Search Documents

By W. F. Guenther

The usual hand-operated drilling outfit consists of a 4-in. post-hole auger with 3/4,-in. pipe for drill stem, in 4-ft lengths, with a turning handle fitted to a top pipe T. The auxiliary tools are: a chisel-bit drill made from 3/4 or 7/8-in. tool steel welded to a 4-ft length of 3/4-in, pipe, so that the regular pipe string can be used; also a churn or "mule foot" made from 3-in. pipe, slotted on one side, belled to a 4-in. tempered cutting edge on the bottom, all welded to a 3/4-in. coupling by a yoke. Other tools required are pipe wrenches and cleanout tools made from old auto springs (Fig I). A 4 1/2 or 5-in. collar welded to a plate is often used to protect the mouth of the drill hole. In general the auger is used in the typical clay overburden and brown phosphate matrix, which is relatively soft. The churn or "mule foot1' is used in hard pan, lump phosphate or cherty ground. The drill is used for breaking flint, often found loose in the overburden. The drill with the chisel bit is used for trimming sides of the hole, sounding for lime bottom and breaking through hard lumps. Holes have been drilled to a depth of 80 ft, but the limit of efficient operation is about 50 ft. In deep holes it is necessary to unscrew the string in 20-ft lengths, to

Jan 1, 1948

By Arthur R. MacPherson

Primary autogenous grinding has been in general use for somewhat over 20 years. During this period there have been many highly successful plants built on this principle, while some others have had problems such as: 1. Not performing as predicted from test work. 2. Highly fluctuating tonnage rates. 3. Mechanical problems. 4. High liner wear. Many of the problems with commercial autogenous mills have resulted from improper sampling and testing of the ore during the development period. It is recognized that the fully autogenous mill is very sensitive to any changes in grindability which may occur in the feed to such a mill. The semi-autogenous mill is somewhat less sensitive, but large swings in grindability of the feed require adjustment of ball charge and this cannot be easily accomplished in a short period of time.

Jan 1, 1976

By James Douglas

Discussion of the paper of James Douglas, presented at the New Haven meeting, February, 1909, and published in Bulletin No. 29, May, 1909, pp. 439 to 451. JAMES DOUGLAS, New York, N. Y. (communication to the Secretary*) :-In my paper on the Conservation of Natural Resources, I referred to the slow replacement of bee-hive ovens by the by-product ovens as a most notable instance of waste. And I quoted from Mr. Parker's report for .1906 an explanation given by him in accounting for the small production of by-product coke. It was that the markets for the by-products of the coke-ovens was so limited that some of the ovens constructed were out of operation. His report on the manufacture of coke in 1908 1 does not record an improvement, and attributes the strange fact that we alone, of all the industrial peoples, delay the adoption of this cardinal improvement from the continuance of the same almost inexplicable cause. To quote again from his report, lie says (p. 241): "The year 1908 was not marked by any notable gain in the construction of by-product coking plants, though some new work was done. There was a net increase of 115 in the number of completed ovens in 1908 over 1907, the totals for the two years being, respectively, 3,892 and 4,007. The additional equipment consisted of 140 Koppers regenerative ovens built at Joliet, I11., by the United States Steel Corporation, but this increase was partly offset by the dismantling of Y5 Semet Solvay ovens at Sharon, Pa., the net gain being 115 ovens. Included in the total of 4,007 completed ovens in 1908 are 152 Newton-Chambers ovens at Vintondale, Pa., but as no recovery of by-products was made at this plant in 190S, the production of coke is included with that from beehive ovens. The 56 ovens of the same type at Pocahontas, Va., have not been in practical operation since they were first. installed. In addition to these there was one other by-product plant of 120 ovens. Oat. was not operated during the year. The number of retort ovens producing coke in 1908 was 3,679, as compared with 3,811 active ovens in 1907." In describing the anomaly he says (p. 249): It has been contended that the development of the by-product coking industry would have shown more rapid progress if markets for the by-products were * Received Feb. 2, 1910. Mineral Resources of the United States for 1908, Part I1., U. S. Geological Survey (1909).

Apr 1, 1910

By Kenneth N. Han

The effect of anions such as sulfate, chloride and nitrate on the solubility of rare earth element (REE)-bearing phosphates and fluoro-carbonates was examined using relevant thermodynamic data. The study found that these anions have significant influences on the overall dissolution of REEs from various sources in the aqueous media.

By V. C. Pandolfelli, P. Bonadia, F. A. O. Valenzuela, L. R. Bittencourt

Refractories for aluminum cells, if not properly selected, can lead to increased energy consumption and even shorten the pot life. Based on recent advances in understanding the deterioration mechanism of cathode materials, several commercial bricks in the SiO2-Al2O3 system were compared to the one used by an Alcoa smelter. Both physical and chemical properties were considered in the selection of the refractories. A more reliable method of permeability measurement, which takes into account inertial and viscous effects during the fluid flow, was applied. Additionally, the traditional cup test and other characterization techniques, such as thermal conductivity, X-ray diffraction, and mercury porosimetry, indicated that a brick with a relatively low alumina/silica ratio, presenting low open porosity and low permeability, far exceeded the performance of the brick currently in use.

Jan 1, 2004

By H. L. Marcus, P. W. Palmberg

As can be seen from the phase diagram A1-W1 the equilibrium solubility of tungsten in aluminum is practically nil at room temperature. By quenching from the liquid state (50,000°C per sec), Varic, Burov, and Kolesnicenko2 obtained A1-W solid solutions up to 0.15 at. pct W. The quenched alloys were in the form of foils, 0.2 to 0.3 mm thick. Considering the results of Duwez and Willens,3 it is obvious that this thickness, which makes impossible a sufficiently rapid quenching, was the main reason for the relatively low content of tungsten dissolved in aluminum found by Varic.2 he present note shows that the metastable solubility of tungsten in aluminum can be appreciably extended in aluminum-rich A1-W alloys. The quenching technique and the procedure employed for the preparation of the alloys have been described previously.475 The resulting quenched flakes varied in thickness from 1 to 20 µm from experiment to experiment. However, the measurements of the lattice parameters were carried out only with flakes thinner than 5 µm. The areas of quenched flakes were between 0.1 and 15 mm2. The quenched flakes were placed into a 0.3-mm glass capillary tube which was then mounted in a 114.6-mm-diam Debye-Scherrer camera. Straumanis asymmetric film position and nickel-filtered CuKa radiation were used. The lattice spacings were computed taking X(CuKa1) = 1.54050A for resolved and ?(CuKa) = 1.54178A for unresolved doublets. All specimens were rotated at room temperature, 26" +2°C. The lattice parameters were estimated from extrapolation against the Nelson-Riley function. It was estimated that the error in the lattice parameter of the measurements on a single film lies within +0.0004A for lower and about +0.001A for higher concentrations of tungsten. The lattice parameters of the metastable solid solutions A1-W are plotted vs the concentration of tungsten in Fig. 1 together with the parameters measured by previous investigators.' Each point of the present measurements represents a determination of the lattice spacing on different quenched flakes, for a given concentration of tungsten. With experimental accuracy, the lattice parameters of the metastable solid solutions fall on the straight line passing through the already known data.' As estimated from the uncertainties in the lattice spacings of the solid solutions, the alloys were homogeneous within 0.1 at. pct W. The solubility of tungsten in aluminum-rich A1-W solid solutions obtained by a very rapid quenching technique is increased to about 0.95 at. pct W. This value is 6 times greater than the amount known up to now. -he lattice parameters of the resultant aluminum solid solutions with higher concentrations of tungsten than 0.95 at. pct W did not remain constant AUGER electron spectroscopy has been used to clarify the role of impurities in the embrittlement of AISI 3340 steel. Analysis of fracture surfaces has shown that the embrittled condition is correlated with appreciable antimony segregation at grain boundaries. The low temperature (400" to 600°C) temper embrittlement of low alloy steels containing various combinations of Cr, Ni, Sb, Mn, P, Sn, and As has been examined extensively for many years. General reviews of the area have been made by McMahon1 in 1968, LOW' in 1959, woodfine3 in 1953, and Holloman4 in 1946. Recent work by Low, Stein, Turkalo, and LaForce5 has done much in separating the alloy and

Jan 1, 1970

By Donald Strickland, Peter Kresin, Dave Hall

"Have your parents or grandparents ever tried to share with you their wisdom and you ignored it because it did not relate to you‘? I have been ignorant and inevitably grew older and wished I had listened. The result: learning the hard way. As British Astronomer Fred Hoyle once said. “It is the true nature of mankind to learn from mistakes not from example.“ Hopefully we will continue to learn from the examples shared by our fellow mineral processors in these conference proceedings. It is the intent of this paper to share wisdom from the Musselwhite Mine that you may apply to your own operation.This paper is divided into three sections:1. Feasibility3. Operation3 . DesignKey points of the Feasibility and Design stages are summarized. followed by an analysis of actual operating statistics. An attempt is made to relate these statistics back to the feasibility and design with emphasis on areas of success and those with potential for improvement."

Jan 1, 1999

By C. Dupuis, P. Waite, S. Leboeuf

Casthouses throughout the aluminium industry commonly use chlorine gas as a fluxing agent for furnace and in-line treatment of molten aluminium alloys. Its positive impact on the removal of alkali elements and non-metallic inclusions is well known. Nevertheless, the elimination of its use is highly desirable due to the safety and environmental risks associated with storage and handling. Over the past decade, the aluminium industry has significantly reduced its chlorine consumption. This has been achieved by maximizing the chlorine gas utilization efficiency during metal processing, and by the chlorine replacement for crucible and furnace metal treatment applications. Operation of sealed in-line treatment units without chlorine is now possible, but with lower or inconsistent removal efficiency penalties for alkali and inclusions respectively. This paper reviews the progress made at Arvida Research and Development Centre regarding the reduction of chlorine and the development of an alternative to chlorine for in-line metal treatment without penalizing the metallurgical performance.

Jan 1, 2006

By Wayne Bell, Matthew Andriese, Shuqian Xie, Jiann-Yang Hwang, Zhiwei Peng

"Pyrolyzed carbons are generally known as good microwave absorbers and their dielectric properties still remain to be fully explored. In the present study the dielectric properties and dielectric polarization-relaxation phenomenon of a typical activated carbon was investigated. The experimental results indicate the complex permittivity is highly dependent on temperature and frequency. The decrease of permittivity with increasing temperature from room temperature to ~100 °C is probably ascribed to the release of the water vapor adsorbed on the surface of activated carbon, and the variations of permittivity with temperatures between 100 °C and 450 °C in the frequency range of 300 MHz to 3000 MHz are mainly attributed to the decreased relaxation time of dielectric polarization.IntroductionPyrolyzed carbons have been identified as excellent microwave absorbers owing to their high dielectric and electrical loss under microwave irradiations. Among them, activated carbon continues to attract more and more attention from researchers. Due to its special physical properties, the production, modification and regeneration of activated carbon with the assistance of microwave have been widely studied over the last few decades [1-6]. However, only few attempts have been applied to explore the dielectric properties of such materials due to the complexity and variability of their organic precursors and activation processes [7,8]. In order to shed a light on this problem, a typical sample, Norit® A Supra USP powdered activated carbon, was adopted to perform dielectric characterization, which may provide useful information for its wide application in the fields of purification, energy (hydrogen) storage and so on."

Jan 1, 2011

By Ralph Sweetser

THE present state of iron blast-furnace practice is metallurgical rather than mechanical; the tend-ency is toward intensity rather than toward ex-tension. The engineers have built blast furnaces big enough and strong enough, and have furnished accessory equipment ample and accurate enough for the present state of the art, but the metallurgical side has been too much neglected; the metallurgist, rather than the engi-neer, is now the man on whom the present and future progress in iron blast-furnace practice depends. The mining engineer has produced great tonnages of iron ores, and has kept ahead of the demands for quantity; now the metallurgist is improving the chemical and physical qualities of this product by ore-dressing and other forms of beneficiation. For a generation or more, the principles of mechanics have had most influence in the advancement of iron blast-furnace practice; atten-tion now is given more to the principles of metallurgy, chemistry, and ore-dressing. This metallurgical progress is taking place inside and outside the blast furnace. The two great determining factors of the inside operation are the slag, and the rate of combustibility of the coke. Outside the fur-nace, the progress is, and will be, along the lines of more careful mixing of ores and iron-bearing materials, in the sizing and washing of limestone, and in the char-acter and structure of byproduct coke.

Jan 3, 1922

By J. P. McKinney

A mathematical model is presented for the electrokinetic dewatering of suspensions of phosphatic clays. The modeling approach couples a boundary-element model for solution of Laplace?s equation to a recently developed constitutive equation that relates the change in solids content with applied electric field and time. The observation that the electric field controls both the maximum solids content achievable and the time required to reach that value is shown to severely constrain the application of electrokinetic dewatering strategies to an entire clay settling area. The approach, however, may be feasible for implementation as part of a continuous plant process.

Jan 1, 2011

By J. B. Macelwane

GEOPHYSICS differs from geology and physics in many respects. In the first place, geophysics is a complex science embracing the fields of seismology, geomagnetism, geoelectricity, geodesy, meteorology, volcanology, physical oceanography, physical hydrology, tectonophysics and exploration geophysics. Geology is also a complex science and so extensive in its various fields that no one can master them all, and no part of geology deals in any sense with several of these fields of geophysics. In the second place, geophysics makes use of methods and instruments that are derived primarily from the science of physics. Geology, on the other hand, has methods of its own and it draws its borrowed techniques and its instrumental equipment not only from physics but also and perhaps primarily from chemistry and biology. The difference, therefore, between the geophysicist and the geologist lies partly in the phenomena that are observed, partly in the methods and instruments with which each carries on his exploration; but partly also, and perhaps principally, in the habitual attitude of mind and in the background of specialized training with which each approaches the problems presented by this planet of ours. The geologist as such, therefore, is no geophysicist. On the other hand, the physicist is not a geophysicist either. Isolation of each problem in a closed laboratory system under complete control is fundamental to the methods of the physicist. The geophysicist must apply physical instruments and physicomathematical reasoning to the study of physical quantities in their undisturbed natural environment. What, then, is a geophysicist? In the sense that he is a trained expert in all of the geophysical sciences, I do not believe that such a person ever existed. It would be beyond the possibilities of a single lifetime. I think there is confusion in our ideas and in our use of terms. We are not all thinking of the same thing when we say geophysics or geophysicist; yet we seem to talk as though we were. It is as absurd to say that the whole of geophysics belongs to geology because the field of a particular type of geophysicist-the exploration geophysicist -calls for some knowledge of geology as it would be to say that the whole of biology belongs to geology because a particular type of biologist-the paleontologistneeds some knowledge of geology. DEVELOPMENT OF A GEOPHYSICIST Since it is impossible to become an expert in all the fields of geophysics, and since students entering college seldom know the field they will choose as a career, what would we suggest as the best general preparation for work in geophysics, whether as a meteorologist, an oceanographer, a seismologist, a geodesist, a geomagneticist, a volcanologist, a tectonophysicist, a hydrologist, or an exploration geophysicist? We may distinguish five phases in the development of a geophysicist: (I) his mathematical and scientific studies in high school; (2) the general mathematical and scientific

Jan 1, 1941

By R. J. Mitchell

"Centrifuge modelling of earth structures is a well-proven technique for evaluating the performance of prototype structures using physical models. The applications of this technique have increased dramatically during the last decade such that even the modelling of dynamic responses in structures has been accomplished.This paper presents the first model test results used to design a mine backfill. The models were tested using a 3 m radius 30 g-tonne geotechnical centrifuge which was constructed at Queen's University specifically for model studies on mine backfill stability and subsidence. The models represent the first production blast-hole stope to be mined at Westmin Resources Ltd. 's H. ~ Mine on Vancouver Island. This paper includes photographs of:model failures in the centrifuge and correlations of model test results with analyses based on unconfined and triaxial test data.IntroductionDuring the feasibility study and development stages for the H.W. Mine, Westmin Resources Ltd. conducted a comprehensive rock mechanics and backfill engineering program. The results of these studies indicated the need for assurance of backfill stability during pillar recovery on the initial blast-hole mining block. The cemented tailings backfill had to be free standing for heights up to 25 m and the potential for surcharge loading from a weak hanging wall zone, the potential for fill block sliding down-dip and the potential for seismic loading had to be considered in the design of the fill strength. The basic questions to be answered were: what cement content is required and will the resulting backfill costs be economic relative to the proposed mining method and sequence? Figure I shows a typical cross-section through the first mining block . The up-dip stope is to be mined first and backfilled with cemented tailings . The down-dip stope would then be mined and filled. Depending on ground conditions encountered, the complete intervening pillar could be recovered and the void backfilled with uncemented tailings or it could be recovered in small sections by exposing limited back and wall areas, backfilling with waste rock and I or cemented tailings . This latter method is commonly referred to as the Avoca method"

Jan 1, 1987

By Jongmin Jeong, Jaehong Shin, Joo Hyun Park, Chul-Woo Nam, Kyung-Ho Park

Because sulfur and phosphorus are very harmful in steel products, there are increasing requirements for refining these elements from ferroalloys industries. Hence, in the present study, simultaneous desulfurization (de-S) and reducing dephosphorization (Rde-P) from silicomanganese (SiMn) alloy were investigated using metal-slag equilibration method under highly reducing condition at 1773 K. Experiments were carried out by equilibration between SiMn alloy and MnO-based slag in graphite crucible under p(O2) = 10−18 atm. Slag composition was designed by changing basicity (CaO/SiO2) and MnO content at fixed Al2O3 (=20%) and MgO (=5%) contents. De-S ratio increased with increasing basicity until C/S = 1.5 whereas Rde-P ratio was not significantly affected by slag basicity. This was because thermodynamic driving force of de-S reaction was greater than that of Rde-P reaction under present experimental conditions. The de-S and Rde-P ratios commonly increased with decreasing oxygen partial pressure.

Mar 1, 2017

By A. Duerksen

"Surface coal mining in West Virginia has supplied energy to the eastern coast of the United States for over a century. Over the years, the coal mining industry has been forced to adapt as societal demands regarding health, safety, and environmental impacts have changed. More recent pressure has called for another iteration of change: long-term post-mining sustainability. The research discussed in this paper investigates one potential solution - or component of a solution - to improve the sustainability of surface coal mining in West Virginia: post-mining wind power. The paper begins with an introduction to the Appalachian region of the U.S. and the role that mining has played in its history, followed by a discussion of the need for sustainable mining and how post-mining wind power may help fulfill it. Data processing methodology of field data from monitoring locations is then explained. The results are then used to estimate the electrical output of a wind turbine. This data is then utilized in a case study discussion of one of the monitored sites. The paper concludes with an analysis of the broader implications of the research and a discussion of future work."

Jan 1, 2011

By Maria das Graças da Silva-Valenzuela, Mathilde Julienne Gisele Champeau Ferreira, Simeão Lopes Ferreira, Francisco Rolando Valenzuela-Díaz

The use of clays to formulate powder coating can improve physical properties, besides a final product with more sustainable characteristics due to the elimination of some additives, which may be substituted for the clay. We investigate the use of a modified smectite clay to formulate powder coating based on polyester resin. Four compositions of incorporated claywere evaluated (0, 4, 7, and 10wt%). Powder coating were prepared in a twin-screw extruder at 105 °C, and characterized by XRD, FTIR and SEM. Tests of flexibility, adhesion and impact strength in accordance to ASTM standards were performed. Diffractograms of the samples showed the characteristic peak of the modified smectite in d(001) * 37°(2h), indicating exfoliation of the clay. Micrographs by SEM showed the presence of lamellar structure for the clay-based powder coating.Mechanical assays were found for all analyzed coatings, indicating that sample containing 7% of clay presents the best performance.

Mar 1, 2018

By R. S. Fitzpatrick, P. Hegarty

"Gravity separation is a key technology in the recovery of a range of mineral ores including coal, tin, tungsten and tantalum. One of the problems associated with gravity concentration is that recovery is traditionally lower than for other separation techniques such as the flotation of base metals. Any improvements in recovery will, therefore, have a significant effect on the economics of operations of this type. More accurate, robust modelling of gravity separators is one means of achieving greater recoveries. Furthermore, better modelling can lead to more informed equipment selection and process design for potential economic deposits.Previous models for gravity separation equipment have typically relied on simple metal mass balances from samples of the separated products. However, with advances in technology there is a ready availability of analytical instruments for the automated quantitative determination of mineralogy. Instruments such as the Mineral Liberation Analyser and QEMSCAN make it possible to estimate particle size and density (related to mineral liberation and association) which are the primary factors in gravity separation. Models produced using quantitative mineralogy of feed streams will be potentially superior to those produced historically.This paper describes test work undertaken on a wet shaking table using a synthetic ore. The objective of this test work was to develop a model to predict the effect of changes in feed ore characteristics on shaking table performance by measuring quantitatively the mineralogy of the feed material. Particles were divided into size/density classes based on the results of QEMSCAN analyses.It was found that it was possible to use data from QEMSCAN to predict the recovery of size/density classes and to predict the effect of changes in the relative abundances of these classes on the separation. This model can potentially be used to adjust operating variables to maximise grade and recovery by monitoring the input feed. Care was needed when utilising QEMSCAN data to ensure representivity."

Jan 1, 2016

By E. Sarris

Tailings dams are large-scale earth-fill embankments that are designed to contain mining wastes from ore dressing plants. Most commonly tailings dams are constructed in stages in order to keep up with the increasing volume of mine tailings. Staged construction using various methods (like up-stream, down-stream, and centerline) is generally considered as a very effective way to construct this kind of embankments. The present study is devoted to the investigation of the behavior and the stability of these geostructures under static conditions. In order to accomplish this task, elaborate two-dimensional numerical models are examined, utilizing the geotechnical finite-element code PLAXIS. Numerical analyses are conducted for all three types of tailings dams in order to obtain the potential modes of failure, while the corresponding factors of safety are determined by the shear strength reduction technique.

Jan 1, 2005

By Michael J. Cruickshank

Marine minerals are more than an academic curiosity as they represent the most significant global source of mineral materials for economically and ecologically sustainable development for the future. Minerals research is traditionally carried out by industry and thus, in the United States at least, applied research in marine minerals may not get the share of government funding or attention that more exotic programs for space exploration or future global disasters engender. Two recent events have significantly changed the status of marine minerals. Discoveries made in the last thirty five years indicate that the potential for mineral occurrences in the oceans and seabeds, area for area, is as high as for terrestrial lands. On this basis the global mineral resource base has been recently increased by a factor of four of which three quarters is underwater. The recently enacted Law of the Sea has mandated what is probably the most far reaching re-distribution of natural resources in human history, and has resulted in a peaceful subdivision of seabed jurisdictions between the coastal nations of the world which should significantly affect future mineral markets and the balance of economic powers. Significant applied research efforts are ongoing for marine minerals as an adjunct to commercial production in southern Africa for diamonds; and in many other parts of the world for sands for beach and coastal protection. Forward planing, including research and development activities focussed on future commercial production of metalliferous oxides, continues in Korea, China, Japan, India, and with lesser activity, in the United States, United Kingdom, Germany and the CIS. Annual expenditures for this work amount to millions of dollars. In all cases the environmental aspects of commercial produc¬tion are a significant part of the research. Geologic studies on the occurence and distribution of metal sulfides at plate boundaries continue on a regional basis in the Pacific.

Jan 1, 1996

By Corinne Boone

CO2e.com, LLC - launched in November 2000 - aims to be ?the global hub for carbon commerce.? CO2e.com is a subsidiary of the Cantor Fitzgerald Group, one of the world?s leading brokerage firms Recent Investor in CO2e ? Mitsui & Co. Alliance with Cantor Fitzgerald Environmental Brokerage Services Group (CFEBS) Offices in London, Toronto, Tokyo, New York, San Francisco, Los Angeles, Connecticut, Houston Primary Goals/Benefits of ET § Goals of Emissions Trading: ? Permit Industrial Growth/Expansion ? Promote Economic Efficiency and Flexibility in Meeting Air Pollution Standards § Benefits of Emissions Trading: ? Enhance Air Quality w/o Economic Stagnation ? Encourage Development of New Technology ? Foster Most Efficient Use of a Limited Resource -- Clean Air § Contributes to Sustainable Development and objectives of UNFCCC, Kyoto Protocol?.

Nov 1, 2002