Search Documents

By Leonard B. Griffiths

In a recent communication, Smith and Wood described some results of 800°C compression/creep tests on WC-12 wt pct Co alloys in which plastic flow in the WC particles was believed to have occurred. The deformation observed in the WC particles was found to be a function of the rate of loading. The authors suggested that their data constituted support for the Ansell6-Lenel theory of yielding in dispersion-strengthened alloys. I do not agree with this interpretation since the Ansell-Lenel theory does not apply to the type of alloy in question. In this alloy, the dispersoid is present to the extent of about 80 vol pct. Even where there is no continuous skeleton, which apparently is the case in this instance, the simple fact is that nearly all of the load is carried elastically by the stronger material (wc).7 The constraint imposed upon the matrix, by virtue of the differences in Young's modulii and Poissons ratios, severely limits the stress level to which it may be subjected (assuming that the interfaces remain intact). If one allows for the constraint and then performs the same computation as in Smith and Wood, one finds that the stress on a WC particle is about 4 x 105 psi. This is about 21/2 times lower than the predicted fracture stress for WC. I would completely agree with the final paragraph of Smith and Wood, namely, that loading rate is of considerable significance. However. a more likely interpretation of their data is, I submit, that in the absence of stress relaxation (by secondary slip or climb) those WC-Co interfaces subjected to a normal tensile stress begin to fail. Once this occurs, the stress distribution will change rapidly and "premature" fracture of the WC then becomes quite probable. Tne serrated edges shown in Fig. 1 may very well be fine, interface fissures.

Jan 1, 1970

By Walter L. Maxson, Fred C. Bond

THIS paper is a continuation of two earlier papers, l, 2 and presents new data on the grindability of various ores and other materials-the results of several years of intermittent research work on the nature of grinding and interpretation of test results. It is divided into five parts: 1. The tabulated results of several hundred grindability tests on a wide variety of ores. 2. A method of correcting screen analyses and calculating from them the surface and other properties. 3. A description of a new method of measuring the "surface energy" of an ore by pendulum impact tests. 4. Test results. 5. A general discussion of the test results and their application to grinding problems. 1. GRINDABILITY OF VARIOUS ORES This part is a continuation of the paper listed as reference No. 1. The method of testing is described in detail in that paper. The sample to be tested is crushed to all through 6 mesh in rolls set at x6-in. opening in closed circuit with a screen. Of this sample 700 C.C. is ground dry in a laboratory ball mill under constant conditions of mill speed and ball charge in closed circuit with a screen of the desired size at 250 per cent circulating load. The mill is cylindrical, 12 by 12 in., and rotates at 70 r.p.m. It contains a charge of 285 iron balls weighing 20,125 grams and ranging from 1 ½ to ¾ in. in diameter. Each test is continued for a sufficient number of periods to establish equilibrium at 250 per cent circulating load, or until the composition of the circulating load is constant for successive periods. Tests are conducted at the mesh size to which the ore is to be ground in practice, and the results are expressed as the net production in grams of screen undersize per revolution of the mill. This is designated as the

Jan 1, 1938

By B. J. Arnold, F. F. Aplan, R. R. Klimpel, E. C. Jr. Dowling

Residence-time distribution techniques are useful tools in the analysis, characterization and modeling of the performance of processing equipment and circuits. This paper presents the results of both conventional and more-sophisticated residence-time distribution techniques for industrial copper-flotation-circuit data. While conventional techniques provide a description that is sufficient for macroengineering design requirements, the more sophisticated tracer-technique methods give more realistic descriptions of process flows and system effectiveness. It is demonstrated that these approaches can provide highly useful information about different equipment, as well as its configuration and performance.

Jan 1, 2000

By R. Dekkers, J. Plessers

The feasibility of using hydrogen to obtain clean steels is investigated. High hydrogen contents are generally considered as detrimental due to the risk of flakes, bubbles and breakouts during casting. Hydrogen can nonetheless be removed by degassing of the steel. The results of industrial campaigns, where total oxygen content and hydrogen content were monitored, are presented. High resolution microscopy of inclusions and laboratory experiments on the rate of inclusion removal by CaO-Al2O3 slags at different partial hydrogen have been carried out. So far, evidence that hydrogen may influence inclusions or the steel cleanliness is not clear. Keywords: hydrogen, cleanliness, inclusions.

Jan 1, 2004

By Matthew S. Sanchez, Richard J. Lee, Matthew D. Zock, Drew R. Van Orden

"Current Environmental Protection Agency (EPA) risk models and asbestos fiber counting techniques for monitoring airborne exposures treat all fibers as being equivalent and ignore the effect of dimension on toxicity. While this may have been appropriate when modern analytical methods were not available, the measurement world is now fully capable of making the appropriate distinctions. The importance of width as a determinant of carcinogenicity has been recognized for nearly 30 years within the published literature. Stanton,1 in a landmark study of a suite of fibrous materials, found that durable mineral fibers with widths less than 0.25 mm and lengths longer than 8 mm were causally associated with the induction of tumors. Pott,2 in a later study, postulated a fiber toxicity model that agreed reasonably well with the Stanton findings, but extended the concept to include varying toxicity as a function of length and width. Wylie et al.3 reanalyzed samples used by Davis et al.4 and found that tumor generation was strongly and inversely correlated with fiber width. Crump5 testified increasing fiber length was correlated with disease occurrence. Lippman6 reviewed a number of studies and suggested that mesothelioma was closely associated with long, thin fibers. Berman et al.7 published a risk model, which found that disease was correlated almost exclusively with fibers longer than 40 mm and width less than 0.25 mm. Recently, Loomis et al.8 reanalyzed textile mill samples and found that aspect ratios greater than 40:1 were highly correlated with disease. Incorporation of width into risk models has been limited by the availability of data from operating asbestos plants and, in particular, the observation of an asbestos plant for which there is no observable mesothelioma. There have been only limited studies published on the dimensions of asbestos fibers, with a few serving as the primary references in other literature.9_13 A rare opportunity to collect detailed concentration and dimensional data of airborne crocidolite from an operating asbestos-cement plant using modern analytical procedures arose, providing a chance to supplement the existing literature on airborne fiber dimensions. The asbestos-cement plant is located in the eastern end of Cochabamba, Bolivia along Highway 4. Cochabamba is a relatively large city located in the Andes Mountains, approximately 250 km southeast of the capital La Paz. The city sits in a valley that runs east-west with mountains to the north and south. The crocidolite used in the products made at this facility is mined in central Bolivia, approximately 75 km northwest of Santa Cruz. The crocidolite is a fibrous magnesioriebeckite 14 (blue asbestos). Crocidolite fibers from Bolivia were the subject of prior reports suggesting the fibers are generally longer and thicker than crocidolite from Australia or South Africa.9 At the cement plant, the run-of-mine crocidolite was first pulverized using a hammer mill and then sieved on vibratory sieves to produce fibers of limited size ranges for use in the cement. The sieved crocidolite is mixed with other components, including recycled cement product, to produce a slurry that is vacuum filtered into sheet form. The sheets are then manually molded into a corrugated shape, air dried, and sawed (using circular saws) to accepted dimensions. The sawed sheets are cured in soaking pits for 28 days before being shipped to the consumer. Prior to shipping, the sheets are finished by a light hand sanding followed (at customer request) by applying one or more coats of paint. A detailed description of the cement plant and the industrial hygiene results can be found in Van Orden et al.15"

Jan 1, 2012

Essential features of the role of the fill material in mechanized cut and fill mining are discussed, with particular emphasis on its dewatering and strength development after emplacement. The fill material is regarded as a chemically-reactive porous medium, the most important property of which is permeability. Methods are described for measurement of permeability and other fill properties and results of such measurements applied to develop an orderly approach to the operation.

Jan 1, 1966

By C. W. Hunt

I wish to register strong disagreement with the choices of drilling sites chosen by the Continental Scientific Drilling Committee, while endorsing the stated objectives. Of special significance is the lack of any site involving the metals most needed today in the US, while 9 to 13 km of drilling are allocated to gold and silver districts and 11 to 17 km to base metal (mainly copper) districts. Why is nothing proposed for platinum group or chromite? Is this because the committee did not know of such a site? If so, I offer such a site in California (see Fig. 1). The mineralization shown in Table 1 occurs in a large peridotite body in western Tehama County, CA. Petrography has demonstrated unequivocal evidence of migrated PGE deposited in peridotite and chromite of hypabyssal nature. Active diapirism (due probably to serpentine buoyancy) above a reactivated mantle to surface conduit marks the position of the conduit. Young explosion breccia cemented loosely by volcanic glass and tuff demonstrates the significance of the conduit as the prime source of the various emissions. Deep drilling could result in major metals discoveries as well as shedding light on the grand questions of platinum group mineralization. What role water has played in this occurrence is not yet certain; but chlorine and asphaltite have been detected in and adjacent to native PGM, suggesting a major role for water. The explosion breccia suggests that this excellent site could overlie entrapped geothermal steam.

Jan 1, 1988

By I. Iwasaki, T. Fujuita

The removal of phosphorus from steelmaking slags is essential for recycling such slags to blast furnaces for recovery of their manganese, iron, and lime contents. Phosphorus is mainly concentrated in the dicalcium silicate phase of the slags (Fujita and Iwasaki, 1988, 1989; Suito, et al., 1977). Slow-cooling of steelmaking slags in an air atmosphere increased the grain sizes of constituent minerals; however satisfactory magnetic separation results could not be attained because of the close association of a strongly magnetic ferrite phase with dicalcium silicate (Fujita and Iwasaki, 1988). Curie point of the strongly magnetic ferrite phase in the slow- cooled steelmaking slags was investigated and an attempt was made to separate the phosphorus-bearing dicalcium silicate phase in ground slag pulps heated to a temperature exceeding the Curie point. Materials and methods Slag samples, heated to its fusion temperature of 1370°C and slow-cooled in an air atmosphere, were ground dry to -90 µm (about 170mesh) in a ring grinder. The ground sample was pulped to 1% solids in distilled water using 1 kg/t sodium hexametaphosphate as a dispersant and separated in a Sala high gradient magnetic separator, Laboratory Model 10-15- 20B, using a 100-mesh expanded metal matrix and 300 m/h flow rate.

Jan 1, 1990

By C. H. Bowen

NDUSTRY needs a generally applicable means of defining average grain size and grain size distribution. Students of sediments hade explored this field, employing methods that might also prove useful in engineering problems. Before attempting to solve specific problems it is well to review the derivation of commonly used grade scales and the reasons for their selection. This aspect of the problem seems largely to have been lost, and a review of basic factors may suggest causes for failures in using size analysis data. Three facts are implicit in selection of a grade scale: 1) Most particulate mixtures are continuous distributions of sizes, and any grade scale that may be employed is an arbitrary means of visualizing that distribution. 2) For purely descriptive purposes, any grade scale, regardless of the rationality of the class intervals, will be satisfactory if it is accepted by a sufficient number of workers. 3) For analytical purposes, class intervals must be small enough to define the continuous distribution accurately. Further, where statistical studies are involved, a fixed relationship should exist between classes or grades. An argument in favor of geometrically related size grades lies in the fact that most particulate mixtures contain such a wide range of sizes that use of an arithmetic diameter scale is practically impossible. Udden, who recognized this fact in 1898,' proposed one of the first grade scales based on a regular geometrical interval. Udden used 1 mm as his basic diameter and a ratio of 2 (or 1/2) between classes. In 1922 Wentworth2 re-examined Udden's grade scale, retaining the same class interval and basic diameter, but extending the scale in both directions and renaming the classes. In 1930 (Ref. 3, p. 82) the American Society of Testing Materials proposed what is now known as the U.S. Standard fine sieve series, also based on the 1 mm diam, with a v2 ratio between sieves. This, then, is a one fourth Udden-Wentworth series in the sizes below the 4 mesh sieve. The U.S. Standard coarse sieve departs from the 1 mm base and uses inches; hence it is not a direct continuation of the fine series. The U.S. Standard series would thus seem to possess all the attributes of a good grade scale, which it is. It has a large number of classes (sieves). in fact too many for practical use in its entirety. This v2 subdivision of the Wentworth grades has led to the common use of two v2 sieve series, the half-Wentworth and the engineers' series. Geologists and sedimentologists favor the half Wentworth, or 18, 25, 35, 45 sieves, etc., whereas the engineers, preferring round numbers, utilize the other half of the U.S. Standard grade scale in the 16, 20, 30, 40 sieves, etc. The fixed geometrical ratio between classes is an advantage in statistical analysis, but the unequal classes cause some complications in calculations. This is especially true when moment measures are used. It was to simplify these calculations that Krumbein in 1934 devised the phi scale. Phi is defined as being equal to —log2 of the diameter in millimeters. Selection of logarithms to the base 2 relate the phi scale directly to the Wentworth grade scale in such a manner that the whole or fractional diameter values 2, 1, 1/2, 1/4 mm, etc., become rational whole numbers, —1, 0,1, 2, etc. Since this is an arithmetic rather than geometric series, calculations are facilitated. When the logarithm is multiplied by —1 the phi values below 1 mm become positive, those coarser than 1 mm negative. Because of its relationship to the Wentworth grade scale (and in turn to the U.S. Standard fine sieve series) it is not necessary to use the transformation equation to calculate the phi value for each individual sieve; this can be done graphically as shown in Fig. 1. It should be noted that this graph may be extended in either direction to include the range of sizes most commonly used by the individual worker. Application to Statistical Analysis Any attempt at systematically relating size analysis data to properties involves a statistical study whether it is recognized as such or not. Since this is true it would seem more logical to use measures and devices related to the general body of statistical theory. Several methods are available for studying particulate mixtures. One of the most commonly employed, and also the most often misused, is the histogram or block diagram. If its limitations are recognized and provided for, the histogram is a very useful tool. According to conventional practice, the bars of equal width are plotted and the values noted in terms of diameters, when in point of fact, log diameter is implied by such notation. Further, the histogram is sensitive to choice of grade scale and size of class interval, either of which may color the result. Grade scales whose classes are not related by fixed intervals are particularly difficult. Another basic weakness of the histogram is that it pictures a continuous distribution as a series of discrete grades.

Jan 1, 1957

By Peter Ryan

A patented process for agglomeration of Smelter ESP dusts is described. Addition of suitable binders followed by compaction, transforms fine, difficult to handle material into a dry, flowable agglomerate suitable for plant reentry. Details for the agglomeration process metallurgy and laboratory pilot plant testing are discussed. An example of full scale plant operations is described.

Jan 1, 1999

By W. C. Kerr

WHEN Agassiz and his party of geologists commenced their exploration of the interior of Brazil and the Amazon region, one of the first and, to the last, one of the most novel and striking phenomena which met them everywhere was the great depth of decomposed or partially decayed rock in situ, which mantles, and for the most part conceals, the underlying strata. The same facts strike all geological observers from the North who happen to penetrate the middle and southern latitudes of the Atlantic States. In North Carolina, e. g., the entire middle and western regions, outside of the Quaternary clays, sands, and gravels of the East,-that is, all that portion of the State occupied by the Arch can and Mesozoic rocks,-show everywhere this peculiarity, so new to those accustomed to glaciated surfaces. Not only do the hills and slopes, the mountain chains and

Jan 1, 1880

By W. C. Kerr

When Agassiz and his party of geologists commenced their exploration of the interior of Brazil and the Amazon region, one of the first and, to the last, one of the most novel and striking phenomena which met them everywhere was the great depth of decomposed or partially decayed rock in situ, which mantles, and for the most part conceals, the underlying strata. The same facts strike all geological observers from the North who happen to penetrate the middle and southern latitudes of the Atlantic States. In North Carolina, e. g., the entire middle and western regions, outside of the Quaternary clays, sands, and gravels of the East,—that is, all that portion of the State occupied by the Archæan and Mesozoic rocks,—show everywhere this peculiarity, so new to those accustomed to glaciated surfaces. Not only do the hills and slopes, the mountain chains and

Jan 1, 1880

By Bertrand L. Johnson

Barite, the natural sulfate of barium (BaSO4), is the most important barium mineral. Normally it is white (opaque to translucent), but impurities sometimes render it yellow, gray, blue, brown, red, or black. Brown or red stains are commonly caused by iron oxide. Barite is unusually heavy (specific gravity, about 4.5); in fact, it is one of the heaviest of the nonmetallic minerals. It is brittle and fractures unevenly. The hardness of barite ranges from 2.5 to 3 but is usually about 3. It can be scratched by a copper coin. Pure barite contains 65.7 percent BaO and A.3 percent S03. Much of the crude barite ore mined, however, contains impurities; thus it has a lower content of barite and consequently less barium oxide. Commercial analyses show its total BaSO4 content. Barium also occurs in nature as the mineral witherite (BaCO3), which, however, is not common in the United States, and commercial deposits have been found only in California. Witherite is a yellowish-white, light-gray, or Kite mineral with a specific gravity of about 3, a hardness of 3 to 4, and an uneven to subconchoidal fracture.

Jan 1, 1941

By J. M. Paxton, R. L. Roscoe, G. A. McCreary, W. W. Muir, T. J. Drown, D. A. Barr, T. W. Law

"This paper reviews the complete cycle of a small mining operation in a remote section of northern British Columbia, including discovery, exploration, development and production. The discovery of high-grade epithermal gold-silver mineralization occurred in 1969 following a regional geochemical reconnaissance program designed to search for porphyry copper mineralization in the Cassiar-Omineca Mountains. Exploration and development from 1971 to 1979 included geological, geochemical and geophysical surveys; trenching, almost 30 000 feet of surface and underground drilling in about 100 holes and cross-cutting, drifting and raising on the principal goldsilver- bearing vein. This led to the delineation of 100000 tons at an estimated grade of0.9 oz gold per ton and 18 oz silver per [on to an average depth of 120 feet below surface. of a 100-ton per day mining operation employing about 50 personnel with all supporting infrastructure transported to the site by a Hercules aircraft. The operation was subsequently supported by its own Twin Otter aircraft with periodic Hercules campaigns supplying major items including fuel.The mining operation included both open-pit and cut-and-fill methods. The milling operation employed conventional cyanide leach process with cyanide destruction initially by alkali chlorination and subsequently by the Inco SOl /Air process.The fly-in operation, initially structured on a 21-day-in and 7-day-out basis was modified to al-t-day-in and Z-day-out basis with no loss in efficiency and with a significant increase in employee satisfaction. The operation, which earned the B.C. Small Mines Safety A ward in two consecutive years in its Ll-month operating history, emphasized safety and process hazard awareness. Wildlife studies in the environmentally sensitive mine area also showed that industry and wildlife can coexist in harmony.Most importantly, the paper compares the feasibility assumptions with actual operating experience."

Jan 1, 1986

By T. D. Brown

"A review of the current status of gasification technology shows that many engineering systems are immediately available for use in the gasification of coal. Widespread international experience can be brought to bear on the atmospheric pressure gasification of all Canadian coals.Unless a high ash content dictates the use of a fluid-bed gasifier, it appears that bituminous coals can be used in gravitating (fixed] bed systems and that the strongly caking coals are most suited to the high-pressure entrained-bed systems . Existing and developing technologies in fluid-bed gasification are attractive for reactive lignites and subbituminous coals.The Fischer-Tropsch based process is the only commercial embodiment of coal liquefaction; the use of Canadian coals in this process depends only on their gasification characteristics. Current developments in hydroliquefaction are directed toward carboniferous coals of medium or high rank. It is not clear that cretaceous coals of the same rank will give similar process yields and economics.IntroductionThe twin coal conversion processes of gasification and liquefaction have a history which dates back beyond the current energy shortages of the western world. Indeed, liquids and gas from coal were produced before this century.Coal gas produced from a coal carbonization process was originated before 1800, and the development of gasification of non-coking coals was patented by Siemens in 1860.This patent represented the first use of air and steam together in the gasmaking process. The pioneering development of coal gasification Using oxygen and steam was demonstrated by Lurgi in the late 1920s. This historical sequence was all carried out at atmospheric pressure, and it was not until the immediate pre-war (1939/45) years that operation of the coal gasification process at elevated pressure became a reality."

Jan 1, 1981

By Simon E. Rodriguez

This paper presents sulfur isotope data obtained for the deposits and country rocks of the Bailadores and Aroa Mining District, Venezuela. The study is a part of an extensive geochemical investigation of the mineralized belts that has as their aim the elucidation of the genesis of ores. The Bailadores deposits are located at about 600 Km. west-southwest of Caracas, or about 10 Km. southeast of the Town of Bailadores, Merida State (Fig. 1). The mine concession is held by the Ministry of Mines and Hydrocarbons (De Lima I, De Lima II and La Cascade areas). In a straight distance the mine is about 90 Km. southwest of Merida, the capital of Mérida State. From Mérida to Bailadores, through La Victoria and Tovar, it takes 3 hour by car. From Bailadores to the mine site it is about 40 minutes by jeep. The Aroa deposits are located at 4 Km. east of Aroa Village, Yaracuy State, about 220 Km. west of Caracas. It is 83 Km. from San Felipe, the capital of Yaracuy State to the mine (Fig.2). The mine is about 600 m above sea level, situated on the northern foot of the E-W trending Andes. The topography of the mine are shows a mature stage and is somewhat rugged. As the climate is warm and humid, the area is thicky covered with jungle.

Jan 1, 1974

By Peter R. Drummond

THE final casting of refined copper has been re-J- stricted for generations by the following sequence of operations: Filling the reverberatory furnace, melting, skimming, blowing or flapping, and poling. The hoped-for 24 hr cycle, producing 300 tons or more, has been taken up largely with the necessary bat time-consuming tasks of cleaning the bath, sulphur elimination, and in turn removal of excess oxygen to produce tough-pitch copper. Incidental to comparatively slow melting under combustion gases, copper oxides react with the furnace lining, and the slag so-formed must be completely recycled. The three-phase arc furnace has eliminated some of the cycle stages, and telescoped the remainder into a continuous operation. Electrical energy, supplied to graphite electrodes enclosed in high grade refractories, rapidly melts copper cathodes and sustains a stream of metal, containing approximately 0.01 pct oxygen, without contamination from fuel. The arc was struck on the first large electric furnace for melting copper in the United States on April 13, 1949. The earliest use of this type of furnace was at Copper Cliff, Ont., in 1936, and an admirable description of their installation has been published? Copper, melted in the Baltimore furnace, is used to cast billets, and the installation differs somewhat from the Canadian, as will be described. The arc furnace is a heavy-duty, three-phase furnace, holding 50 tons, the general outline of which appears on Fig. 1. The steel shell is 15 ft ID with a bottom radius of 14 ft 2 in. The roof, separate and distinct from the body, consists of a 15-ft water-cooled, cast-steel ring of the same outside diameter as the furnace. The center line of the furnace lies 9 ft 6 in. from that of the trunnions, permitting a 5" backward tilt for skimming, and a 40" maximum nose tilt forward for complete draining. Normally, the furnace overflows by displacement, and the use of the forward tilt arrangement is restricted to covering charging delays. The charging slot, 3 ft 8 in. x 5 in., lies on the north center line, the tap hole on the south, and the 30x30 in. skim door 45" to the west of the slot. The original 20-in. graphite electrodes were replaced with 14 in. in December 1949. Three conventional direct current winch drives, governed by electrical controls, position each electrode which has individual mast supports and counterweights. An independent circulation supplies cooling water for the electrode glands, the roof ring, charge slot, and the skim door frame. Arc Furnace Refractories Hearth: Fused-in monolithic bottoms had been used in copper arc furnaces, installed prior to April 1949. These consisted of thin layers of periclase, successively fused in place over preliminary brick courses. Heat was obtained from the arc, using a T-like arrangement of broken electrodes resting directly on the periclase to be fused. The operation, taking weeks to perform, was very expensive. The chemically-bonded magnesite-brick bottom, installed at Baltimore, was the first of its kind and a radical departure from previous practice. It consists of a 1 to 6-in. layer of castable refractory laid on the steel shell, modifying it to a 12 ft 2 in. bottom radius. Two courses of 9x2 % -in. fireclay straights and keys follow. The third course is made of 9-in. magnesite blocks of special shape to form circles of an inverted arch. It was started by a four piece keystone with skew-backs forming the outer course. The fourth course also started on a central keystone, or button, of four 90" segments, 12 in. diam x 13 Vz in. deep, and continued with 13%-in. blocks. Skewbacks at the shell completed the course to produce a horizontal surface for the side walls with a single course of No. 2 arch fireclay against the steel. Dry chrome-magnesite cement was brushed over each course after laying, and a 1-in. expansion space between the brick and the shell was filled with the same mixture. The total bottom thickness, excluding the castable material, was 5 in. of clay plus 22% in. of chemically-bonded magnesite. Tap Hole: A 5-in. OD and 3-in. ID silicon-carbide tube constitutes the tap hole and is set tangential to the upper course of the furnace bottom. Molten metal fills the tube when the furnace is level and filled to capacity. Side Walls: The lining, against the shell, consists of a 9x4Y2x3 in. soldier course of fireclay, using straights and No. 1 arches to turn the circles. A second soldier course of 9x4'/2x2'/2-in. fireclay was laid in a somewhat similar fashion. Three courses of 13Y2x6x3 in. and 9x6~3 in. of final magnesite, laid flat, completed the lining, using Nos. 1 and 2 keys to turn the circles. Cardboard spacers were placed between every two bricks in horizontal courses, and a thin coat of chrome-magnesite cement filled the joints between the firebrick and magnesite. A sprung-arch spanned the skim door with jambs of suitable magnesite shapes. Charge Slot: The slot is 3 ft 8 in. wide x 5 in. high. A silicon-carbide sill of special shapes has a 30" slope to allow cathodes to slide easily into the bath. The original arch was flat, and composed of Nos. 1 and 2 wedge magnesite with a 6-ft radius. It projected 5 in. over the sill, and, being a flat arch, gave an 18 15/16-in. opening between the inner edge and the metal line. The whole assembly was later raised 9 in., and the flat arch replaced with an arch, the lower edge of which maintained the 5-in, width from the outer to inner edges as shown in Fig. 2. A water-cooled, cast-copper jacket protects the steel shell behind the slot.

Jan 1, 1952

By H. G. Oltmann

The equilibrium nitrogen solubility in the CaO-SiO2system was studied by a slag-gas equilibration technique, in graphite crucibles at 1823K under a CO-N2 atmosphere. The nitrogen content of the slags was determined by the Kjeldahl method. A reliable technique was used to obtain an initial nitrogen content in the master slags, from the addition and pre-melting of silicon nitride. Reduction of silica by graphite was found to occur during the equilibration experiments, resulting in compositional changes of the slags. The results were extrapolated to equilibrium by kinetic evaluation of the data. The nitrogen solubility showed good agreement with the result of Suito and Sano, while Fruehan?s results were lower. However, the results of the present study do not support the maximum nitrogen solubility values found by Sano.

Jan 1, 1999

By George M. Meisel

This paper is devoted to a discussion of the factors governing design of concentrators for large grinding circuits. Emphasis is placed on the manner in which use of ever larger grinding mills has affected the size of grinding bays, service cranes, gear reducers and electric motors, and the selection of ancillary equipment for cushioning of the starting load of large mills. Information is presented on the effect of using large grinding mills on the capital and operating costs of concentrators, e. g. : (Fig. 1) ? Benefits in lower cost of mills, drives and materials handling equipment, plant space, power, grinding media, operating labor and maintenance, and in ease of instrumentation and automation. ? Penalties in distribution of materials from the grinding mills to multiple lines of equipment which have not been developed to commensurately large sizes, and higher cost of ancillary equipment.

Jan 1, 1968

By W. J. Atkinson, E. M. Anderson

FOREWORD This paper is based on the authors' experience gained in the environmental assessment of major uranium projects in the former Department of Science and the Environment and Department of Home Affairs and Environment of the Australian Government. The authors gratefully acknowledge assistance received from colleagues within the Department of Home Affairs and Environment in the preparation of this paper. Special thanks go to Mr K.E. Thompson of the Department's Environment Division for his valuable comments and criticism. The views expressed in the paper are those of the authors alone and not the Australian Government or Dames & Moore. INTRODUCTION Uranium has been mined in Australia since 1954. A number of small scale mining and milling operations were active in the Northern Territory, in South Australia and in Queensland in the late fifties and early sixties. However, in the late sixties there was an increase in exploration activities in the expectation of an upsurge in world demand for uranium Substantial new resources were delineated in the Northern Territory, Queensland, South Australia and Western Australia. The most significant deposits were located in the Northern Territory, in what is called the Alligator Rivers Region located approximately 200 km east of Darwin. The Region is in the latitude of 13° South and thus lies within the Australian tropics (Figure 1). It consists of approximately 2.3 million hectares of natural wilderness containing much spectacular and attractive scenery. The area is noted for its abundant wildlife, particularly the waterbirds that gather on the flood-plains. Much of the vegetation is diverse and interesting. The Aboriginal population still maintains elements of the traditional way of life, and the spectacular Arnhem Land escarpment contains many of the best surviving examples of Aboriginal rock art. Numerous rich archaeological sites provide evidence of continuous human habitation for tens of thousands of years. Climatically, the Region is of the tropical monsoon type with a dry season from may to September and a "wet" from November to March. High intensity short period rainfall is characteristic, and the average annual precipitation is in the order of 1 350 mm. The monthly mean temperature ranges from 25° to 30°C throughout the year. The development of regulatory controls on uranium mining in the Alligator Rivers Region has been affected by the political status of the Northern Territory. While Australia is a federation, established as an independent self-governing country in 1901, it was not until 1978 that the Northern Territory became to any real extent self-governing. Prior to 1978, the Territory was administered through a special department of the Commonwealth (ie. the Federal Government). Under the Northern Territory (Self Government) Act 1978, administrative powers similar to those possessed by the Governments of the six founding Australian states were provided to the Territory Government. However, the Commonwealth government did not transfer to the Territory all such powers and functions, and in particular there has been, since 1978, a dual role for the Commonwealth and Territory Governments in the regulation of uranium development. Details of this role are provided later in this paper. RANGER URANIUM INQUIRY By 1973, major deposits had been discovered in the Alligator Rivers Region at Nabarlek, Ranger, Koongarra and Jabiluka. The estimated reserves and mine life expectancy of these deposits are given in Table I. Other radioactive anomalies have also been identified in the area but, as yet, they have not been delineated or evaluated. [ ] In 1974, an agreement was signed between the Commonwealth Government and Peko Mines Limited and the Electrolytic Zinc Company of Australia Limited for the joint development of the Ranger deposit. In July 1975, the Government announced a Commission of Inquiry under the provisions of the Commonwealth Environment Protection (Impact of Proposals) Act 1974, into the proposed Ranger development. The inquiry was known as the Ranger Uranium Environmental Inquiry or more commonly, the Fox Inquiry after the presiding Commissioner, Mr Justice Fox.

Jan 1, 1981