Search Documents

By R. W. Titshall

WHAT IS SAMPLING? We are all involved in sampling almost every day of our lives, by tasting, feeling, or smelling. Most raw materials, food products or manufactured items are sampled several times at various stages of the production process before a commodity of suitable quality can be produced. Data obtained from sampling is used in establishing price, quality control, allocating production costs, or overall process efficiency. The area of sampling outlined in this article is the collection of a small quantity of material from large continuous bulk flows of solids and slurries. The concern in obtaining the sample is that the material obtained is truly representative of the main flow in every respect. The methods and equipment outlined are for the collection of a manageable sample. The sample has to be analyzed in a laboratory to determine its characteristics and compliance to set standards. SELECTING A SAMPLING SYSTEM When selecting a sampling system, it is essential to define the requirements, as to what the actual sample obtained will be used for and what degree of precision is required. Determine whether or not the system has to comply with any set standards such as A.S.T.M. (American Society for Testing and Materials) which have established methods for collection of a gross sample of coal. Sampling which is done for in-plant or process control is not generally governed by set procedures, but similar care should be taken during the selection process so that when the equipment is put into service it will operate reliably and produce a sample which is truly representative of the total material lot or consignment.

Jan 1, 1982

By Miguel A. Cuba

Trends in the mean and/or variance are a longstanding challenge in mineral resource modeling. Geologic modeling and/or grade domaining are often employed to account for heterogeneities in mineral grades; however, this is only practical up to a certain point since the number of data available for reliable model construction can be severely reduced. In such cases, trends remain present in certain geologic/grade domains and directly impact the modeling methodology; the trend must either be handled explicitly or a suitable approach is adopted to implicitly account for it. This is highly dependent on understanding the source of the trend. We propose an approach that detects the source of non-stationarity, which is based on quantifying the impact of non-stationarity in the mean and the variance via the semivariogram. By expanding the methodof- moments approximation of the semivariogram, we decompose the experimental semivariogram is into three terms: 1) trend in mean component, 2) trend in variance component and 3) stationary component. We can then assess the source of trend by calculating the contribution of each component at every lag. Two cases are presented to illustrate this tool. Firstly, a synthetic reference model is simulated and different trend patterns are added; the influence of these patterns in the experimental semivariogram calculation are analyzed and discussed. Secondly, a real dataset is considered where the impact due to the presence of trends in the mean and variance are assessed. The results of this paper reveal the semivariogram to be a tremendously powerful tool in determining the source of the trend. This insight may be useful in the selection of a suitable modeling approach for resource estimation.

Oct 1, 2009

By Andrew Mackenzie, Paul Rantala

Data is now appearing in literature that indicates many current paste fill systems in Canada suffer from plugged lines and severe wear rates. Both of these conditions suggest: design problems with the pipe distribution system, backfill composed of poorly graded material and/or possibly poor operator practices. Problems that can be prevented in the design stage, but still may be readily solvable with current technology. However, if left untreated will lead to an increasing frequency of down time. The compatibility of the distribution system with the paste fill rheology is fundamental and essential for the reliable delivery of fill. Either many mine operators are not familiar enough with the technology to provide a critical review that could foresee problems down the road, prior to construction and or North American designers are not clarifying their designs to their customers. The objective of this paper is to highlight key concepts to mine operators with the purpose of better enabling a critical review of contractor's/consultant's designs. There is a great deal of understanding about the rheology of backfill over a range of pulp densities from hydraulic slurry to dense to paste. However, outside of deep mines (especially in South Africa) neither hydraulic or dense fill distribution systems have suffered the problems of paste fill. Paste fill is fundamentally different from hydraulic fill principally in its transportation characteristics. These differences have a direct impact on the design of the distribution system. By understanding the practical implications of these differences the operator can play a more active role in their design while better appreciating how to best operate their own system.

Jan 1, 2001

By Henri S. Swolfs

INTRODUCTION In this paper we present preliminary results of a research program in site characterization methodology. We are interested in under- standing the response of discontinuous rock to mechanical, hydrologic, and thermal loadings. To carry out such a study we selected a field site with simple geology, uniform distribution of lithologies, and easily verifiable boundary conditions on temperature, fluid flow and stresses. The spatial distribution of fractures at the site was established and tests were conducted to determine the temperature field, hydrology, rock-mass properties, and in situ stresses. As part of the study selected borehole instruments were compared to assess their performance and reliability. SITE GEOLOGY The study area is in the eastern part of South Table Mountain, a mesa near Golden, Colo. The exposed cap rock is a single lava flow of uniform thickness (6-7 m) that rests on the clastic sediments of the Denver Formation (Van Horn, 1976). The surface of the cap rock (N. 75º E., 3º S.) is topographically featureless and slopes south- southeast; drainage is predominantly downdip and punctuated by occasional contact springs. The age of the lava flow is 64-65 m.y., or early Paleocene. Paleo- botanic evidence confirms the upper part of the Denver Formation as Paleocene (Van Horn, 1976). "Rapid-rock" analyses of core samples from the lava flow at three depths (0.2, 3.3, and 5.8 m) suggest a uniform chemical composition throughout with an increase in the Fe2O3/ FeO ratio (1.05 to 1.60) with increasing depth, reflecting the existence of a perched water table in the lava flow, To identify the rock

Jan 1, 1984

THE book covers principally the assaying of silver and gold and the determination of these values in ores, sweepings, and base metal. It seems to have been written more for the goldsmith and jeweler than for the primary producer of metals. There were approximately sixty different substances needed in the operations described and not over a dozen different types of raw material (ore, matte, crude or alloyed metal) are mentioned. The methods of separation used were essentially simple and reasonably reliable, though the processes were not sufficiently understood to permit the selection of the simplest effective ingredients, and there was a great tendency to employ complicated fluxes, with unnecessary repetition of long-continued heatings indicative of a leisurely pace of life. Practically all the processes described are based on a few chemical facts: the inability of gold to combine with sulphur, while silver and the base metals form easily fusible sulphides; the ready oxidation of base metals; and the ii- solubility of gold in nitric acid. Fluxes serve to make earthy impurities fusible, and to carry oxidizing or sulphurizing ingredients. Many of the processes of assaying had changed little up to the beginning of the present century. Even as late as 1924, when the writer took a University course in fire assaying, the crucibles, cupels, scorifiers, molds, and tongs were identical with those of the sixteenth century, though the wind furnace had a stack on it and the muffle for cupelling was gas-fired.* The fluxes were purer, but of the same essential composition. That this branch- or twig-of metallurgy had not advanced in any funda-

Jan 1, 1949

By R. Pérez, James A. Finch, F. Tavera, Cesar O. Gomez

"Gas holdup is a variable which affects the operation of flotation columns. On one hand, gas holdup is a function of bubble size (a function of sparger type, frother characteristics and concentration, and air flowrate), tailings flowrate, solids content, and mixing patterns in the collection zone. On the other, gas holdup defines flotation kinetics and carrying capacity. Therefore, gas holdup is a useful variable to control and diagnose the operation of a flotation column, but the lack of a reliable sensor for on-line gas holdup monitoring has prevented its use in industry.This work describes the principle and the practical difficulties associated with the development of a gas holdup sensor based on the measurement of the electrical conductivity of dispersions. Two different approaches have been devised. These approaches will be described and test results presented of prototypes in laboratory and industrial columns.Background.Several years ago, a research program was initiated at McGill to use electrical conductivity as the basis for developing sensors for process measurements in mineral processing. Electrical conductivity is an intensive property which is a function of the concentration of the different phases present in a dispersion. The initial focus was on the detection of the interface between two dispersions with different characteristics (i.e., that between the collection and froth zones in flotation columns or that between clear water and sedimented solids in thickeners). The technique works in this case by searching for the location at which a sudden change in specific conductivity occurs, as a consequence of different gas holdup or solids content, and absolute values of the specific conductivity of the dispersions involved are not necessary1,2."

Jan 1, 1995

By H. A. Davies

DURING a current program of research on the structure and properties of liquid sodium alloys, the need arose for information on the solubilities as a function of temperature of several B subgroup metals in liquid sodium. In the absence of reliable information in the literature for several of these systems, par- ticularly at temperatures in the range 100° to 300°C, an apparatus was constructed to determine solubilities by a direct melt-sampling technique, followed by wet-chemical analysis for both sodium and the solute metal. The details of the technique have been described previously.' The solubility of indium in liquid sodium was determined at eight temperatures in the range 100° to 270°C. The solubility as a function of temperature is shown on Fig. 1; this represents the liquidus line over this composition range. A cooling curve was plotted after the completion of the sampling and an arrest was observed at 94.9°C which must be interpreted as being the result of a eutectic reaction. By extrapolation of the liquidus to this temperature, the eutectic composition was estimated to be about 0.25 at. pct In. The present estimate of the eutectic temperature and composition are in good agreement with the values of 96.0° to 96.2°C and between 0.28 and 0.45 at. pct In, respectively, which were reported by Heycock and Neville.2 However, no further information on the liquidus of this system at the sodium-rich end could be found in the literature for comparison. One compound: NaIn, has been reported in this sys-

Jan 1, 1968

Improve the reliability and accuracy of subsurface images using constrained tomography with enhanced ray-tracing capabilities. Background Geophysical tomography is a technique for imaging the structure of a rock mass using seismic or radio waves, in the same way that medical CAT scans image human tissue using X-rays. Tomography has found numerous practical applications related to mining, including lithologic and structural characterization, fracture detection and fluid monitoring, void detection, and evaluation of stress state and integrity of mine structures. Problems Two fundamental problems have largely prevented geophysical tomography from enjoying the tremendous success achieved by medical tomography. The first is a consequence of practical limitations on the placement of sources and receivers of wave energy: ideal resolution can be attained only when the region being imaged is entirely surrounded by sources and receivers, so that it is crossed by rays traveling in all possible directions. When such coverage is impossible or impractical, the inversion becomes underdetermined: there id not enough information in the measured data to provide a mathematically unique solution. The second major problem in geophysical tomography is the necessity for detailed ray tracing. Commercial software, as well as previous U.S. Bureau of Mines (USBM) software, employs a ray-shooting algorithm that may be unable to model some ray paths when velocity contrasts are larger than about 100%. These ?shadow zones" result in loss of data and degradation of reconstructed images.

Jan 1, 1994

By K. E. Hjelmstad, W. H. Pomroy

In the event of fire underground, it is essential that all miners be warned as quickly as possible. With mine air rapidly depleted of oxygen and contaminated with smoke and toxic fire gases, any delay in the warning signal could have disastrous consequences. Unfortunately, present mine fire warning systems, such as stench, audible or visual alarms, telephones, and messengers, are often slow, unreliable, and limited in coverage. Recent research by the US Bureau of Mines has established the feasibility of ultralow frequency electromagnetic signaling for underground mine fire warning. Infield testing completed thus far at five mines, signals of from 630 Hz to 2000 Hz were transmitted through rock up to distances of 1645 m (5400 ft) to a pencil-sized ferrite-core receiving antenna and intrinsically safe receiver circuit. Theoretical analysis indicates a capability to transmit effectively for distances in excess of the maximum depths of most American mines, which is about 900 to 1000 m (2950 to 3280 ft) . The prototype system uses off-the-shelf components and state-of-the-art technology to ensure high reliability and low cost. This technology would enable simultaneous and instantaneous warning of all underground personnel, thereby in- creasing the likelihood of successfully evacuating a mine during a disaster. This report discusses the theoretical basis for through-the-rock ultralow frequency electromagnetic transmission, design of the prototype transmitter and receiver, and the results of in-mine tests of the prototype system.

Jan 1, 1991

By Henderson N, Schaap H

In large companies with mining operations spread over multiple sites, it is essential that consistency between sites is maintained in preparing and classifying resource and reserve estimates. The endorsement by The AusLMM and AMIC of the "Australasian Code for Reporting of Identified Mineral Resources and Ore Reserves" and the subsequent incorporation of reference to the code into the ASX listing rules for mining companies has provided a basis for the consistent classification of resources and reserves. However, compliance with other criteria more or less stringent than the Australasian Code can present some reporting difficulties. Examples include listing requirements for foreign stock exchanges, particular Acts of Parliament that may apply to individual leases, constraints imposed by individual companies on their own leases, and ultimately, reserves for short, medium and long term planning. Confusion can arise when any two or more sets of reserves for the same lease are compared.. To alleviate this confusion, a standardised procedure was developed for the calculation and classification of coal resources and reserves. The procedure which is geostatistically based incorporates a technique called "Irregular Block Kriging" where specific mining blocks are directly kriged. The procedure has enabled those engineers and geologists with only a basic understanding of geostatistics to apply the technique and not feel hampered by some of the complex mathematics which in the past has tended to inhibit and overcomplicate the use of geostatistics. The procedure has resulted in "cleaner" data bases and hence more reliable reserve estimates.

Jan 1, 1990

By N Meyer

This paper presents a research project referring to the stability of submerged walls of open pit mines and the actual state of development. Obviously the slope stability analysis is always a rather complex problem, because it is difficult to reduce the problem to a design scheme and to define the available in situ soil strength. Especially the design of submerged slopes represents a problem. The state-of-the-art slope stability analysis is based on a simplified modelling of slope failure and soil behaviour and with this predicted stable slope inclinations of sand slopes below water-table are less then half the angle of internal friction. Slope angles calculated like that canÆt satisfy the mining companies. One of the problems that have to be solved is the reliable determination of the long-term stability of non-cohesive, submerged slopes, which is not only dependant on geotechnical and hydrogeological parameters of the subsoil, but is also significantly influenced by how the slopes are made. The research project points at the relations between mining and geotechnical engineering with the main aim to find a more suitable stability analysis which takes both soil behaviour and mining influences into account.

Jan 1, 2003

Comalco Limited has recently completed construction of a $50 million kaolin plant at the site of its bauxite mining and industrial minerals operation at Weipa. The plant will produce 100,000 tonnes per annum of coating grade kaolin for the paper industry. Comalco produced the first coating kaolin from the deposit in 1979 on a trial basis. Since then a variety of quality coating grades with specific particle size distributions and brightness values have been prepared. Extensive drilling and bulk sampling of the deposit over eight years has shown that the ore body is large and of a high grade suitable for the production of premium quality coating kaolins. The processing plant technology was developed by Comalco in association with the European kaolin and equipment producer Amberger Kaolinwerke GmbH (AKW). The Weipa kaolin plant is the first of this size to be built in the Pacific Basin region and it will offer the region's paper-coating mills a stable and reliable source of high-quality kaolin, shipped from an established bulk loading port. The paper provides an overview of the development of the kaolin investment the nature of the production process and details the

Jan 1, 1986

Mines in the future deliver a paradigm shift in the way mining, material handling and processing are performed, unlocking significant value through production efficiency, flexibility and lower costs and enabling substantial safety and environmental benefits (V Schweikart). Mines in the future are highly productive, with low production costs and are significantly safer. They operate with a skeleton crew and use intelligent systems that fuse information from field instrumentation and other sources to generate the most efficient operating environment. Automated systems are seamlessly integrated across the mine and across the corporate enterprise. Geological models, long-term and short-term plans create optimised production schedules, suitably generated by the mine simulator. Production schedules are shared with the operations management system for deployment mainly by remotely operated and autonomous equipment. As the schedule is implemented, information is collected and shared with various plans, schedules, models and optimisation programs. This production environment is managed in real time from a æCentral Operations CentreÆ and it is visible across the business providing fast and accurate information about productivity, machine condition and environmental conditions. Central Operations Centres also house teams of subject matter experts that monitor and manage the mines and are able to communicate directly with the skeleton crew in the field. Constraints across the production line are displayed and managed appropriately from this location to maximise throughput. Maintenance is interactive and predictive. Reliability specialists in Central Operations Centres monitor the status of machinery and equipment and adjust maintenance plans and strategies to suit. Mining businesses rely heavily on knowledge workers û people with considerable knowledge and learning û and by manual workers. This new knowledge workforce is a team of associates rather than of bosses and subordinates. Field experts become leaders with tremendous autonomy regarding their work. The former line hierarchy becomes a support structure, intervening only in extreme emergencies; instead of giving orders, they are now removing barriers, expediting resources, conducting studies and acting as consultants.

Jan 1, 2009

By E. J. HOFFMAN, L. A. SCHOLL, J. c. W. FRAZER

The danger from coal dust in mines has been thoroughly demon- strated by experiment, and consequently the study of the inflam- mability of coal dust suspended in air, that is, the readiness with which a cloud of coal dust inflames, is of decided importance to those engaged in coal mining. Much knowledge has been gained from the work done in the large galleries constructed at official and semiofficial stations in this country and abroad, but the study of the coal-dust problem in these galleries requires so much time and is so costly that there is need of a reliable laboratory method for obtaining a classi- fication of the great variety of dusts that occur in mines. The investigation described in this paper was an attempt to devise such a method. It was a preliminary investigation, and work in the same direction is being continued by the Bureau of Mines. As Mr. Frazer has severed his connection with the bureau, it is deemed advisable to publish the results of his study substantially as he prepared them, with little attempt to draw conclusions or to show the bearing of the results on other studies now in progress. The results of these studies and a full discussion of the significance of the laboratory investiga- tions will be published in future reports of the Bureau of Mines. The reader should remember that any laboratory method, since it involves conditions that differ so greatly from those of actual mining, should be thoroughly tested, and the results obtained by it should be confirmed by experiments conducted on a scale simulating mining conditions before final conclusions are drawn. The need of a laboratory method has long been felt, and several investigators have devised apparatus and methods. The work done by Vital, Holtzwart and Von Meyer, Bedson and Widdas, Le Chate- lier, and that of the British Coal Dust Commission is of great interest in this connection. Bureau of Mines Bulletin 20 contains a sum-

Jan 1, 1913

By M Brewster

Goldfields Abosso Goldfields Limited (AGL) is a Ghanaian registered company that owns and operates the Damang Gold Mine. Gold Fields Ghana Holdings Limited holds a 71.1 per cent interest in AGL. The Damang concession held by Gold Fields Ghana Holdings Limited covers a total area of 271 km2 located 40 km north of the town of Tarkwa in the south-western part of Ghana. Gold Fields as a company registered on the New York Stock Exchange is legally obliged to be SOX (Sarbanes-Oxley). Sarbanes-Oxley Section 404 (SOX404) is on management assessment of internal controls. The Mineral Resource Management (MRM) function of AGL manages three Prospecting Licenses and two mining licences. At least ten pits/prospects are scattered along the two limbs of the Damang Anticline and have two main types of mineralisation notably Paleoplacer and Hydrothermal. Thus SOX404 procedures are put in place to treat each mineralisation type in the best way for reliable resource outputs and estimates. Generating auditable resources for AGL is a prime but most important function of MRM. Thus important checks are built and designed to ensure that all relevant geological and geostatistical inputs conform to procedures outlined under SOX404 requirements. More importantly sign offs are designed to ensure that technical personnel involved in all aspects of resource and reserve generation are satisfied and can be held accountable.

Jan 1, 2007

By E. F. Kingsbury

ONE of the well-known and important uses of the noble or precious metals has been for electrical contacts. In fact, the elements of this group, comprising gold, silver and the six platinum metals, have been called "noble" because of their ability to resist- heat and corrosion, properties which were early found to be of importance in good contacts. Of these, platinum and its iridium alloys, palladium, and silver, have been extensively used. In recent years the electrical industry has been responsible for about one-eighth of the total consumption of the platinum metals in the United States. Information is not available as to what part of this one-eighth has been used for contacts but it is certainly an important one. SUBSTITUTES FOR PLATINUM During the past 20 years a considerable number of contact alloys have been proposed in the patent literature largely with the aim of more or less replacing platinum by gold or silver, and some of these alloys are finding increasingly widespread application as the reliability of their performance becomes established.. From even the partial data at hand it appears that this substitution by the less precious metals has replaced at least one-half of the amount of platinum that the entire electrical industry would otherwise be consuming at the present time.

Jan 1, 1928

By Kugan Kuganathan

Pastefill is being increasingly considered as a viable fill by underground mine operators. Mount Isa Mines (MIM) chose pastefill to fill their deep copper mine (>1200m deep) after considering various other types of fill in the feasibility studies. During the development of pastefill at Mount Isa (1996 - to date) the Mining research of MIM developed two cost effective, reliable and simple testing methods and used. With the help of these tests the behaviour of MIM pastefill was studied thoroughly and the most optimum mix design for pastefill was achieved. The MIM's pastefill plant, the largest in the world with a capacity of 450rph continuous pastefill production and unique in the process used, has been built (1998-1999) to produce pastefill to the specification developed through extensive testing program using the Flow Cone and Mini Slump cone Tests. As a consequence, it is now possible to select the optimum pastefill mix designs and predict their flow behaviour in bore holes or pipe lines using only these tests. MIM Blended Tailings Pastefill (BTPF) uses 3-3.55 Portland cement and the cost of pastefill is much lower than the total tailings pastefill, that could be produced from the same tailings.

Jan 1, 2001

By C. W. Bollier

In recent years, Peabody Coal Company has enjoyed a great amount of success using roof trussing as a secondary support system. Since 1975, over 180,000 trusses have been installed in 12 different Peabody mines with varying geological conditions. Projections from Peabody, and throughout the mining industry, indicate a continuous growth in the trussing principle for roof control. Peabody's primary supplier has sold over 1,000,000 trusses to 50 different mines throughout the country. (1) Roof trusses provide an improved means of controlling difficult roof conditions which, in turn, improves worker safety and mine production. Since the original development of the truss, (2) the only major modification to the trussing procedure has been the addition of the resin point anchor system in the mid-70's. The resin point anchor was the catalyst needed to provide a reliable anchor and create acceptance of the roof truss by both management and labor. Peabody began using trusses in their mines in 1975. For the first few years, most of the truss effort was geared toward determining proper anchorage, spacing, and gathering historical data. In recent years, Peabody's activities have centered on the development of improving trussing procedures. Through monitoring and trussing activities, a number of areas of improvement have been found.

Jan 1, 1982

This paper examines the latest advances in mine drive and motor systems. In the last decade, the drive technology employed for large mine winders has migrated from the traditional dc technology to ac motors with cyclo convertor drives. Recent advances in pulse width modulation (PWM) drives have resulted in these being applied to large winder drives. While having many advantages for the winder system, the PWM drive must be carefully designed to ensure long-term reliable operation. When combined with induction motor technology, the PWM drive presents the ideal solution for winder drives. This paper examines the factors in choosing a suitable PWM drive for a winder installation. Factors under consideration include: winder duty cycle, drive rating restrictions, choice of power semiconductor device, cooling, and low speed operation.The cage induction motor is the motor of choice for large winder drives and has a number of advantages over the synchronous motor. The induction motor is ideally suited to integrated winder applications where the motor is built inside the friction drum, as installed at WMCÆs Olympic Dam site. The challenges of integrating the induction motor into the friction drum will be detailed, including: assembly, ventilation, air gap adjustment, and position sensors.

Jan 1, 2005

By D Newton

The Mt Morgan Minesite in Central Queensland has been subject to both underground and surface gold mining operations since the late-1800s. The site is largely unrehabilitated and poor quality surface run-off and subsurface leachate is contaminating the nearby Dee River. The site is dominated by a large open cut, which now stores contaminated surface and subsurface run-off. Three models were used to simulate the complex hydrologic processes occurring at the Mt Morgan Mine: a rainfall-run-off model, a groundwater model and a storage behavioural model. Study results showed that the open cut is filling with water and will soon spill large volumes of highly polluted water to the Dee River on a regular basis if no remedial action is taken. This will result in a three-fold increase in pollutant load to the Dee River. Based on a consideration of water quality and quantity it was concluded that the first priority for future minesite water management should be the prevention of spills from the open cut. Potential management options to achieve this objective included surface rehabilitation, catchment diversions, modification of the pump-back system and controlled releases to the Dee River during floods. However, assessing the relative effectiveness of these measures required a thorough understanding of the complex surface and subsurface hydrology of the site. The results of a 100 year simulation of hydrologic processes revealed that previously favoured management options would be ineffective in preventing spills to the river. On this basis, a continuous treat and release strategy was proposed as the only reliable method of preventing future spills. The results of this study demonstrate that good environmental management decisions must be based on an understanding of the relevant physical processes and consideration of cumulative effects over an appropriate time scale.

Jan 1, 2003