Search Documents

By Jasper Stuckey

THE object of this paper is to record and interpret field and laboratory observations made by the writers during five years of study of the barite deposits of North Carolina. Deposits of barite are known to occur in three localities in North Carolina (Fig. 1) two of which-the Hot Springs and Kings Mountain -contain material of economic value. The Hot Springs area begins near Bluff, some 6 miles south of Hot Springs, and continues northeast by Stackhouse; a total length of 7 miles. The Kings Mountain deposits lie along a belt that extends from the north end of Crowders Mountain in a southwestward direction, along the east side of this and Kings Mountain, to Kings Creek, South Carolina. The third locality is 3 1/2 miles southeast of Hillsboro, Orange County, a short distance west of the highway leading from Hillsboro to Chapel Hill. It is not known when barite was first discovered in North Carolina, but production from the Hot Springs area began some 50 years ago. The state has never produced large quantities of barite-usually there have been less than three producers-and definite figures are not available, but reasonably reliable estimates indicate a total production of 300,000 tons. From 1901 through 1920 barite mining was on a seemingly prosperous basis and a large tonnage. was shipped from the Hot Springs and Kings Mountain areas. With the depression of 1920 the industry began to decline and production practically ceased in 1926.

Jan 1, 1933

By Owen R. Rice

Changes in coke hardness affect the working of the blast furnace, for soft coke is an obstacle to proper furnace operation. Soft coke is due to a low hydrogen-oxygen ratio in the coal charged; increasing this ratio increases the hardness of the coke. The best means of determining the hardness of coke is the combined tumbler and ball-mill. What is Good Coke? It is not always appreciated that the correct answer may be such a reliable forecast to the physical condition of the blast furnace, and incidentally its entire operation, that among the ordinary variations in other raw materials and also in operating conditions, it assumes a position of primary significance. Inasmuch as coke forms two-thirds of the total bulk of material charged, this assertion will not seem exaggerated, and in the subsequent discussion its applicability will be presented. Coke is the ideal blast-furnace fuel because it is strong and hard enough to resist the crushing and grinding effects of the furnace burden, and its porosity allows the ready passage of gas upward through the charge, and rapid combustion before the tuyeres. Coke deprived of its strength and with a cell structure physically frail and chemically susceptible to solution by carbon dioxide has its chief asset eliminated. When the melting zones are approached the fluid cinder trickling toward the hearth will envelope the small pieces of coke and form a sticky mass that will retard the free passage of gas. Blast pressure will then rise, driving will slow up and fragments of coke will lie inert before the tuyeres, rendered practically incombustible by their slaggy envelop. It is believed also that coke messes at cast are attributable to quantities of such coke floating unburned in the hearth. It has been correctly claimed that coke rendered small outside the oven possesses greater combustibility than that so developed in the

Jan 1, 1922

By Finn E. Bronner

HISTORICAL PERSPECTIVE "Blessed be the Lord my strength, which teacheth my hands to war and my fingers to fight." Thus sang David three thousand years ago, in tacit acceptance of the condition of war, and in praise of the exceptional military skills with which this warrior king of Israel was endowed. He had cause to exult, for he had consolidated King Saul's conquests and added new ones of his own, not least of which was the capture of Jerusalem. David revealed in this operation that his mastery of the military arts embraced not only the weaponry and tactics of his day, but also strategy and that oldest of intelligence techniques: spies. The Jebusites, who built Jerusalem, had encompassed the city with the first of its many walls, but had neglected to incorporate the sole reliable water supply within its perimeter. This was Ain Gihon, today called the Fountain of the Virgin, which bubbled out on the east slope of Mount Ophel, one of the ridges on which Jerusalem was built, and drained eastward into the Kidron Valley. Water was brought into the city in the traditional manner: by women descending the stony trail outside the wall to fill their jars at the spring. But this essential daily activity was vulnerable to interruption by a hostile force outside the walls. To remedy this weakness, the Jebusites had driven a gallery from the spring a short distance into the water-bearing limestone under the city, and there cut a small collecting basin in the rock, a common way to develop springs throughout this arid region. But then the Jebusites dug a small vertical shaft from the roof of the gallery above the cistern upward about 15 m. From the upper end of this shaft, they constructed a narrow inclined tunnel with rock-cut steps leading up to the city streets. Thus the water supply could be reached even in time of siege.

Jan 1, 1979

By Eldon N. Dunlap

Recently the producing branch of the petroleum industry has shown a considerable and growing interest in the quantitative determination of the water, oil, and gas content of cores as it relates to estimation of reserves, to providing a basis for judging as to the feasibility of applying various secondary-recovery and pressure-maintenance processes, and in general to the operation of producing properties. For years it has been known that oil, gas and water coexisted in the pores of many semidepleted oil measures. It is now generally believed that oil-bearing beds contain connate water in amounts varying up to 50 per cent of the pore space. However, only lately has reliable direct evidence of the extensive occurrence of connate water in oil sands been published. Very little work has been done to ascertain the effect of this water on the productivity and ultimate recovery of oil from wells. It was the intent of this research to study the influence of interstitial water on the flow of oil through unconsolidated sands, with the hope that the results could be applied qualitatively to the flow of oil in underground reservoirs partly saturated with water. Obviously, ultimate recovery estimates based on the void volume of the reservoir will be in error unless a correction is made for the volume of water that occupies a portion of the effective pore volume of the reservoir. Evaluation engineers in the past have applied arbitrary saturation and recovery factors that may inadverently have compensated for the failure to consider specifically the water content. Nevertheless, the evidence available indicates that these factors need revising if each is to be independently correct and truly representative. Although the fact that the connate water renders part of the pore volume of the reservoir incapable of containing oil is of primary importance to the operator, it is also to his interest to know to what extent the presence of varying amounts of interstitial water influences the permeability of the sand to oil.

Jan 1, 1938

By Kenneth J. Kurry

12.2-1. Introduction. Successful management constantly strives to improve its methods and equipment in order to produce a better product at reduced cost. It is not enough that managers be cost conscious and industrious in these days of rapid, dramatic technological development. They must keep abreast of these developments-new or improved methods, machines, and equipment. Most of the machines and equipment have been carefully designed and perfected by reliable companies. However, improvements and progress often evolve from a definite need and are most successful in a particular operation. What may be the "answer" to the requirements of one company may be totally useless or inefficient to those of another. The manager of today must continuously evaluate the myriad proposals for change that result from modern technology-in terms of the particular needs and objectives of his company-to determine correctly which will best satisfy those needs and reach those objectives. Each new method or piece of equipment must receive careful study to make certain it is compatible with the entire operation. It may solve a problem in one department only to create a new problem in another. There are many pitfalls to be avoided in obtaining the necessary facts, and often these problems are unrelated to the actual use of the equipment or method being studied. All facets of the operation being considered must be thoroughly studied to determine if the method is compatible to the entire operation. For example, in considering a possible recommendation that a certain method and type of equipment be used to transport ore, some of the factors that should receive close scrutiny are: blasting procedure, maintenance, turning radius, percent grades, weather extremes, dumping problems, tire problems, length of haul, operator acceptance, or mismatched equipment. Failure to consider every factor-large and small, present and future-in evaluating a proposed change can mean a large investment in a new method or machine that will have to be continued for years at higher-than-antici-

Jan 1, 1968

Multi Torque Industries and Jadefoil have developed a safer, more efficient method of explosive protection, retention, placement, and constraint. In particular, this refers to advancements in airbag technology, where the system will offer an alternative to conventional gasbags and decking methods to provide a far more controlled and safer working environment. Airbags have provided operator control and reliability which has not until now been possible in this type of application. The benefits have been noted by current users and the advantages have provided an increase in productivity and significant savings in explosive waste. Obvious problems with gasbags lie in their instability in hot conditions where the danger is associated with gas canisters exploding with great force posing a significant risk to operators. Other problems associated with the decking systems currently on offer is the lack of versatility and operator control. The airbag systems give the operator full control to guarantee accurate placement, assured retention whilst boasting a quick operation of less than a few seconds for conventional void blocking, decking and plugging. One of the main advantages of the airbags is that the operator has full control over placement and retention force, therefore in wetter conditions where slippage can be a problem extra air can be added at the operatorÆs discretion to ensure a sufficient grip. Technical calculations coupled with experimental testing have demonstrated that an airbag will support the weight of a 30 m water column in an 89 mm hole at an initial bag pressure of 5 psig. Applications are increasingly growing whilst more customers embrace their use. Advancements such as the ability to deck in overhead holes, block voids in overhead holes at any depth, explosive retention in very wet conditions, longhole stabilisers to prevent hole closure and concertinaed liners reflect a dynamic potential for new technologies. All of these applications provide a decrease in explosive waste, an increase in operator safety, an increase in explosive protection, and an increase in productivity.

Jan 1, 2004

By Charles Macdonald

It may seem to be almost unnecessary to occupy the time of the Institute in further consideration of a question which has been so comprehensively treated in papers already on file in our own Transactions and in those of the American Society of Civil Engineers. Unfortunately, however, the results of these concerted efforts have not been materially to increase our stock of Knowledge in the direction sought for; and as the necessity for this information is becoming.more and more apparent as the demand for structural materials increases, it is believed that by continuing the agitation by means of discussions in this and kindred societies, whose members are vitally interested in obtaining reliable data as to the properties of the materials they are called upon to work with, public opinion may be educated up to the importance of exerting such an influence upon the law-makers of the country as will result in the formation of a competent board, with adequate means at its disposal, to carry out this great work in a manner alike acceptable to the makers and users of the materials in question. It may be proper in the first place to glance briefly at what has been attempted thus hr, then to indicate some of the more important lines of needed investigation, and finally to consider reasons why government aid may with propriety be sought for in carrying on the work. At a convention of the Society of Civil Engineers held at Chicago June 5th, 1872, it was, on motion of General William Sooy Smith, resolved, that, " Whereas, American engineers are now mainly dependent upon formula for the calculation of strength of the different form of iron and steel, not based on experiments upon American materials and manufacture; and " Whereas, There differ greatly in many of their ch~racteristics front thoae of foreign production, both in their nature and forma: therefore,

Jan 1, 1882

By R. C. Palmer

The testing of flotation oils has occupied a large part of the time of the testing departments of various companies using the flotation process in the beneficiation of their ores. The great differences in ores and in oils has made such work necessary, as it has not been possible to select the oil best suited for the purpose without trial of many kinds. In fact, individual shipments of flotation oils from the same manufacturer will often differ so radically that the mill men have been forced to test every lot of flotation oil before its use in the mills. Further, although almost every imaginable product of the distillation of wood, from alcohol to pitch, has been tested in a more or less perfunctory manner by various people, few companies have allowed the results of their tests to be made public. This work was undertaken for the purpose of obtaining reliable data regarding the value as flotation agents of a number of products that are obtained from the distillation of wood by different methods, and incidentally to determine whether some of the products not used at present could be used. Large quantities of such materials are being masted or burned in the wood-distillation plants of the United States, and if some use other than fuel could be found for these materials, such a use would represent a distinct saving to the country as a whole, would increase the profit of wood-distilling plants now operating and perhaps make it possible for others to operate which at present cannot do so except at a loss. At the same time it was thought that if such products can be used as flotation agents, then their use would serve to increase the number of oils and other products available for flotation purposes. It was also hoped that it might be possible to discover a substitute for some of the most effective but comparatively high-priced oils which are now used for flotation

Jan 1, 1917

By James Douglas

In discussing the waste upon which hinges, or is supposed to hinge, so largely the preservation of our national resources, the conclusions reached would be more reliable if actual experience were consulted, and fewer deductions were drawn from general statements, which are often the product of the imagination. It cannot be questioned that the value of by-products has .not been sufficiently appreciated by us, and that our tardiness in recovering the useful ingredients of the escaping gas of our coke-ovens is one of the most glaring instances of shortcoming in that direction. And yet even for that sin there is some palliation in the immature condition of affiliated industries. I presume that it is admitted, without argument, that, except under very exceptional conditions, all the elements cannot be recovered from most of the ores or natural products which we treat. While it is a shame that the by-products from our coke-ovens should be dissipated, Edward W. Parker's report to the U. S. Geological Survey for 19061 supplies a fairly good excuse in justification of this appalling waste. He says (pp. 773 to 774.): " What has been already commented on in previous reports about the slowness of manufacturers to change from the better known but wasteful beehive practice to the by-product recovery method of coke manufacture is particularly emphasized in the statistics presented in this chapter. For it would appear from the table following that the construction of by-product ovens had about come to a standstill, especially when the records for the preceding five years are taken into consideration. At the close of 1901, when there were only 1,165 by-product ovens completed in the United States, there were 1,533 in course of construction, 498 of which were completed during the following year. At the close of 1902, 1,346 retort ovens were building, 293 of which were added to the completed plants in 1903. At the close of 1903, 1,335 new ovens were building and 954 of these

Jan 1, 1910

By Owen R. Rice

Changes in coke hardness affect the working of the blast furnace, for soft coke is an obstacle to proper furnace operation. Soft coke is due to a low hydrogen-oxygen ratio in the coal charged; increasing this ratio increases the hardness of the coke. The best means of determining the hardness of coke is the combined tumbler and ball-mill. What is Good Coke? It is not always appreciated that the correct answer may be such a reliable forecast to the physical condition of the blast furnace, and incidentally its entire operation, that among the ordinary variations in other raw materials and also in operating conditions, it assumes a position of primary significance. Inasmuch as coke forms two-thirds of the total bulk of material charged, this assertion will not seem exaggerated, and in the subsequent discussion its applicability will be presented. Coke is the ideal blast-furnace fuel because it is strong and hard enough to resist the crushing and grinding effects of the furnace burden, and its porosity allows the ready passage of gas upward through the charge, and rapid combustion before the tuyeres. Coke deprived of its strength and with a cell structure physically frail and chemically susceptible to solution by carbon dioxide has its chief asset eliminated. When the melting zones are approached the fluid cinder trickling toward the hearth will envelope the small pieces of coke and form a sticky mass that will retard the free passage of gas. Blast pressure will then rise, driving will slow up and fragments of coke will lie inert before the tuyeres, rendered practically incombustible by their slaggy envelop. It is believed also that coke messes at cast are attributable to quantities of such coke floating unburned in the hearth. It has been correctly claimed that coke rendered small outside the oven possesses greater combustibility than that so developed in the

Jan 1, 1922

By B. E. Fernow

MINING interests in the Western mountains are very seriously affected by the danger to property and life from destructive snowslides and avalanches. This is a danger which the miner has largely brought upon himself by an improvident stripping of the timber from the mountain slopes, and, therefore, he might be expected to take an interest in the reforestation of the areas thus devastated. A canvass was lately undertaken by the writer to ascertain approximately the extent of the damage suffered from this source, but the difficulty of obtaining reliable data has proved too great to permit, as yet, even an approximation. So much, however, is certain : that the loss of life is considerable, and that much property is destroyed almost every winter. True, neither the number of avalanches, nor their destructiveness, nor the amount of loss compares with what Switzerland experiences. This is due not only to the greater precipitousness of the Alps and to different climatic conditions, but also to the fact that in Switzerland a larger number of settlements is exposed to these dangers. A very complete and interesting official report on the very numerous and destructive avalanches occurring in Switzerland during the season of 1887-1888 has just been published as a contribution to the inquiry, whether and how these dangers can be averted. Peculiar weather-conditions, in addition to heavy falls of snow, were the reasons for the frequency of the phenomenon during that winter. This report records 1094 avalauches, by which 850 houses were destroyed or severely damaged; 84 persons and 752 cattle were buried; traffic on railroads and on highways was greatly interrupted, and the damage to personal property alone was valued at over $100,000. One of these snow-masses covered about half an acre, with a cone 250 feet in height. During the same year in Tyrol the number of avalanches was 3647. Of these 1355 run over permanent beds; that is, they recur annually, so that they are

Jan 1, 1890

By K. C. Carriere

INTRODUCTION The purpose of this section is to introduce the reader to the concepts of computer control of grinding circuits, and to flag some of the opportunities to be encountered, but without becoming overly involved in details of process, equipment or software. It is assumed that the reader has some familiarity with computer hardware and software, and in particular with the grinding process. The paper is organized into four parts: a general commentary of the need for computer control of grinding, a discussion of the process considerations involved, a more detailed elaboration on the current state of applicable computer technology, and a case study indicating one approach towards such a project. A brief installation survey and references for further reading are also given. This section will primarily deal with supervisory computer applications. Direct Digital Control and microprocessor systems are generally used as replacements for analog controls and thus are not considered in depth. Many configurations of grinding circuits exist, necessitating certain assumptions. Since many new concentrators use an open circuited SAG mill feeding a closed circuit ball mill, this configuration is used as a model although the principles stated can be extrapolated to any circuit. Motivation The use of computers for industrial control has been one of the dreams of control engineers and operators alike for many years. The concept of a plant running at optimal conditions with minimal operator involvement is very attractive from economic and technical standpoints. Accomplishment of this goal has been a long struggle, but today likelihood of success of such a project is very high, considering the reliability of modern hardware and the sophistication of available software. The primary motivation of any control system must be economic, i.e. it must pay for itself and make money for the owner, directly or indirectly. In grinding control the benefits which can be expected include: a) Higher through-put b) More uniform product in particle size, density and volumetric flog: c) Reduced operating costs including media consumption, power consumption and liner wear

Jan 1, 1982

By Graham Bright

Before the arrival of central-station power, all coal and metal mines generated their own power and, in many cases, these isolated power plants gave a fair continuity of service. In coal mines that produce considerable gas, it is essential that power be available at all times for operating the ventilating fan and the hoist, if the mine is of the shaft type. In the case of an isolated power plant, if trouble should develop with the fan the men can be hoisted quickly when the mine is of the shaft type. On the other hand, if trouble develops with the hoist, the fan can be kept in operation, and there will be no necessity of haste in getting the men from the mine. Now that central-station power is being used so extensively for mine service, the continuity of service with gaseous mines is very important. : Inherently, the central station is much more reliable than any isolated plant, but trouble may occur on the transmission lines which may prevent the transmission of power for a considerable time. : Some mines have kept their steam equipment intact and ready for operation in case the purchased power should fail. This is expensive procedure, for the boiler plant must be fired at all times so that the emergency power will be quickly available. In a number of instances, gasoline-engine driven generators have been installed to furnish emergency power for the service hoist. As most service hoists are of the alternating-current type, the generator of the gasoline-engine driven set is usually of the a.c. type and is arranged to drive the service hoist motor at full speed, or an extra motor that can be thrown into gear on either the main or service hoist and the hoist operated at a greatly reduced speed. This arrangement is used because it is difficult and expensive to obtain and install large gasoline-engine driven units. The author has recently developed a plan by which the main hoist and the fan can both be operated at reduced speeds, in case of loss of power from a central-station power system. In this plan a gasoline-engine

Jan 1, 1923

By Sylvain J. Pirson

The main value of earth magnetic measurements, outside of certain mining problems, resides in the study of deeply buried tectonic phenomena related to regional and local geology. Magnetic surveys are a necessary complement of gravimetric measurements, especially of pendulum surveys. To date, magnetometer prospecting has been used chiefly in the study of sedimentary basins where petroleum structures are associated with the uplifted basement rocks. There are, in the literature, innumerable articles dealing with such surveys as applied to oil geology but few treat of broad geological features related to regional magnetic disturbances of the earth field. An important piece of coordination work has been made by Jean Jungl for the magnetic and gravimetric measurements made in France and their geologic significance. A similar attempt at correlation of the known geology with the anomalies of the vertical component of the earth magnetic field has been made for the United States by George B. Somers2. Taking the magnetic vector as a whole, W. P. Jenny3 made a coordination of magnetism and geology for the main producing oil states of the United States. A more detailed study along the same lines is published by A. Van Weelden4 for southern Oklahoma and northern Texas; in this work magnetic and gravimetric measurements taken at stations as close as one mile apart are compiled and compared to the regional geology of the Ouachita-Amarillo uplifted area. From the literature mentioned, it is evident that reliable interpretation of magnetic' anomalies can be arrived at only when the magnetic stations are numerous and cover the area in a close net of measurements, therefore the works of Somers and Jenny, based on sparsely distributed Government measurements, can be regarded only as preliminary programs indicating lines along which further work should be done, whereas the coordination made by Van Weelden is an example of the contribution to the knowledge of regional geology that can be arrived at by the use of applied geophysics. With the hope that further systematic magnetic measurements will be carried on to solve regional and local geological problems, the author

Jan 1, 1940

By J. R. Woolsey, B. G. Noakes

A prototype remote placer drill (RPD) has been designed and successfully tested in the offshore gold district of Nome, AK. The RPD system is unique in its design and in the cooperative support that was provided during its development by industry, academia and government. The RPD was conceived as a low-cost, rapid drill sampling system for the reconnaissance of marine precious metal placer deposits. The drill functions as a counter- f lush system. It incorporates a dual wall casing and a rotating percussion bit driven by way of a drill rod through the central eductor casing by a heavy duty pneumatic rock drill. The cost of drill sampling in the exploration of marine precious metal placers has traditionally been high due to the technical difficulties imposed by the environment and the remoteness of the sampling target. The objective was to reduce capital and operating costs of a drilling program through the development of a portable system incorporating drill compoments having a high power-weight ratio that could be deployed from work vessels of opportunity. A principal design requirement was to operate the system remotely from the sea floor with only flexible connections to the surface. This includes cable for deployment and retrieval and hoses for air supply and sample recovery, thus making the drill system semi-independent of the vessel's sea-induced motion. The prototype RPD underwent full operational test off Nome, AK in late summer 1988. It was deployed from the landing door of a modified LCT vessel, and rigged for a single pass of 5 m (16.5 ft). More than 50 holes were drilled in a wide variety of bottom materials typical of the off shore Nome submerged beach placers. The prototype RPD proved to be an overall success, recovering representative samples throughout the section in all but the heavy boulder ground. Compared with a conventional drill system on board that was assigned to a production drilling system, the RPD was capable of reliably sampling moderate ground less than 6 m (20 ft) in thickness, using a smaller crew and operating in higher sea conditions.

Jan 1, 1991

By Sylvain J. Pirson

The main value of earth magnetic measurements, outside of certain mining problems, resides in the study of deeply buried tectonic phenomena related to regional and local geology. Magnetic surveys are a necessary complement of gravimetric measurements, especially of pendulum surveys. To date, magnetometer prospecting has been used chiefly in the study of sedimentary basins where petroleum structures are associated with the uplifted basement rocks. There are, in the literature, innumerable articles dealing with such surveys as applied to oil geology but few treat of broad geological features related to regional magnetic disturbances of the earth field. An important piece of coordination work has been made by Jean Jungl for the magnetic and gravimetric measurements made in France and their geologic significance. A similar attempt at correlation of the known geology with the anomalies of the vertical component of the earth magnetic field has been made for the United States by George B. Somers2. Taking the magnetic vector as a whole, W. P. Jenny3 made a coordination of magnetism and geology for the main producing oil states of the United States. A more detailed study along the same lines is published by A. Van Weelden4 for southern Oklahoma and northern Texas; in this work magnetic and gravimetric measurements taken at stations as close as one mile apart are compiled and compared to the regional geology of the Ouachita-Amarillo uplifted area. From the literature mentioned, it is evident that reliable interpretation of magnetic' anomalies can be arrived at only when the magnetic stations are numerous and cover the area in a close net of measurements, therefore the works of Somers and Jenny, based on sparsely distributed Government measurements, can be regarded only as preliminary programs indicating lines along which further work should be done, whereas the coordination made by Van Weelden is an example of the contribution to the knowledge of regional geology that can be arrived at by the use of applied geophysics. With the hope that further systematic magnetic measurements will be carried on to solve regional and local geological problems, the author

Jan 1, 1940

By Robert L. Virta

An asbestos substitute is any material that replaces asbestos in a commercial product. There are many asbestos substitutes, each with its own unique physical and chemical properties. Substitutes can be inorganic or organic, fibrous or nonfibrous, and natural or synthetic. They also can be used as a direct substitute for asbestos or as a replacement product. Probably in no other field is the diversity of substitute materials so great. The concept of asbestos substitutes is not new. The first major effort to develop asbestos substitutes was undertaken by the federal government. The United States has always been dependent on foreign sources for strategic-grade asbestos, and during World War II, the government was concerned that these supplies would be cut off. Strategic-grade asbestos was critical in many electrical and thermal insulation applications (electrical insulation, battery plate separators, flame-proof boards, insulation for rocket components, etc.). A reliable supply of nonstrategic-grade asbestos also was required for general civilian and military applications, such as in brakes, clutches, and construction materials. The government not only initiated a major search for deposits containing strategic-grade asbestos, it also funded research on synthesizing asbestos in the laboratory and developing products that did not contain strategic- grade asbestos. These efforts, as well as those conducted by the private sector, generally were unsuccessful. In the late 1960s and early 1970s, a second major effort to develop asbestos substitutes began because the general public was concerned about the health threat posed by the release of asbestos fibers during the manufacture, use, repair, and disposal of asbestos-containing products. Strict regulations covering the mining and manufacturing sector already had been enacted because of the issue of occupational exposure. The issue then became environmental exposures. Environmental regulations were enacted, and through time they became more strict. The combination of increasingly strict environmental regulation, maturing of some asbestos markets, and liability issues prompted many manufacturers to discontinue asbestos product lines or search for asbestos substitutes. As a result, asbestos usage dramatically declined from the 1970s to the present (Table 1).

Jan 1, 1994

By George Bockosh

Mr. Bockosh is an electrical engineer with the U.S. Bureau of Mines In Pittsburgh, and has devoted the last two years to research on underground illumination. He formerly was a mine maintenance foreman and worked two years underground. He is a graduate of the University of Pittsburgh, where he is now working toward his masters degree in mining. When Congress first legislated light in American coal mines, it was a little like mandating a walk on the moon before the first satellite had been put in orbit. It was never a question, of course, of whether it could be done. But no one knew quite how. It's one thing to string a few light bulbs, and quite something else to provide uniform, sufficient, safe and reliable illumination, with fixtures that will hold up under some of the toughest conditions in the world - in the life-and-death circumstances of a craggy, black cavern filled with dangerous, moving machinery. In fact, in 1969 when Congress originally mandated illumination standards for the work places of underground coal mines, no one even knew just how much light was needed. That question was answered within a year by the National Bureau of Standards. In a study commissioned by the U.S. Bureau of Mines, the Bureau of Standards determined that underground mine should be illuminated with a light intensity of 0.06 foot-lamberts, a measurement of light reflected from surfaces in the lighted area-as opposed to foot-candles, a measurement of light from the source of illumination-in order for miners to adequately see what they are doing. That study was followed by more detailed research done at the Bureau of Mines' direction by the Research and Development Department of the Naval Ammunition Depot in Crane, Ind. This work evaluated the specific lighting needs of miners engaged In more than 100 different job tasks in all three types of coal mining- conventional, continuous and longwall. The Naval Depot report brought forth nearly 300 pages of detailed lighting data and concluded that proper illumination of mine work areas would serve more than just the cause of mine safety.

Jan 1, 1976

By J Watson

Electronic detonator technology has been under development for the last two decades. Currently, there are a number of systems commercially available with several others still under development, each with its own unique features. This technology can offer a significant advantage to the drill and blast engineer through their ability to initiate an explosive charge at the æplannedÆ time. This new technology has created huge interest within the drill and blast community and also raised their expectations to produce better blasting outcomes. In many cases, specifications (or even expectations) of desired blast results are not properly defined. Interaction between the input variables (rock mass characteristics and blast design) and results (fragmentation, throw, damage, ground vibrations, etc) and their mechanisms, or relationship to one another, are not very well defined or understood. That is why rock blasting is still considered by many as an art rather than science. With one of the few remaining variables (cap scatter) now controllable, todayÆs blaster finally has the ability to apply science to his trade. Even though electronic detonators are available and becoming more commonly used, current field practices are not always conducive to extracting or deriving the maximum benefit from this new technology. In the authorÆs opinion, the following need to be understood to derive and sustain the maximum value: clear definition or specification(s) of desired outcomes from a given blast; impact of different features in an electronic detonator system (precision, accuracy, flexibility, reliability, etc) and their impact on the desired blasting outcomes; interaction of blast design variables (energy, energy distribution, timing, blast geometry) and their impact on desired outcomes; impact of rock mass variability and quality of blast implementation on the desired blasting outcomes; and critical need to utlilise appropriate tools and systems in order to measure and quantify benefits.In the authorÆs opinion a scientific implementation process is the key to derive the benefits. This paper analyses the industryÆs preparedness to derive the benefits from this technology and proposes a scientific methodology to understand, evaluate and sustain the value from this technology.

Jan 1, 2004

By Graham Bright

Before the arrival of central-station power, all coal and metal mines generated their own power and, in many cases, these isolated power plants gave a fair continuity of service. In coal mines that produce considerable gas, it is essential that power be available at all times for operating the ventilating fan and the hoist, if the mine is of the shaft type. In the case of an isolated power plant, if trouble should develop with the fan the men can be hoisted quickly when the mine is of the shaft type. On the other hand, if trouble develops with the hoist, the fan can be kept in operation, and there will be no necessity of haste in getting the men from the mine. Now that central-station power is being used so extensively for mine service, the continuity of service with gaseous mines is very important. : Inherently, the central station is much more reliable than any isolated plant, but trouble may occur on the transmission lines which may prevent the transmission of power for a considerable time. : Some mines have kept their steam equipment intact and ready for operation in case the purchased power should fail. This is expensive procedure, for the boiler plant must be fired at all times so that the emergency power will be quickly available. In a number of instances, gasoline-engine driven generators have been installed to furnish emergency power for the service hoist. As most service hoists are of the alternating-current type, the generator of the gasoline-engine driven set is usually of the a.c. type and is arranged to drive the service hoist motor at full speed, or an extra motor that can be thrown into gear on either the main or service hoist and the hoist operated at a greatly reduced speed. This arrangement is used because it is difficult and expensive to obtain and install large gasoline-engine driven units. The author has recently developed a plan by which the main hoist and the fan can both be operated at reduced speeds, in case of loss of power from a central-station power system. In this plan a gasoline-engine

Jan 1, 1923