Search Documents

By P. -M. Tardif, S. Outalha, R. Le

"This paper proposes a new direction to implement an underground mine communication system. It presents actual underground communication systems and discusses their technological limits. A new system based on a wireless local area network (WLAN), together with its main systems characteristics, is then proposed. This paper also presents an experimental protocol for radio frequency propagation measurements. Finally, the paper describes the projected implementation of a WLAN in an experimental mine. IntroductionDuring the last decade, a number of Canadian mining companies have invested in modern communications systems in order to automate processes and reduce operational costs. Safety of miners is also a concern, regulated by health and safety regimes.Underground communication systems rely mainly on analog technology (especially the leaky feeder). Digital upgrades have been made to modernize this technology using a coaxial or fibre optic cable to transmit voice, documents, commands, controls, and video. Therefore, all wired equipment can benefit from an increase in efficiency from the digital technology.However, when it comes to mobile equipment, the only medium was, and is, still radio waves. With the advent of the wireless local area network (WLAN) standard, one can use a technology similar to that of the cellular phone to connect transparently different equipment. WLAN enables the transmission at rates higher than 2 M bits of voice, documents, commands, controls, identification, and of course, digital video. This technology was developed with inbuilding use in mind. Now, one can try to adapt it to underground mines."

Jan 1, 2000

By E. D. Gardner

From the standpoint of tonnage and dollar value copper is the most important nonferrous metal mined in North America. The opening of copper mines has had an important bearing on the development and settlement of many sections of the continent. The prosperity of many of the mining States or provinces depends directly upon the copper-mining industry. Normally, about 35,000 men are employed in the copper mines, mills, and smelters of the United States. The United States is the most important producer of copper among the nations; more copper is mined in North America than in any other continent, and for many years the United States alone produced about half of the copper of the world. During the last 10 years increasing production in South America and Africa has reduced the relative importance of North America and the United States.

Jan 1, 1938

By Robert A. Clifton

This Bureau of Mines report discusses the mineralogy of zeolites, the properties that make them commercially valuable, the conditions of formation of both natural and synthetic zeolites, and present and potential markets.

Jan 1, 1987

The content of the book covers: (1) The theory of the Eötvös torsion balance; derivation of the working formulas; description of the instrument; method of observation; relation of the magnitudes observed to the lines of force and the level surfaces of gravity; corrections or normal effects, near and distance terrane; subterranean effects; effects due to certain mathematical bodies. (2) Notes on the practical employment of the Eötvös torsion balance; initial testing of the instrument and of accessories; hints on planning the survey; work at the station site; office computation and plotting of results; the interpretation of the results: (3) A description of the instrument and instructions for its manipulation. This book was the best discussion in English on the theory and use of the Eötvös torsion balance and is surpassed only by a later paper by the same authors that covers much of the same ground. The book is suitable for a textbook for beginners, and advanced students will find it of use. It should be available as a reference book in all geological libraries and in all torsion balance department offices.

Jan 1, 1929

By K Guilfoyle

AngloGold Ashanti Australia Ltd operates an underground mine below a large open pit at the Sunrise Dam Gold Mine near Laverton in Western Australia. Operations are based on an extensive mineralised zone which has very complex geometry, has a high ‘nugget effect’, and is difficult to interpret and model. Initial underground ore was produced from relatively narrow orebodies dipping from 15º - 70º. Open stopes aimed to selectively extract high-grade ore, using methods including jumbo stripping and longhole drilling and blasting. The complex geology makes it difficult to accurately locate development and stopes in the positions required for profitable production. In narrow stopes, rock mass damage and overbreak dilute ore grades and increase the cost per ounce of gold poured. In flat orebodies, several different techniques have been used to recover blasted ore but overall productivity is low. Thus selective mining can also be slow, costly and recovers only a portion of the available mineral resources. Large longhole open stopes with cemented paste backfill are used to extract multiple zones of mineralisation from the Cosmo and GQ orebodies. Bulk emulsion explosives and electronic detonators are used in all large stope blasts to reduce the risk of misfires and to accurately control blasthole initiation sequences and delay timing. Larger stopes improve productivity and significantly reduce direct mining costs, enabling the use of lower economic cut-off grades which increase the overall recovery of mineral resources. This paper reviews the evolution of open stoping at Sunrise Dam, the various mining methods and drilling and blasting practices used, the results achieved, and the lessons learned.

Nov 8, 2011

By Adnan A. Malik, Tadashi Maejima, Jiro Kuwano, Shinya Tachibana

"The helical piling system provides solution to many geotechnical related problems due to its quick installation, higher compressive and pullout resistance, no wastage of material, workable in limited areas and reusability. However, its use as a foundation for bridges and high-rise buildings is still limited as compared to other piling methods. In the present study, the performance and load settlement behavior of screw and straight pile is investigated under cyclic compressive load in dense ground conditions. To achieve the set objectives, pile load tests were conducted in a cylindrical steel container. The model ground was compacted with dry sand at relative density of 80%. It is observed from the test results that screw and straight pile resistance reduced when the cyclic load is applied at allowable pile resistance state. The reduction in the ultimate pile capacity is more in straight pile than in screw pile. However, straight pile showed higher ultimate pile capacity than screw pile under similar pile tip diameter. The effect of helix bending deflection on load settlement behavior and ultimate pile capacity increases under cyclic loading.INTRODUCTIONScrew pile is one of the new developments in deep foundation, which is growing tremendously fast because of its quick installation technique, less noisy operation, no wastage of material and involvement of minimum manpower. Screw piles have an edge on straight pipe piles due to its high bearing capacity and uplift resistance. The installation mechanism of screw pile is different from straight pile. Torque and pressure is required to install the screw pile whereas hammering, pressure and vibration is required to install straight pile. As the installation mechanism is different between screw and straight pile, therefore, the ground disturbance that is produced during their installation is also different. The ground disturbance produced during the installation also depends upon the pile tip condition i.e. open or closed ended. Sakr, (2009) stated that the compressive capacity of screw pile in 3 to 5 times higher than driven piles having the same shaft diameter and length. The reason for this increase in pile capacity is due to helix, which is generally 2 to 2.5 times the pile shaft diameter. Larger helices can give higher end bearing capacity but it requires very powerful machinery to install in dense grounds. For instance, if large helix screw pile is installed in a dense ground then helix-bending deflection will start affecting the end bearing capacity (Yttrup and Abramsson, 2003; Malik et al. 2013 and 2015). According to Malik (2015), the equations of thin plate (Young and Budynas, 2002) with uniformly distributed load on the plate can give reasonable estimation of helix deflection due to dense ground conditions."

Jan 1, 2016

By L. K. Smith

Flotation work conducted by CSIRO on both single minerals and high-arsenic copper ores from a number of sources, has shown it is possible to produce separate low-arsenic copper concentrates and high-arsenic copper concentrates from high-arsenic copper ores. The procedure involves controlled separations at high or low pulp potential regions exploiting subtle differences in the flotation behavior of the arsenic-bearing and non-arsenic-bearing copper minerals. An overview of several case studies investigating the applicability of the controlled potential flotation approach to the separation of copper and arsenic from sulfide copper ores is presented. It highlights the variables which influence the efficiency of the separation which include mineralogy, liberation and reagent selection. The procedure can produce a saleable low-arsenic copper concentrate, which can be directly smelted without penalty, and a high-arsenic low copper concentrate, which will require further processing. Keywords: flotation, copper, arsenic, controlled-potential flotation

Sep 1, 2012

By J. Maritz, K. de Beer, S. M. Buthelezi

The economic upheaval of COVID-19 forced companies to invest in emerging technologies to aid recovery. One such technology is extended reality, which is becoming a mature and innovative tool. Early adopters are seeing significant benefits in learning, training, immersive data visualization, and remote assistance. In South Africa, the mining industry is increasingly interested in using extended reality to optimize and innovate operations. The Minerals Council of South Africa's July 2021 report highlighted the potential of extended reality's to achieve zero-harm production and modernize the industry. However, the extent of extended reality adoption in mining remains unclear due to limited information on its usage. This study addressed this gap by distributing an online survey to assess awareness, knowledge, and current uses of extended reality in South Africa’s mining sector. The results indicated that virtual and augmented reality had the highest levels of awareness and usage, primarily for learning and training. Mixed reality, however, had the lowest awareness and knowledge levels. In terms of applications, visualization and remote assistance had the least use cases. These findings highlight that the South African mining industry is deficient in its understanding and use of extended reality technologies. Without better awareness and application, the South African industry risks missing out on the full benefits of extended reality. The study underlines the need for the South African mining industry to improve its outlook on extended reality technologies to fully leverage their potential applications and benefits.

Jul 10, 2024

By AIME AIME

THE American Institute of Mining and Metallurgical Engineers will hold its annual meeting in New York City, Feb. 9-12. The technical sessions, excepting the Sunday afternoon and evening sessions of the Mineral Industry Education Division (see the M.I.E.D. program) will be held in the Engineering Societies Building. The "All-Institute" luncheon on Monday will be at the Commodore Hotel; the Annual Banquet and President's Reception, the Smoker, and the Informal Dance will be at the Waldorf Astoria Hotel. The dinners of the Petroleum Division and the Institute of Metals Division will be at the Roosevelt Hotel.

Jan 1, 1942

By D. L. Stevens

Following an in-depth scenario and strategic-planning exercise in 1997, Noranda's mine production goal was set at 500 kt/a (550,000 stpy) of both copper and zinc metal in five years. There had been no recent discoveries, reserves were shrinking and things had to be done differently and quickly. Change is now continual in Noranda's program. The following steps were taken: the exploration and business development groups were combined, teams were formed to search for and respond to opportunity; geologists were coached to become more business minded and engineers were coached to become more optimistic; the company went global; clear thresholds were set, marginal properties were farmed out and other properties were fast tracked; reconnaissance exploration was focussed where there was a clear competitive advantage; and Noranda became a "flexible" partner to juniors and seniors. Is it working? A number of successes, near successes and outright failures are discussed. The main result is a much higher rate of opportunity flux, which is essential for success in the mining industry.

Jan 1, 2000

By J. V. Belke

There are many aspects of a grinding mill supply and installation that can result in the mill not operating as intended, resulting in unplanned shutdowns, poor reliability and headaches for all concerned. One of the largest aspects, both in criticality and physical mass, is the mill foundation; if not properly specified, designed and constructed the mill operation will be compromised. The mill foundation starts with the design specification and loading diagram supplied by the mill builder. The importance of understanding these documents and how to apply them is critical for the start of any mill project. When designing mills with a GMD the foundation must be properly modeled to ensure that all interactions of the mill and motor structures, foundation and subsurface strata behave in the intended fashion. All of the previous efforts can be laid to waste if the construction of the mill foundation is poorly handled. Mill foundations are typically the most massive concrete structure at a processing plant and can easily cause nightmares for inexperienced contactors. This paper explores some of the more important facets along the lifecycle of the grinding mill foundation.

Feb 23, 2014

By Laxman S. Sundae

Laboratory tests were conducted at the U.S. Bureau of Mines to determine the effects of roof-bolt drilling parameters on penetration rate in sandstone using tungsten carbide alloy (WC-Co) and polycrystalline diamond compact (PDC) drill bits. During the tests, water pressure of 552 kPa was found to be adequate for removing the cuttings from the tops of drill holes. Test results show that for both types of bits, penetration rate increased when thrust was raised from 227 to 1,588 kg. When water pressure rose from 554± 120 to 1,344±350 kPa, the effect on penetration rate was not significantly different. Conventional WC-Co bits became dull when one or two holes were drilled, after which the penetration rate dropped dramatically. Microscopic examination shows that the cutting edges of PDC bits also become somewhat dull, but at a much lesser rate than WC-Co tips. Microscopic examination also reveals that the wear mechanism of WC-Co and PDC bits is quite different, which may explain the longer life of the PDC bits.

Jan 1, 2010

The smelting operation associated with the production of aluminium has a voracious appetite for high grade carbon materials. Within the technical parameters of the Hall-Heroult process, the reduction of alumina to one tonne of aluminium results in the consumption of nearly 0.5 tonne of carbon at the anode of an electrolytic cell. This paper reviews the role of carbon and the basic quality requirements of carbon products in the production of aluminium, discusses the effects of certain physical and chemical specifications on smelting and related operations, and examines recent trends in the quality of these raw materials.

Jan 1, 1977

By Stephen C. Tadolini, Anand Bhagwat

"Intrinsic supports installed in mines with limited seam or mining heights have always proven to be difficult when the required support length is longer. To date, three solutions have been used to ensure that the correct length bolt is installed to achieve the required anchorage or to maintain immediate roof material: combination bolts, milled-notch bolts, and hot-notch bolts. The combination bolts use threaded sections and couples, which can be screwed together to form the required length. The primary bolt of choice, to minimize costs and achieve the desired support, has been milled- or hot-notch rebar bolts. These notches can be placed at strategic (required) locations along the bolt axis, so the bolt can be successfully bent and straightened during the installation process. However, these notches can reduce the strength of the bolting system; special reductions are detailed in ASTM F432-13 (2013). Technical advances in steel rolling and forged heading processes have led to the development of a deformed rebar bolt termed, the BORE bolt, which stands for Bendable Oval REbar. The BORE bolt can be bent at any location and straightened during the bolt installation cycle. This support exceeds the minimum designed capacities described in ASTM F432-13 and meets the yield and tensile strength requirements of a full diameter no. 6 rebar bolt. The profile and shape also reduces the resin annulus during the installation process to enhance mixing and shreds the cartridge film to help eliminate glove fingering.INTRODUCTIONThe height or depth of competent strata material, in the immediate mine roof, can be greater than the developed mine openings heights. This is especially true in coal mine openings where 50% of the minable seams in the US are less than 50 inches (132 cm). When this scenario occurs, it can be difficult to insert steel bolts in a solid single length. Figure 1 illustrates what difficulties can be experienced when a roof bolter operator is working and supporting a thin seam coal mine. There are three viable options currently available. Lengths of the bolt can be threaded and a steel coupler can be used between the sections to reach the required depth of anchorage. These systems, called “coupled bolts,” usually require a larger diameter hole to facilitate the larger coupler diameter and can be anchored with an expansion shell, resin, or a combination of both. To ensure that the coupler will develop the tensile capacity of the bolting system, required by ASTM 432-13 Standard Specifications for Roof and Rock Bolts and Accessories (2013), the threaded bars should be completely rotated and engaged into the coupler. Premature failures can occur when the threads “strip out” if not inserted completely."

Jan 1, 2018

By L. Alan Weakly

The Powder River Basin of northeastern Wyoming and southcentral Montana contains the largest strip minable reserve of compliance coal (0.27 kg or 0.6 or less Ibs of sulfur per million Btu) in the United States. In mining parlance, it is the mother lode. Wyoming's portion of the Basin is called the Southern Powder River Basin (SPRB). It has been the nation's top coal producer for the past nine years. And based on 1997 production statistics and estimated strippable compliance coal reserves, Wyoming should remain the nation's top producer for the next 51 plus years. In August 1994, ME featured 10 articles that covered all aspects of coal production in the SPRB. In this issue, five authors update the 1994 articles and provide a pre- diction of what the Basin will look like at the turn of the century. In addition to this article, the titles and authors of the other five articles include: ? "Geology of Wyoming's Powder River Basin coal field," by Gary B. Glass and Robert M. Lyman. ? "Coal quality challenges in the Powder River Basin," by Sharon Roness, Richard A. Turpin and Robert A. Young. ? "Markets for Southern Powder River Basin coal," by , Patti J. Best and Patrick W. Wright. ? "Evolution of mining equipment in the Powder River Basin," by Kenneth R. Miller and James L. Long. ? "Hauling coal into the 21st century," by Dave Willis and Will Cunningham.

Jan 1, 1998

By P Clark

This paper discusses the challenges, solutions and lessons learnt as tunnelling work continues on the Melbourne Main Sewer Replacement (MMSR) project.The MMSR project is a $220 million dollar project for the Melbourne Water Corporation. It involves the construction of approximately 4.2 km of new sewer from the southern fringe of the CBD through the inner metropolitan suburbs of Port Melbourne and South Melbourne.Of the 4.2 km of sewer currently in construction approximately 2.2 km will be constructed using a 2.95 m diameter Lovat EPB tunnel boring machine (TBM) with approximately 1.9 km of small diameter (300 to 600 mm) reticulation sewers constructed using trenchless techniques.These sewers are being constructed in a dense urban environment, which means that the tunnels and shafts are often in close proximity to buildings and structures. The underground constructionof the sewer is further complicated by the variable geology of the ancient Yarra River delta which includes weathered basalts, the infamous Coode island silt formation and fine loose sands.Some of the key challenges and lessons learnt so far during construction include:· steering and alignment control of the TBM through very soft silt with little residual strength,· development and refinement of a monitoring and alarm system for leaving the machine dormant on a day works only project,· control and measurement of tunnel lining defl ection during ring build and grouting,· prediction and monitoring of surface settlements during tunnel excavation,· improved understanding of the geology and hydrogeology at this previously unchartered area of Melbourne,· consolidation settlement due to dewatering at shafts required careful construction controls, and· ground support and excavation in close proximity to the existing 110 year old sewer which requiredvery detailed risk control measures.

Mar 8, 2011

By Dilip Banerjee

"This paper discusses the Advanced Technology Program (ATP)'s support over the last decade to the development and use of process modeling as a tool to address some of the challenges faced by the U.S. metal casting industries. A particular focus will be given to highlight how process modeling can be used to improve the manufacturability of components needed for high performance and critical applications. The challenges associated with the design and production of thin-walled, cast parts with intricate and complex internal geometries will be discussed. Modeling issues associated with the control of the final grain structure in the solidified parts will also be addressed. This paper will describe the advantages of using appropriate mathematical models for designing new alloys for use in various applications.Finally, the role that ATP has played in uplifting the U.S. technological base through partnerships with industry and academia in high-risk research in order to bring to market new and improved products for the broader benefit of the nation will be discussed.ATP's BackgroundIn the 1980s, U.S. industries were losing market share to low-cost, high-quality manufacturers from Asian countries. Corporate leaders and policy makers determined that in order to sustain and grow market share, U.S. industries needed to improve their competitiveness and productivity through product and process innovation. There was evidence that companies were systematically under-investing in leading-edgetechnologies and failing to complete the development of new technologies [l]. There were also arguments in academic circles that pointed to a potential market failure in the area of early-stage technological developments. These concerns provided impetus for creation of the Advanced Technology Program (ATP) within the National Institute of Standards and Technology through the Omnibus Trade and Competitiveness Act of 1988. Through a rigorously competitive, cost-shared partnership with industry, ATP fosters the development and broad dissemination of high-risk technologies that offer the potential for significant broad-based economic benefits to the United States."

Jan 1, 2004

By A Harding, M Chappell

Precast concrete segmental linings have enjoyed widespread use around the world, and are the lining type of choice for tunnels constructed using a shielded tunnel boring machine. However, there is significant variation in the design of such linings from one country to the next in such areas as materials, geometry, fixtures and fittings, waterproofing and reinforcement to name but a few. This arises because the speed at which the technology has developed within some countries and regions has sometimes outstripped the transfer of such technologies to the rest of the world.This paper provides some insights into the variations in lining design in different parts of the world with the aim of providing designers and constructors alike a reference for the different methods adopted. It provides a context for these developments by briefly summarising historical reviews of this subject before looking at some of the developments around the world over the last 15–20 years. The developments are presented with some reference to the reasons for implementation, and the advantages and limitations commented on. Following on from this description of the state-of-the-art, the authors also provide their own views on what developments we may see in this area in the near future.CITATION:Harding, A and Chappell, M, 2014. Precast concrete segmental tunnel linings – the state-of-the-art, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 257–266 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Mike Wongkaew, Brandon Kluzniak, Per Vilhelmsson

Rail access to Ontario International Airport (ONT) has long been a goal of San Bernardino County Transportation Authority (SBCTA) to increase public transit options to ONT and provide incoming ONT passengers improved access to San Bernardino County and the greater Southern California region. This paper describes the planning for the Design-Build-Operate-Maintain (DBOM) delivery of an emerging technology tunnel connection between the Rancho Cucamonga Metrolink station and ONT. The paper discusses key technical considerations, challenges, and opportunities; conceptual configuration development; and construction planning and establishment of the footprint for the underground connection.

Dec 1, 2022

By D R. Seaman, B Adamson, F Burns, B A. Seaman, P Manton

The Telfer concentrator, located in the Great Sandy Desert of Western Australia, consists of a dual train gold/copper operation processing ore from one underground and, currently, two open pit mines with differing mineralogy. The flotation circuit of each train was designed to operate in several modes depending on the feed mineralogy. The majority of ore mined at Telfer is processed in a sequential mode where copper minerals are first floated into a saleable copper concentrate followed by the flotation of an auriferous pyrite concentrate which is treated in an on-site hydrometallurgical plant (carbon-in-leach (CIL)). Gold is recovered as a gravity product within the primary grinding circuit, to the copper concentrate, and to a lesser extent, the CIL circuit.Since Telfer was re-opened, with a new concentrator, in 2004, the processing plant has struggled with poor copper concentrate grades, partially due to the excessive entrainment of non-sulfide gangue minerals in the copper flotation circuit and, more recently, due to composite copper particles produced when processing ore from a supplementary satellite pit that has not previously been processed through the new Telfer concentrator. Gold recoveries in the CIL circuit have also been below industry standard. This paper presents the implementation of recent changes made to the circuit to address these performance issues. The reconfiguration of the circuit has involved the installation of the following major equipment items: two ISAMillsÖ in ultra-fine grinding applications (one in the copper circuit and one in the pyrite circuit), two Jameson Cells to improve fine gangue rejection and a bank of 5 + Outotec TC30s to recovery copper and gold from the reground pyrite stream. The equipment was purchased direct from vendors and an engineering firm contracted to design and install the multi-vendor reconfiguration upgrade.CITATION:Seaman, D R, Burns, F, Adamson, B, Seaman, B A and Manton, P, 2012. Telfer processing plant upgrade - The implementation of additional cleaning capacity and the regrinding of copper and pyrite concentrates, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 373-382 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012