Search Documents

By T. Ikeda, M. Maeda, K. Mita

Galvanized steel sheet is the major product for the automobile industry. Therefore, automotive recycling results in zinc-containing scrap that should be remelted in EAFs. Naturally, the EAF dust is a very important source of zinc for zinc recycling processes. The thermodynamic properties of the Fe-Zn intermetallic compounds formed on the surface of galvanized steel sheet should be clarified to make clear the evaporation mechanism of zinc; however, there are few reports on these compounds because of difficulties in their synthesis. There are various intermetallic compounds in the Fe-Zn system. We synthesized them at about 673K. A specimen was examined chemically and X-ray diffraction was applied to ensure the formation of intermetallic compounds. Material containing two phases was placed in a Knudsen type effusion cell and the mass spectrum studied to evaluate the vapor pressure of zinc. The thermodynamic property of intermetallics was then evaluated through measured intensity.

Jan 1, 2000

By C. Haycocks

Damage prediction during multi-seam mining is an essential precursor to optimizing mine design. Ground control problems associated with interaction are influenced by both fixed geological and site conditions as well as mining variables which may be controlled to varying degrees. To quantify interaction effects across an affected seam a hazard map approach was selected, which allows interaction data to be presented in a form that can facilitate future planning. Study mines were analyzed using boreholes as sources of geological and spatial data, together with information from mine maps which gives the extent of mining activity. To demonstrate the method the safety factor against interactively caused shear failure in the lower seam roof was computed. Input data included depth of cover, inner burden thickness, remnant pillar size, extraction ratio, immediate roof type, seam thickness, percent sand-stone, and rock strength values. These safety factors were then contoured to produce a hazard map. An assumption was made to assign a high safety factor at the outcrop line to permit realistic contouring of the safety factors. The software also allowed mine workings to be drawn onto the map to facilitate interpretation of the overall results. Hazard analysis permits delineation of unsuitable mining areas within a seam. The application of the method for refining mine design and improving reserve recovery is verified using case studies.

Jan 1, 1992

By Allan Breitenbach

Leaching has been used since the 1600s on unlined ore dumps and since the late 1970s on lined leach pads for the recovery of metals from mined ore, the latter typically called ?heap? leaching and the former ?dump? leaching. Modern day run-of-mine (ROM) or crushed ore heaps are stacked in controlled lifts on lined leach pads and irrigated with a solvent solution (dilute alkaline cyanide for precious meals, dilute sulfuric acid for base metals and uranium). Conventional lined leach pads store process solutions and any storm water, snow melt and cumulative wet season surplus water by gravity flow to external ponds. Impounding valley leach pads (also known as valley fill heaps) differ from conventional leach pads by storing various combinations of process liquid solution and surplus water within internal ponds by using the interstitial pore volume of the ore. While impounding liquids within the heap is simple in concept, impounding leach pads are more complicated for construction and containment compared to conventional leach pads with external ponds.

Jan 1, 2012

6889. Aslakson, C. I., and Swick, C. H. Gravity Observations in Peru and Colombia. Coast and Geodetic Survey,-Special Pub. 233, U. S. Government Printing Office, Washington, D. C., 1943, 18 pp. (Price, 10 cents.) In accordance with the policy of cooperation among American republics, the-United States Coast and Geodetic Survey in 1941 made gravity surveys in Peru and-Colombia. The information was desirable for determining the figure of the earth for geophysical purposes and for studying the relationship between intensities of gravity and deflections of the vertical. The survey instrument was the Brown pendulum apparatus. 11 gravity stations were established in Peru and 13 in Colombia. The results obtained at these stations are given in a table covering observed gravity, theoretical gravity, and anamalies. - V. S.

Jan 1, 1943

By Roger V. Pierce

IN the last few years, much study has been devoted to increasing stoping efficiency. The reasons for this are shortage of manpower, shorter working hours, operating regulations, and shortages of essential materials. More efficiency in mining methods is needed to offset these adverse factors. In the past, attention has been centred upon haulage, hoisting equipment, mill flow-sheets, etc., but recently the spotlight has been focused on the cost of stoping and the cost of handling materials. Scrapers and scraper hoists have thus assumed greater importance. In order to make it possible for certain orebodies to be mined at a profit, it has been necessary to apply assembly-line practices to the streamlining of mining methods. All cycles of the mining operation must balance, and the sooner broken ore is removed from the working face, the sooner another round can be started. Since the introduction of scraper hoists in metal mines more than thirty years ago, much progress has been made in their design and application. Alert operators are now constantly watching for methods in which to apply scrapers. The saving of manpower in development work and the changing of mining methods that once employed manual handling of materials are increasing vital wartime tonnages. Essential ores from newly discovered orebodies are moving rapidly from stopes to reduction plants-because it is now possible to develop an orebody and place it in production with a minimum of manpower and development work. Today, speed is one of the prime essentials o mining. Everywhere, there is a concentrated effort to use experienced miners in breaking rock, in timbering, and in carrying out the various phases of mining that require many months of training. Much effort is being made to mechanize the working places because experienced men naturally prefer to work where the majority of materials are handled mechanically. In line with this policy, many new men are being taught the details of scraper work, because even green men can quickly become acquainted with scrapers and thereby release older heads to perform the more skilled phases of mining.

Jan 1, 1943

By Jorge Cárdenas, Luis Huaroc, Máximo Cari, Nestor Delgado

In Peru, after four years of pandemic, some mining companies have chosen to install integrated operating centers in central offices where through network technology and video surveillance it allows them to carry out their activities remotely, this has become a disruptive strategy to promote a safer and smarter mining industry. Our fundamental value is to improve the quality of life, safety and well being of our collaborators, that is why we have created the remote blasting engineering control center " Core" that allows us to humanize mining. Core is an integration of experience, security, technology, quality of life and artificial intelligence; it has media technology connected directly to the mining operation, specialist engineers and technical assistants in team they seek to create optimal proposals of drilling and blasting designs remotely that generate added value to customers. In the planning process the team suggests drilling meshes, in the loading process there are optimized, digitized designs and efficiency in the factory trucks finally in the safety process allows us to identify inadequate pipes within the blasting project, deviation of procedures, remote inspections, identify operating conditions to prevent future risks that may arise in the blasting process. The remote communication systems allow you to monitor mining operations remotely to identify and alert any operational or security deviation that was not identified by the personnel present in the operation, as well as to store images in case investigations are required. The results obtained have allowed us to reduce the exposure of personnel to any risk of the mining operation, to optimize times in the activities of our engineers who are in the mining operations since there is the permanent support of centralized specialists to face every challenge that arises in the operation, for the engineers who are in the offices of Core can be very close to the family and do not lose it, and for our customers it is to meet their needs with engineers specialists in the drilling and blasting process, as well as in safety to be able to proactively cope with any deviation that arises.

Jan 21, 2025

By Donald R. Reichmuth

Most brittle solids are relatively weak in tension and this weakness can be very significant in determining their performance in structures and excavations. Consequently, accurate knowledge of the tensile strength of brittle materials has long been recognized as important. In the past, measurements of the tensile strength of materials such as concrete, ceramics, and particularly rock have been hindered by problems encountered in fabricating test specimens and in accurately loading them. These difficulties have resulted in a scarcity of published tensile strength data. This can be readily seen in tabulations such as Wuerker's "Annotated Tables of Strength and Elastic Properties of Rocks."1 There are now three distinct approaches being used to determine the tensile strength of brittle materials. These are shown schematically in Fig. 1. The first method consists of simply pulling the specimen apart by applying an axial load. Although this procedure is the easiest to understand, the technical problems encountered during testing are numerous. Specimens cannot be readily fabricated into dumbbell-shaped specimen* like those customarily used for testing inetals. Cylindrical specimens cannot be loaded in jaw-clamps because adverse stress conditions arise at the clamping points, which causes unreliable results. An innovation developed by Niles Grosvenor at the Colorado School of Mines, in which the load is applied through steel-end caps glued to the ends of the specimens, has considerable merit, hut the samples are costly to prepare.2 All tests using a direct pull are further handicapped by the possibility of small amounts of bending being present, the specimen's surface condition, and

Jan 1, 1968

By P Hagan, S Campbell

A study was undertaken using various methodologies to determine the optimum loading and hauling configuration for different haul routes at Callide Mine, a coal mine located in central Queensland. The study involved development of an effective flat haul model that was used to estimate production rates in truck and shovel circuits that employ two excavators of differing capacities then Queuing Theory to construct a capacity constraint model for scheduling purposes to assist in truck allocation and finally a cost model to determine the most cost effective fleet configuration.The model was calibrated using haul road design and performance data of trucks and excavators currently in use at the mine. The study examined the effects of cycle time for different truck and excavator fleet configurations on production rate and costs.The study found haulage cost was directly related to cycle time while production rate reduced with cycle time. The study indicates the approach taken in combining a cost model with a capacity constraint model offers a simple and effective method of scheduling an optimum number of trucks in a haulage circuit.CITATION:Campbell, S and Hagan, P, 2012. Selection of an optimum truck and shovel fleet based on effective flat haul and capacity constraint modelling, in Proceedings Eighth Open Pit OperatorsÆ Conference , pp 19-26 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 18, 2012

By E. K. Kleespies

The rate of the heterogeneous reaction between titanium-oxygen solid solutions and titanium trichloride in molten sodium chloride was determined at high temperatures. In the alpha phase, the reaction rate decreases uniformly with the increasing concentration of oxygen. The gamma crystalline form of titanium (above 33 atomic percent oxygen) was much less reactive than the alpha phase, and the reaction rate approached zero at 50 atomic percent oxygen. The activation energy for the reaction of titanium-oxygen solution containing 22.8 percent oxygen was 11.7 kcal/mole of TiCl3 as compared with 8.3 kcal/mole of TiCl3 for pure titanium.

Jan 1, 1967

The Mount Whaleback iron ore deposit at Newman, Western Australia comprises the largest known continuous iron ore deposit in Australia, originally with a Measured Resource in excess of 1700 Mt of hematite ore. The deposit occurs within the Hamersley Province which forms part of the Pilbara Block in the NW of Western Australia (Figure 1). The Mount Whaleback iron ore deposit, together with a number of discrete iron ore bearing satellite orebodies in the Newman district, contributes to the Newman Lump and Fines products. Extensive quality control systems are utilised from mining to shipping to ensure that each product meets a narrow geochemical target grade range.

Jan 1, 1997

This publication summarizes the research (in-house and contract projects) programmed by the Bureau of Mines for fiscal year 1985 (October 1, 1984-September 30, 1985) under its Health and Safety Technology Program. The objective of these projects is to provide an ordered and sequenced advance toward the Bureau's overall goal of providing the system technology required to create a more healthful and safer working environment for the Nation?s mining and minerals processing workers.

Jan 1, 1985

By Homor N. McDonald, G. Dale Coe, Will H. Coghill

"INTRODUCTION Sporadic beneficiation tests have been made on the Birmingham (Ala.) red iron ores for the last 55 years. Now, gravity-concentration plants are in operation, of tables are in use. A major problem, as seen by the present writers, is to obtain a coarser concentrate and add to the recovery without increasing the quantity of slime. The oily practicable solution found so far is to recover, by means of concentration (hydraulic) classifiers, the coarse concentrate normally lost in the table middling and, by a similar method, to recover middling particles from the table tailings The size and shape of the coarse concentrate Particles combine to cause them to report in the table middling rather than in the table concentrate. Similarly, mineral is lost in the tailing. Because of this, the nature of the ore, the deportment jerking table, plant tests on classifiers and tables, and the suitability of small concentration classifiers to treat table zonal middlings are discussed herein.The work was done by the Southern Experiment Station, Bureau of Mines, in cooperation with the University of Alabama, Tuscaloosa, Ala."

Jan 1, 1935

By John Fitzpatrick

In this Bureau of Mines investigation a device was developed that permits the determination of the modulus of elasticity of the stress-relief cores obtained in the process of making in situ stress measurements. This determination is made by hydraulically loading the external surface of the stress-relief cores and by measuring the corresponding borehole deformation. The theoretical relationship between the borehole deformation, the applied pressure, and the modulus of elasticity is presented. Also, experimental results obtained from measurements on a simulated stress-relief core made of aluminum and on a limestone stress-relief core are given. Because of the symmetrical loading obtained with this device, the isotropy of the core material can be evaluated. With this device it is also possible to study the effect of eccentricity, that is, the effect within cores in which the inner hole is not coincident with the long axis of the specimen.

Jan 1, 1962

By MacDonald W. L. F. C. A.

IN accordance with the usual approach to a participation in a panel discussion, this paper is, in some respects, intentionally controversial. I would suggest, how-ever that there is more than a grain of truth in many of the comments made. Before dealing with a particular problem. It is appropriate to set out a few of the more significant objective of an: accounting system: (1) The provision of historical data <•concerning past events, for the information of shareholders, tax authorities, etc. This data can also be used as a tool to predict the future. (2) The provision of a record to safeguard the company's assets and to form the basis of any claim for insurance or other damages. (3) The provision of an accounting framework in making an economic study of a proposed course of future action such as the development of an orebody or the outlay of a substantial sum for new equipment. ( 4) The

Jan 1, 1962

By Stavros A. Argyropoulos, Henry H. Hu

"The assimilation of exothermic additions in liquid metals exhibit an array of unique coupled heat, mass and momentum transport phenomena. These phenomena are further complicated by the presence of a moving boundary.This paper describes a) A mathematical model which simulates the complex phenomena, and b) An extensive verification of the mathematical model. The SIMPLER algorithm was employed to solve numerically the pertinent partial differential equations. The computational results indicated that the exothermic heat of mixing led to a rapid increase in temperature around the moving boundary, which produced an enhanced convective flow in the liquid phase. The intensification of fluid flow around the moving boundary resulted in an acceleration of the melting process.Verification of the model was carried out in two contexts. The first was, in a low temperature physical model consisting of ice immersion in different sulfuric acid solutions. In this physical model, both temperature and velocity measurements were carried out. The model results were compared with experimental measurements and they were found to be in excellent agreement. The second context employed high temperatures, involving the assimilation of silicon in high carbon liquid iron. The model was also applied to predict fluid flow, heat and mass transfer for these high temperature experiments and a good agreement was obtained.In addition new dimensionless heat transfer correlations that quantify these complex phenomena will be presented."

Jan 1, 2001

By A J. Jonaitis

The DENVER Tube Press is a simple, high pressure (1500 PSI (100 bar» filtration unit, developed for processing difficult-to-dewater materials and to produce a handleable filter cake and clear filtrate product. Lab and pilot testwork conducted in Australia on coal fines (55-70\ -35 micron (400 mesh)) have shown that total moisture contents of less than 20\ are consistently achieved in the final cake products from the Tube Press. Currently, these coal super fines are sent to waste due to uneconomical mechanical dewatering methods, which were only able to reduce total moisture levels in excess of 30%. Calculated, throughput rates for the 500 Series Tube Press exceeded 1700 kg/hr (3750 lbs/hr). Feed solids concentration requirements are between 45 and 50\ to achieve these results.

Jan 1, 1993

By D W. Evans

Research into the dynamic properties of ground support elements continues to grow at a global level, given the increasing importance of this field of application within underground hard rock mining. Measuring the mechanical response of such elements under the rapid onset of simulated rock burst loads forms the basis for this experimental work, typically utilising gravitational drop testing methods. This field of research is fundamentally driven by an increasing need for dynamic performance data, given the constant evolution of rock bolting product designs, materials selection, combination testing and specific application needs based on ground types and loading scenarios. A smaller number of globally recognised dynamic test facilities have predominantly lead research within this arena, typically in association with academic institutes, larger industry groups and government research institutes. However, due to the increasing requirement for dynamic performance data, additional facilities have now emerged in order to satisfy the overall demand for test work. These newer facilities are more typically associated with suppliers to the underground hard rock industry, with experimental designs looking to replicate, at least in part, the work of the primary facilities. For standardisation, repeatability and calibration purposes, the cross validation of test data between primary and secondary facilities becomes an obvious and important consideration across this field of research. This paper outlines the development of a new dynamic drop test facility for testing rock bolts, including the structural design and associated high speed data capture system. Based on the utilisation of identical bolt types, material grades, anchoring systems and decoupled ‘free-lengths’, comparative data has been generated to provide cross validation of the new test facility against data generated by a globally recognised primary facility. The cross validation of data provides increasing confidence in the repeatability and accuracy of the new facility as activity continues towards the provision of further experimental test work.

Nov 29, 2022

By Mike Broczkowski, Laura Dewhirst, Kieran Large, Angelo R. Fernando, Heather Daigneault, Jim Johnson, Randy Wiens

The radioactive isotope radium 226 is a contaminant of potential concern in effluent waters from metal mining operations in Canada. Acceptable release levels of radium 226 are governed by Metal and Diamond Mining Effluent Regulations. Since radium is invariably present as a companion element in uranium ore, monitoring and controlling of radium 226 is a must for uranium mining operations. Measurement of radium 226 is traditionally carried out through a radiochemical technique involving selective co-precipitation of radium with barium sulphate followed by alpha spectroscopy for quantification. As of 2010, Cameco has also been using an ICP-MS based radium analysis method developed in collaboration with a research team at Trent University, Peterborough, Ontario. This method, which is highly automated and requires significantly less sample handling, with improved turn-around-times, is being used by Cameco site laboratories at the McArthur River and Cigar Lake mines as well as the Port Hope Conversion Facility. This paper compares the benefits and drawbacks of this new method, compared to the traditional alpha counting procedure drawing from almost ten years of field experience.

Jan 1, 2020

By A. J. Davidson

A novel sensor is described for the measurement of the copper content of copper matte. Due to the high copper concentrations found in matte, potentiometric sensors are not sufficiently sensitive. A highly sensitive sensor has been developed based on a modification of the amperometric technique using a copper ion conductor, Cusicon. The results correlate closely with the theoretical predictions.

Jan 1, 1998

By B. Denby

Recent advances in Virtual Reality (VR) technology have resulted in major opportunities to improve safety training of mine workers, supervisors and managers. The hazardous nature of both surface and underground environments limits the type of safety training that can be carried out. VR offers the potential to expose mine personnel to hazardous situations in a safe, highly visual and interactive manner. Customized simulations of mine layouts, dynamic operations and mine environment can be set up and mine personnel can be allowed to move around the virtual mine, making decisions at key points. The consequences of both correct and incorrect decisions can be immediately fed back to the trainee.

Jan 1, 1998