Search Documents

By T. M. Barton

Coal mine bumps the violent failures of over-stressed coal', present a safety hazard to miners when mining is conducted in deep, bump prone coal mines. Two different longwall gate entry systems were evaluated in a Southern Appalachian coal mine located in the Pocahontas No. 3 Coalbed under approximately 610 m of overburden which included a massive sandstone member. Both gate entry systems employed a center abutment pillar flanked by yield pillars. The original design employed a 24.4 m square abutment pillar' while the new design employed a 36.6 by 54.9 m' abutment pillar. Rock mechanics instrumentation data analysis and in-mine observations indicated that this increase in abutment pillar size significantly decreased bump potential. The new design in worse case conditions increased effective bearing area 62 pct with only a 9 pct increase in gate entry system width and eliminated face bumps that wer7 experienced with the original gate entry design.

Jan 1, 1991

By Frank Agyemang, Zainab Nasrullah, Richard LaDouceur, Mehran Saddat

To sustain the circular economy, defence applications, and other renewable technologies, recycling rare earth elements (REEs) and other critical elements from their secondary resources is important. This cause has resulted in rigorous research and development for viable extraction and separation of REEs. Previously, Sm-Co recycling has been done with technologies, which fall under the categories of pyrometallurgy, physical separation, and hydrometallurgy. All these methods have limitations associated with energy, cost, and environment. Reportedly, the chemical leaching technology has successfully recovered and separated Sm-Co. Still, it has limitations associated with slow mass transfer and leaching kinetics, and there is a need to intensify the process to make it time efficient. This approach has also adversely impacted the environment by an extensive use of toxic, corrosive, non-selective, and expensive reagents. In this research study, chemical leaching of Sm-Co was performed using this new class of solvents, Deep Eutectic Solvents (DESs), which fall under the category of ion metallurgy. Four different DESs were used, proven to be green, non-toxic, biodegradable, cheap, and selective for cobalt over samarium by 82% leaching conversion. To improve the slow mass transfer and leaching time, this new technology of resonant vibratory mixing (RVM) was also tested. RVM intensifies mixing by establishing near instantaneous, low energy mixing conditions through resonance. It has been shown to improve the adsorption kinetics and was tested for the leaching kinetics. Four combinations of DESs were prepared, which are made up of two quaternary salts: Choline Chloride and Tetra Butyl Ammonium Chloride, and three organic compounds: Oxalic Acid, Urea, and Ethylene Glycol. These combinations were used for chemical leaching of Sm-Co with leaching factors of time, temperature, and type of DESs. After leaching, the samples were tested with and without resonant vibratory mixing with conditions of time, intensity (%), and type of DESs. Samples were analysed with Induced Coupled Plasma - Optical Spectroscopy (ICP - OES). Future work will involve a life-cycle assessment to assess the RVM technology with other conventional mixers, and an extensive study of DES properties to improve selective leaching.

Feb 1, 2025

By B. Weyerman

U. S. Steel's Oak Grove Mine experienced several top hinge failures on their caving shields. It was determined that all the caving shields needed to be replaced with new caving shields before more thilures occurred. The cost and amount of time needed for several scenarios of caving shield change outs were compared. This paper discusses how Oak Grove Mine decided to and did change 126 caving shields in six specially designed jig stations underground during a longwall move using their own UMWA employees.

Jan 1, 2001

By S France

The Waterview Connection will complete a strategic Auckland motorway route linking the south, west and north. The project will comprise 2.5 km of ‘undrained’ driven tunnels and 900 m of drained cut-and-cover tunnel and portals.The project is aligned beneath a stream valley of Oakley Creek incised through alluvium and in places overlain by landfill, between Mt Albert volcano and a ridge formed in alternating sandstones and siltstones. The hydrogeology of the area is complex with perched aquifers in compressible soils, cascading water levels in fractured rock aquifers, and discontinuous higher permeability units resulting in artesian water levels and groundwater springs.Numerical groundwater modelling was undertaken to assess the potential effects of tunnel construction and long-term operation on the groundwater system; the magnitude and extent of changes in groundwater level and the resulting potential for settlement, buoyancy effects, contaminant migration and adverse effects on creek base flow. Modelling also provides inputs to tunnel design such as groundwater seepage volumes and water pressures.The driven tunnel will be ‘undrained’ long-term so potential effects on the groundwater system are limited to short-term dewatering during construction. Significant project time and cost savings can be made if the portal areas are permanently ‘drained’, but this means potential effects are greatest in the long term condition.This paper summarises the investigations, implications of the complex hydrogeological setting on tunnel design and environmental assessments, and groundwater modelling undertaken during the planning stage of this project. The groundwater modelling has been used to incorporate mitigation options in tunnel design and construction sequencing; a comprehensive monitoring program will be used to trigger appropriate responses should effects differ from those predicted.

Mar 8, 2011

By Roy A. Grancher

HAPPY BIRTHDAY Not only is 1971 the Centennial Year of the AIME, but it also marks the One Hundredth Anniversary of the United States Portland Cement Industry. On September 26th in 1871 David O. Saylor of Allentown, Pennsylvania, received his patent Numbered 119,413 for the manufacture of portland cement. "Cement" had been used in the United States before that. This was, however, natural cement - a direct product of rocks as found in nature, usually burned at low temperatures in open kilns. During the early 1800s this natural cement played an important role in such projects as the building of the Erie Canal. It was only after the Civil War that small amounts of high priced portland cement was imported from Europe. The successful use of this material in construction led to Saylor's experiments and subsequent patent for the manufacture of a scientifically controlled product in this country. These one hundred years have witnessed four major "ages" of cement . . . three of them occurring in the last quarter century since World War Two. The first age was the "Age of Development", a seventy-year period which saw the growth of cement and its concrete end uses as major construction materials. Next followed a period called the "Age of Demand" when, after the war, cement became in short supply relative to large building requirements. In effect a cement shortage existed. The decade of the Sixties proved to be the "Age of Reaction", with its courses of action coming in response to the problems that arose when the industry's expansion programs provided too much capacity. Today cement, and the concrete industries, find themselves entering the "Age of Reason". Overcapacity, low price, rising costs, and poor returns are several of the reasons behind that name, As these industries face the construction challenge of the Seventies, and beyond, the application of basic management principles (otherwise known

Jan 1, 1971

By A. Baydusa, K. Barron

A theory for cutter roof failure in coal mines has been developed. It is shown that the key parameters influencing the likelihood of cutter roof failure are the rock strength, the vertical stress (depth) and the horizontal to vertical stress ratio. The support force necessary to prevent the development of this mode of failure is, in most cases, so high as to make it impractical to apply a force of such magnitude. It is, therefore, better to allow the failure to occur and to design a bolting system to support the dead weight load of the failed block. This is probably best achieved by using a yielding bolt system (such as split set bolts) which is anchored well beyond the top of the potential failure block. The maximum potential caving height determined from this theoretical approach compares favourably with field observations reported in the literature.

Jan 1, 1999

By A. E. Dyment

In formulating an explosive for any specific set of conditions, various factors must be taken into consideration. Is it to be subjected to water or moisture? .If so, it must be designed to have an inherent ability to resist water. Is it to be used in confined spaces underground, where ventilation is limited? If it is, it must possess qualities enabling it to form, upon explosion, the minimum quantity of noxious gases, such as carbon monoxide or oxides of nitrogen. Is it for use where low temperatures may possibly prevail? If so, it must be capable of resisting such temperatures without freezing. Is it for use where dust or inflammable gases may be present? If it is, then it must be so formulated as to produce, upon detonation, a flame of the lowest possible temperature and the shortest possible duration, in order to lessen the chance of ignition of such gas or dust. This is actually the essential property of a permitted explosive, and it is undoubtedly the most important characteristic of an explosive which is to be used in gassy or closed-light mines. This being the quality that distinguishes permitted explosives from other types, it is interesting to investigate the ways and means by which the low-flame-temperature characteristic is obtained . Generally speaking, such explosives are so designed as to contain comparatively small quantities of nitroglycerin and relatively large quantities of the strength-producing salt, ammonium nitrate. This ingredient does not develop as high a temperature upon explosion as does nitroglycerin, so its presence, in large measure, in place of nitroglycerin results in an explosive which has an inherent low-flame-temperature characteristic, as opposed to one which is .made up largely of nitroglycerin, which would ordinarily be in the high-flame-temperature class. Additions are also made of flame-quenching salts such as sodium chloride, ammonium chloride, and up to a certain limiting percentage of sodium nitrate. These salts, with the exception of the last, do not ordinarily take an active part in the explosive reaction, being present primarily to absorb heat liberated by the reacting ingredients.

Jan 1, 1947

By Angela Binder, Mareike Schubert, Yichen Jiang, Sandra Nowosad, Oliver Langefeld

GermanyINTRODUCTIONThe mining industry is currently characterized by various factors such as environmental impact, resource scarcity, social responsibility and geopolitical uncertainty. The production of minerals required to meet the demand for renewable energy is expected to increase by 500 % by 2050, particularly for critical minerals such as graphite, lithium and cobalt 1. Easily accessible deposits are often depleted, meaning that deeper and more complex deposits need to be developed. Furthermore, investors’ value systems have shifted towards more sustainable practices. Alternative approaches to solving this problem are therefore currently being developed, such as the Modular Mining Systems concept for scalable and adaptable mining projects 2. Many mining companies have also taken important steps to become more sustainable, implementing measures such as proactive closure strategies, restoration programs and the development of renewable energy projects. In the European Union, laws such as the Critical Raw Materials Act and the Net Zero Industry Act support the mining industry 3,4. They see it as important for the energy transition and promote more sustainable ways of working in the industry Particularly negative environmental impacts such as land degradation, scarcity of local water resources, water pollution and greenhouse gas emissions are ingrained in society’s memory. Despite these efforts, the public image has not yet changed. To change this perception, the industry must strive to better communicate its sustainable practices and the steps it is taking towards a more responsible and sustainable future, promote transparency and build trust.Digitalization, automation and electrification are driving the digital transformation in mining. However, their implementation can lead to higher capital expenditure, limiting their adoption across the industry. Furthermore, implementing new technologies can be a daunting task for any organization. Change management comes into play when introducing such disruptive technologies. It involves preparing an organization for change, potential resistance and establishing effective communication. This helps to ensure that the implementation is successful and the benefits of the new technology are maximized. Digital transformation requires well-trained, young mining, electrical, mechatronic and software engineers with a deep understanding of information systems. Unfortunately, the industry faces the enormous challenge of attracting this younger generation, who have little interest in the extraction of raw materials. The need for action is compounded by an aging active workforce heading into retirement and the forecast of increasing demand for critical minerals.In this challenging environment, the concept of Blue Mining with its constant further developments represents a promising approach. This implies a shift from a linear to a sustainably oriented circular economy. For the mining industry, this specifically means the introduction of innovative technologies, the increased recovery of materials from waste and the consistent questioning and application of circular principles along the entire life cycle of a mine. Such a change can not only reduce the environmental impact, but also contribute to economic resilience and increased social acceptance of mining.

Feb 1, 2025

By Jiongtian Liu, Guixia Fan, Caom Yijun

A cyclonic-static micro bubble flotation column (FCSMC) is an effective separation device for fine grain treatment. The separation of fine ilmenite by FCSMC was explored in this work. The influence of reagents dosage (regulator, collector and auxiliary collector), pulp density, circulation pressure and aeration quantity on TiO2grade and recovery wasinvestigated.The optimal conditions of a rougher are follows: pulp density 45%, pH 5.0, MOH collector dosage 2800 g/t, diesel oil dosage 700 g/t, circulationpressure 0.19 MPa, aeration quantity 0.8 m3/(m2•min). The optimal conditions of a cleaner are follows: pH 4.0, circulation pressures 0.16 MPa, and aeration quantity 0.5 m3/(m2•min).A pilot plant continuous test with a rougher-cleaner by FCSMC for 72 hours was proceeded under the optimum conditions. Compared with industrial flotation machines, the concentrate grade of FCSMC is 48.11% with an improvement of 1.08 percentagepoints, while the recovery is 82.36% with 13.64 percentagepoints increment. Moreover, the flowsheet is simplified from six parts (a rougher-two scavenger-three cleaner) in flotation machines to two parts (a rougher-cleaner) in FCSMC. Proofs were also provided by the analysis of the by-size grade and recovery of concentrate.Results show the FCSMC is an effective separation device to recover -74 µm size fraction.

Jan 1, 2014

By C. Q. Payne

(New York Meeting, February, 1912.) THE art of crushing ores and other materials by means of rolls is a comparatively recent one. While the first record of rolls using iron crushing-surfaces dates back to the year 1806, when they were employed in Cornwall, their principal development has taken place during the last 30 years. To Stephen R. Krom belongs the credit of the pioneer in introducing the belted high-speed roll, which has had its origin and a marked development in this country. His notable contribution to the art was in the use of a single bed-plate or frame supporting the roll-shafts, and to which levers holding the movable roll-bearings were pivoted. He also made use of steel tension-rods to support the crushing-strains, and of hammered-steel tires for the crushing-surfaces. These changes brought the design of crushing-rolls to a high level. Following closely thereon, about 1885, W. R. Eckart conceived the idea of the swivel or ball-and-socket support for the roll-shaft bearings. This is an excellent mechanical conception, especially for bearings held against a spring pressure, and while it may not be necessary for all types of rolls, yet it has been quite generally adopted by other roll-designers, and illustrates the refinement which roll-construction has now reached. Other engineers, as for example, Argall, Vezin, Roger, and Sturtevant, to mention only a few among many, have also given the closest attention to the various details of rolls, such as the frame, springs, bearings, and shafts, and have developed many novel and original designs. It has remained, however, for the boldness and originality of Mr. Edison to extend the field of crushing-rolls in two new directions, and to cause them to exercise new functions. In developing crushing-machinery for his Portland cement works, Mr. Edison constructed ? giant " rolls, having a diameter of 6 ft. and a length of. face of 7 ft.

Jun 1, 1912

By Panagiotis Chryssanthakis

"The aim of this study is to give a better understanding for the performance of the composite material RRS and the synergy effect of its components under different stress regimes and while an excavation face advances during tunneling. The lower part of the Q-system scale (i.e. Q-values of 0.4 or less for a tunnel span of 10m) is commonly used for tunnel applications in softer rock formations. This is implied in the updated Q-chart, where the dimensioning of rock support by using Reinforced Ribs of Shotcrete (RRS) comprises the use of fiber reinforced shotcrete, S(fr), rock bolts and shotcreted beams reinforced with steel rebars. In this study, an effort has been made to simulate RRS in a numerical code and to study its behaviour in a real case study. A double tube, triple lane tunnel in weathered tuff has been chosen as reference material for testing RRS under changing load. A rather extensive parametric study has been run by using the same key input rock mass parameters and three different in situ stress regimes (sH/sv =2, sH/sv =1 and sH/sv =0.5). Changes have only been made to the RRS key input parameters in order to simulate the changing loads during the face excavation process in tunneling. The critical part of this numerical modelling work that is under investigation in this study under each stress regime, is the period just after the excavation: i.e 4 hours; 16 hours after excavation; and finally after the complete curing (28 days) of the cement based components. The RRS are installed in three consecutive numerical steps as follows: a) the application of S(fr) on the rock surface in order to even it up for the RRS application; b) radial bolting; and c) installation of the reinforcing steel rebars, that form the reinforced beam. The results are varying and are strongly dependent on the imposed stress regime and they show in general the following tendencies: The axial forces on S(fr) show that S(fr) is almost overloaded during the first 4 hours in all 3 stages. More particularly: For the case with sH/sv =2 a) the axial forces on S(fr) and on the steel rebars are reduced after 16 hours and 28 days; b) the same is observed on the shear stresses in S(fr) and on steel rebars, they are decreasing after 16 hours and 28 days; and c) the bolts loads are almost unchanged. For the case with sH/sv =1 a) the axial forces on the S(fr) are reduced after 16 hours and 28 days; b) the same is observed for the axial and shear stresses, as well as moments on the steel rebars, they are decreasing after 16 hours and 28 days; and c) the bolts loads are almost unchanged."

Jan 1, 2016

By J. R. Dawson, A. B. Kinzel

THE purpose of testing is to determine whether the material in question is identical in all essential respects with similar material which has given satisfactory service. The most common method of securing such information is to select samples as representative of the entire material and subject them to destructive tests. As the welding industry grew, service data were accumulated and tests of welds took on new significance. New tests were devised and old tests modified so as to be more pertinent to welding. Moreover, in some cases the generally accepted procedure of testing by sampling is not accorded the same degree of confidence when applied to welds as in the usual applications. Thus, in instances where great hazard would be involved should the material fail, means of non-destructive testing have been sought with favorable results. Accordingly, tests used today may be divided into two groups, destructive and non-destructive tests.

Jan 1, 1930

By Dimitrios Polantzas P. E., Collin E. Sweeney E. I. T., Franklin M. Grynkiewicz P. E., Leili Javidanian P. E.

In the latest AASHTO design specifications, the Load and Resistance Factor Design (LRFD) method is prescribed for the design of retaining walls. However, inconsistencies arise when LRFD is used for retaining wall design versus the traditional Allowable Stress Design (ASD). Required toe embedment and wall loading demand vary greatly when the two design approaches are compared, all else being equal. This is due to application of linear load factors to properties that vary non-linearly in the design. These inherent inconsistencies are further intensified when introducing factors such as layered soil profiles, different wall types, groundwater elevation, and surcharge requirements. When applied correctly, these two design approaches, in theory, should lead the designer to the same result with little discrepancy, as they do with steel structure design. However, the use of the current AASHTO LRFD method for various geostructural retaining wall designs yields contradictory results that suggest existing retaining walls that have been successfully designed and constructed are unstable. Fundamentally, LRFD should be built on reliability-based calibrations; the successful past performance of existing retaining structures designed using ASD suggests that the LRFD approach requires considerable modification. The authors of this paper recommend that the current LRFD load factors be reviewed and revised based on more comprehensive wall performance data and wall type such that the difference between retaining structures designed using LRFD and those designed using ASD is eliminated.

Oct 1, 2022

By E. P. Youngman

Tantalum is a rare element ; estimates indicate that there is less tantalum than gold in the earth's crust . After remaining a laboratory curiosity for many years , it was used to a limited extent and for relatively few years (1903- 1911) for incandescent electric-light -bulb filaments . Another wave of interest in tantalum appeared when its electrolytic-valve action was taken advantage of in charging storage batteries , especially for radio work . Tantalum chargers were eventually displaced by other types of chargers , but for a time they were manufac tured in sufficiently large numbers to create a demand for the metal and to bring about its production on a commercial scale in the United States . As tantalum became available in larger quantities and at substantially lower prices , and as high prices for platinum encouraged the employment of tantalum as a substitute , the metal was put to many new uses . Ferrotantalum was made and sold before the World War , and patents have been taken out for a number of special alloys for industrial purposes , but probably the largest use for the metal to-day is in vacuum tubes .

Aug 1, 1930

By H. Pearce, A. E. Lewis, A. Ochieng

Hydrodynamics and mixing are fundamental to the operation of mineral process systems such as flotation cells and metal precipitation reactors. The computational fluid dynamics (CFD) technique has been employed in the present work to study the hydrodynamics in a mixing vessel stirred with either a Rushton turbine or a pitched blade impeller. The multiple frame of reference (MFR) approach has been used to model both impellers. A draft tube was used only in the Rushton turbine stirred vessel. The flow profiles for the pitched blade impeller have been studied in three regions; below the impeller tip, at the middle of the tank, and near the liquid surface. The simulation results were compared with literature data obtained using a laser Doppler velocimetry in the three regions of the vessel, and it was found that the model predictions were better in the impeller region. There was a poor prediction of the experimental results in the region closer to the liquid surface; however, this was improved when the turbulence parameter (C2) in the k-e model was set to a higher value. The value of the impeller clearance at which the Rushton turbine generates an axial impeller type flow has been determined and it has been shown that, at this clearance, a draft tube can be used to enhance axial flow in a Rushton turbine stirred reactor.

Jan 1, 2003

By G. W. Birge

Fifteen coal samples, representing the Winifrede, Chilton, Alma, No. 2 Gas, Powellton, Eagle, Douglas, Sewell, Beckley, Pocahontas No.4, and Pocahontas No.3 beds in Wyoming County, and five samples, representing the Fire Creek, Pocahontas No.6, and Pocahontas No.3 beds in Mercer County, W. Va., were carbonized at 9000 C by the Bureau of Mines-American Gas Association (BM-AGA) method, and yields of products and physical properties of cokes were determined. Expansion characteristics of the majority of samples were determined in the Bureau of Mines sole-heated oven. Chemical analyses and agglutinating values were determined for all coals. The coals were mostly strongly coking and low in ash and sulfur content. Dry, mineral-matter-free fixed-carbon content of the Wyoming County coals ranged from 63.0 to 83.4 percent. The Mercer County samples were all low volatile in rank. Yields of carbonization products were generally in accord with yields from similar rank coals of the Appalachian region. Because of their expanding tendencies, most of the medium-and low-volatile coals would require blending with lower rank coal for normal coke production.

Jan 1, 1965

By R. Mensah-Biney

The loading characteristics of gold-tetrabromide species onto activated carbon have been evaluated using a completely mixed batch reactor system. The overall loading of gold onto carbon was rapid for the first hour but continued slowly without cessation as a result of reduction of gold. Conventional equilibrium considerations were therefore not applicable. Although loading continued slowly after several days, abnormally high loading capacity values of 10-12 meq/g carbon (650-800 kgAu/tonne) could be attained within 72 hours. The loading of gold-bromo species by activated carbon was by the mass transfer of [AuBr4l-onto the carbon surface where reduction to metallic gold took place. Elution of gold from the loaded carbon was feasible provided the carbon had not been loaded to too high capacity values. If loading is carried to high levels, complete elution becomes impractical and the gold may be recovered by ashing the carbon. For the high loading capacities observed, this option would appear to be cost effective. The effect of several variables on the loading capacity of the activated carbon is discussed.

Jan 1, 1992

By AIME AIME

T HE 133rd meeting of the A. I. M. E., opening in New York on Feb. 15, promises to be as successful technically and socially as any in the past. The papers submitted for the various technical sessions are unusually excellent and insure something of interest to every group. Tentative programs have already been issued, and a concise resume of the various sessions, arranged chronologically, appears on page 48. Among the many interesting technical sessions arranged, attention is directed to those of the Petroleum Division, embracing the Symposium on Production that has come to be an annual feature, and new ones on refining practice, transportation and economics. The Institute of Metals program is similarly comprehensive. It includes 15 papers, 8 on copper, 4 on aluminum and its alloys, and one each on magnesium, lead, and fatigue of metals. The Coal Committee offers as a leading contribution its report, prepared under the direction of H. N. Eavenson, giving a new analysis of the capacity of the mines and a comparison of coal with other industries. This will be supplemented by a number of other papers of especial interest to operating men, among which are "Data on Use of Loading Machines in Bituminous Mines," by Graham Bright; "Evaluation of Coal," by R. H. Sweetser; "Selection of Coals for the Manufacture of Coke," by H. J. Rose; and "Relation of Origin and State of Carbonization of Coal to Problems of Low Temperature Carbonization," by S. W. Parr. The Iron and Steel Committee has scheduled seven papers, and there will be a special session on open-hearth practice, in which will be presented the first results of the two conferences, held by the sub- committee at Pittsburgh and Cleveland. A symposium on molding sands will be a special feature of the session on non-metallics.

Jan 1, 1926

By Richard B. Diver, Mark D. Allendorf, Daniel E. Dedrick, James E. Miller, Roy E. Hogan, Andrea Ambrosini, Eric N. Coker, Anthony H. McDaniel, Nathan P. Siegel, Gary L. Kellogg

"Converting carbon dioxide and water to hydrocarbons is an attractive option for storing solar energy and, coupled with appropriate CO2 capture technology, for recycling carbon and impacting atmospheric CO2 concentrations. For any process, high solar-to-fuel efficiency is necessary for large scale viability and favorable economics. Thermochemical approaches for solar-to-fuel conversion are potentially highly efficient as they avoid the inherent limitations of photosynthesis and also sidestep the solar-to-electric conversion necessary to drive electrolytic reactions. Solar-driven two-step metal-oxide-based thermochemical cycles for producing the components of syngas, CO and H2, from CO2 and H2O are the basis of the “Sunshine to Petrol” project. Multi-cycle production of both H2 and CO has been demonstrated over several iron- and cerium-based compositions fabricated into monolithic pieces both in the laboratory and at the National Solar Thermal Test Facility. These compositions are being developed for deployment in a unique and continuous solar-driven reactor prototype, the counter-rotating-ring receiver reactor recuperator or CR5.IntroductionThe interconnected challenges posed by increasing global competition for petroleum and the increasing concentration of atmospheric carbon dioxide are now widely recognized. Meeting these challenges requires recognition that although hydrocarbon fuels are ideal energy carriers, they can no longer be thought of as primary energy sources. It is necessary to take the realistic view that our conventional fossil fuels are in fact “stored sunlight” in the form of “sequestered carbon.” This view leads to a search for options to use and store sunlight more directly.Sunshine to PetrolIn combusting hydrocarbons we unlock the energy for utilization, but we also release the carbon to the atmosphere. However, nature teaches us that with an appropriate persistent energy source, e.g. solar irradiation, it is possible to effectively reverse the combustion process and “reenergize” CO2 and H2O back into hydrocarbon form."

Jan 1, 2010

By K. L. Kayler

The Bardon Trimount, Inc. stone quarry in Ashland, Massachusetts was the recent subject of a quarry closure review report. The quarry produces aggregate using standard drilling and blasting techniques. Stone is processed at an on-site plant. Noise monitoring data collected during the closure review indicate that the quarry generally operates within the quiet range. There is a decrease in noise while the quarry is not operating. Levels of dust associated with the quarry are low. Unpaved roadways are the greatest contributors of fugitive dust associated with the mining operation. The quarry cannot be seen from any homes within the town of Ashland, except during the winter months. The visual impact of the quarry on surrounding properties is minimal. Further quarry development is likely to reduce visibility of the quarry from some areas.

Jan 1, 1995