Search Documents

By Almon F. Robertson

This is one of a series of reports describing investigations made within the Missouri River Basin in Montana by mining engineers of the Bureau of Mines, Minerals Division, Region II. The primary purpose of these investigations is to provide basic information to agencies of the Department of the Interior and other agencies concerned with the planning of power and other water developments in the Missouri River Basin. This report contains only such factual data as have been authorized for public distribution. Special precautions have been taken not to reveal any information or data considered to be confidential. The field investigations for this report were made during the fall of 1948 and the summer of 1949. Virtually all of the known metallic mineral deposits and some nonmetallic (industrial) mineral deposits within Judith Basin County were investigated. Most of the mines and prospects have been inactive for many years; most of the old underground mine workings now are inaccessible or only partly accessible. Consequently, much of the information on many of the mines and prospects necessarily has been obtained from available U. S. Government and State publications and from owners and local residents.

Jan 1, 1951

By Donald L. Stewart, Ken Overfield, Edward M. Williams

"Recent increases in energy cost have lead to a renewed focus on energy efficiency during aluminum melting operations to reduce fuel usage. The goals of a batch melting operation are to melt the charge using the minimum required energy, to melt the metal to the required temperature within the required timeframe, and to avoid generating unwanted contaminants by overheating the charge.The heat transfer efficiency of a conventional hydrocarbon fired aluminum melting furnace varies over the course of the melt cycle, depending on the conditions in the furnace. The purpose of this work was to develop a method of determining the transient heat transfer efficiency throughout the furnace cycle and to take advantage of this knowledge to optimize the melting process through furnace controls and proper production operations. This furnace survey methodology has been developed and used to evaluate a number of furnaces.Description of a Typical Batch Melting Furnace CycleA typical batch melting furnace cycle will consist of three stages:1. Charging – Solid metal charged through an open roof, solid or molten charged through an open door, and/or molten poured through a furnace blister2. Melting – From the time the door or roof is closed and the burners are turned to high fire until the charge is all liquid and has reached a temperature suitable for alloying (typically ~1350 °F / 730 °C)3. Holding – From the end of the melting stage until transfer or casting is completeIn some cases, further charging can take place after the melting cycle has started. This can happen when the entire solid charge will not fit in the furnace in one load, or if additional molten metal is added while the charge is melting. The bulk of the energy used in the melter is consumed during the melting cycle. The thermodynamic minimum energy requirements for melting pure aluminum are:• Energy required to heat pure aluminum from room temperature to the melting point at 1220°F (660°C) is 288 BTU/lb (670 kJ/kg)• Energy required to change state of pure aluminum from solid to liquid (heat of fusion) is 171 BTU/lb (397 kJ/kg)• Energy required to heat molten from melting point at 1220°F (660°C) to 1350°F (730°C) is 36 BTU/lb (83 kJ/kg)• Total energy required to melt a solid charge from room temperature to 1350°F (730°C ) is 495 BTU/lb (1151 kJ/kg)"

Jan 1, 2009

By L. E. Welch, C. W. MacGregor

THE past 20 years has seen a revolutionary change in the testing of materials at elevated temperatures. This has largely been brought about by the practical importance of the creep problem in the design of equipment for operation at high temperatures. The short-time tension test carried out at elevated temperatures has consequently assumed in many cases only a secondary role compared to the long-time creep test. In many problems, however, a knowledge of the short-time high-temperature properties of a metal is essential. To mention a few cases in which this is so, we might include all hot-forming operations such as rolling, forging, etc., the welding problem if residual stresses are to be computed, the development of new alloys for high-temperature service where, in the initial stages, time does not permit of long duration creep tests, and others. Usually a knowledge of the short-time properties is desired, if only to serve as a background against which to compare creep behavior. In conducting short-time high-temperature tests, it has been almost the universal practice to determine stresses based on the original area and strains referred to the original gauge length which is usually chosen as 2 in. It has been pointed out 1,2 that one of the reasons that the true significance of certain tensile properties is not understood, which perhaps curtails their usefulness, especially when the material is applied [ ] under conditions differing considerably from the test conditions, is that true physical stresses and strains are not determined. It is essential to have a knowledge of true stresses and strains in order to correlate the values present in the tension test with those existing, for example, in hot metal-forming operations and in the general problem of the yielding and failure of metals under combined stress conditions. Stress and strain values based on the original dimensions of the test piece do not exist physically except in the early stages of the test. Since at the present time there is very little information in the literature on true stress-strain relations in the short-time high-temperature tension test it is proposed in the following pages to describe a

Jan 1, 1942

By H. O. HOPMAN

(Canal Zone Meeting, November, 1910.) I. INTRODUCTION. THE substance of this paper was prepared for the Seventh International Congress of Applied Chemistry, held in London, May, 1909, under the title, Some Developments in Blast-Roasting. In the absence of the author, a -short abstract of the paper was read, and the abstract only will appear in the proceedings of the congress. The present paper has been partly rewritten and considerably enlarged by information gained since the original was prepared ; also some illustrations have been added. Blast-roasting' is a generic term for the process of forcing air through finely-divided. metallic sulphide with the object of roasting and agglomerating in a single operation. At first the process was confined to a galena-concentrate ; lime, limestone, or gypsum was added, to serve both as a diluent to keep separate the particles of galena that they might be thoroughly oxidized, and as a flux that the partly-roasted ore might be agglomerated by the formation of some slag. Later it was extended to treat other metallic sulphides. The leading processes were the Huntington-Heberlein and the Savelsberg of Europe, and the Carmichael-Bradford of Australia. In the United States and Canada, the Huntington-Heberlein process has found application in some instances with galena-concentrates, for which it was originally intended; but this class of ore is not often treated alone, hence the process has had to be modified to suit conditions. The Savelsberg process has been transplanted to this country in about its original form. The Carmichael-Bradford is not used at present. The changes called for in the Huntington-Heberlein process to adapt it to the class of lead-bearing ores usually smelted have been the 1 A. S. Dwight, Engineering and Mining Journal, vol. lxxxv., No. 13, p. 649 (Mar. 28, 1908).

Jun 1, 1910

By Oliver Q. Leone

The effect of oxygen content in the anode metal on titanium electrorefining characteristics was studied. Increasing quantities of oxygen in the anode resulted in increased anode scale formation, decreased anode and cathode current efficiencies, lower titanium recovery efficiencies, and higher oxygen content of the cathode products. The titanium electrorefining process performed best when the anodes did not contain more than 0.5 percent oxygen, although anode dissolution was recorded for alloys containing up to 25 percent oxygen. Back emf affords a useful index of an alloy to electrorefining.

Jan 1, 1965

By L. Li

To accommodate the large payloads and harsh operating conditions associated with heavy vehicles in the mining industry, off-the-road (OTR) tires are typically used with heavy mining vehicles. These tires have increased abrasion and wear resistance due to their thicker tread, sidewall and bead thicknesses. Given these features, OTR tires are much stiffer than conventional passenger vehicle tires and cannot be mounted to a single-piece rim without damaging the structural integrity of the tire during the mounting process. Therefore, multi-piece wheels are used with OTR tires to facilitate mounting. While these assemblies are necessary, several instances of their failure have been reported to result in injuries or fatalities within the mining workplace. Many of these failures were specifically reported to be caused by the disengagement of the wheel lock ring - a component used to securely engage the assembly during operation. In this study, a threaded-connection locking mechanism has been proposed in place of the traditional lock ring design. The performance of this threaded-connection was numerically evaluated in a pull-out test against a conventional five-piece wheel assembly. The pull-out test was devised as a means of quantifying the engagement ability of each wheel?s locking mechanism. A high degree of modelling accuracy was maintained throughout the analysis by validating the vertical and horizontal static loaddeflection behaviour of the rim model of the five-piece wheel assembly against experimental data. Through validation, the model data were found to be within 10.5 and 4.80 %, for vertical and lateral loaddeflection behaviour, respectively. Results from the pull-out analysis found that the threaded-connection demonstrated a 113 % increase in the force required for disengagement to occur relative to the conventional five-piece design - a force of 9,550 kN in total.

Aug 1, 2013

By Atmesh K. Sinha

The demand for thermal coal both nationally and internationally is projected to increase rapidly. The marketability of high ETU thermal coal produced in the USA is, however, limited by its high sulfur content. Fortunately, over 70 percent of the sulfur exists in pyritic form. The research conducted at Southern Illinois University indicates that over 90 percent of the pyrite can be removed by simple devices such as concentrating tables, cyclones, or froth flotation cells and the desulfurized coal can be blended with low sulfur western coal to produce EPA compliance coal. Thus, both the low BTU western coal and the high sulfur midwestern coal can be rendered competitive in the utility markets, here and abroad due to improved utilization.

Jan 1, 1983

By Mohamed Mekkawy, William W. Wheaton, Ira Brotman

"The Virginia Port Authority and the U.S. Army Corps of Engineers are partnering to construct the Craney Island Eastward Expansion (CIEE) to meet the dual purpose of extending the life of Craney Island as a dredged material management area and providing land for a state-of-the-art marine terminal. The over 500-acre (200-hectare) expansion provides additional upland dredged material capacity for the Hampton Roads Harbor by constructing perimeter dikes, that once filled, will provide land for the development of a container terminal. In the winter of 2010/2011 the first stage of sand fill was placed, followed by the installation of approximately 12 million linear feet (MLF) (3.6 million linear meters, MLM) of marine PVDs. With over 36 MLF (10.9 MLM) of PVD required to complete dike construction the project will be one of the largest PVD installation project in the U.S.This paper details the challenges associated with the construction of the cross dikes, in particular the design, testing, installation and monitoring of prefabricated vertical drains (PVDs) installed overwater to depths of over 130 feet (40 meters) for foundation improvement in the insitu very soft Norfolk Clay. With expected settlements of 20–30 ft (7-10 m) and 30 percent average strains, the discharge capacity of the PVDs was of particular concern. Laboratory data is presented showing the magnitudes and variability of discharge capacity under different confining pressures in both a straight and buckled condition.The method of installation and monitoring of the marine PVDs in open water included developing a specialized barge and sophisticated positioning and data collection system to verify installation location, depth of penetration and track quantities. An observational method, including material testing, detailed surveys, periodic in-situ testing, and instrumentation, was utilized by the project team to assess the project’s progress and allow for validation of consolidation and strength gain rates and magnitudes."

Jan 1, 2017

By D J. Bradshaw, E M. Wightman, C L. Evans, B Triffett

During the commissioning phase of Prominent Hill, periods of reduced recovery were experienced with higher-grade ore blends. This was unexpected and as part of the process to identify the cause, surveys were conducted in May 2009, with two different ore blends (copper grades: 1.94 per cent Cu (blend 1) and 2.49 per cent Cu (blend 2)). Metallurgical performance was assessed in terms of rougher recovery and grade with consideration of both pulp and froth effects. In addition, hydrodynamic measurements (gas hold up, bubble size, superficial gas velocity) as well as measurements of bubble load and top-of-froth grade were taken during the surveys and full mineralogical assessment of selected streams completed to characterise the nature of the differences. The metallurgical results showed that the lower performance was obtained with blend 2 which contained the higher amount of chalcocite and was higher-grade. Analysis of the survey data showed that for both ore blends more than half of the copper loss occurred in the +38 ¦m size fractions. Almost 30 per cent of the copper in the +38 ¦m fractions that reported to the rougher tails during processing of blend 2 was liberated compared to less than five per cent for blend 1. Additionally almost 60 per cent of the copper in the +38 ¦m fraction of blend 2 was chalcocite compared with approximately 20 per cent in blend 1. This paper discusses the sensitivity of the chalcocite-to-surface chemistry effects causing marked reductions in recovery either through reduced pulp recovery or froth phase (detachment) effects. The reagent suite and operating conditions were subsequently changed and the recoveries increased substantially and the sensitivity to ore changes eliminated. It should be noted that subsequent optimisation work, which focused on recovery improvement, has led to copper recoveries of over 90 per cent being achieved.CITATION:Bradshaw, D J, Wightman, E M, Evans, C L and Triffett, B, 2012. Characterising the reasons for the difference in performance of two ore blends in early processing at OZ Minerals Prominent Hill Operation, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 273-278 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By F. Dinter, C. McGregor, Q. G. Reynolds, L. Hockaday

The necessity of reducing greenhouse gas emissions to limit the impact of anthropogenic climate change means that all industrial processes should investigate their options towards decarbonization. Iron, steelmaking, aluminium, and cement production produce the most industrial emissions. Although most research focuses on decarbonizing these industries, minerals processing industries must be decarbonized to achieve net zero emissions goals by 2050. Incorporating renewable energy sources and avoiding the combustion of fossil fuels are two ways to reduce greenhouse gas emissions. This paper reports on the results from a dynamic process model developed to investigate the feasibility of concentrating solar thermal pretreatment of manganese ores to pretreat carbonate-rich manganese ores for increased ferromanganese smelter productivity and reduced greenhouse gas emissions. The results indicate that pretreated ores reduce the energy requirement for smelting significantly for some ores and lowers total carbon dioxide emissions by 13 to 19% compared to the traditional smelting route. A high-level economic evaluation shows that solar thermal treatment is financially viable for low cryptomelane, high braunite ore that is common in the Kalahari Manganese Field.

Dec 11, 2024

By B. W. Gandrud, G. T. Bator

The recent introduction of small coal jigs in Alabama to meet the needs of truck - mine operators for cheap and economical cleaning equipment marks another step in Alabama's pioneering record in the mechanical cleaning and preparation of coal . During the past 4 or 5 years a number of these small jigs , with capacity of 5 to 10 tons per hour , have been installed at Alabama truck mines and at a few truck mines in Illinois , Tennessee , and Pennsylvania . Most of the installations have been at mines that specialize in the production of domestic , stoker coal . This report describes three models of small jigs and includes performance data obtained recently on one of the models by the Bureau of Mines, United States Department of the Interior , in cooperation with the University of Alabama, Tuscaloosa , Ala . , for the purpose of comparing it with fullsize jigs on a performance basis . With literally hundreds of truck mines now in operation throughout the country , it has been assumed in preparing this report that there is widespread interest in the availability of small - scale inexpensive preparation equipment for use at such mines in the production of steam and domestic coal and in some instances coal for manufacture of coke . Practically none of the coal from Alabama truck mines is scld to coke - oven plants ; but in some sections of the country truck mines supply a considerable amount of coking coal, and the use of small, inexpensive washers at some of them might be very advantageous during the present war emergency from the standpoint of increasing pig - iron production through improvements in coke quality .

Aug 1, 1943

By D Tuazon, M Powell, M Ziemski, G D. Corder

Although mining companies have made broad corporate-level commitments to adopt sustainability, there continue to be problems when attempts are made to adopt higher-level sustainability aspirations and translate them into appropriate targets and methods at the more-specific operational level. The integration of sustainability principles into minerals processing operational decision-making processes has unique challenges that are not addressed adequately by current tools and methodologies, yet impacts from operational decisions can have longer-term effects realised at closure and rehabilitation.This paper describes a proposed methodology to achieve the integration of sustainability at the operational level through a systematic and rigorous process of identifying and qualifying sustainability issues and opportunities in an operation. The methodology, starting from a sustainability point of view rather than an operational one, guides the identification of process issues and opportunities by examining the operation, unit-by-unit, similar to a Hazard and Operability (HAZOP) process. Each issue or opportunity is qualified according to its measurability, scopes of impact and consequences so that it may be understood fully and the correct engineering problems are formed. Through improved decision-making to account for broader sustainability factors, operations can better address environmental and social expectations and pressures (both corporate and community, as well as immediate and in the longer-term), whilst still delivering on operational and business goals.The methodology has been tested with two case studies at minerals processing operations. At one site, the methodology identified a dust issue which had considerable business risks (loss of valuable product) compared to conventional engineering analysis processes. The other site also benefited from using the methodology as an opportunity to improve the operation of the milling and flotation circuits was identified. The opportunity not only showed a potential to improve operational efficiency, but also potential improvements in water and energy efficiency and a resulting increased resilience against water and energy supply risks. It was important to utilise the holistic approach of the methodology in the identification of opportunities at this site; the goals of the operation showed a strong coupling between water and energy issues which would be difficult to overcome using the operationÆs current organisational model, which deals with such issues separately of each other.CITATION:Tuazon, D, Corder, G D, Powell, M and Ziemski, M, 2012. A practical and rigorous approach for integrating sustainability principles into decision-making processes at minerals processing operations, in Proceedings Life-of-Mine 2012 , pp 233-242 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By A. L. Mackie

Arsenic is a highly toxic element and a known human carcinogen. It is often a contaminant in mine water discharges, particularly from gold mining and roasting operations, and has been found at concentrations as high as 4 g/L. Increasingly stringent controls on the concentration of arsenic allowed to be discharged into the environment cannot always be met by current treatment processes and thus enhanced technologies are required to achieve low treated effluent concentrations at reasonable costs. A novel two-step physicochemical treatment process was developed and tested at the bench-scale using synthetic mine water solutions (SMWs) in order to reduce arsenic concentrations in treated effluent to exceed current discharge regulations. The process includes chemical coagulation with ferric sulphate and ballasted flocculation for enhanced solid-liquid separation. The SMW contained 59 ± 2 mg/L arsenic with a slightly alkaline pH. The effect of arsenic speciation on the process was tested by using either arsenite, As(III), or arsenate, As(V), in the SMW solutions. Tests were performed at cold temperature (3 ± 1 °C) to ensure the process? efficacy year-round in northern climates. Arsenic in As(V) SMW solutions was removed to a final total concentration of 0.0054 ± 0.002 mg/L, almost half the current recommended allowable drinking water concentration of 0.010 mg/L. As(III) was removed to a concentration below the Metal Mining Effluent Regulations? (MMER) current limit of 0.50 mg/L, to 0.32 ± 0.06 mg/L, with double the coagulant dose used in Stage 1 for As(V) removal. Oxidant addition at a concentration of 5 mg KMnO4/L in Stage 2 resulted in final total arsenic concentrations of 0.017 ± 0.002 mg/L and pH adjustment with lime in Stage 2 resulted in 0.0415 ± 0.0007 mg As/L in treated As(III) SMW. Both of these modifications to the process reduced arsenic concentrations to below proposed new MMER limits (i.e., 0.10 mg/L). This two-stage treatment process was shown to reduce arsenic concentrations to well below current treatment guidelines while reducing or eliminating chemical oxidant demand.

Aug 1, 2013

By Lysle E. Shaffer

TEACHING engineering students how to write and speak effectively -is one of the greatest problems facing the technical schools today. No phase of engineering education has received more criticism, and rightly so, for the criticism is justified. Year after year we continue to graduate men that are indifferent to the use of a tool they will need every day of their lives. Our young engineers cannot write a clear, concise report, and their business letters are a disgrace to the profession that takes pride in precision. The problem is not new. The remark ascribed to Sir James Barrie, that "The man of science appears to be the only man who has something to say, just now-and the only man who does not know how to say it" is as uncomfortably true today as it was thirty years ago. The records of meetings of engineering educators and the transactions of the engineering societies show that the inability of the engineer to communicate his ideas has been discussed for years. Engineering educators, prodded by industry, have recognized that the problem exists, but they have not solved it. Instead they continue to expose the student to composition and rhetoric, hustle him through English and American literature, and then blame his high school because he does not know enough English grammar to write a clear sentence. We must face the fact that the graduate is not going to reflect on the high school, but on his college. If the high school has shirked the job, the responsibility for correction rests on the faculty of the professional school.

Jan 1, 1948

By F Minz, P Lamberg, A Mwanga, C Lund, C Wanhainen, M Amiri Parian, J Rosenkranz

A geometallurgical model is currently built in two different ways. The first and the most common way relies on geometallurgical testing, where a large number of samples are analysed for metallurgical response using small-scale laboratory tests, eg Davis tube testing. The second, mineralogical approach focuses on collecting mineralogical information over the orebody and building the metallurgical model based on mineralogy. At Lules University of Technology, Sweden, the latter method has been adopted and taken further in four ongoing PhD studies. The geological model gives modal composition by the help of element-to-mineral conversion and Rietveld X-ray diffraction. Texturally, the orebody is divided into different archetypes, and liberation measurements for each of them are carried out in processing fineness using IncaMineral, a SEM-based technique. The grindability and liberation spectrum of any given geological unit (sample, ore block, domain) are extrapolated from the archetypes. The process model is taken into a liberation level by mass balancing selected metallurgical tests using the particle tracking technique. The approach is general and can be applied to any type of ores. Examples of ongoing studies on iron and massive sulfide ores are given.CITATION:Lamberg, P, Rosenkranz, J, Wanhainen, C, Lund, C, Minz, F, Mwanga, A and Amiri Parian, M, 2013. Building a geometallurgical model in iron ores using a mineralogical approach with liberation data, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 317-324 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By W. N. Cathey

Many materials including carbides, silicides, phosphides, borides, nitrides, oxides, and metals were studied by the Bureau of Mines as potential fuel cell catalysts for electroreduction of oxygen in a 1[N]H2S04 electrolyte. The objective of this study was to assess the potential of abundant, low-cost materials as substitutes for platinum or to increase the catalytic efficiency of platinum. Several compounds were rejected because of their reaction in the corrosive environment of the oxygen electrode. However, some of the remaining were the most active catalysts. Activity of carbides such as tungsten carbide could be improved by doping with platinum-group metals, by varying stoichiometry, or by sputtering on a layer of platinum. While no catalysts were found with activity as high as platinum, some compounds were shown to be deserving of further investigation.

Jan 1, 1979

By Delio Amorim

Industry 4.0 concepts is the new biggest challenge on the industry nowadays and every company in every industry in every part of the globe is looking to implement this somehow on their factories and machines. To do that on the newest long rolling mills, that brings already onboard state-of-the-art technologies, is for sure a challenge of machinery builder industry, but how to become the long rolling mills built on 70’s, 80’s or 90’s part of this innovation process and connected to the new trends? This is the main mission here, to show some examples of applications that goes in this direction.

Oct 1, 2019

By P A. Lang

Canada is constructing an Underground Research Laboratory as part of a comprehensive program to evaluate the concept of nuclear fuel waste disposal deep in stable rock formations. Careful blasting methods have been designed and quality control procedures have been used for the excavation of the access headings in the underground facilities. This paper describes the work done between 1984 December and 1986 December at the second level, 240 metres below surface.

Jan 1, 1987

By Jingzhong Kuang, Zheyu Huang, Chuanzhou Guo, Pengfei Liu

"In this paper, scheelite and scheelite coated with Pb2+ (SC) were synthesized by chemical precipitation with the help of ultrasonic. The role of the Pb2+ on scheelite was evaluated. Additionally, the dissolution behavior of minerals and the adsorption mechanism of collectors were investigated systematically via SEM, XRD, EDS. The results indicate that the ultrasonic cavitation can promote the formation of scheelite with large particle size and high crystallinity. Due to the exchange of WO4 2- and OH-, the dissolution of scheelite are not in a 1:1 equivalent amount by chemical formula and the concentration of WO4 2- is higher than that of Ca2+ in the solution because Pb2+ promotes the transfer of WO4 2- from scheelite surface into the solution. The dissolution of scheelite is an endothermic reaction and its enthalpy reaches the maximum value of 692.59J·mol-1 at pH=8~10. But the coating of Pb2+ changes the thermal effect of scheelite in the solution and the dissolution of SC is an exothermic reaction with the dissolution enthalpy of -262.30 J·mol-1. At pH=8~10, the adsorption capacity of sodium oleate and salicylhydroxamic acid on the surface of SC is higher than that of scheelite which delivers that Pb2+ contributes to the scheelite surface dissolution and enhances the adsorption of collectors on the mineral surface, thus achieving activation.INTRODUCTIONIn modern society, tungsten is a type of quite important rare metal and also a strategic resource. Because of its low vapor pressure, high melting point, good electrical and thermal conductivity properties, it is widely applied in high-temperature technology, lighting, machine and engine construction (Zhao,Z.W, 2013; Yan, W, 2017; Ilhan, S, 2013). Both scheelite and wolframite are the major tungsten deposits. With the depletion of easily-processed wolframite, scheelite has drawn a great deal of scientific and industrial attention. Scheelite can be recovered by flotation due to the metathesis of polarity and chargeability on minerals surface via adding regulators and collectors."

Jan 1, 2018

By R. Buchan

A number of mineral processing techniques have been adopted for the separation of the plastics making up a typical beverage bottle, and a complete flowsheet developed. Thus, size reduction, heavy media separation and flotation were used to separate PE, PVC and PET from their mixtures with cellulose fibers and aluminum, which makes up the cap of such bottles. It is shown that while heavy media separation allows the separation of a PVC/PET mixture from the solid waste, froth flotation can be readily used to separate PVC and PET from a mixture of the two. For this purpose, the differential action of an alkaline aqueous solution (PH=II) which contains methanol and MIBC as surface tension control agents has been found to be a suitable flotation medium. This paper reports some aspects of the flotation flowsheet developed for the separation of plastics from municipal solid waste mixtures and PVC from PET.

Jan 1, 1995