Search Documents

By Dan B. Kivari

One of the key operations in any milling circuit is grinding. Over the last two decades, large diameter Semi-Autogenous Grinding (SAG) mills have become the preferred primary grinding mills. The drive systems became more complex as the size of the mills became larger, during which time operating and design experience for SAG mill accumulated. Considerable reliance is now placed in power electronics to provide flexibility in SAG mill operation to meet the demands of lower operating costs. Whereas earlier most SAG mills were designed to operate at fixed speeds, present day SAG mills can operate at a fixed speed or variable speed through the use of an AC synchronous motor or DC motor. However, this flexibility comes with an increase in capital and operating costs. Since the capital and operating costs of a project directly affect the project's rate of return, the selection of a SAG mill and its drive system should depend, in part, on the impact that the extra cost makes on the project. This impact can be measured by performing an economic analysis based on Net Present Cost (NPC) calculations. Although the NPC calculation is an important factor in the grinding mill selection, other factors such as reliability of mill drives and power source are important elements in the decision making process. This paper examines how the NPC calculation, plus reliability and power source, influence SAG mill selection.

Jan 1, 1991

By R Knight

"In project evaluation there are two matters of keen interest to non-executive directors: the process by which an investment recommendation is reached, as well as the investment itself, as presented. It is sometimes mistakenly believed that Boards of directors are interested only in the result. That is not so. The process by which project evaluations are derived and socialised with the Board is as important as the result, sometimes more so.Setting aside the gloomy predictions of the doomsayers and looking through short-term volatility in supply and demand, the overall availability of mineral resources more often than not exceeds demand. There are in reality more development projects in prospect at any one time than are needed to meet the market. Only the fittest will prosper, although some others may survive.Optimism springs eternal in the mining industry and every project promoter, executive or entrepreneur has a convincing project development case. Some will create value for shareholders, but the historical evidence suggests that many will fail to meet the expectations set in their evaluation.Boards of directors make the final decision to invest, or not, in a new mine. Knowledge is power, and on that basis the balance of power favours management. Management has the facts (or in some cases, what passes for fact) and the passion to invest. The non-executives have the power of approval – yes or no – but before making a decision directors must demonstrate due diligence, the essential precursor to project approval.Management has a vital part to play in facilitating that due diligence process and in encouraging the independent thought processes of the Board. A closed approach by management fosters a negative, risk-averse attitude on the part of the Board. One that encourages an understanding of the rigour of the project evaluation process and the robustness of the result will allow directors to understand better the implications of their decision.CITATION:Knight, R, 2016. Project evaluation – a non-executive director’s perspective, in Proceedings Project Evaluation 2016, pp 11–19 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By Paolo Cavalcoli, Federico Pagliacci, Marco Chiarabelli

"The Sheikh Jaber Al-Ahmad Causeway Project in Kuwait is estimated at approximately $US3.7 billion and consists of constructing a causeway across the Kuwait Bay, connecting the Shuwaikh Port with the northern Subiyah area, where the new “Silk City” will be established. The $US77 billion Silk City will revive the ancient “Silk Road” trade route and will become a major free trade zone linking central Asia with Europe. The new city will be completed in 2030, it will house about 700,000 people and, furthermore, it will include the tallest tower in the world. The Causeway will stretch approximately 23.3 miles and will be composed of a combination of low-level bridges, embankments and transition islands. A bridge of about 16.8 miles in length will span the navigation channel and a free flow interchange at the Shuwaikh Port will connect the causeway to the main road network in Kuwait City. The geo-construction portion of the project involves the execution of 1,200 drilled shafts with diameters of 98 inches and 118 inches embedded to a maximum depth of about 276 feet. Details are provided concerning the subsurface conditions, the geotechnical characteristics and the strength parameters, illustrating, as well, the installation technique implemented for the construction of the drilled shafts. In addition, particular attention is paid to the description of the challenges faced while constructing the drilled shafts at a distance of about 10 miles from the shore, such as the depth of the water above the midline (more than 160 feet), an underwater current and the tidal variation.INTRODUCTIONThis paper presents an overview of the foundation works executed for a 37km causeway across the Bay of Kuwait, connecting Shuwaikh Port with Subiyah New Town Development. The project, in which Trevi is actively engaged, includes a 27 km low-level bridge across the bay, a main bridge with a span of 200 m, an overpass and a 5 km approach road onshore in Subiyah.The main purpose of this report is to provide information about the nature and features of the applied technique of bored piles, including a description of each work phase and other related details, in order to aid in the design of the foundations for the proposed construction.Works for the soil investigation were carried out in accordance with accepted geotechnical standards/guidelines. Brief descriptions of the methodology of the field are also provided in this report."

Jan 1, 2016

By B E. McCarthy

Red Dome Mine was a highly complex gold copper operation developed over a number of phases between mid-1986 to October 1997. With only three years of production ahead at any time, a proactive practical approach to mine closure was necessary. In 1989 the Domains Concept to life-of-mine planning and mine closure was created as a response to the proposed changes to legislation.The Domains Concept, a relatively simple idea developed to integrate mine closure during production at Red Dome, has been broadly adopted by both government agencies and industry in the intervening 20 year period. Over time the author has observed that the concept has been poorly applied, misunderstood and in some cases even misrepresented. As a consequence, the potential opportunities from applying the concept, including the optimisation and minimisation of life-of-mine costs, mitigation of long-term financial liability exposures and building credibility with the general community, have been missed.This paper examines the many benefits, advantages, applications and perceived barriers to developing and integrating a fully costed life-of-mine plan. Integrating the Domains Concept early in the project, within the operational budgeting, allows the production of a meaningful and useful document, representative of a whole life-of-mine, cradle to grave, with measurable rehabilitation and closure outcomes when the concept is used to full effect.The Domains Concept serves to optimise cost-effective, whole of mine, life cycle planning which provides beneficial outcomes for the community, significantly mitigates legacy issues and contributes to the attainment of compliance and sustainability principle objectives.CITATION:McCarthy, B E, 2014. The domains concept – 20 years on retrospective, obstacles and opportunities for effective life-of-mine implementation, in Proceedings Life-of-Mine 2014 , pp 621–636 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By Shigetoyo Yasui, Masahiro Saitou, Nobushige Yasuoka, Keisuke Tsujimoto

"The Dry Jet Mixing (DJM) Method was developed and has been put to practical use on the initiative of the Public Works Research Institute and Japan Construction Method and Machinery Research Institute. This method is used to inject powdery binder with compressed air into soft ground while mixing the binder with the soil using the mixing blade to reduce the moisture content of the ground and cause chemical reactions between the soil and binder, thereby strengthening the ground and stabilizing its quality.Recently, there is a demand for high-quality, high-accuracy execution control.This paper introduces the New DJM Execution Control System, developed to meet the future demand for more sophisticated ground improvement, based on the past results of the conventional system in order to provide new automated execution control with improved accuracy, functionality and column quantity.1. INTRODUCTIONIn association with the densification of cities and the improvement of the social overhead capital, the underground space in urban areas is tangled with various underground structures including transportation facilities such as subways and underground roads, buried pipe such as water supply and sewerage systems,gas, electric power and communications lines, and underground malls.In addition, a lot of aboveground structures such as office and residential buildings, elevated tracks, expressways, embankment tracks are also supported with underground foundations.Tokyo, Osaka, Nagoya and many other large cities in Japan grow on plains spread along the coast or rivers. Waterfront flat areas which are very convenient for human activities, however, are often on the alluvial soft ground, where soft cohesive soil with a high moisture content, loose sandy soil, etc. are accumulated in a thick formation, with a high groundwater level.The DJM Method introduced here is used to decrease the moisture content of the soft ground, strengthen the ground and stabilize the soil quality by injecting powdery binder into the ground with compressed air, while mixing the binder with the soil using the mixing blade.2. OUTLINE OF DJM METHODThe DJM Method is used to inject powdery binder with compressed air into soft ground, while mixing the binder with the soil using the mixing blade, to cause chemical reactions between the soil and binder, thereby decreasing the moisture content of the ground and strengthen and stabilize the ground."

Jan 1, 2015

By I. N. Gridasov, T. V. Ignatova, E. V. Shelepov

"Mikhailovskoye Deposit is comprised of oxidized ferruginous quartzites among other minerals with the former widely spread across the ore field and mined along with unoxidized ferruginous quartzites. PJSC Mikhailovsky GOK strategic development is aimed at iron ore product output expansion. The most critical item of the strategic development road map is process design for separation and concentration of hematite contained in oxidized ferruginous quartzites mined as the by-product in the open pit. Laboratory and semi-industrial tests run to design cost-effective, reliable and environmentally friendly process for Mikhailovskoye deposit oxide quartzites processing included the following processes: - pilot tests of reverse anionic flotation which produced concentrate with Fe60.1-62.9% total iron content and 66-69%Fe recovery rate; - combined magnetic separation and flotation (Marubeni Company, 1982) including slime removal, reverse anionic and cationic flotation and high gradient magnetic separation resulting in 48.9% yield, Fe55-57.5%, up to Fe60.5% hematite concentration ( Fe64.1% being the best result achieved),76.2% recovery. - magnetic separation and flotation, including separation in low gradient (1400 Oe) and high gradient (up to 17000-18000 Oe) magnetic field. The results of these pilots tests were the following: 57-59%Fe concentrate, 70%Fe recovery (Mekhanobrchermet, MGOK, 1982-1988): - magnetic roasting in pilot plant of TSGOK (Krivoy Rog) which produced 61.1%Fe concentrate with 81.5% recovery. Major disadvantage of the method is high generation of dust equal to 20% of the initial feed. Based on third-party studies flotation of oxidized ferruginous quartzites process embracing best processing methods was designed by Metalloinvest Management Company LLC and PJSC Mikhailovsky GOK engineers. This paper discusses analysis of studies aimed at intensification of separation processes with application of mechanical slurry agitation (MSA), addition of alkali (NaOH) and elutriation of initial feed. The paper also provides a design solution to implement a lab-scale MSA plant. It includes feasibility evaluation of MSA inclusion in flotation of oxidized ferruginous quartzites process to enable higher yield and hematite recovery in resultant concentrate. Outcomes of the discussed work have significant value for prospective engineering of OFQ concentration process."

Jan 1, 2018

By J. W. Byrkit

Design features and operating methods at the new Ajo smelter are described in detail. Successful operation of a novel method of handling and charging wet concentrates to a deep bath type reverberatory furnace contribute to the daily production of 200 tons of anodes with good results from the standpoint of both metallurgy and economy. THE New Cornelia Branch of the Phelps Dodge Corp. is located at Ajo, Ariz. Large scale mining operations were started at Ajo in 1917, when a 5000 ton leaching plant was put in service to treat the copper carbonate ore that overlaid the sulphide ore-body. In 1924 a 5000 ton flotation plant was built to treat the sulphide ore and the leaching operation was abandoned a few years later. Changes in practice and additions to plant facilities have resulted in a gradual increase in the milling rate which now approaches 30,000 tons daily. Prior to the erection of the Ajo smelter, flotation concentrate was shipped by rail to Douglas, Ariz, where it was treated in the Phelps Dodge smelter. Construction of a one reverberatory furnace smelter to produce an average of about 200 tons per day of copper anodes at Ajo was started early in 1949. Initial heating of the reverberatory furnace was begun on June 21, 1950. Charging the furnace was started on july 8, and the first anodes were cast on July 14. Neither the anode furnace nor the reverberatory furnace has cooled since the initial firing. Fig. 1 is a photograph of the new smelter. Built primarily to eliminate the '300 mile haul of concentrate to the Douglas plant, the new smelter was designed to treat the Ajo concentrate, with a minimum of capital investment. A novel, and relatively simple, method of concentrate handling and furnace charging made unnecessary the installation and operation of expensive storage facilities and reclaiming equipment, and obviated the necessity of holding in storage large quantities of copper-bearing materials. (Patents are pending in the United States and abroad on the Ajo process.) In the selection and arrangement of equipment, consideration was given to the full utilization of all smelting facilities, reducing the amount of idle equipment to a minimum. The layout of the smelter is shown in Fig. 2. The important problem of internal transportation was minimized by arranging the reverberatory furnace, converters, and anode furnace in a compact group and providing storage bins inside the smelter building, within reach of overhead cranes, for fluxing materials and other supplies needed in the daily operation. This can be seen in the sectional view of the smelter given in Fig. 3. Incorporated in the design were many innovations in smelting equipment intended to facilitate operations and effect economies in maintenance expense and manpower requirements. Table I gives operating data of the entire plant. Metallurgy The metallurgical practice at Ajo is based essentially upon the use of a single, deep bath reverberatory furnace for smelting wet concentrate, without concentrate storage facilities. The large reservoir of slag and matte maintained in the furnace serves to equalize, to some extent, the day to day variations in the nature and grade of concentrate and permits

Jan 1, 1954

By S. J. Pearce

The need for a simple, very sensitive, and accurate method for the determination of benzene in blood and urine was evident throughout a recent study of chronic benzene (C6H6) poisoning conducted cooperatively by the United States Bureau of Mines, The Barrett Company, and the producers of benzene. A combustion method which will be described in a later publication, end a previously described5/ adaptation of Smyth's method were developed and used during that investigation. The adaptation of Smyth's method gave satisfactory results when dealing with exposure conditions that produced chronic poisoning in a comparatively few days, but it was time-consuming and lacked the accuracy necessary for a study of the absorption, distribution, and fate of benzene in the body during exposure to threshold concentrations of benzene vapor in air. The combustion procedure was satisfactory from the standpoint of sensitivity but was cumbersome, intricate, time-consuming, and required the use of special and somewhat expensive physical and. chemical apparatus. Following the termination of this study of chronic poisoning, possibilities for developing better methods occurred, and these have been investigated by the Bureau of Mines with the aid of Relief Works Division personnel. A microcolorimetric method for the determination of benzene in air has been described recently.6/ The present report deals with the adaptation of this new colorimetric method to the determination

Jan 1, 1936

By M. J. Ferrante

The Bureau of Mines recovered rhenium powder from scrap tungsten alloy containing approximately 25 percent rhenium. Oxidation of the scrap at 950° C separated volatile rhenium heptoxide from tungsten trioxide. Minor amounts of tungsten, iron, and nickel were removed by selective precipitation from a rhenium solution from which was recovered crystalline ammonium perrhenate. Experimentation showed that hydrogen reduction of minus 325-mesh ammonium perrhenate at 1,000° C produced rhenium powder averaging 2.1 microns in size (Fisher Sub-Sieve method). The powder contained <50 ppm of total metallic impurities and 1,070 ppm of total interstitial impurities. Sintered compacts had a density of 95 percent of theoretical. Approximately 96 percent of the rhenium contained in the scrap alloy was recovered.

Jan 1, 1969

By Uwe Wilhelm

Pittini Group has contracted Danieli in 2011 for the supply and replacement of the existing EAF at Ferriere Nord Plant in Osoppo. This was a very challenging project: giving the fact that the Meltshop was operating already under very high performance level, there were many elements involved for the project to improve (reduce the amount of charges, promote highest possible chemical energy utilization, allow best optimization on existing transformer power, modification on Drop Out box and Water Cooled Duct, Hydraulic System for EAF, Scrap Bucket design to fit to new EAF with existing loading and transport system, Automation System Review and Upgrade) as well as limitations of the existing installation (limited space, lifting capacity building and cranes and the required solutions for fast shell and roof exchange). All furnace parts, as well as installation engineering, were developed and discussed carefully with the Customer to either provide proven and reliable concepts, but also to define solutions for fast installation/maintenance access and quick exchange for offline turnaround. In the end, from disassembly of existing equipment up to the first heat of the new furnace, only 38 days were necessary. First heat was made on January 24th 2013, on the 6th production day 32 heats where produced at nominal design capacity and 28 days after start up 100,000 t liquid steel have already been produced.

Jul 30, 2018

By J. Bilant, J. Donnelly

"A spatially-discretized heap leach simulation model was developed within the GoldSimTM modeling framework for the Coeur Rochester Mine, Nevada. The model is being evaluated by Rochester as a means of improving forecasting of silver and gold production on an actively loaded valley fill heap leach facility. Optimization of future heap leach operations and crusher product size is also being evaluated with this software. Simulation modeling incorporates metallurgical data such as mine planning, particle size distribution of placed ore, stacking plans, pad geometry, and leaching dynamics. The heap leach model is represented as a discretized matrix with lifts providing vertical separation to form 19,840 spatially discrete cells. Each cell is quantified with regard to ore properties and metal content. The model tracks solution and cyanide-complexed silver and gold within each cell as a function of time based on pad operations, unsaturated flow properties, and kinetic rates. Practical heap leach management and daily operation will be discussed as it relates to the simulation and forecasting model. INTRODUCTION The Rochester mine, and associated valley fill heap leach facilities, is an open-pit silver and gold mine located in Pershing County, Nevada. In 2015 Rochester produced approximately 4.6M troy oz silver (Ag) and 52K troy oz gold (Au) through combined cyanide heap leaching of the Stage II, III and IV heap leach pads with recovery via a Merrill Crowe process plant. Rochester is actively stacking and leaching ore on the Stage III Heap Leach Pad. The Stage III pad contains approximately 70M tons of ore in a valley fill configuration and is forecasted to receive an additional 20M tons of ore by the life-of-pad in 2019. The ultimate height of the pad is permitted to be 400 ft above the liner and solution collection system. Approximately 80 percent of the ore loaded on the Stage III pad is produced from tertiary crushing split from two crushing circuits that produce a nominal 80 percent passing 3/8” product. The remaining material consists of run-of-mine (ROM) from off loads of re-mined waste rock stockpiles. Metallurgical testing of the ore indicates low variability in geologic properties and high variability of both Ag and Au extraction rates for the various particle size distributions. Historically the valley fill configuration provided metal forecasting challenges that could not be predicted as the leach pads grew. Forecasting metal production and leach optimization of the Stage III pad became challenging due to the extreme variation in heap leach pad depth, application of available barren leach solution and the variability of Ag and Au extraction rates for the various ore particle size distributions. To assist with understanding and optimizing metal production forecasting with these factors for the Stage III pad, Hatch developed a spatially-discretized heap leach simulation model using GoldsimTM dynamic simulation software. The model incorporates metallurgical data such as mine planning (tonnages and grade), particle size distribution, ore crushing, ore stacking plan, pad geometry, and both leaching dynamics and kinetics to forecast metal production from a consolidated mine plan."

Jan 1, 2017

By F. E. Brantley, D. A. Martin

Synthetic zeolites were tried as selective adsorbents for recovering sulfur dioxide from synthetic gases and gases produced from gypsum decomposition . Initial adsorption tests , using the synthetic gases , indicated that three of these compounds , having sulfur dioxide capacities of up to 29 grams per 100 grams of adsorbent , were satisfactory . Regeneration studies showed that over 90 pct of the sulfur dioxide desorbed from the loaded beds was of sufficient purity for direct liquefaction . However , all zeolites tested lost adsorptive capacity with repeated use . The zeolite determined to be the most promising in the preliminary synthetic gas tests was also evaluated for capability in adsorbing sulfur dioxide from gases produced by the thermal decomposition of gypsum . Despite small amounts of hydrogen sulfide in the gypsum decomposition offgas , good adsorption of sulfur dioxide was attained . The economic practicality of utilizing zeolites for sulfur dioxide removal from industrial gases was not evaluated , but the technical feasibility was demonstrated .

Jan 1, 1963

By E. D. Sehnke

The refractory materials industry provides the largest commercial market for nonmetallurgical grade bauxite. Refractory grade bauxite is prepared from bauxites having low iron, titania, and alkali content by calcining at temperatures near 1,650° C. Although there are substantial bauxite reserves in the world, premium grade bauxite ores suitable for use in refractory applications are limited to only a few specific sources, primarily in Guyana and the People&apos;s Republic of China. Consumption of bauxite for refractory use is closely associated with the production and consumption of primary metals, in particular iron and steel. Barring major disruptions within the principal producer nations, sufficient supplies of refractory bauxite will be available to meet world demand well into the next century, and raw material costs will continue to determine the availability of markets for bauxite-based refractory products.

Jan 1, 1992

By C. C. E. Pretorius, V. M. Mathoho, A. van Zyl, R. J. Mostert

The in-service degradation of the mechanical properties of steel components through the damage mechanism of high temperature hydrogen attack (HTHA), is a topic of concern in the refining and green hydrogen industry. This damage mechanism occurs in susceptible steels operating in environments at high temperatures and hydrogen pressures. The current investigation deals with the indirect monitoring of mechanical degradation via tracking of the swelling strain in affected structures. An autoclave with an AISI 316 shell was utilized to simulate accelerated HTHA damage at 550 °C and 46 bar for exposure times ranging from zero to 700 hours. The progress of the HTHA damage was tracked using encapsulated high-temperature strain gauges. The correlation between the swelling strain and mechanical property degradation was studied to develop a methodology for the continuous monitoring of embrittlement. The tensile sample orientation of the carbon steel plate was included as a variable, i.e., samples parallel, transverse, or perpendicular to the plate rolling direction were included, since it has been shown that the sample orientation influences the HTHA damage features. For the through-thickness orientation, and upon exceeding a threshold value of exposure time, all tensile properties were severely degraded, with values in the order of a 90 per cent reduction being observed. It was found that the degradation of carbon steel mechanical properties can be correlated to the swelling strain measured during exposure. The critical point for mechanical property degradation in the plate through-thickness orientation, whereafter a severe decrease in the ductility of the material occurs, was found to be in the order of 1% of the total swelling strain measured during exposure, equivalent to 65 microstrain. This threshold was found to be significantly lower than that expected from the literature, where limits of 400 to 1000 microstrain were postulated.

Nov 27, 2024

As part of a continuing program of evaluating the Nation&apos;s crude-oil resource, this report presents information pertaining to resource, primary reserve, and potential waterflood reserve for 3,209 selected reservoirs contained in 24 oil-producing States, as of January 1, 1968. To that date the selected reservoirs had not been subjected to pressure-maintenance or secondary-recovery operations. These reservoirs also met the following parameters: (1) a minimum of five oil-producing wells on January 1, 1968, (2) a minimum of 50 acres areal extent, (3) a minimum of 50,000 bbl of oil ultimate primary recovery, and (4) the principal reservoir energy was other than active water encroachment. The selected 3,209 reservoirs produced 527 million bbl of oil in 1967, about 17 pct of U.S, total production. Primary oil reserve was 4,983 million stb; in addition, there was 6,043 million stb of potential water- flood oil reserve. Oil resource in the selected reservoirs was 59,547 million stb. A brief history and outlook of waterflooding are presented for each State. Depth and producing rate statistics and geologic distributions of production, resource, reserve, and potential waterflood reserve for the selected reservoirs are presented by States in the appendix. Also included in the appendix are description, history, and technique modifications of waterflooding, and a preliminary cost estimate of a closed-system water-injection project.

Jan 1, 1970

By Luis Acainas Caballero, Karl Hoen, Stephan Krämer, Christoph Klein

The situation of the steel industry is still challenging. Worldwide overcapacities have an impact on profitability. More than ever, the point at SMS group is to provide the steel industry with flexible and profitable technologies and systems over the whole process chain. One example for that is the thin slab casting and rolling technology and, in particular the CSP® technology (Compact Strip Production), being well established for hot coil production. From its introduction in 1989, CSP® technology has been continuously further developed. Today, on a CSP® plant, the full range of high-quality steel grades can be produced with tightest geometrical and metallurgical tolerances under optimal economic conditions. With the introduction of semi-endless rolling and, as a further step, the endless rolling process, the product range for thin and ultra-thin products has been further enlarged, allowing for the production of hot rolled coils with a thickness of 0.8 mm for low carbon steel grades. Also high-strength steel grades may be produced with gauges below the minimum product thickness that can be achieved in a conventional-type hot rolling mill. Another step in the further development of CSP® technology is digitalization. In December 2016, the CSP® plant of Big River Steel (BRS), located in Arkansas, USA was put into operation. It is the first learning steel mill in the world. The CSP® plant of BRS comes with innovative technologies, providing impressive operational results right from the beginning.

Oct 1, 2019

By J. D. Dixon

This Bureau of Mines report describes the results of an investigation for developing and applying procedures for stabilizing excavations openings in highly yielding ground. The approach developed in this report involves nonlinear modeling of the progressive relaxation of the zones of rock mass around the excavations opening where Coulomb criterion of failure is exceeded. Stresses are calculated by using a computer code; Coulomb-failure condition is examined for both intact rock and joints (using strength parameters [~] and c). The rock mass in the failed zones is relaxed by reducing the Young&apos;s modulus of the rock based on an empirical formulation that is a function of the shape of the opening and the extent of the failed zone. In addition, the material in the failed zone is assigned reduced strength paramters 0&apos; and c&apos;. The limiting (or convergent) relaxed zone is obtained through an iterative process by manually changing the rock modulus and the strength parameters between iterations. Support pressures are computed by applying forces normal to the excavation surface. The approach is applied to the analysis of stability and support requirements for an entry in a longwall coal mine.

Jan 1, 1985

By J Elder

Magnetic separation equipment has long been used to upgrade and beneficiate a wide variety of minerals and materials. Over the years, significant advances in both wet and dry magnetic separators have improved their operability and separation performances, broadening their use.But no one answer exists to the question: what is the right type of magnetic separator? For many minerals, including ilmenite, both process routes may be viable. There are technical, production, as well as economic reasons for choosing wet versus dry. However, recent developments illustrate that a new generation of wet magnetic separators is approaching performance once seen only in dry magnetic separation. With quality and production performance becoming similar, the choice between wet and dry magnetic separation is not as cut and dry as it once was.

Oct 5, 2011

By Albert L. Toenges

The introduction of mechanized mining in coal mines, which has speeded loading, has emphasized the importance of efficient underground transportation systems. The purpose of this investigation is to study and analyze various systems now in use, and to derive conclusions therefrom. This report may be helpful to operators who are planning new systems of transportation or who are revising present systems to increase their efficiency. This paper is the first of a series on this subject and describes some systems of transportation utilizing rail haulage. ACKNOWLEDGMENT The information used in preparing this report was obtained through the courtesy and cooperation of the officials of the companies whose mines were studied. The descriptions of the transportation systems at the mines included herein have been checked for accuracy, and publication of the data has been approved by the executives of the several operating companies.

Jan 1, 1940

By L. E. Bowman

Efficient filtration of fine kaolin particles plays a crucial role in processing of raw kaolin to a marketable product. Oftentimes, filtration Is the rate controlling step of the whole process. As a consequence, plant production is dependent, to a great extent, on the rates being achieved In filtration. In order to alleviate the bottleneck in production, Nalco Chemical Company initiated a reagent development program to chemically enhance the performance of the filtration units. Filler aids of different classes were synthesized for evaluation. These include reagents whose primary mode of functionality were: coagulation, flocculation, thickening, and combinations of the preceding. All reagents that were synthesized and tested were listed under the appropriate Food and Drug Administration sections of the Code of Federal Regulations. This paper discusses the development and application of a new reagent that Improves the filter production rate with minimal Impact on filter solids. The results of laboratory filter studies along with plant data are presented and discussed. Plant data indicate that this reagent is capable of increasing production rates by as much as 35% on various clays of coarse particles to the finest fractions, as well as clays that are calcined. The reagent&apos;s Impact on solids content, re-slurrying characteristics, Brookfield and Hercules viscosity, and drying is within the standards set by plants who have evaluated and now use this product.

Jan 1, 1993