Search Documents

Mine planners must select a single pit for design with the knowledge that the grades on which this selection is made are uncertain. This uncertainty is often ignored through the use of deterministic models of grade. This makes the mine planner?s job simpler but does not necessarily lead to the ?correct? or ?best? selection. Grade uncertainty is typically modelled with conditional simulation which generates multiple possible realisations of grade that are equally probable (or improbable) to occur. Methods for incorporating grade uncertainty into mine planning to date have either been perceived as being too complicated, not accessible or too time consuming. This paper proposes a simple and efficient modelling approach to incorporating conditional simulation into pit optimisation, which would be able to be applied in currently commercially software. An example for Resolute Mining Ltd?s Syama Gold Project in Mali shows the range of ore, grade and value outcomes associated with generating pits through a variety of methods.

Feb 27, 2013

By W. E. Lamont

Flotation studies of phosphate-bearing waste pond materials, low-grade washer products, and raw ores, all from the Tennessee brown phosphate district, showed that these types of materials could be treated without des liming to recover high-grade phosphate concentrates. The investigation showed that fine grinding before flotation was a requisite for increased recovery of the phosphate values and that the optimum pH conditions were in the range of 10.0 to 10.5 when using anionic collectors. Multiple-cleaning of the rougher phosphate concentrate was required to produce high-grade concentrates. Phosphate recoveries ranged from 60 to 82 percent and were inversely related to the grade of concentrate produced.

Jan 1, 1972

By Jean Cayouette, Paul Blatter, Paul Cousin

"The Laronde mill was commissioned in 1988 and has been treating the Laronde Penna ore since 2000. The Laronde plant, situated in the Abitibi region of Quebec, has experienced mill expansions to accommodate 7500 mtpd and to recover gold and silver as well as important amounts of base metals (Cu, Zn, Pb). Ten sequential metallurgical and environmental processes are responsible for metals recovery and process viability. Over 200,000 ounces of gold, 4,5 million ounces of silver, 7000 tonnes of copper, and 78,000 tonnes of zinc are produced annually.In 2008, the Goldex plant began trucking high grade (35-45 g/t Au) pyrite sulphide concentrate (TCGO) for gold extraction at a newly constructed treatment plant, increasing gold output at Laronde by 40,000 ounces. In 2009, the high gold grade Lapa ore processing facilities were annexed to the Laronde plant increasing output by 120,000 ounces of gold. TCGO and Lapa productions are forecasted until 2018 and 2015 respectively, with known reserves of each mine.Today, up to 140 permanent employees run and optimise the Laronde plant operation. As a result, Laronde has intricacies intrinsic to a large and varied operation. The paper will outline the metallurgical highlights, challenges, and future outlook related to the treatment of each ore type (Laronde, TCGO, and Lapa).INTRODUCTIONFollowing the 2000 to 2003 expansions, the Laronde plant evolved into a mature milling complex with developed processing, man power, and water treatment capabilities able to accommodate the complex Laronde ore. The ore requires a series of grinding, copper/lead flotation and separation, zinc flotation, zinc tails precious metals leaching, followed by a counter-current decantation circuit and Merrill Crowe precipitation. A paste backfill and SO2-air cyanide destruction operate intermittently. The tailings area has a dedicated cyanide destruction and metals precipitation plant prior to water recycling to the mill. A biological water treatment plant was put into service in 2004 to address the build-up of thiocyanate in the tailings ponds at Laronde. This was the result of the high sulphide content of the Laronde ore and 90% recirculation of the process water. The plant uses bacteria to oxidize and destroy thiocyanate, and removes phosphate from the water before it is released to the environment."

Jan 1, 2011

By T. Fliß

The protection of natural resources is of essential importance in times of rapidly increasing populations and resulting shortage of agricultural land. Soil and groundwater resources play a central role for the production of food or feed of any kind. The intensive agricultural and environmentally friendly use of these resources must ensure sufficient income and sustainability of life for future generations. Mining projects often represent a particularly deep intervention into ecosystems due to their size as well as the most expensive treatment processes. Conventional mines comprising of shafts and developed mining fields require the stockpiling of waste rock and in particular to potash mining, the discharge of brines from raw salt processing. In contrast, mining operations based on the solution mining method can be operated without major environmental impacts and lower security risks. While the solution mining for the production of rock salt finds application since more than 500 years, exist a procedure to produce potash using solution mining only since the 1980's. For solution mining drill holes are used to exploit the potash, launched from the surface into the deposit. The exploitation of the raw material occurs by the dissolution of the potash injecting solvents and creating so-called brine caverns. Currently, a number of mining projects in Carnallite deposits by the solution mining method are in progress around the world. Often these projects are located in sensitive ecosystems. K-UTEC project and support actual a solution mining operation of a Carnallite deposit for a Chinese customer in South-East Asia. This work comprises a comprehensive geological and geomechanical modeling as well as stability analyses. Furthermore the cavern design and brine field layout as well as the planning of the brine processing and the plant design. The present paper introduces this project as a case study. The application of a special solution mining procedure and processing design ensures an emission-free mining operation (Zero Disposal Plant). The emission-free operation is achieved by utilizing the full extent of the caverns to dispose the liquid solutions from processing. The presentation of principal salt processing and technical equipment will be rounded by information about the geology of the deposit. Since the deposit includes a number of sensitive minerals, such as Tachyhydrite and Bischofite the presentation comprise a lot of interesting items with special view at the brine field operation. K-UTEC designed and delivered a special blanket measuring system and a well cement according the request of the customer. K-UTEC, a research and engineering company with more than 60 years of experience in the sector of potash and rock salt mining, developed the world's first solution mining operation for Carnallite in Germany more than 30 years ago. In recent times K-UTEC served in different solution mining projects worldwide, with special view at the environmental impact, as well as the optimal utilization of the deposits.

Aug 1, 2013

By D. W. Frommer

The investigation reported in this paper is one of several included in a broad program of developing new or improved concentration processes for the oxidized and partly oxidized deposits of lead and zinc, A sample from the Playter lease, Newton County, Mo., containing pyromorphite was successfully concentrated by fatty acid flotation to a grade of over 62 percent lead. Owing to the presence of a high content of slime-size values, the overall recovery of lead at that grade was limited to 44 percent. DESCRIPTION AND HISTORY OF PROPERTY The mineral pyromorphite is a chlorophosphate of lead containing 76.4 percent lead, and, although it occurs frequently in association with other lead minerals, it is considered a minor ore mineral of lead. The manner of occurrence of oxidized lead minerals, including pyromorphite, which frequently are no larger in grain size than the clay with which they are found, militates both against development of a simple beneficiation process and high recovery. The profitable exploitation of such deposits depends not only on a successful treatment procedure but a highly favorable metal market as well. For these, and perhaps other reasons, very little research has been done on the recovery of pyromorphite from its deposits.

Jan 1, 1956

By A. H. Marquis

Since the start-up of its first Direct Reduction Module in April 1973, S1DBEC has produced over 2 million tons of prereduced iron. During this period, SIDBEC has acquired comprehensive experience in the operation of the direct reduction process and at the same time has learned to recognize the characteristics that the oxide should have to constitute an adequate feed for the process. A comparison is made as to the design and operation of the two direct reduction units now operating at Contrecoeur, Que. A description is given of a method of evaluation of a direct reduction unit, which takes into account the main process variable sand which permits comparison ofthe results on a daily basis. The paper defines the characteristics that the iron oxide and the prereduced iron pellets must have to meet the specific requirements of the direct reduction and the electric arc furnace processes. A simple model makes possible a rapid evaluation of the technical and economic effect related to the use of a given raw material. Finally, the paper outlines the advantages of prereduced iron in the steelmaking process and on the quality of the steel products.

Jan 1, 1979

By Thomas M. Barczak

The decade of the 90's brought an unprecedented increase in the development of innovative technologies to provide more effective and easier to install roof support in underground mines. To facilitate the application of these technologies to improve mine safety. National Institute for Occupational Safety and Health (NIOSH) developed the Support Technology Optimization Program (STOP). STOP is a windows based software program that provides mine operators with a simple and practical tool to make engineering decisions regarding the selection and placement strategy of these various standing roof support technologies. This program includes a complete data base of the support characteristics and loading profiles obtained through safety performance testing of these supports at the NIOSH Safety Structures Testing Laboratory. Support design criteria in the form of the required support load density at a specified convergence can he established from four options: ( 1 ) a data base of measured ground reaction data from various mines or ground behavior information inputted by the user. (2) determination of loading requirements based on a detached roof block or rock failure height. or (3) criteria based on the current roof support system, and (4) arbitrary criteria set the by user. Using these design criteria, the program will determine the installation requirements for a particular support technology that will provide the necessary support load density and convergence control. Optimization routines are also available to determine the most efficient support design for a user specified support installation- In addition to these performance measures. STOP can be used to compare material handling requirements and installation costs. Comparisons among the various support technologies are easily made including graphical analysis of relevant support parameters. This paper describes the STOP and its application to optimize standing secondary roof support systems.

Jan 1, 2000

By Hans-Jürgen Schaller, Horst A. Brodowsky

Activity coefficients of boron in palladium were determined at concentrations up to PdB0.23 by reducing B2O3 between 870" and 1050°C in a controlled H2-H2stream and measuring the resulting weight gain. The deviations from ideal behavior closely resemble those of the system Pd-H and are interpreted in terms of three principles: 1) The solute atoms occupy octahedral interstitial positions. 2) They donate their valence electrons to the 4 d and 5s bands of palladium, raising its Fermi energy. 3) The lattice strain energy is lower for two nearesl -neighbor interstitial particles than for two farther separate ones. SOLID solutions of hydrogen in palladium are a useful subject for studying thermodynamic aspects of the formation of alloys and of nonstoichiometric systems.1-3 The activity of hydrogen is readily measurable to a high degree of accuracy,4'5 even at low temperatures where the deviations from ideal behavior are more pronounced, and its simple structure facilitates an interpretation of these deviations in terms of a detailed model. Two effects are discussed to account for the non-ideal properties:3 An "electronic" effect, connected with the rise of the Fermi energy, as electrons of the interstitial hydrogen atoms enter the electron gas of the metal, and an "elastic" effect, due to an interaction of the regions of strain around each interstitial atom. The electronic effect is based on the idea that the lowest energy levels of the dissolved hydrogen atoms are higher than the Fermi energy, so that the electron will not occupy a localized state but enter into the electron band of the metal.6 The elastic effect is based on the observation that dissolved hydrogen distorts and expands the palladium lattice. The hypothesis is put forward that the elastic strain energy is lower for two adjacent dilatational centers than for two separate ones; i.e., they attract each other. The resulting pair interaction can be used to calculate an elastic contribution to the thermodynamic excess functions by means of one of the statistical methods. This model permitted a detailed description of the solution properties of hydrogen in palladium3 and in palladium alloys.798 An extension of the approach to describe the excess functions of substitutional palladium alloys is possible.9 In order to further test and refine the model, an investigation of other interstitial alloys was started. Palladium dissolves considerable amounts of boron in homogeneous solid solution.10 The palladium lattice expands linearly up to nB = 0.23 (nB = B/Pd atomic ratio), the highest concentration studied." The expan- sion, extrapolated for 1 mole of interstitial per mole of palladium, is 17 pct of the lattice constant of pure palladium vs 5.7 pct in the case of hydrogen.12 The fact that the lattice expands rather than contracts is a strong indication that interstitial positions are occupied. According to neutron diffraction experiments, hydrogen occupies the octahedral sites of the fcc lattice.13 Unfortunately, this direct evidence is not available for the Pb-B system, mainly because of the high-reaction cross section of boron with thermal neutrons. However, by way of analogy and on the grounds of the rather close similarities between the two systems to be reported here, it seems safe to attribute octahedral positions to the dissolved boron, too. At higher boron contents, compounds of stoichiomet-ric compositions are reported such as Pd3B, which has the structure of cementite,14 so that a close structural relationship seems to exist with the system r Fe-C. In their study of hydrogen absorption in Pb-B alloys, Sieverts and Briining noted that alloys with an atomic ratio of about nB = 0.16 are no longer homogeneous15 This observation was confirmed in an extensive X-ray investigation.11,16 The phase boundaries of two miscibility gaps were established. One two-phase region was stable below a transition temperature of about 315°C and extended from nB = 0.015 to 0.178. The other one extended from nB = 0.021 to 0.114 slightly above the transition temperature and had an apex at nB = 0.065 and 410°C. All phases involved have the fcc structure of pure palladium with lattice expansions proportional to their boron contents. The occurrence of miscibility gaps, i.e., the coexistence of dilute and concentrated phases, points to an energy of attraction between the dissolved particles, in the Pb-B system as well as in the Pd-H system. The filling up of the electron bands seems to be analogous, too, in the two systems, as indicated by the hydrogen absorption capacit15,17,18 and by the suscepti bility of Pd-B alloys.l8 In both types of experiments, boron acts as an electron donor. A chemical method was used to measure the activity of boron in palladium. Boron trioxide was reduced in a moist hydrogen stream: B2O3 + 3H2 = 2B + 3H3O [l] At known activities or partial pressures of boron trioxide, hydrogen, and water, the activity of boron could be calculated from the law of mass action. The equilibrium concentration of boron corresponding to this activity was determined as the weight gain of the sample. EXPERIMENTAL The samples consisted of small pieces of foil of 0.1 mm thickness and about 100 mg weight. The palladium was supplied by DEGUSSA, Germany, and stated to be

Jan 1, 1970

By Mariana Macedo de Oliveira Lima, Pedro Emílio Gazola, Andrei Locatelli

Boron steel is used in the industry due to its great wear and impact resistance. During the hot rolling production of 15B29 steel flat bars it is a recurrent problem that the bars will present warping while on the cooling bed. Control this phenomenon is an opportunity to have better productivity, preventing metallic losses. Through the observation of the macro and microstructure samples produced with different reheating temperatures and cooling rates, it was found the presence of residual stresses and cracks on warped bars macrostructure. The residual stresses appearance suggest that the material cooling is too fast. Billets temperature on the reheating furnace of 1230°C reduced to 1100°C and the production pace slowed down. Bars temperature when arriving the cooling bed was reduced from higher than 670°C to 625°C. The results obtained made it possible to produce the material with better quality, reducing the warping effect at the cooling bed. The major influence on the materials warping was identified as the cooling rate at the cooling bed and the reheating furnace temperature was adjusted to provide a homogeneous temperature along the bars.

Oct 1, 2019

By Dick T. Atkinson

Due to improvements in the safety of other aspects of mining (primarily in roof control), haulage related accidents, particularly rail haulage accidents, are about to become the most common category of hazards causing death and injuries to underground coal miners. The major causes of these accidents are collisions between vehicles, men caught between rib and trip or between cars, derailments, and runaway cars. Such hazards can be greatly reduced if the motorman has the capability to selectively couple and uncouple cars from the cab of the locomotive, to transmit braking intelligence to the coupled cars, to determine if the trip is intact, and if brakes are automatically applied in any uncoupled car. These capabilities can be provided through an improved coupler system, designed and built by Foster-Miller Associates under a Bureau of Mines contract. Early in the program, a survey of rail haulage patents and literature was conducted. Manufacturers of couplers, mine cars and braking systems were contacted and information relevant to the remote control mine haulage application was collected. From this information evolved a working specification and a design concept. The key elements of the specification, shown in Table I, are the result of a detailed tradeoff study and considerable thought given to the specific problems encountered in the mining environment. A brief explanation of each element is as follows: Automatic Coupling - The couplers operate similarly with most already in underground use - they latch together when a trip is backed into a car intended for coupling. Remote Uncoupling - From the locomotive, the motorman can decide how many cars are to be uncoupled, operate the appropriate controls, and the desired coupler is opened.

Jan 1, 1977

By Marina de Menezes Lopes

Sabe-se que a presença de ultrafinos em plantas de beneficiamento de minérios pode comprometer a eficiência dos processos principalmente os de flotação, uma vez que fenômenos como o slime coating e o arraste hidrodinâmico das partículas ocorrem fortemente. Além disso, concentrados contendo uma proporção significativa de ultrafinos terão dificuldade de serem filtrados gerando tortas de alta umidade. Este trabalho teve por objetivo estudar o efeito do dispersante AGLP consumido atualmente na planta de beneficiamento da Votorantim Metais Vazante, na flotação do minério silicatado de zinco e avaliar o efeito da sua dosagem na umidade do concentrado final produzido. Para tanto foi realizada a caracterização granulométrica das amostras e conduzidos testes de bancada de sedimentação, filtração e flotação em diferentes dosagens de AGLP. Como era de se esperar, os resultados identificaram que o concentrado de granulometria mais grosseira obteve melhor sedimentação e umidade. Já os testes de flotação indicaram que a dosagem ótima do dispersante em torno de 400g/t garante um concentrado de qualidade, sem perda de recuperação metalúrgica e com umidade adequada para que seja transportado.

Aug 17, 2017

By Joseph Renk, David Akers, Glenn Shirey

Each year, US coal cleaning plants landfill or impound millions of tons of high-quality, fine-sized coal. This coal is not only difficult and expensive to capture during cleaning, but, if captured, can pose serious materials handling problems. The GranuFlow. Technology was developed and patented by the U.S. Department of Energy (DOE) to address these problems. GranuFlow involves the addition of a coal binding agent such as an asphalt or heavy oil emulsion to coal to reduce moisture, dusting, and freezing and to improve the flow properties of the coal in bins and chutes (1, 2, and 3). When the emulsion is added before mechanical dewatering, the binding agent causes the formation of fine-sized coal agglomerates that dewater better than untreated coal. In addition, the binding agent increases the capture of ultra-fine coal in screen-bowl centrifuges. Previous work by DOE has also demonstrated that such treatment results in a significant reduction in dustiness and a reduced potential to freeze. To address concerns about the handling and combustion characteristics of GranuFlow treated coal, DOE performed a pilot-scale pulverization and combustion test (4). No problems were encountered during pulverization or combustion, and use of this fuel in a p.c. boiler was found to be feasible from a technical perspective. CQ Inc. has an exclusive license from DOE to market this technology and is currently performing a series of commercial demonstrations to determine if GranuFlow is both technically and economically viable.

Jan 1, 2005

By Timm Schoening, Greinert. Jens, Iason –. Zois Gazis

"Ferromanganese nodules are again of interest because of their high concentrations of Ni, Co, Cu as well as REE. With regards to an operational underwater mining industry, one of the main questions and important requests is to finding a method that can predict the abundance of nodules with high accuracy within reasonable time spans, without many requirements for ground truth data; and all these on an operational scale and ideally automated. In this regard, we present results of a study based on the combination of highresolution multibeam and optical data acquired by an AUV using specific machine learning techniques to reveal a detailed distribution of the Mn-nodules in correlation to the seafloor terrain. The accuracy of the method employed and results gained were validated and approved through comprehensive statistical analysis and by comparison to box-core data.Study AreaOur study area (AUV survey block G77) is located in the Clarion-Clipperton Zone (CCZ) (Eastern Central Pacific Ocean), an area that has been receiving international research and industrial attention for many years already (e.g. McKelvey et al., 1979; Bernhard and Blissenbach, 1988, von Stackelberg and Beiersdorf, 1991, Jeong et al. 1996). Block G77 covers an area of 9.5km2 in a depth between -4478m and -4536m. The area is characterised by gentle slopes 0-5° (0-3° in most of the area and only in the outer parts of the Block slopes can exceed 5°). The seafloor is characterised by moderate to low rugosity, the only exception being a small area in the eastern part, where sub-recent smallscale volcanic activity created 15 cone-shaped morphological features of up to 55m height and 150m width that are clustered in an area of 700 x 380m (Figure 1)."

Jan 1, 2017

1. In 2002, a total of 2,065 coal mining operations reported employment to the Mine Safety and Health Administration (MSHA). Coal mines comprised 14.2% of all mining operations. • Bituminous mines comprised 92.5% (n = 1,910) and anthracite mines 7.5% (n = 155) of coal mining operations. • More than 70% of all coal mines were located in three states: Kentucky (28.7%), West Virginia (21.7%), and Pennsylvania (20.1%).

Jan 1, 2004

By V. J. Sopuck, O. P. Lavin, Ian Nichol

"A major challenge of contemporary exploration geochemistry is the development of procedures that can locate blind mineralization or mineralization that sub-crops below a cover of transported overburden, the composition of which bears no relation to the underlying mineralization. Over the past few years, the possible existence of diagnostic geochemical features in the country rock associated with volcanogenic massive sulphide deposits has attracted increasing attention both on the local mine scale and on the regional scale. In the present investigation, the nature of the geochemistry of a number of Archean greenstone belts of the Canadian Shield is examined to determine the feasibility of distinguishing productive from non-productive areas of copper-zinc mineralization. The results indicate that productive areas are distinguishable from non-productive areas providing consideration is given to the effects of igneous differentiation on rock compositionIntroductionArchean massive sulphide deposits are an important source of copper and zinc, and to a lesser extent silver and gold, particularly in Canada. As in the case of most other forms of mineralization, there is a continual need to develop new techniques that will improve the chances of success in the search for these deposits. The majority of Archean areas in the northern latitudes are overlain by a variable cover of glacial overburden. Considerable progress has been made in the development of new geochemical exploration techniques for use in glaciated terrain, based on the detection of anomalous dispersion in the glacial overburden. In certain situations, however, as in the search for blind deposits or in areas covered by glaciolacustrine deposits, overburden geochemistry offers little hope for success. In the case of massive sulphide deposits, one possible solution may lie in the detection of anomalous geochemical signatures in the bedrock. Recognizing this possibility, attention has been directed to the investigation of the nature of lithogeochemical dispersion associated with massive sulphide deposits on both regional and local scales, to establish the potential of lithogeochemistry as an aid in the search for these deposits."

Jan 1, 1980

By L. Cheng

This report describes a laboratory investigation of the effectiveness of low-pressure steam and a steam-water spray sequence for the collection of airborne respirable (<10 µm) coal dust. Comparison of present results to previous results obtained with water spray alone indicates that the use of steam in a steam-spray sequence increases the collection efficiency by about 14 percent over that obtained by water spray alone. However, the use of steam to collect airborne dust requires cooling the steam-dust mixture in order to achieve condensation of the steam, and steam does not appear to be an attractive approach for collecting airborne dust in underground coal mining operations.

Jan 1, 1974

By Baisheng Nie

The process of gas diffusion through coal particles and the mathematical physical model under the third kind boundary condition was determined to obtain the rules of gas diffusion through coal particles of different sizes. The analytical solution of the equation was obtained by the Method of Mathematical Physics. The parameters of analytical solutions and the implications of parameters were analyzed. The Biot criterion (Bi) and the Fourier criterion (F0) of mass transfer can represent and reflect the features of gas diffusion field of coal particles. Moreover, the measurement method of gas diffusion coefficient and surface mass transfer coefficient is introduced and an example of measurement is given. The achievement can provide the support to prevent disasters related to methane in coal mines.

Aug 1, 2013

By John C. Machisak

DATA ON INJURY experience at quarries and related plants of the United States are presented in this publication under the following general sections: A) General injury experience: Tables 1-4: Contain current data on number of injuries, injury-frequency rates, work location, accident agency, degree of injury, and related employment data. (B) Injury experience at different kinds of quarries: Tables 5-6: Current data on number of injuries, injury-frequency rates, work location, accident agency, degree of injury, and related employment data. (C) Injury experience by States: Tables 7-19: Current data on the number of injuries, injury-frequency rates, accident agency, degree of injury, and related employment data. (D) Selected injury data: Tables 20-30: Current data on various selected factors of operating conditions at different kinds of quarries, including employment size-groups, length of shifts, comparative severity of injuries, and injury data and related employment experience at dimension-stone and crushed and broken stone quarries, and underground quarries. (E) Mining methods and historical injury experience: Tables 31-32; Employment data and injury experience in the quarrying industries of the United States, by mining method and work location, 1953-58; and historical injury experience and employment data in the quarrying industry, 1911-58.

Jan 1, 1962

By Don Phelps, Dean Brox, Peter Procter, Andy Saltis, Tom Morrison, Jeff Pringle

The Greater Vancouver Water District is currently constructing the Seymour-Capilano Water Filtration Project to enhance the quality of drinking water in the Vancouver metropolitan area. The Seymour-Capilano Water Filtration Project comprises the 1,800 million litres per day Seymour-Capilano Filtration Plant, the 1,080million litres per day Capilano Pumping Station, twin tunnels with associated shafts, and the Capilano Energy Recovery Facility. The twin tunnels will convey raw water under pressure from the Capilano Reservoir to the Seymour Filtration Plant and return treated (filtered) water for distribution. The Twin Tunnels component of the project comprises twin, 3.7 m diameter, 7.2 km TBM bored tunnels, the 180 m deep Seymour Shaft as the main launch shaft, and two 4 m diameter, 268 m deep raise bore exit shafts at Capilano. The Twin Tunnels have been planned as predominantly unlined tunnels sited at depth entirely within granitic bedrock and cross under two major buried glacial valleys of breadths in excess of 1500 metres that are filled with glacial sediments to depths up to 200 metres. The maximum overburden along the tunnel alignment is approximately 400 metres. Comprehensive site investigations and studies were completed during the detailed design stage of the project. The construction of the twin tunnels started in the fall of 2004 and is planned to be completed by mid-2008.

Jan 1, 2005

By J. E. Sepulveda, R. Morrow

"In full scale mineral grinding operations, the steel balls normally utilized as auxiliary grinding media get to be consumed at different specific rates, as determined by 3 basic mechanisms: abrasion/corrosion (wear), impact ball breakage and impact surface spalling, the latter relating to the removal of rather small pieces of steel coming off the exposed surface of the balls due to repetitive impact with other balls in the charge or the surrounding mill liners. In conventional ball milling applications, the clearly predominant mechanism is gradual wear by abrasion/corrosion. In the case of SAG mills, where the make-up balls may be as large as 6”f diameter, breakage and spalling mechanisms are significant contributors to total ball consumption, although not to the extent of overriding wear mechanisms.Ball wear has been well characterized by the Linear Wear Theory, as presented at the last CMP 2014. Impact breakage has been customarily monitored, at the ball manufacturing site, via Drop Ball Tests (DBT) consisting of repeatedly dropping balls from a standard height and accounting for the number of broken balls and the weight loss (spalling) of the remaining unbroken balls. When properly conducted, DBT’s should provide meaningful indications of the breakage and spalling resistance of large diameter balls. The current publication is focused on the interpretation and projection of DBT results to full industrial scale, taking into account all 3 mechanisms of grinding media consumption in SAG mills.INTRODUCTIONA thorough, quantitative understanding of the independent contribution of all active grinding media consumption mechanisms is of the highest practical relevance, particularly in semiautogenous (SAG) milling operations where ball breakage and spalling can not be ignored or neglected, as it has been normally acceptable for conventional ball milling processes. The high severity impact conditions currently imposed in typical SAG mill environments create serious challenges to the manufacturers and suppliers of large diameter (5”–6”) SAG balls, whose products must be capable of surviving such harsh operational conditions with minimum breakage or spalling."

Jan 1, 2015