Search Documents

By W. S. Ayres

A BRIEF history of the growth of the anthracite-coal preparation will give a better view-point from which to judge the present problem of separating slate from coal. At the beginning of the commercial value of anthracite, 70 years ago, only the pure portions, or " splits," of the veins were mined and shipped to market, and without any preparation or screening other than the selection, while loading, of the glassy lumps, and the rejection of the fine material and the slate that had strayed accidentally into the coal. The next step was the crushing or breaking of the coal (hence the name Lt breaker" as applied to the preparation-building), and the sizing of it by means of bars or revolving screens. This stage of its development marked the advent of the "breaker-boy " as a slate-¬picker, with his ever-increasing capriciousness. As the richer veins or ? splits " became exhausted and the market demanded a still greater output, the less-pure " splits " and the thinner veins were utilized to produce the coal. Carrying as they do a far greater percentage of impurities; particularly when removing the pillars, it became necessary to build new and better equipped preparation-plants. Finally, we are now at the highest stage of complication yet known to the art of coal-preparation. We are dealing with varying specific gravities, frictional difference, hardness, structure, and form in the pieces of coal and slate coming from many different veins, and

Dec 1, 1909

By S. J. Lui

Sodium oleate was an effective diaspore collector, whereas chelate collector OL2 showed certain collecting power over diaspore and nonionic surfactant OL3 showed little collecting ability. Then experiments were carried out using sodium oleate as the main collector with the addition of OL2,OL3 to study the influences on diaspore flotation, it could be seen from the experiments that accelerants had a marked influence on the recovery of diaspore, which could be raised by 10%, and the addition sequence also affected the flotation behavior: the best results could be gained when the accelerants were mixed thoroughly before adding and the best ratio of collector OL1 and accelerant OL2, OL3 stood at 30:2:1. Based on the calculation of the ingredients in the sodium oleate solution, sodium oleate reacted with surface of the mineral and formed the acid-soap polymer [HOl?Ol-] when pH was about 9. Zeta potential test showed the accelerant promoted the absorption of collector on the mineral surface, which lowered zeta potential. As could be seen from surface tension experi-ments, the addition of accelerant OL3 lowered the CMC value of OL1 solution, which was equiva-lent to raise the power of the agents. Further Infrared Ray experiments showed the co-absorption of OL1 and OL2 make aluminum oleate on the mineral surface more stable. Up till now, the mixed reagents with sodium oleate as the main collector, combined with other two accelerants had been used in the Zhongzhou concentration plant, which is the first diaspore flotation plant in China.

Jan 1, 2014

By H. R. Pierce

A gas well has a certain definite capacity to deliver gas from the gas sand through the producing string of pipe. This capacity depends upon the pressures in the sand; that is, a well will deliver gas at a rate of flow which is determined by the formation or "shut-inn pressure in the sand and the back pressure at the face of the sand in the well. The three factors, rate of flow, formation or "shut-in" pressure, and the back pressure, for a given well, can be written into a fundamental relation which is strictly applicable only to that well. This relation can be used to determine the capacity of the well to deliver gas from any formation pressure against any back pressure held at the f ace of the sand in the well. Studies have been made of the deliveries of 400 gas wells operating under different conditions of pressure, Most of the wells which have been studied are in Osage County, Okla.; however, several representative studies have been made on wells in southern Louisiana, southern Texas, the Texas Panhandle, and West Virginia.

Jan 1, 1929

By LUDWIG VOGELSTEIN

WE are indebted to Mr. Barbour for his valuable contribution to the literature on copper statistics; it is to my knowledge the only intelligent attempt to throw light on a much misunderstood subject. If I should appear to criticize some of his findings and arguments, I do not want to leave the impression that I do not appreciate the article; I think Mr. Barbour has been painstaking, and even where one might not agree with his conclusions, he has opened our eyes and stimulated us in our search for the truth.' It might be well to define the term "secondary copper" and to make a few remarks about the origin and the reasons for the variation of the supply. Mr. Barbour has touched on these points, but not sufficiently to make them clear to those not in the business.

Jan 1, 1931

By David C. Kraft

Helical piles and ground anchors were used to meet critical design and constructability requirements for an urban forest Canopy Walk at the Atlanta Botanical Garden, Atlanta, GA. The 12-foot wide pedestrian walkway path was to be nestled among the treetops of a forest, extending to 600 ft. in length, and soaring 40 ft. high above the forest floor. Of particular concern during construction was that the foundation system for the temporary steel shoring system had to be non-invasive to the subsoil, could not damage the forest floor, trees, root systems, or foliage, and upon completion of the concrete walkway pour, could be removed, again without disturbing the subsoil. Accubrace, Inc. designed and installed all the helical foundation types, as well as provided steel braces, typically used in Tilt-Up building construction, for the walkway project. The braces, some extending to 43 ft. in length, were used to provide lateral support against wind loads for the walkway form. In addition, the braces acted as secondary support for lateral loads during the placement of wet concrete along the 600 ft. length of the walkway. Helical foundation products installed included vertical compression piles, ground anchors for tension rods, and ground anchors for the braces. The installation of the piles and anchors was particularly challenging since the forest floor elevation varied as much as 50 ft. due to the presence of a ravine. Information is provided on the subsoil conditions, required loads, design, installation, and acceptance criteria for each helical product type installed for the project. The results of vertical and lateral load tests on the helical piles in the pre-construction phase, conducted in conformance to project specifications are presented. Photographs to illustrate the nature and complexity of the project are included. The concrete pour for the walkway was successfully completed on December 12, 2009, and the walkway was opened for visitors in May, 2010.

Jan 1, 2011

By G. R. Hopkins

According to reports received by the Bureau of Mines, Department of the Interior, as of January 1, 1934, there were 591 completed refineries in the United States, an increase of 86 ever the total reported at the beginning of 1933 and the largest total ever recorded. It should be noted that the 1934 total, although large, probably does not include more than half of the "pot-still" plants of 1 barrel to 50 barrels daily capacity which have sprung up within the last 2 or 3 years and about which very little information is available. However, the combined operations of these snail refineries are of negligible importance as altogether they refine less crude than one plant of average size. Of the completed plants, 454 were operating on January 1, 1934 and 137 were shut down. In addition, 13 refineries were under construction on January 1, 1934. Compared with the previous year these data indicate a marked increase in the number of operating plants, little change in the number of inoperative plants, but a decline in' the number being built. The material gain in the number of operating plants resulted primarily from the construction off approximately 25 refineries, averaging about 100 barrels capacity in the Kooky Mountain district, as well as from the addition of about 20 plants in the East Texas field.

Jan 1, 1934

By Curt D. Edgerton

This study was made to determine trends in fresh water usage by California petroleum refineries, to forecast fresh water requirements to 1975, and to evaluate water conservation practices. Statistical data used in the study were obtained largely from published sources and from records of selected companies. An adequate sampling of the State's refining capacity was obtained, and the data were extrapolated to the total California refining capacity. A breakdown of the data was then made on the basis of the following refining regions: (1) the Los Angeles Basin and Southern Coastal region, (2) the Southern San Joaquin Valley, and (3) the San Francisco Bay area. An unpublished forecast of crude oil input to refineries by a major oil company operating on the West Coast was used as a basis for predicting fresh-water usage. The 1963 fresh water intake by California petroleum refineries was 84 million gallons per day. This is expected to increase to 128 million gallons per day by 1975. The fresh-water to crude-oil ratio is increasing in all regions except the Southern San Joaquin Valley. At present, the supply of fresh water available to almost all of the State's petroleum refineries, mostly from surface sources and company-owned wells, is adequate, although shortages may develop within the foreseeable future. Present conservation methods are centered around the following four objectives: (1) minimum intake of fresh water of the lowest possible quality commensurate with sound technologic practice; (2) optimum recirculation; (3) proper treatment before discharge; and (4) substitution of air cooling for water cooling.

Jan 1, 1965

By Chenyang Zhang, Zhigang Yin, Jianyong He, Yuehua Hu

"A lot of floatation reagents (collectors, inhibitors and regulators) for the beneficiation of copper ores have been well developed in the past century. However, it is still unclear about the micro interaction mechanism of these flotation reagents with copper ores. In this paper, the interaction mechanism of these flotation reagents with the copper atom on chalcopyrite has been systematically investigated by first principle DFT (density functional theory) calculations. Thirty-four specific common functional groups linked with the same hydrocarbon chain (ethyl) are optimized at a B3LYP/def2-TZVP level, the solvation effect was included with the SMD solvation model. The analysis of the highest occupied molecular orbital (HOMO), the lowest unoccupied molecular orbital (LUMO) and nature bond orbital (NBO) charge of these reagents reveals their potential applications to other types of copper-bearing mineral. Further investigation of the thermodynamics calculations gives more reliable data to screen collectors or inhibitors for copper-bearing mineral. The flotation results from carefully reviewed literatures are in good agreement with the calculation results. This work might also shed new light on the development and discovery of highly efficient and selective flotation reagents with low cost based on the computational methods.INTRODUCTION Froth flotation,(Shean & Cilliers, 2011) a mineral processing approach, is applied to efficiently enrich valuable minerals from the mixture, which is achieved according to the dictinctive surface properties of minerals. In the past century, researchers have develped an aboundant of flotation reagents by extraction or synthetize, and many carefully selected reagents might die in the bench tests or the pilot tests before the pratice.(Bulatovic & SrdjanM, 2007) Generally, it involves a lot of cost and tedious works by conducting flotation tests to screen flotation reagents. Flotation reagents have been boomed robustly with the developing of the organic synthesis.(Liu, Yang, & Zhong, 2017) Reseachers found the specific properties of a reagent are determined by its functional groups and the length of the hydrocarbon, where the functional group is assigned as the adsorption site to adsorb onto mineral surfaces and the hydrocarbon chain is called as a hydrophobic group."

Jan 1, 2018

By Charles Legrand

The power plant of the Burro Mountain Copper Co. is located near Tyrone, N. M., at 5,950 ft. elevation. It is interesting because it uses the largest stationary Diesel engines in the United States. The general layout of the plant is shown in Figs. 1 and 2. The building is of steel-frame construction with hollow-tile walls and corrugated-iron roof; the floor is concrete and all windows have steel frames, making a fireproof building. The building is made to accommodate one more electric generator unit which is being installed; also two 4,000-cu. ft. air compressors direct-connected to three-cylinder engines with the same size cylinders as the electric units. The power plant consists of two 815-kva., 60-cycle, three-phase, 6,600-volt, 180-r.p.m. generators, direct-connected to five-cylinder, two-cycle Diesel engines; the necessary circulating pumps for cooling water, cooling towers and oil storage tanks. A portion of the power is used in the same building as the generating units to run one of two 200-kw. rotary converters delivering 260-volt direct current, and a 2,500-cu. ft. air compressor, delivering air at 95 lb. pressure, direct-connected to a 400-hp., 6,600-volt, three-phase synchronous motor. The remainder of the power is used to run a 1,500-ton concentrating mill 3 ½ miles from the power house, various hoists, pumps and motors about the mines and the lighting and water-works of the town of Tyrone. The direct current is used for electric traction in the mine, also to run hoists and motors that were installed before the new power plant was built. Due to the large hoists that take starting peaks of 250 kw. and the 10-ton electric locomotive that takes at times 150 kw., the load is extremely variable, as shown in. Fig. 3.

Jan 9, 1916

By D. W. Frommer, M. M. Fine

"INTRODUCTION Laboratory mineral-dressing investigations covered by this report show that ores from Montgomery County, Ark., and Morgan County, Mo., are potential sources of barite and zinc. Fine grinding and froth flotation yielded drilling-grade barite from the former and chemical-grade barite and zinc concentrates from the latter.Samples from these deposits were subjected to a laboratory investigation to develop an economic and feasible treatment. The Arkansas ore, submitted by the Husky Refining Co., consisted of an intimate mixture of the economic mineral and quartz. Fine grinding and fatty acid flotation were utilized to effect a good recovery of a drilling-grade product. The other was a zinc-barite ore submitted by the Rocky Ford Mining Co., Stover, Mo. There was no problem in the recovery of zinc (most of which occurred as sphalerite), but the recovery of barite by flotation was complicated by the presence of gangue carbonates. Ultimately, an excellent recovery of barite was achieved with a relatively new type of flotation promoter, petroleum sulfonate.In recent years, barite has become one of the major industrial minerals as an essential ingredient in heavy drilling fluids, pigments, and chemicals. New sources of this important commodity are always interesting; thus, it is the purpose of this report to present information that may permit commercial exploitation of two deposits not in production."

May 1, 1952

By H. Rush Spedden

A process has been developed and piloted to reject copper, lead, iron, phosphorus, bismuth, antimony, elemental sulfur, and insol from molybdenite concentrate without decomposing the contained molybdenite and rhenium. The impure concentrate is first heated with concentrated sulfuric acid at 260 to 290°C for 1 hour. This bake not only oxidizes the contaminating sulfides, but also activates the concentrate for later rejection of insol by flotation. Two stages of leaching follow the sulfation step. The first is an acidified water leach which extracts the oxidized copper, iron, and phosphorous; the second leach rejects the lead, bismuth, and antimony into a warm concentrated solution of sodium chloride. Final upgrading is achieved by conventional froth flotation. The chemistry of the process as well as results obtained from its implementation in a 5,000 lb/day pilot plant are presented.

Jan 1, 1971

By Hewitt Wilson

[ ]

Jan 1, 1927

By B Hall

The authors have undertaken many independent mine optimisation and operational improvement projects at Australian and international mining operations over the past decade. This work has provided an understanding of the underlying practices responsible for the good long-term performance of some operations, and the failure of others to achieve their objectives. Good long-term performance, and value creation can be achieved through a logical and rigorous process of identifying the optimal mine plan (æThe PlanÆ) that delivers the corporate goals, establishing appropriate performance measures that are aligned with these goals, and ongoing monitoring of compliance with the established targets to ensure the operation reliably achieves The Plan. A number of practical methods have been developed and implemented to assist mining operations deliver their corporate goals. This paper outlines some of these methods, providing some fundamental guidelines that will assist in the establishment, and reliable achievement of The Plan that delivers the corporate goals.

Jan 1, 2006

By F. G. Miller

[Petroleum technoloF;istz and 1 rot-re s s ive OT e:?ztors. con stantl;, are striving to increase the percentage of oil that y to recovered from reservoir rocks throe::;:: wells. The exhaustive studies that have been made of the function of natural r:; as in t h-_ T r odI action of oil, for cx<n.mTnle, have aidedd of.erators greatly in incroasin,&apos; the q-:Arrntity of oil recovered from reservoirs. i.rtural gas dissolv3d in ar--d otinerwwisa &apos;1s&apos;.,ocintjd under rre3suro with oil in roscrvoir roci.s, howover, i:; not the only source of energy available for moving oil through sa&apos;:&apos;l to wells. l becoming "reservoir-energy conscious&apos;t engineers hr-vo -d o^.rued t}:-Lt in many petroleum reservoirs the edgewater flanking t -,e oil accum.-,lation conetitutos a potential source of onergy capable, tL-ou;_h rro? gr control, oil&apos; increasing oil-recovery efficiencies materially. i o ]enter is ti-.-,, on-cronchinunt of water into the oil- and gas--fillod ?art of the reservoir considered as an evil to be combatted by devious mot&apos;:r:ci :i,.t r,ttL er a natural conseque::c4, incident to the withdrawal of oil nna gas from the wells, that nay be T.usod advantrt eou ;ly in lonr`t}toning tr e r&apos;lowin g lift of wells a.nd, i norcas in:; the economic recovery of oil and Little is known about the by which water off: oratos in driving nil throe:gh reservoir roc:-.:,, nd i:. a scorcity of rubli:;Lad informs-¬t .on nn rates of :)Ov.:m.,:- t of : r.tcr ..at v:1:11 res,-_lt in ^r i-nu oil recoveries. Bureau of :fines engine_:? ; - reciate. the r,aucity of scientific knowledge or. the &apos;test methods of a,r.lying the natural water arive to in¬crease oil-recovery efficiencies ant ,i.;?l __-itir?,~ ting irties that will, they hope, Contribute to t.1&apos;.e T ros?Jr.t. small _ %nd of information now av tilable on tt:e cubjoct. This r».crt a oyno-.::is or brief comrilnt.ion of r,ublished data and thought accuinulnt.~d so far, to la)or;~.tory ox-:erimnntrr¬tiorn and, further rosoarch on the z_rrinciplos unri;rlyir..g the natr.rr+1 eater drive no it nffocts oil recovery. :Lie writer:: Lore that t.i.c cx-nositiorn of a?rzilable inforr-at ion i rcs?r.toi in the rernrt r .-II .i ,.1rtt cor_jt_-i:ctive tho.-_.I_t and efforts loadir,-z to -:ard more con.r .ote extraction n;&apos; o tl from reservoirs.]

Jan 1, 1938

By T. F. Tomb

on&apos; January 6, ,1992, the Mine Safety and Health Administration (MSHA) issued an Advanced Notice of Proposed Rule Making (ANPRM) for diesel particulate (DP). The ANPRM identified five areas where the Agency was seeking additional information to assist in the rule making process. These areas were exposure &apos;limits, risk assessment, consideration of other information, sampling and monitoring methods, and feasibility. The period for submitting information relative to the ANPRM closed July 10, 1992. Prior to issuance of the ANPRM, the agency was involved in conducting studies to evaluate sampling and control technologies and to gather information with respect to occupational exposures to diesel particulate in underground mining operations employing diesel-powered equipment. Since issuance of the notice, additional studies have been conducted to provide supplementary information in these specific areas. Results of these additional studies indicate that average DP levels in coal mines not using aftertreatment range from 0.9 to 2.1 mg/m3. Aftertreatment devices can reduce these levels by approximately 50 to 90 percent. Studies conducted in metal and nonmetal mines showed average DP levels ranging from 0.3 to 1.6 mg/m3.

Jan 1, 1994

By R. T. Artz, Simpson. O. V.

"INTRODUCTION The provision of escapeways from coal mines is a moral and, in most States, a legal obligation of mine owners and operators. The obligation is not always fulfilled because of the hope that no occasion will ever arise requiring the use of such facilities, and, as time passes without the need for using them, a false sense of security is born in the belief that ""it can't happen here.""The disastrous fire in a mine in Ohio on July 5, 1944, again focused attention on the importance of escapeways in averting disasters and made it clear that one or more dependable exits must be provided from a mine and parts thereof where men might be trapped by being cut off from the regular travel route. This matter of always-having available travelable exits has been advocated for many years by the United States Bureau of Mines."

Aug 1, 1948

By H. G. Warrington

Abstract As part of the active development programme pursued by Dominion Magnesium Limited since 1945, a modern extrusion plant was erected and has been in operation for about twelve months. The only source of nigh purity magnesium in the world, Canadian metal is produced by metallurgical processes within the frame-work of the mining industry, which gives a different viewpoint to every phase of production from other world suppliers of commercial grade metal whose operations are based on chemical industries and techniques. The superior properties of corrosion resistance and grain refinement have aided a programme of standardization, reducing the number of alloys supplied in extruded form from seven to four as an aid to economic production. The first big step was the development of a general purpose alloy known as AZ?21x covering all decorative and medium stressed applications, which will supersede two older alloys. Sales approaching a million feet in this alloy show that it bids fair to become the &apos;mild steel&apos; of the magnesium industry, its applications ranging from terrazzo floor strip to textile machinery and television mast components. In the high stressed field, metallurgical features preclude low-cost extrusion of the older high-strength alloys, but recent development of a magnesium alloy containing zirconium promises an easily workable metal. Hitherto produced by expensive chemical additions, research now shows that the alloy can be produced by metallurgical means, which may make this alloy available for a wide range of commercial applications. Thus the future development programme for extruded products in the form of tube, bars, shapes, and structural angles and channels may evolve two alloys to cover all applications for strengths up to 52,000 lb. per sq. in. Such standardization is the result of taking advantage of the physical and metallurgical properties of high-purity magnesium instead of accepting techniques based on metal produced by older processes.

Jan 1, 1951

By Curt D. Jr. Edgerton

This study was made to determine trends in fresh water usage by California petroleum refineries, to Forecast fresh water requirements to 1975, and to evaluate water conservation practices. Statistical data used in the study were obtained largely from published sources and from records of selected companies. An adequate sampling of the State&apos;s refining capacity was obtained, and the data were extrapolated to the total California refining capacity. A breakdown of the data was then made on the basis of the following refining regions: (1) the Los Angeles Basin and Southern Coastal region, (2) the Southern San Joaquin Valley, and (3) the San Francisco Bay area. An unpublished forecast of crude oil input to refineries by a major oil company operating on the West Coast was used as a basis for predicting fresh-water usage. The 1963 fresh water intake by California petroleum refineries was 84 million gallons per day. This is expected to increase to 128 million gallons per day by 1975. The fresh-water to crude-oil ratio is increasing in all regions except the Southern San Joaquin Valley. At present, the supply of fresh water available to almost all of the State&apos;s petroleum refineries, mostly from surface sources and company-owned wells, is adequate, although shortages may develop within the foreseeable future. Present conservation methods are centered around the following four objectives: (1) minimum intake of fresh water of the lowest possible quality commensurate with sound technologic practice; (2) optimum recirculation (3) proper treatment before discharge; and (4) substitution of air cooling for water cooling.

Jan 1, 1965

By Rob Domotor

This paper tells the story of using controlled surface and underground blasting methods to excavate hard rock in three areas on Australia’s largest road infrastructure project; the Airportlink Project in Brisbane; worth a total value of AUD $4.8 billion. The project used blasting methods including design, modelling, drilling and loading of the explosives that had never been used before in Australia, some of these were probably unique in the world.

Jan 1, 2012

Mine managers need better information to locate new opportunities and then to assess the effect of their decisions. We are developing the Intelligent Decision Support System (IDSS) and its two major modules, the Pattern Recognition System (PRS) and the Knowledge Representation Subsystem (KRS) to automatically provide the information from monitoring system sensors. This paper focuses on the KRS Algorithms that extract key information from lists of time study type event sequences. Because a static system cannot operate effectively in a dynamic mining environment, we are prototyping an index based technique that allows the system to adapt itself to this dynamic environment.

Jan 1, 1990