Search Documents

By Isaac A. Zlochower

This paper presents data on the limiting (minimum) oxygen concentration (LOC), in the presence of added N2, of methane (CH4), propane (C3H8), ethylene (C2H4), carbon monoxide (CO), and hydrogen (H2), and some of their binary mixtures. It also addresses the issue of the flammable concentration (flammability) limits of these pure gases in air. The study is based on spark ignited explosions in large, spherical laboratory vessels (120-L and 20-L) using a 7% pressure-rise criterion for explosion propagation. The results of the study are compared with the older values which used long flammability tubes with a diameter >5 cm together with visual evidence of substantial upward propagation. They are also compared to results reported recently using a 12-L spherical flask with a visual flame propagation criterion. Finally, they are compared to results reported in Europe using more modest flammability criteria and smaller chambers. The findings reported here show excellent agreement between the 120-L and 12-L results, good agreement with the 20-L results, and reasonable agreement with the earlier flammability tube values for the lower flammability limits. They disagree, however, with the more conservative European values. These results and those from the 12-L experiments also feature lower LOCs than are given by traditional flammability tubes. A model for the LOCs of such fuel mixtures based on the Le Chatelier mixture rule for lower flammable limits is seen to reasonably fit the observed results on binary mixtures and can accommodate more complex mixtures as well. One such set of ternary mixtures containing CH4 and 1:1 CO:H2 is well fitted by the model.

Jan 1, 2009

By P McCarthy

"This paper is based on 30 years of involvement in feasibility studies as a participant, study manager and the leader of a firm that provides study components and overall study management. The following topics are discussed:the purpose of feasibility studiesaligning the goals of the study team with those of the ownerthe difference between optimisation and designhow the types and levels of studies affect the organisation of the studythe relative merits of various management structures and contractual arrangementssetting scopes of work and tendering the work outthe selection of a study manager and the study management teamcommunications within the study team and externallythe project management trianglemanaging scope changes and maintaining flexibility to respond to study findingsprogress paymentsmanaging a study crisisinnovation, risk aversion and bankabilityreporting the resultsthe dangers and benefits of value engineering.CITATION:McCarthy, P, 2016. Making studies work – organisation, communication and management, in Proceedings Project Evaluation 2016, pp 20–30 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By Knud Sinding

Many industries have established their own systems for self-regulation. They often do so when companies operate in countries where financial, technical, environmental and social regulation is weak and when the industry is challenged by legitimacy issues related to behaviour in one of these areas. Mining is one industry that has progressed unevenly down the road of self-regulation in these areas. This paper examines how the development of self-regulation for mines and mining companies involves difficult questions of scope, rules, membership, assessment criteria and performance evaluation. Using a range of theoretical and empirical results from research on self-regulation, performance rating and corporate strategy, this paper analyses the strategic and operational issues related to the idea of self-regulation in the mining industry. The analysis indicates that while self-regulation may bring benefits to members, they are likely to take a long time coming; but when they do arrive they may be substantial. Using the fact that in relation to technical and financial issues the industry is quite experienced in self-regulation ? not least as it is more reluctant in areas such as environmental and social performance ? the case is made for a comprehensive and innovative approach, that draws on the areas where the industry is experienced and develops new institutional solutions in the areas where the industry is more reluctant.

Aug 1, 2013

By P B. Hills, R J. Walton

Geotechnical instrumentation has been implemented as a key step for monitoring and optimising an engineered mine design for managing seismicity at the Beaconsfield Gold Mine. Measurements of displacement, stress change, ground control element load and seismic response of the rock mass allow for back analysis and calibration of critical parameters for feedback into the engineering design loop. Instrument clusters are installed in strategic locations prior to the commencement of stoping in order to determine the nature of the response of the rock mass to stoping. A selection of instruments including instrumented cable bolts and rod extensometers, resistance wire extensometers, hollow inclusion stress cells, vibrating wire stress meters and resistance wire extensometers are used to gather data through a data logging system. The rate at which data is recorded is adjusted to provide more information during periods of anticipated rapid change such as around stope firings or during periods of high seismic activity, and less information during periods of anticipated quiescence. The twofold purpose of the instrumentation is to calibrate the numerical modelling output which forms the basis of the engineered mine design, and to provide an alert mechanism where the behaviour of the rock mass is not what was anticipated, or where the impact of that behaviour may compromise the integrity of the engineered ground control system. The paper describes the location of instrument clusters with respect to stoping, the type of instruments employed and the method of data acquisition. It provides examples of results obtained and illustrates the way in which that information is used to optimise the mine design and manage seismicity.

Jan 1, 2008

By R. E. MacAfee

THERE have been great changes in the design, capacity, and pressure of steam generating units over the past fifty years. If we go back as far as 1890, the plants then existing were largely horizontal return tubular boilers, hand-fired, with the boilers supported on the brick sitting which was com-posed of red brick with, probably, a refractory lining one brick thick in the combustion chamber. About this time, the water tube boiler began to supplant the H.R.T. boiler and, where new plants were being constructed of any size, water tube boilers were largely installed. In those days, say from 1890 to 1905, a 250 h. p. water tube boiler was considered a large unit. These boilers were largely the straight tube type and were set with the first row of boiler tubes three to six feet above the grates. The brick setting was a combination of red brick and fire-brick. The fire-brick lining in the furnace proper was usually 9 in. thick and in the first pass 4 1/2 in., while the rest of the setting was entirely red brick. These units were largely hand-fired and were expected to produce about 100 per cent rating as a maximum. It may be well at this point to define rating, which is the evaporation of one boiler horse power per hour by each ten square feet of heating surface in the boiler. A boiler horse power is the evaporation of 34.5 pounds of steam from and at 212°F. Consequently, a boiler containing 2,000 square feet of heating surface is rated at 200 h. p. and the evaporation at 100 per cent rating is 200 X 34.5, which equals 6,900 pounds of steam per hour from and at 212°F.

Jan 1, 1939

"In an environment of rising energy prices and mining at greater depths, cost-efficient loading and hauling equipment is essential. Conducted at an underground mining operation, this study analyzes the energy consumption and gas emissions of diesel and electric load-haul-dump machines (LHDs) with similar bucket capacities. Based on energy prices from the first quarter of 2014, results of discrete event simulation show that energy costs for diesel and electric LHDs are US$0.24/t and US$0.07/t, respectively. Also, diesel LHDs emit 2.68 kg CO2 per litre of diesel fuel, whereas using electric machines reduces the need for ventilation to mitigate engine heat and emissions and reduces energy costs.RÉSUMÉ Dans un contexte de croissance des prix de l’énergie et d’exploitation minière à des profondeurs de plus en plus grandes, il est essentiel d’avoir des équipements de chargement et de transport les plus rentables possible. La présente étude, effectuée dans une mine souterraine, analyse la consommation énergétique et les émissions de gaz de chargeuses-navettes (LHD) au diésel et à l’électricité ayant des capacités de godet similaires. En se basant sur les prix courants de l’énergie, les résultats d’une simulation d’événements discrets montrent que les coûts énergétiques pour les LHD au diésel et à l’électricité sont respectivement de 0,24 $US/t et de 0,07 $US/t. De plus, les LHD au diésel émettent 2,68 kg CO2 par litre de combustible diésel alors que les machines utilisant l’électricité réduisent le besoin de ventilation pour atténuer la chaleur des moteurs et les émissions en plus de réduire les coûts énergétiques."

Jan 1, 2015

By M. Timmins

Campbell Mine operates a 100 tpd gold autoclave that treats sulphide concentrates at 305 psi and 200 °C. Autoclave feed consists of fresh pretreated concentrate, an acidic oxide slurry recycle as well as other high arsenic sources. The brickwork that is used to construct the five compartments of the vessel must be inspected and repaired periodically. Shutdowns are scheduled to inspect this brickwork and at times replace entire sections of the brick walls or lining. It also provides an opportunity to repair or replace other internal features such as agitator blades or oxygen spargers. Mechanics and contractors are scheduled around the clock to perform the maintenance requirements. There are many safety considerations and precautions that must be taken in order to protect the well-being of the workers and minimize damage to sensitive pieces of equipment. Heat, arsenic and lead contamination and confined space issues are just a few of the hazards involved. The following paper will describe how these safety concerns are addressed and will serve as a guide for future autoclave shutdowns.

Jan 1, 2004

By C Carbonneau

In order to successfully produce columbium pyrochlore concentrates, St. Lawrence Columbium and Metals Corporation had to face two principal problems met in several new operations but possibly made more acute than usual owing to the newness of the project. 1.-The ore is particularly complex, as it is made up of an elaborate intermingling of carbonates and discontinuous ultra-alkaline rock bodies of various ages and types in which no less than seventy mineral have been re-ported. Obvious petrographic or structural controls are lacking. Ore boundaries have to be defined on the basis of assay results and the determination of several minerals which occur in trace amounts. 2.-The pyrochlore concentrates produced had to com-ply with a set of stringent specifications. This fact, combined with the low Cb205 content of the ore, necessitated the use of a beneficiation process that would have to operate at a concentration ratio greater than 100:1. A brief description of the mill circuit is given. Mill stability was obtained through extensive mineralogical study of the mill feed coupled with close geological and engineering control of the mining operations.

Jan 1, 1965

By Webster, Wm. Reuben

THE greatly enlarged demand for small sizes of seamless copper tube which has recently occurred, due particularly to the rapid growth of the electric household-refrigerator industry, has emphasized the superiority of phosphorized to tough pitch copper for the purpose of producing this commodity. In the manufacture of this material exceedingly heavy reductions by cold drawing are employed, customary practice involving as much as 90 per cent. reduction of cross-sectional area in four runs without intermediate annealing. Although this superiority has long been recognized by tube makers, no quantitative expression of it has heretofore been published. It is believed that the data herewith presented mill serve this purpose. Recent investigators are not in agreement as to the relative mechanical properties of copper containing small amounts of oxygen as compared with copper containing sufficient oxygen to produce that condition known as tough pitch. Hanson, Marryat and Ford1 found that "oxygen has a relatively small effect on the properties of copper." Johnson, on the contrary, states "it cannot be denied that it (tough pitch copper) is inferior to deoxidized copper . . . where severe mechanical manipulation is concerned." These authorities in the reports of their investigations, as might be expected from their conclusions, do not present data of a character requisite to a conclusive determination of the question.

Jan 1, 1927

By V. Ross

"Bench-scale flotation tests play a major role in the geometallurgical process value chain. Despite their apparent simplicity, these tests pose pitfalls in terms of operation, as well as the interpretation and modelling of results. In this paper we highlight key aspects to consider in generating accurate and reproducible experimental results, and critically review some assumptions relating to the estimation of entrainment and froth recovery. We subsequently focus on first-order equations to model kinetics and propose a method that accounts more realistically for the decay in kinetics over the duration of a float, and the contributions of froth stability and hence mass pull. The method was applied to three case studies on platinum group metal (PGM) ores and matched or outperformed first-order, two-component models. Also, it allows for a deeper analysis of the integrity of the bench-scale flotation results. IntroductionGeometallurgy is a structured, multidisciplinary approach that integrates key data from the geological, mining, mineralogical, and metallurgical aspects of the value chain to construct spatial models of an ore deposit such that the overall economic benefit and sustainability of an operation can be optimized. Process geometallurgy is aimed primarily at enhancing metallurgical efficiency and plant throughput by the application of appropriate mining and processing strategies, as well as supporting production planning and operational strategies to reduce the impact of highly variable ores. With flotation being the dominant concentrating process in the mineral value chain, the bench-scale flotation test is an important characterization tool – a relatively cheap, simple, and rapid way to obtain key information about the ore and its amenability to economic extraction of valuable minerals. This includes the evaluation of different ore types and the implications of mineralogical composition and texture for comminution and floatability, the effect of the grinding environment on the liberation of minerals, the electrochemical environment in the pulp (Bradshaw et al., 2006), the screening of reagents to improve floatability (Ekmekci et al., 2003), and the role of hydrodynamics in the recovery of valuables and the entrainment of gangue (Amini et al., 2016; Wang et al., 2016). It is also a critical tool in auditing the performance of a flotation plant by hot floats, paving the way for concept and feasibility studies and providing essential data on kinetics for the purposes of scale-up, optimization, and simulation of flotation circuits."

Mar 1, 2019

By Miguel E. Ruiz, America L. Fernandez, Miguel A. Pandon

"Post-grouted drilled shafts (PGS) are a deep foundation system in which grout is injected at high pressure throughout the tip after the drilled shaft has been installed. Pressure grouting of drilled shaft tips can significantly increase the ultimate capacity and stiffness of drilled shafts. Conventionally constructed drilled shafts usually require higher axial deformation to develop the available side friction and the tip resistance simultaneously. They also tend to have higher tip compressibility and reduced end bearing capacity due to disturbance at the bottom of excavation during drilled shaft construction. PGS foundations have been found to be a cost-effective solution to compensate for this capacity reduction and/or compressibility increase. PGS construction procedure counterbalances tip compressibility and end-bearing capacity reduction. The tip grouting also has a pre-stressing effect over the shaft side friction since the drilled shaft tends to move upwards during the pressure grouting of the tip. After grouting, a bulb tends to form at the pile tip pre-compressing any disturbed material and, in certain cases, increasing the tip area, thus increasing shaft tip capacity.PGS load-settlement predictions using a load transfer approach are presented in this paper and compared with corresponding load test data. The paper also presents the main findings of load transfer analyses that were carried out to investigate the potential different factors that may be contributing to the observed improved performance of PGS over conventional drilled shafts. Results show that the two main factors, that may have a significant contribution on the overall performance of the foundation by increasing its ultimate capacity at any given level of settlement, are the stress-reversal of the skin friction and the formation of a grout bulb at the tip. The grout bulb tip contributes primarily through the increased tip area and to a lesser extent through increased stiffness and strength of the soil in the vicinity of the pile tip."

Jan 1, 2005

When selecting a method for monitoring crack growth in pipeline steel, the sensitivity or crack-size resolution plays a dominant role. Even though there are several visual and non-visual methods, the direct current potential drop (DCPD) method is very effective for monitoring crack growth because of its resolution. This method has been used for the past few decades and has gained increasingly wide acceptance in fracture research as one of the most accurate and efficient methods for monitoring the propagation of cracks. Furthermore, most R&D experience has proven that the electrical potential method can be used in most "aggressive" environments. For these reasons, the DCPD method was selected to design a testing machine to monitor corrosion fatigue crack growth. The use of finite-element modelling is shown to facilitate the application of the DCPD method for monitoring crack growth in steels. The 2D model calibration provided a good description of the test data and proved more accurate than the analytic Johnson's formula.

Jan 1, 2005

By Mehmet Guney

Acceptable working environments in production areas and service openings of Mindola Mine on the Zambian Copperbelt are currently maintained with an air volume of 1000 cu m/s and 5500 kW of installed refrigeration plant. It is planned to open up additional deeper areas of the mine for future production. Temperature problems, due to the increased heat generation from various underground sources are recognized as potential hinderances to efficient production. Findings of research work indicate that the present total heat output of 58,000 kW will inevitably increase by the second five-year period of the deepening program to 52,900 kW and by the fifth five-year period to 63,200 k\V. Estimated WB and DB temperatures, representing the total heat generation in stope faces and development headings during these same periods are predicted to increase to 53.8/40.2 °C and 35.5/42.1 °C respectively. It is assessed that the nominal refrigeration capacity needs to be progressively increased to 9,000 k\V This paper deals with the thermal problems in Mindola Mine, current heat output calculations, future prediction of temperature and heat load in various working areas of the mine with the application of computer programs and interpretation of data in order to find the effective solution for long-term planning of ventilation and air-conditioning.

Jan 1, 1982

By Ott F. Heizer

This paper describing the practice at the tungsten concentrator of the Nevada-Massachusetts Co., Inc., at Mill City, Nev., is one of a series being prepared by the Bureau of Mines on milling practices, methods, and costs in the United States. The ore, which contains about 1.10 per cent of scheelite (CaW04), is concentrated on tables and by means of a magnetic separator and roasters. A product containing 70.43 tungsten trioxide is shipped. The plant was designed for a capacity of 100 tons per 24 hours, but at present 142 tons of ore are milled per day. The author acknowledges the assistance of William O. Vanderburg, associate mining engineer, U. S. Bureau of Mines, in preparing this paper.

Jan 1, 1930

By R Schiller, E Chait

"Quebrada Blanca is a porphyry copper deposit located in the Eocene-Oligocene belt of Chilean Andes. Operation started in 1994 and original reserves for supergene mineralisation gave a life-of-mine (LOM) of 20 years; however, further exploration extended the LOM until 2020.In order to optimise the remaining five years of supergene resource, geometallurgical variables were added to the geological model including copper recovery and acid consumption. LOM plan encompasses finishing the phase number eight and the future development of phases 11 and 13.LOM lithologies include diorites, quartz monzonites, porphyries, igneous and tourmaline breccias. Main alterations are: potassic, phyllic and argillic. Litho-alterations or geometallurgical units were formed by combining five types of rocks with three types of alteration. According to statistical information, the deposit can be represented with 12 litho-alteration units, which cover 98 per cent of the LOM volume.For copper recovery information, there were 40 mini-columns tests made in order to obtain kinetics curves and copper recovery values after comparing the difference between head and tails grades. Acid consumption was obtained using an automatic neutraliser device-based test.Historical data said that copper recovery in pads after 450 days of irrigation is around 75 per cent of recoverable copper while acid consumption is around 5.5 kg/t.According to this study, lower recoveries are related with potassic-altered diorites and argillic-altered quartz monzonites with values around 60 per cent. On the other hand, best recoveries could be found in potassic-altered quartz monzonites and argillic-altered diorites with values closer to 80 per cent.It was also revealed that the most reactive rock is the potassic-altered diorite with 12 kg/t of acid consumption. This rock covers approximately 40 per cent from phases 11 and 13.The final geomet model was calculated using a program that relates each geometallurgical unit with a specific copper recovery and acid consumption value. Results found after comparing model-obtained information with historical leached pads data were used to validate the model.CITATION:Chait, E and Schiller, R, 2016. Adding Copper Recovery and Acid Consumption Variables to the Geological Model of Quebrada Blanca, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 257–266 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By Steven J. Page

Accurate measurement of workplace respirable dust concentration is an essential step in eliminating lung disease in any occupational setting. In the United States (U.S.) coal mining industry, this measurement process has relied upon a personal sampler that includes a 10 mm Dorr-Oliver (DO) nylon cyclone operated at a flow rate of 2.0 L min-1 to collect a respirable dust sample. Dust concentrations measured with this sampler are multiplied by 1.38, which was empirically derived, to convert them to measurements approximating the United Kingdom British Medical Research Council (BMRC) definition of respirable dust upon which the health effects of coal mine dust are based. The International Organization for Standardization (ISO) subsequently refined the respirable dust definition and the U.S. National Institute for Occupational Safety and Health (NIOSH) 1995 Criteria for a Recommended Standard presented a conversion multiplier of 0.857 to apply to the 2.0 L min-' DO (in addition to thel.38 multiplier) to obtain equivalent ISO concentrations, as approximated by the 1.7 L min-1 DO. However, the conversion multiplier 0.857 was derived indirectly from a limited size distribution data set rather than a direct comparison of the DO samplers. The present analysis focuses on providing a more accurate conversion multiplier derived from direct comparisons of the 2.0 L min-1 (with 1.38 BMRC equivalency multiplier) and 1.7 L min-1 DO cyclones. A weighted linear regression analysis of this database suggests that a more accurate estimate of the conversion multiplier is 0.815.

Jan 1, 2009

By Klaus Bauckhage

Phase-Doppler-anemometry (PDA)-measurements have to be taken from representative measuring positions from inside the spray cone, helping - with the support of simulated data of improved process models - to describe the multiphase flow situations within the spray cone - and accordingly to that - the heat transfer conditions for the rapid cooling and (partly) solidifying melt droplets before their impact onto the substratddeposit. Simulations and PDA-measurements thus give the base to confirm the hypothesis of the existence of a semisolid mixed-layer and it's influence on the resulting material structure during compaction. The dispersed particles in the spray cone exhibit a cooling and solidification process within a split of a second, which leads - as far as the particles solidify - to a dendritic structure with very short dendritic arm spacings. This causes within the particles extremely short distances for the following equalizing diffision processes taking place on a high temperature level (between liquidus and solidus) in the semisolid mixed-layer of the deposit and explaining the short residence times within this zone of only seconds up to a few minutes. This and the fact that the globular structure of the mushy zone (in the semisolid mixed-layer) leads to an unidirectional crystallization process over very short distances also explains the chemical and morphological ,homogeneity of the sprayed material. The dynamics of these process steps, the very special buffer function of the mixing layer during parameter variations as well as the controlled cooling process of the preform in order to avoid hot cracks influence the quality of the material. Due to the necessity of measuring and controlling the particle bound mass-, momentum- and enthalpy- fluxes to the deposit the PDA-technique has been adapted and modified in order to receive in-line and (in the future) also on-line data from the dynamics of the multiphase flow conditions within the spray chamber.

Jan 1, 1999

By D. R. Willmer, E. J. Haas

"DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health. Reference to specific brand names does not imply endorsement by the National Institute for Occupational Safety and Health. ABSTRACT This study analyzed the publicly available health and safety policies of 26 mining companies to determine the quantity of health and safety (H&S) practices that mining companies encourage in relation to the Plan-Do-Check-Act cycle. A thematic content analysis of the policies identified elements and practices within the text. On average, companies communicated information on about 7 elements (range 1–14, standard deviation = 3.49) and discussed 15 practices (range 2–34, standard deviation = 9.13). The elements in which companies highlighted the most practices were risk management, emergency management, leadership development, and occupational health. A discussion of the policy trends shows areas that mine sites can improve upon within their Plan-Do-Check-Act cycle, in addition to encouraging the use of both leading and lagging indicators to manage health and safety performance. INTRODUCTION Mining companies and their employees are expected to identify and manage risks at their worksites to ensure the health and safety (H&S) of everyone at the site. The primary mechanism in place to control these risks is a company’s health and safety management system (HSMS) (Boyle, 2012). Broadly, an HSMS is a set of standard, interrelated, and interacting elements used to promote and achieve occupational H&S goals (ANSI/AIHA Z-10, 2012; BS OHSAS 18001, 2007). The practices conveyed within an HSMS are expected to minimize incidents, injuries, illnesses, and even save worker lives (Alsop and LeCouteur, 1999; Arocena and Núñez, 2010). In the United States, both the Occupational Safety and Health Administration (OSHA) and Mine Safety and Health Administration (MSHA) regulate and encourage aspects of an HSMS (US Federal Register, 2011, 2010). Many HSMS documents (i.e., Chemical Industries Association, 1995; Health and Safety Executive [HSE], 1995; International Labour Office [ILO], 2001) attribute the source of their basic management system to Deming’s Plan-Do-Check-Act (PDCA) model of continuous quality improvement and organize their practices within this cycle (Johnson, 2002). The PDCA cycle is a well-adopted approach in health and safety management and promotes continuous learning and adaptability (Robson et al., 2007)."

Jan 1, 2018

By J. A. Herbst

Ball mill grinding circuits can be subject to upsets that arise from variable characteristics of the feed ore. These upsets are transients in critical circuit variables such as ball mill mass holdup, circulating load, sump level, cyclone efficiency and product particle size. They may occur frequently so that the operation is continuously fluctuating or they may be of such magnitude that some of the equipment is overloaded, resulting in shutdown, or an undesirable product particle size. The feed ore characteristics that influence ball mill circuit behavior in this manner include the grindability of the ore, the eventual transport characteristics of the ore in the mills and the feed ore size distribution. Control strategies for grinding circuits using conventional proportional-integral (PI) control have limitations to their effectiveness in controlling against feed ore disturbances. The first of these are the interactive nature of two or more control loops on a single circuit. Under some circumstances they begin to fight each other, increasing control error and settling time. PI control loop gain constants can be tuned to give best response for some set of conditions but once these change, as they would with a change in the feed ore, they are no longer the "best" ones (Shinsky, 1967). Due to these limitations, alternatives to conventional PI control strategies have been investigated for grinding as well as other mineral processing operations. These alternatives, all computer-based, include self tuning regulators, decoupling control and optimal control (Herbst and Bascur, 1983).

Jan 1, 1984

By P. O. Lindahl

The U.S. Bureau of Mines initiated research to improve the safety and efficiency of transporting coal from deep underground mines using a balanced air-lift hydrohoist. A 50-m-high pilot-scale model was constructed and tested to evaluate the feasibility of hydraulically hoisting a coal-water slurry in a U-tube pipeline from the mine level to the surface with the assistance of compressed air. A prototype screw feeder is used to continuously compact and inject 5-cm or less run-of-mine coal into a pressurized 20-cm-diam pipeline. Production rates up to 40 metric tph at an airflow of 1.5 m3/min were achieved with the model, and coal size degradation was relatively minor. Modifications are in progress to achieve 100 tph at an airflow of 2.8 standard m3/min injected into the riser pipe. Pilot-scale results indicate that an air-lift hydrohoist system is a feasible, cost-effective alternative to conventional skip hoisting that can be installed in existing shafts or surface-drilled holes closer to the face area. Air-lift hydrohoisting offers advantages of infinitely adjustable slurry flow rates, reduced pressure at the point of coal injection, and flexible design that can be combined with hydraulic pumping. Proposed design changes are discussed for coal transport, mine layouts, ventilation, fire control, and escapeways using this system.

Jan 1, 1995