Search Documents

By G. F. Colborne, A. Thunaes

"When the Canadian uranium milling plants went into operation during the early 1950's, they utilized flowsheets developed at the Radioactivity Division of the Federal Mines Branch in Ottawa. Since then, numerous process improvements have been made by the Mines Branch, by the operating companies themselves and by other research organizations. This paper will consider uranium milling technology from the standpoint of a new mine operator charged with the responsibility for the design of an economic flowsheet, and will indicate the range of process elements available to him and the testwork required to enable an intelligent decision to be made."

Jan 1, 1968

By Stanley W. Ivosevic

The South-Central area of the Osa Peninsula, Puntarenas Province, on the Pacific coast of southern Costa Rica, may have produced on the order of 30,000 kg (100,000 troy oz) of gold since prehistoric times. The Peninsula lies along an 800- to 900-km-long belt of late Mesozoic eugeosynclinal rock deposition, hydrothermal activity, and deformation (Campanian). The oldest rocks exposed in the area are basalt and tuffaceous mudstone of the Late Jurassic or Cretaceous Nicoya ophiolite complex. The Nicoya Complex is overlain by weakly lithified Pleistocene Older Sediments, predominantly conglomeratic sandstone and derived from erosion of the Nicoya Complex. Erosion reduced the Complex to a surface of high relief, so that the detrital source was in the area originally; the source retreated with subsidence. Stratigraphically, the Older Sediments are followed by surficial deposits of intermediate age, consolidated Younger Sediments reworked from Older Sediments, and unconsolidated Holocene surficial deposits reworked from Younger Sediments. The most prominent structures are a northeast-trending anticline and northeast and northwest fault sets. Some deformation was Cretaceous, but folding and much faulting occurred after deposition of the Older Sediments. Remnants of plainlike features and destructional terraces on the Older Sediments attest to stepwise downcutting of the terrain during successive stages of uplift. Near the end of this process, the present valley floors and coastal headlands developed. During a probable epeirogenic rise in sea level, Younger Sediments filled the valley bottoms and an aggradational coastal plain developed. Sea level dropped by stages and with some reversals to its present position; this caused stepwise incision of the valley fill, stepwise beveling of the coastal plain, and development of the present wave-cut platform. Spilitization around the time of the Campanian orogeny caused some parts of the Nicoya complex to be calcitized and others to be silicified. Gold, pyrite, and probably additional silica were introduced during subsequent hydrothermal activity. Native gold was eroded from Nicoya Complex lodes and reconcentrated through three generations of placer gold deposits. First, the gold was deposited as a detrital.

Jan 1, 1977

By J. C. Gilbert

"IntroductionTHE PURPOSE of this paper is to discuss in a general way the heavy oil situation in Western Canada, and particularly to acquaint those in the oil industry who have not participated in the heavy oil end of the business with past and current developments. The author has covered •briefly the location of the heavy •and asphalt-base oil fields, their geology, current drilling and production practice, the location of the •refineries capable of handling heavy crude, their products and markets, and the problems and future prospects of the industry.Location and Description of FieldsThe term heavy oil is generally used to denote crude of 20.9° gravity and under. Since the products from heavy oil are also to a lesser extent obtained from asphalt-base crudes of higher gravity, some mention will be made here of the latter; but in general the emphasis of the paper is on heavy oil as such.In the order of their production to date, the heavy oil fields and those light oil fields which produce asphalt-base crudes are : Lloydminster, Taber, Vermilion, Conrad, Princess, and Wainwright.The Lloydminster oil field has not only produced most of the heavy oil, but also is currently the largest producer, supplying at the present time about 80 per cent of the heavy and asphalt-base crudes produced in Western Canada."

Jan 1, 1952

By Levi de Oliveira Bueno

Constant stress testing was used for characterization of creep behavior of a 1Cr0.5Mo steel plate in the ex-service condition. The tests were performed on creep machines equipped with Andrade-Chalmers type profiles, high sensitivity SLVC transducer extensometry, high stability temperature controllers, and facilities for monitoring the creep curves with an automatic data logging system. Ten creep machines of this type were used in this research, in an experimental work that lasted for one year. Three temperature levels were selected: 538, 565 and 593°C, with stress in the range from 52 to 224 MPa producing rupture times varying from 5 to about 3950h. The creep curves were all followed with great scrutiny using data logger scanning rates which enabled storing thousands of readings in each case. The experimental analysis involved measurements of minimum creep rate, rupture time and final elongation at rupture. The data were analyzed according to the classical phenomenological / physical relations (Norton, Arrhenius, Zenner-Hollomon, Monkman-Grant) and also considering five traditional parameterization methodologies (Larson-Miller, Orr-Sherby-Dorn, Goldhoff-Sherby, Manson- Haferd and Manson-Succop). Comparisons are presented among the possibilities of data extrapolation from five different methodologies. Comparison is also made with creep results obtained on a similar plate of the same material in the virgin condition.

Aug 16, 2017

By D Gerrard, J Begelhole, J Gerber

The Iron Magnet deposit has been mined since 2007 when Arrium (then OneSteel) commissioned the magnetite concentrator to supply feed to the pelletising plant in Whyalla. The concentrate quality requirement for the customer required consistent product with minimal variability. In the early stages of operation, it was identified that the feed variability introduced significant changes in the concentrate quality, which was outside the acceptable customer limits.In 2011, a geometallurgical regression model was developed that allowed for the estimation of concentrate quality produced from the feed material. This was based on a laboratory-scale Davis Tube Recovery (DTR) test performed on the feed material. The objective of the project was to characterise the raw ore in the pit to allow for blending prior to crushing. By blending the feed to the concentrator, minimal concentrate quality variation within the plant was achieved. The orebody was divided into geometallurgical classes, called ore types, based on the mineral texture and magnetic mass recovery. Each geometallurgical class consisted of material with similar metallurgical performances. For each individual blast pattern, the ore was grouped into the geometallurgical classes and a composite sample was created. The composite sample was put through the laboratory-scale DTR test and the results were used to estimate the metallurgical performance of the material.The characterisation process and feed pile build methodology was applied in early 2013 and went through an optimisation and streamlining phase. Since the implementation of the geometallurgical characterisation process, the plant has seen a significant reduction in concentrate variability and measurable throughput gains. The characterisation process has also increased the amount of material that is now classified as ore.CITATION:Gerber, J, Gerrard, D and Begelhole, J, 2015. Geometallurgy of the South Middleback Ranges magnetite deposit – predicting plant performance from the pit, in Proceedings Iron Ore 2015, pp 555–560 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By M. C. Esposito

Seven pyrite samples purified from coal sources and one ore source pyrite (for comparative purposes) have been characterized by chemical and mineralogical analyses, inherent floatability, apparent specific gravity, surface area, semiconductor type, optical anisotropy, dissolution and oxidation rate. The data clearly demonstrate that pyrites from various coal sources differ not only from ore pyrite but from each other as well.

Jan 1, 1987

By D. Kruse, M. Sanaei

"A three dimensional nonlinear finite element model was constructed to simulate and analyze the behavior of large diameter segmentally lined shafts when subjected to seismic waves. To reduce computation time, a less complex shell model was also constructed. Transient excitation was applied to the supported nodes of both models, at the base of the shaft, with a time-function representing the 1994 Northridge earthquake. The models are developed at the end of an original phased construction-stage analysis of the shaft. Displacements, forces and moments are monitored and compared during the analyses steps. During the initial 15 seconds of the earthquake, the top and bottom of the shaft show similar displacements. The maximum horizontal displacement within the shaft is approximately 3.5 inches in the solid model and the shell model results conform to this by a factor of 50%. Keywords: Segmentally Lined Shaft, Soil Structure Interaction, Seismic Analysis, Finite Element Modeling, Ground Modification INTRODUCTION TO SEGMENTALLY LINED SHAFTS Large diameter segmentally lined shafts (SLS) are underground systems, constructed sequentially using precast concrete segments to form a ring which provides both temporary earth support during excavation and permanent structural support. The segments are connected via alignment pins, bolts, packer material and other structural components that ensure the continuity of the SLS. In this analysis, the construction process uses a top-down sequence wherein each soil layer is excavated, damp-proofing is installed and concrete segments are assembled to form each ring. This process is repeated until design depths are achieved completing the shaft. It is known that cylindrical structures sustain lateral (earth) pressure mainly through the mechanism of hoop-stress. As Timoshenko’s ring theory goes, a cylinder shell structure is prone to buckling under external pressure [1]. In typical designs of small diameter shafts and tunnel linings with small diameter to wall thickness ratios, nonlinear buckling analysis (i.e., nonlinear geometric analysis) is not considered, since the buckling capacities for those structures are much higher than typical pressures encountered at their design depths. However, in shafts with large diameter to wall thickness ratios, buckling could become a critical issue. In any given mode, as buckling occurs in a ring, some sections of the structure move inward while alternating sections protrude. Although the presence of the surrounding soil could mitigate the buckling by resisting the movement (Soil structure interaction) seismic loads can cause ground movements and lateral pressures, exceeding the capacity of the structure. It is therefore essential to design the load bearing capacities of the shaft to minimize the possibility of any catastrophic failure due to earthquakes. This study explores the structural response of the SLS when subjected to seismic loads."

Jan 1, 2016

By Yongping Wu

The steeply dipping coal seams in this paper refer to those with the angle of inclination ranging from 35° to 55°. The reserves of the steep coal seams account for approximately 15%~20% of the total coal reserves in China. In the past 12 years, the top-coal caving mining method had been used to mine the steeply dipping thick (11.5-16.4 ft or 3.5-5.0m) coal seams. However, the mining process of top coal caving is complex with low recovery rate and nearly 30% of coal was wasted. Those problems can be solved by using the single pass large mining height (11.5-16.4 ft or 3.5-5.0m) method. But the movement of the overlying strata around the mining face area of large mining height is complex and it is hard to control the stability of ?rock-shield support? system. Therefore, field measurement, numerical simulation and physical (similarity material) simulation methods were used simultaneously to analyze the strata movement, roof structure and rock-shield support interaction characteristics. The results indicate that strata movement, which is the same as mining the steeply dipping seams with conventional mining heights, is asymmetrical about the dipping direction of the face; deformation, failures, and movement of the surrounding rocks are more intense; the roof weighting interval decreases; the weighting intensity increases significantly; and face sloughage occurs frequently. In the gob, the space for sliding and rolling of the roof increases; the broken main roof tends to form an anti-dip pile structure; the backfilling and compactness of broken roof increase at the lower portion of the face, thereby inducing significant unbalance in stress distribution between the upper and lower portions of the face. The overlying strata above the face form a multi-level step structure. The characteristics of contact and loading of roof-shield support system are more complex. The range of shield load variation is larger, and interaction between shield supports occurs frequently. Anti-toppling and anti-sliding devices at the face become more difficult to implement. The research results provide a theoretical basis for the mining practices in the steeply dipping thick seams with a large mining height. The practice in panel 25221 of 2130 coal mine indicates that the accident rates have been greatly reduced and good technical and economic benefits have bee realized.

Jan 1, 2014

By C. V. Deutsch, J. B. Boisvert, J. L. Deutsch

Data used to build geostatistical models come from a wide variety of sources with potentially differing sample errors and volume supports. Typically all available sample measurements are pooled together for statistical analysis irrespective of the quality of the data. The sample data is used to assess spatial continuity, make local estimates and assess uncertainty. A new methodology is proposed to simplify accounting for samples of differing quality. The result is improved estimates with higher weights assigned to high-quality samples, while low-quality samples receive less influence in resource estimation. A new dimension, d, is introduced and calibrated to account for sample error and/or volume during estimation. The addition of an extra dimension can be easily incorporated in existing kriging or inverse distance workflows. The only additional parameters required are the sample error and volume for each datum. The methodology is demonstrated and the improvement in local accuracy is documented. Extending the dimensionality of the domain to four (three spatial dimensions and the additional d dimension) requires a valid 4D variogram model; therefore, the spherical variogram model is generalized to arbitrary n-dimensions.

Jan 1, 2011

By M. J. Laurila

Elemental analysis of slurry streams using X-ray fluorescence (XRF) has long been employed. However, detector technology has limited the application of XRF devices. Using detector technology employed on NASA's Mars Pathfinder to analyze soil samples, Process Control, Inc. has developed an on-line analyzer to mount on a sampling system. The prototype XRF elemental analyzer was installed at Detroit Edison's Monroe Power Plant in January, 1998 and has been employed to monitor feedstock quality. A slurry system has been developed for flotation control. This paper describes the testing of the analyzer using the new, draft ISO standard for evaluating the performance of on-line analyzers (ISO/DIS 15239).

Jan 1, 1999

By C. M. Sellars, F. Maak

Electvomotie -force measurements hazle been made on ten Au-Ni alloys at temperatures 7754 825O, 900O, and 935°C using galvanic cells with solid electrolyte. Partial and ivtegral thermodynamic functions are derived from the determined activities. which show la9,ge positive deviations jvom Raoult's law. The enthalpies of mixing- are in close accord with calorinletric data and are of comparable accuracy. The results are used to determine the miscibility gap and the spinoidal curL1e, and are qlalitaticely interpreted in terms of the large size difference and electvonic interactions between gold and nickel. Tabulated nalues of the actielities and partial and inteqal free energies, entropies , and enthalpies of mixing are given in the appendix. The Au-Ni binary alloys are of particular interest thermodynamically as despite the large size difference between gold and nickel atoms they have a simple phase diagram.' This shows complete solid solubility above a miscibility gap with a maximum at about 71 at. pct Ni and 810°C. Activity measurements (over a range of temperature) have been made previously on this system using an electrolytic-cell method with a liquid chloride eletrolyte. The accuracy of this data has, however, been queried3'4 as it leads to values for the enthalpy of mixing which are too high when compared with calorimetric measurements.46 Also, the entropy of mixing is too high when compared with the values derived from specific-heat measrements. It was therefore considered worthwhile redetermining the activity data using a galvanic cell with a solid electrolyte (0.85 ZrO, 0.15 CaO). This method is based on a technique introduced by Kiukkola and aner'' and has been used to determine the thermodynamic data for Cu-Ni alloys.' THE ELECTROLYTIC CELL The cell used to determine the activity of nickel in Au-Ni alloys was: The cell reaction, which is discussed for a similar cell by Rapp and Maak, gives a direct measurement of the activity of nickel in the alloys as where aNi(alloy) is the activity of nickel in the alloy, 3 is Faraday's constant, E is the measured electromotive force, R is the gas constant, and T is absolute temperature. For the valid application of this type of cell the arrangement must be ther modynamic ally stable, which means that: 1) The free energies of formation of the oxides fulfill the relation 2) The vapor pressures or dissociation pressures of each component must be so small that during the time of the experiment the amount of any material transported by the gas is negligible. 3) Side reactions which change the alloy composition must be negligible. These reactions are possible both with the surrounding gas atmosphere and with neighboring solid material. The first two conditions are fulfilled by the above cell.' The third condition is approached by care in the experimental technique. The factors which control the attainment of equilibrium in this type of cell have been considered by Rapp and aak, who conclude that metallic diffusion in the alloy is the rate-control ling step. A lower temperature limit for the practical application of this cell is therefore set by the condition that equilibrium must be attained in reasonable times. EXPERIMENTAL MATERIALS AND TECHNIQUE The starting materials were mint gold (99.99 pct Au) and Mond nickel (99.9 pct Ni). Alloys, nominally 5 at. pct Ni and then each 10 at. pct across the system, were produced by vacuum-levitation melting compacts of mixed drillings of the pure metals. The nickel used for the reference tablets in the cells was melted in a similar manner. The alloy ingots, cast in boron nitride molds, were cold-forged and

Jan 1, 1967

By Ulick Evans

I SHOULD like to commence by saying how much I appreciate the honor which the American Institute of Mining and Metallurgical Engineers has done me in inviting me to visit your country, and to deliver this lecture before you. In choosing a subject, and in deciding what to include and what to omit, I have endeavored to discuss as far as possible work carried out recently in Europe with which you may not be unduly familiar. It would be poor return for your hospitality, and a mistaken sort of compliment indeed, if I were to load the lecture with accounts of researches carried out in your own country-researches with which you are probably better acquainted than I. Not that I have in any way excluded work done on this side of the Atlantic from my survey; one would indeed find it difficult to write on this, or on any other branch of science, without mentioning American work. But I have endeavored as far as possible to concentrate on aspects of the case which will, I hope, be comparatively fresh to you, and I feel fairly certain that this will be in accordance with your own wishes. If a strip of iron is heated strongly at one end, the other end remaining cold, there is produced over the heated portion a layer of oxide scale, the thickness of which diminishes steadily with the distance from the hot end. Somewhere in the middle of the strip, the thickness of the oxidized layer will become comparable to the wave length of light, and over this region the thin films give rise to a series of beautiful interference tints, commonly known as "temper colors." The colors are caused by the fact that two trains of light waves are reflected respectively from the outer and inner surfaces of the oxide film, and the possibility arises that the "crests" of one series of waves may coincide with the "troughs" of the other, thus diminishing the intensity of the light of some particular wave length. The state of affairs in this part of the strip is shown diagrammatically in Fig. 1, in which the film thickness is enormously exaggerated, of course, in comparison with the length of the strip; the

Jan 1, 1929

By D Frost, G Harbort, T Lipiec, N Deonarain

"The use of flotation columns has remained a contentious issue among mill operators. There are those who consider them an essential part of any mineral processing operation, while others consider them a necessary evil, which should only be installed if there is no alternative. Lastly, there are those who believe they should not be installed, no matter how great the perceived benefit.This paper provides an analysis of over 4000 installed flotation columns, contained in the Amec Foster Wheeler flotation database. Changing trends in column flotation use by type, commodity and geographical region are discussed. The effect of changing commodity prices and the China ‘phenomenon’ are reviewed. Special reference is made to the changing face of column flotation in Australia.Of note is the fact that after falling to a 20 year low in installed flotation column capacity in 2014, flotation columns during 2015 went through a resurgence in popularity. This resurgence was in direct contradiction to depressed metal prices and was driven by brownfield optimisations to reduce off-site costs, particularly in base metals. A case study is presented comparing the benefits of column flotation at high commodity prices with low commodity prices.Citation:Harbort, G, Deonarain, N, Frost, D, Lipiec, T and David, D, 2016. Changing Trends in Column Flotation Use - Their Impact for Australian Mill Operators, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 93–104 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By G Harbort, D Clarke, D Morgan, C Sola

Northparkes Mines commenced production in 1994 and the mine has significant reserves to allow operation into the future. There are a number of potential future concentrator feed sources with variable sulfide mineralogy and grades.In February 2012 a comprehensive flotation survey was conducted to allow mass balancing and evaluate the operation of the flotation circuit. A rudimentary, copper element only, unsized flotation simulator was developed to evaluate high level potential for optimisation and improvement. In 2013 this flotation model was expanded to produce a mineral based, floatability component model to estimate the effect of future concentrator feed source on metallurgical performance. This revised model allows various circuit configurations to be simulated to provide a high level blueprint for the long-term planning to maximise performance.This paper provides a review of the process followed to develop the model, including an analysis into the mineral floatability component model and its calibration against plant operations. The effect of varying feed mineralogy and feed quality on future performance has allowed an internal review of potential circuit changes needed to accommodate the changing future feed.CITATION:Clarke, D, Harbort, G, Morgan, D and Sola, C, 2014. Northparkes Mines – flotation and planning for the future, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 203–208 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By Eoffe SW

The wide application of computers in beneficiation plants has resulted in the creation of a number of complex automatic control systems at all stages of ore dressing processes. To create such systems it is necessary to solve complex problems of analysis and calculation. The application of computers to solve these problems demands development of simple and effective methods of investigation and simulation of ore dressing process dynamics because all the known methods are complicated in usage and cannot guarantee the desired accuracy and quality of process control. A new grapho-analytical method of investigation and calculation of ore dressing flow sheet dynamics, worked out by the authors of this paper, is based on proportion method development and is used to construct dynamic characteristics of the investigated processes. It is possible to use the given method for investigating benefication schemes with flotation machines having non-linear static characteristics and circulating loads. The suggested method of investigation of concentration flow sheet dynamics allows us to obtain dynamic characteristics of technological process parameters in both linear and non-linear systems. Moreover, the final result can be obtained without labour consuming analytical calculations by a simple graphical construction based on the static characteristics of the known equipment and processes.

Jan 1, 1993

By George A. Snyder

The presence of moderate to high concentrations of colloidal clays in coal preparation plant waters can cause serious operating and economic problems for a coal company. Among the host of possible problems are the following: 1) Poor separation of clays in the plant thickener, resulting in: a) Increased ash in the clean coal. b) Increased specific gravity of the wash water and decreased coal recoveries at the desired quality. c) Increased thickener operating costs in trying to overcome the problem. 2) Decreased solid concentrations in the thickener underflow and increased pumping requirements to meet solids withdrawal requirements.

Jan 1, 1979

By J. P. Schde

The authors deal with nickel production and usage patterns, nickel's first-use and end-use, examples of nickel applications in modern technology, e.g., energy generation and conservation, environmental protection, the oil and gas industry, construction and machinery, food production, conservation and distribution, consumer durables and the like. A special section of the paper is devoted to new applications of nickel in the electronic industry, modern corrosion control and the building and construction industries. The need to defend traditional markets for nickel while striving to find new applications, is also stressed.

Jan 1, 1988

By D. McElhinney, K. Mohamed, T. Batchler, T. Matthews

Steel props are a type of standing support utilized in coal mines to support mine roof. In addition to the vertical roof loading, sometimes the steel props are subjected to lateral loading of spalled ribs. To enhance the safety of mine workers, the performance characteristics of the steel prop was studied under different scenarios of vertical and lateral loadings. Quik Stik props were used for use in this study. A uniaxial compression loading test was conducted for the Quik Stik prop assembly (inner and outer tubes, ball bearings, collar) to investigate the loading mechanism of the prop. Rupture tests were conducted for the inner and outer steel tubes of the Quik Stik props to estimate the yielding strength of the steel tubes. Nine Quik Stik props of 8-ft high were tested using the Mine Roof Simulator (MRS) at the National Institute for Occupational Safety and Health (NIOSH) Pittsburgh research facility. Three props were tested under vertical loading to measure the vertical loading capacity of the props. Six props were tested under lateral loadings with low and high roof-to-floor convergences to measure the lateral loading capacity and the retained vertical loading capacity of the props during lateral loading. Vertical loading tests showed that the tested props could be classified as yieldable supports with a stable load capacity of about 110 kips to 140 kips. Lateral loading tests showed that the vertical load capacities of the tested props were diminished because of applying lateral loads, and the props behaved as nonyielding supports with a maximum lateral load capacity of about 8.5 kips to 9.5 kips at stable lateral displacement up to 3 inches.

Feb 1, 2023

By C Li

Removal of gangue minerals from ilmenite concentrates can be accomplished by relatively low temperature roasting in controlled gas atmospheres to selectively enhance the magnetic separation characteristics of the ilmenite. At roasting temperatures below 800¦C the magnetising reactions are often not consistent with phase equilibria considerations. Metastable phases can nucleate and control the roasting products. In weathered ilmenites the phase assemblages and microstructures in the altered ilmenite grains can influence the roasting reactions. In this paper we give an overview of the phase chemistry of chemically weathered ilmenites and of metastable phases formed by low temperature roasting. We also report the results of roast experiments conducted in a neutral gas atmosphere. Major increases in magnetic properties after short roasting times at low temperatures were obtained for a range of ilmenite concentrates. For example heating a secondary ilmenite concentrate from Western Australia for 15 minutes in nitrogen at 600¦C gave an increase in the three kilogauss magnetic fraction from three to 92 wt per cent. The solid state phase changes accompanying the inert atmosphere roasts were characterised by combining elemental analyses with quantitative phase analyses of the ilmenite concentrates and their roast products. It was found that the phase reaction that is principally responsible for the increase in the magnetic properties of weathered ilmenites involves a transformation of disordered ferrous-containing pseudorutile to an ordered ilmenite-hematite solid solution containing typically ten to 35 mole per cent of the hematite component. Examples are given of the application of the inert atmosphere roast to effect separations of ilmenite from gangue minerals.

Jan 1, 2001

By George S. Rice, J. W. Paul, E. H. Denny

Data assembled by the Bureau of Mines , coupled with requests from coal companies , have emphasized the desirability of establishing standardized specifications for brattice cloth with particular respect to durability and fireproofing . Brattice cloth is a canvas or other material , often covered with some fireproofing composition , which is used extensively in coal mining for temporarily deflecting air into pillar workings and maintaining ventilation at the working faces . These specifications will be established , it is planned , through a cooperative program in which the U. S. Bureau of Standards will make a series of tests of various brattice cloths treated with respect to fire- resisting qualities and the U. S. Bureau of Mines will continue to assemble field data on the use of brattice cloth . Plans now are being made for this cooperative work. Without attempting to make a complete survey , the Bureau of Mines has made preliminary studies and investigations , and verious representative coal - mining companies have furnished detailed information . The information thus gained will be used as the basis for the cooperative investigation , but the Bureau of Mines would welcome additional information from mine operators on the character and weight of brattice cloth , conditions of use , durability , quantity employed and price . Such information should be sent to the Director , Bureau of Mines , Washington , D. C. The mine operator is interested in procuring at reasonable cost a brattice cloth with lasting fireproofing quality and of as great durability and strength as possible . There has been a lack of assembled data and knowledge regarding the subject , but the Bureau of Mines feels that this lack of knowledge may be overcome if the coal -mining companies will lend their hearty support to the cooperative investigation and submit information relative to the use of brattice cloth in their own properties . Information contained in this report is based on data obtained from coal operators in bituminous districts of Pennsylvania , Alabama , Utah , Indiana , Illinois , Colorado and Nova Scotia .

Feb 1, 1923