed was recoverable from the neutralization residue. The test results highlighted the technical and economic advantages offered by the Sherritt Zinc Pressure Leach Process and provided the required data for the engineering design.

Jan 1, 2008

By D. W. Hendrickson

Cliffs views the process as extending from mine planning to cargo loading including auxiliary systems such as material handling and plant utilities. Process automation is recognized as an area that can provide significant improvement opportunities with less capital requirement than major flowsheet modifications. This paper discusses the development and results of a strategy to allow and promote implementation of process automation improvements at individual mines based on their economic priorities taking advantage of common systems and concepts for use at multiple mines where practical. Specific process control upgrade projects a Hibbing Taconite Company and the Empire Mine are reviewed in detail.

Jan 1, 1998

By A. Simon, J. Weyer, J. Brune, V. Zhiteneva

"Reiche Zeche is a lead-zinc-silver deposit in Freiberg, Germany, that was mined for over 800 years. Since 1969, Reiche Zeche has been a teaching and research mine with numerous adits for dewatering large amounts of inflowing water. Infrequent metal water quality monitoring in the 1980-1990s and flooding of the mine in 2002 led to a lack of relevant data. New measurements were taken at different level adits and ore veins for comparison to historical values, revealing pH levels as low as 1.95, conductivity as high as 22000 µS/cm, and an overall trend towards less acidic waters. INTRODUCTION Reiche Zeche is part of the Himmelfahrt Fundgrube, a former iron ore mine in Freiberg, Germany, in the Erzgebirge mining region of Saxony. The polymetallic sulfide ore found in Freiberg was mined from 1168 to 1969, and though it is no longer producing ore, Reiche Zeche remains as a teaching and research mine for the Technische Universität Bergakademie Freiberg. The most important ore minerals mined were sphalerite, galena, pyrite, chalcopyrite, and silver, and important gangue minerals include calcite, fluorite, barite, siderite, and quartz (Zänker et al 2002). Over one thousand ore loads were mined from this region during operation, which was ceased in 1969 after the lower part of the 700 meter depth was flooded, leaving only the top 200 meters under the surface open for research and teaching. Mined materials from this region can be separated into high grade ore and waste rock. High grade ore, composed of pyrite, sphalerite, galena, chalcopyrite, and arsenopyrite, was brought to surface for smelting during mine operation, and spaces were backfilled with waste rock, which is the primary site of sulfide oxidation and acid mine drainage (Haubrich and Tichomirowa 2002). The waste rock includes remnants of ore from ore loss, veins which were too small to mine, or ore minerals within host rock. Waste rock is primarily composed of biotite gneiss, with sulfides including jarosite, gypsum, minor anglesite, scorodite, and sulfur (Haubrich and Tichomirowa 2002). When weathered, the gneiss forms clay minerals such as illite and kaolinite (Haubrich and Tichomirowa 2002)."

Jan 1, 2016

By D. F. Malan, U. Du Preez, P. S. Heyns

South Africa has two main platinum reef deposits, namely the Merensky reef and the UG2 reef. These reefs are currently mined using traditional drilling and blasting methods. Mechanized cutting could potentially enable continuous mining, which would offer significant advantages. This would require thorough understanding of the cutability of the rock. To explore this, a linear cutting machine was developed to conduct laboratory scale cutting tests. This work describes the development and commissioning of the cutting machine using sandstone, as well as subsequent characterization tests on UG2 reef samples. UG2 reef has large variability in strength on a millimeter scale. This introduces uncertainty in the test results due to added variance from one cut to the next for the same UG2 reef sample. Another problem is the variability in rock properties of the UG2 reef, when testing samples from different mines. The cutting tests led to fine fragmentation, which is known to be a significant problem for cleaning operations in underground stopes and warrants further research. A finite element method simulation of the rock cutting was conducted using ANSYS LS-DYNA and the continuous surface cap model to simulate rock cutting in the UG2 reef. It was found that it is possible to use LS-DYNA with the continuous surface cap model to model rock cutting of UG2 reef and get acceptable results, but the user must calibrate the model parameters using the experimental results. Therefore, the model is only fit for one set of cutting parameters and further work is required to generalize results.

Nov 27, 2024

By Walter Miller

DURING the second year of America's active participation in the war the main objectives of the petroleum refining industry were again to provide the four most important product needs for war: 100-octane aviation gasoline, toluene for TNT production, high-quality lubricating oils for the needs of aviation and the armed forces, and petroleum chemicals for synthetic rubber manufacture. All other materials supplied by the petroleum industry took an inferior priority ranking, depending on the degree of essentiality. To accomplish the above objectives the industry initiated and carried on a building program during 1942 and 1943 which will put those two years down in petroleum refining history as the greatest construction years of all time, a record which will hold for decades to come. Led by an estimated total of $900,000,000 going into 100octane and contributory plant investment, it is easy to picture a total of two billion dollars and more going into additional refining-industry plant investment during 1942 and 1943, most of it privately paid for, but a substantial part covered by R.F.C. Government money financing.

Jan 1, 1944

By Jakub Szary

Excavation and shoring adjacent to the above-grade Gilmore train station and elevated guideway was undertaken in 2019. A perimeter secant pile cut-off wall was constructed to a depth 37 m (121 ft) below ground surface consisting of 1.0 m (3.3 ft) diameter drilled piles spaced 750 mm (2.5 ft) on-center, tied back with soil anchors, and reinforced with W610 steel sections every 4th pile. A bracing/jacking system was also constructed to support 3 free-standing guideway caissons within the excavation. An automated instrumentation program was installed to monitor movements of shoring walls and train infrastructure in real time and consisted of a robotic total station, inclinometers, tiltmeters, strain gauges, extensometers, and anchor load cells. Baseline monitoring was able to establish diurnal and seasonal movements within the structure, strongly correlated with temperature. The system actively monitored various shoring elements and train infrastructure in real time and alerted the project team when values exceeded predetermined threshold values. Remote reconfiguration of the automated system allowed for more frequent monitoring during jacking of Pier 29 in March 2022. Monitoring data was in agreeance with on-site manual surveying results and jacking dial gauges, and proved to be a reliable monitoring system for construction applications.

Sep 1, 2022

By Kristen R. Bingham

"Today, more than ever, drilling and blasting contractors are challenged to manage the ever-changing risks associated with blasting operations. New neighborhoods are encroaching upon mine sites and blasting projects are confronted with increasing scrutiny by permit issuing authorities and nearby residents disgruntled by new construction. The act of transporting explosives material to and from thejobsite is far from easy and trouble-free. At the same time, the pressure to stay in compliance with the growing number of government regulations continues to mount. While new tools and technology are appearing in the workplace to address some of these challenges, losses still occur. Can the datagenerated by this technology help drilling and blasting contractors make better decisions? While basic risk management principles are still applicable, do new tools and technology assist in the effort to prevent losses? What are the downsides? In this age of new technology, is face-to-face interaction still necessary? While technology is certainly a useful component in the drilling and blasting world, can it be helpful in defending claims?"

Jan 1, 2017

By William G. Pariseau

Elastic-plastic finite-element simulation of cut-and-fill stoping in deep, narrow veins shows substantial quantitative agreement with field measurements of stope closure and fill pressure made at two mines in the Coeur d'Alene mining district of northern Idaho. The simulation procedure, validated by field data, was used in an analytical study of vein-wall closure and sill-pillar stress as influenced by fill modulus, rock modulus, and premining stress. Ratios of closure and pillar stress in the filled stopes to closure and pillar stress in the unfilled stopes are used as prediction indices for fill performance. In general, the support capability of fill increases dramatically as the ratio of fill modulus to rock modulus approaches 1. A significant reduction in closure .from the open stope--up to 75 percent--occurs with a relatively low-quality 10-ksi-modulus fill (rock modulus of 1,000 ksi). However, a higher quality fill is needed to achieve a substantial reduction in pillar stress from that of the open stope. A 100-ksi-modulus fill reduces pillar stress in both the 36-foot and l6-foot pillars (vein width is 10 feet) by about 50 percent relative to the open stope.

Jan 1, 1976

By L. F. Willmott

The Bureau of Nines at Morgantown, W. Va., has been investigating, on a pilot plant scale, various methods of gasifying bituminous coal with oxygen and superheated steam to produce synthesis gas, as part of the broader program of finding new uses for coal. Differences in the pressure gasification methods used have depended on differences in the manner in which the pulverized coal is fed to the gasifier. One of the methods of feeding the coal that was investigated was the continuous, integrated coal-water slurry system. Goal and water were first mixed to produce a slurry; then the slurry was pumped through a heated coil. to evaporate the water fraction; the resulting steam was superheated, and some of it was separated so as to adjust the ratio of the residual steam to the coal fraction and make the resulting mixture suitable for partial combustion with oxygen in a pressure gasifier. Both before and during this reported3 developmental work it was necessary to make an extensive literature search into the technology of aqueous slurries in order to establish design criteria for the pilot plant and to correlate results of various phases of the work with that of other investigators, The pilot work coincided with the commercial development of a long-distance pipe- line for the transportation of coal as a coal-water slurry, and this fact tended to broaden the scope of the pilot plant work and the extent of the literature search. This bibliography is the compilation of the material that was collected.

Jan 1, 1963

By L. F. Willmott

The Bureau of Mines at Morgantown, W. Va., has been investigating, on a pilot plant scale, various methods of gasifying bituminous coal with oxygen and superheated steam to produce synthesis gas, as part of the broader program of finding new uses for coal. Differences in the pressure gasification methods used have depended on differences in the manner in which the pulverized coal is fed to the gasifier. One of the methods of feeding the coal that was investigated was the continuous, integrated coal-water slurry system. Goal and water were first mixed to produce a slurry; then the slurry was pumped through a heated coil. to evaporate the water fraction; the resulting steam was superheated, and some of it was separated so as to adjust the ratio of the residual steam to the coal fraction and make the resulting mixture suitable for partial combustion with oxygen in a pressure gasifier. Both before and during this reported3 developmental work it was necessary to make an extensive literature search into the technology of aqueous slurries in order to establish design criteria for the pilot plant and to correlate results of various phases of the work with that of other investigators, The pilot work coincided with the commercial development of a long-distance pipeline for the transportation of coal as a coal-water slurry, and this fact tended to broaden the scope of the pilot plant work and the extent of the literature search. This bibliography is the compilation of the material that was collected.

Jan 1, 1963

By Kenneth Wardell

Those flat lying, bedded or replacement, non-fossil fuel deposits which exist within the U.S.A., and which are amenable to longwall mining, are identified by reference to three principal factors associated with their physical/geological environments. These are their depth, extent and structural continuity. Technical feasibility is assessed in relation to the likely cutting speeds which can be achieved in the identified minerals with existing longwall shearer machines. Economic comparisons are made between traditional mining operations in those deposits for which technical feasibility is demonstrable. Continents are made concerning those technical deficiencies which appear to preclude the application of existing longwall equipment to the identified deposits and suggestions are made regarding the lines of research aimed at improving longwall technology.

Jan 1, 1978

By Craig Hartley

? A helper stands beside a continuous miner as the operator is at the controls. The operator means to push the stop button but hits the drum rotation start button by mistake. The drum begins to turn and the bits catch the helper's clothing. He is thrown violently to the ground and suffers multiple contusions. ? A farmer's wife helplessly watches her husband drawn into the claws of farm machinery while she frantically and unsucessfully searches for the control to stop the machine. ? A mechanic on the night shift replaces plugs in the lubrication systems of all three engines of an airliner following routine maintenance. In doing so', he fails to notice that "0" ring seals have not been mounted on the plugs. A few hours later, as the fully loaded airliner is cruising high over the ocean, oil pressure on one engine drops precipitously. The pilots quickly shut down the engine and turn for home. Almost immediately, the two remaining engines lose their oil and fail.

Jan 1, 1983

By P. Condori

Palabora Mining Copper has a unique ore body composition which unlike other copper ore bodies has three main components in significant proportions; these are copper bearing ore, magnetite and dolerite. The high content of dolerite, a hard barren material, creates a high proportion of pebbles which normally are recycled back to the mill. This action increases the mill bearing pressure and power progressively until corrective actions are taken. A logical action to solve the pebbles generation would be to incorporate a pebble crusher. This in fact was done however two fundamental issues were encountered; the high content of magnetite and existence of a cyclone classification section. Due to the high content of magnetite, metal detectors have not been able to work efficiently to separate tramp metal which causes damage to the pebble crushers. The existence of cyclones in the circuit had a detrimental effect on the final product when the pebbles crusher was online producing coarse sandy material. Due to the difficulties in treating pebbles via conventional procedures and the unique Palabora ore composition and characteristics, sorting technology was investigated at laboratory and pilot scale. It was found that a combination of optical and electromagnetic sorting could efficiently separate dolerite from the copper bearing and magnetite ores. This paper reports the findings of the laboratory and pilot scale work performed and discusses the additional benefits to the circuit.

Jan 1, 2012

By CHAS. A. R. LAMELY

In the extreme northeast corner of the State of Washington, on the Canadian border, lies the Metaline mining district. This district is old in history, but young in production. The Metaline district is a zinc-lead area of the replacement type in dolomite and limestone. The ore bodies of the Josephine horizon are in many ways similar to the ore bodies of the famous Tri-State zinc fields. The beds are faulted and folded and have varyng low dips in varying directions, and underlie large areas of the district. Production started in 1927 on a very limited basis. The property is now mining and milling 700 tons per day. The mine is opened by adit tunnels and a vertical shaft. As the ore horizons gained depth, it was necessary to sink inclines to follow the ore horizon (see Fig 1). From 1927 to date, approximately 600,000 ft of diamond drill was put down This work indicated that sufficient tonnage existed to justify a redesigning of the whole operation, surface and under- ground. After four years of general study, the following program was planned :

Jan 1, 1949

By A. Paviani

The subject of this session is "Equipment Installa­tion, Recent Developments". This is a subject which is not usually addressed at conferences of Foundation Engineering. It is rare to find sessions dealing with the technological side of deep foundations, a subject which only recently seems to have aroused sufficient interest at national and international conferences. It is therefore natural for the subject of "Equipment", or the tools used to implement the various "technologies", to be over­looked or mentioned only occasionally during the discussion of other issues. At conferences, most of the attention is attached to research and to the theoretical interpretation of the performance and behaviour of deep foundations, as well as to establishing the most suitable calculation algorithms and approaches for the study, design and control of foundation structures. It is almost as if the subject of equipment is felt to be less important or, perhaps, that it is considered to belong more strictly to mechanical engineering than to civil engineering.

Jan 1, 1994