Search Documents

By William E. Schoeneck

This paper presents the problem of oil-well abandonment as a group of studies involving the compilation of physical well data, the use of special curves, maps, and interpretative Procedures, in order that operations can be analyzed and means for reducing costs can be effected. Methods for the calculation of the economic limit of production and resultant oil reserves are suggested in order that profitable production may be continued and premature abandonment prevented. INTRODUCTION Purpose Extensive studies have been made and much has been written on the procedures for prospecting, drilling, completion, production and repair of oil wells, but the writer has long felt the need for a study of the procedure that should be followed when considering the abandonment of a well. The production from numerous well bores of a fluid material (a circumstance peculiar to the oil industry) that is continually decreasing in quantity leads to an increasing ratio of operating cost to production. It is for this reason that oil fields are not abandoned as a whole and detailed consideration of each well is required before it can be determined whether more is being expended than will be returned On any well or lease in question. It is the purpose of this paper, therefore, to compile, correlate, and present all matters worthy of consideration in the problem of oil-well abandonment; to suggest interpretative procedures based on such compilations, to the end that reliable estimates of reserves and life may be obtained; to show, as a result of such interpretative procedures, the possibilities for corrective measures conducive to economical production, thereby extending both profitable reserves and length of life. Scope and Approach Compiling data and outlining a study having the complexity of the problem at hand are naturally subject to the personal experiences of one who undertakes the study; however, the chosen approach and grouping of the subject material may be helpful in the consideration of abandonment problems. Consideration has been given to wells that make gas and water incident with the production of oil; but consideration has not been given to either gas wells or condensate-producing wells, for wells of the latter type have sufficient problems to warrant separate investigation. The major subdivisions of this paper-— physical considerations and economic considerations—do not imply that either of these phases can be considered independently, but rather that the two are mutually dependent and are the component parts of an engineering study.

Jan 1, 1946

By W. H. Young, P. D. Torrey

The Eastern fields comprise a distinct geological and geographical unit, located in the northern part of the Appalachian geosynclinal prov-ince. In this area are the fields of New York, producing from rocks of Devonian, Silurian and Ordovician age; the fields of western Pennsylvania, where oil and gas occur chiefly in rocks of Mississippian and Devonian age; the fields of eastern Ohio, where oil and gas are obtained from rocks of Pennsylvanian, Mississippian and Silurian age; and the fields of West Virginia, where oil and gas are produced from rocks of Pennsylvanian, Mississippian and Devonian age. Many of these fields are of great antiquity in comparison to the age of the producing areas in a greater part of this country, and consequently in most instances it is impossible to obtain accurate historical statistics. In addition, the records of many of the more recently discovered fields are either unobtainable or are not sufficiently reliable to justify their incorporation in a review of this character. Rather than overemphasize certain fields and areas, where complete records are available, when there are many other fields of equal importance for which statistical data are not available, the authors have made a tabulation of development that does not take into consideration past operations and production. The records utilized in preparing this paper were derived largely from the scout reports of several of the larger companies, which generously made them available to the authors. These were independently tabulated by counties and townships, in order to eliminate as far as possible duplications and, excepting the Clinton fields of Ohio, where many of the smaller wells have not been individually reported, they represent the most accurate information available. Market conditions in both the oil and gas industry were far from favorable during 1932 and in consequence there was a total decline in drilling in the Eastern States, which is 22 per cent less than the number of completions in the preceding year. This decline was not constant over the entire area, as is shown in Table 1. The oil fields of both New York and western Pennsylvania were the scene of renewed drilling activity, which was largely restricted to the water-flooding operations in the Bradford and Allegany fields. Practically no new operations were started, but a certain number of new wells

Jan 1, 1933

By R. E. Wade

The Butte, Anaconda & Pacific electrification is of peculiar interest, in an incidental way, to the entire mining fraternity, and especially the engineering branch, not only in this great Northwest country but throughout the entire Western mining country, which is rich in minerals and water power. It is probably fair to say that the prime object of mining and smelting engineering is to reduce the cost of production, and in the case in hand the relative location of mines and smelter brings the cost of transportation of ore to the front. While some might assign this item to the railway people, it is inseparably a part and parcel of the general scheme of the production of metal from the ore. In considering the electrification of the B., A. & P. railway the mining and smelting engineer, above all, wants to know what saving will be effected by the change in motive power. Unfortunately the new power has been in use during a very limited period and on the Smelter Hill section of the road only, and no reliable data, from actual service conditions, can be obtained until the entire electrified section has been in service for a reasonable length of time. Any remarks on this subject at the present time, therefore, must of necessity be general in nature and more or less descriptive. The railway, electrical and mining worlds and the country in general are indebted to the B., A. & P. railway for the pioneer work it is now doing, as it undoubtedly marks the beginning of the electrification, within the comparatively near future, of all transcontinental roads between the Missouri river and the Pacific coast. Together with this goes the development of an untold wealth in water power and all natural resources within the same territory. For the first time in the history of electric railway work, in this country, direct current at a potential of 2,400 volts is being used. With this potential there is a great saving in transmission of energy to the locomotives and there are only two substations, one at either end and 26 miles apart, for supplying the power for the movement of trains of heavy tonnage over the main line and for switching movements at terminal and intermediate yards, and comparatively little feeder copper is required.

Jan 1, 1914

By E. R. Parker, T. H. Hazlett

An understanding of the mechanism of creep of metals requires an accurate knowledge of shape of the time-deformation curve. An expression is developed which accurately expresses the creep curve for a number of structurally stable metals and alloys. VAST strides have been made in the development of high temperature creep resistant alloys; however, no sound understanding of the physical mechanism of creep exists to date. Consequently, creep resistant alloys are still developed by "cut and try" methods formerly so successful but now yielding returns at a continuously diminishing rate. It is apparent to all workers in the field that if the mechanism of creep were understood, much fruitless labor could be avoided. The dirth of fundamental knowledge has not discouraged the theorists. Speculation has flourished and numerous theories of creep have been proposed. A critical review of these theories reveals that, even though there are some general areas of agreement between the majority of the workers, there are many basic questions yet to be resolved.' It is generally conceded that theoretical speculation is far in advance of experimental evidence. The shortage of reliable creep data greatly hinders more rapid progress in this field. It is essential that the effects of different stresses and temperatures on the creep characteristics of metals be quantitatively determined. Once this has been accomplished, it will then be possible to evaluate the effects of alloying additions and, it is hoped, to provide a firm basis of facts for theoretical treatment of the creep phenomenon. The work reported herein was undertaken to determine the effects of such variables as stress, temperature, alloying, and structure on the creep characteristics of some metals. Material and Equipment Nickel was selected as the base material for the current investigation and an experimental program was initiated to determine the effects of temperature and stress on the creep characteristics of this material. Since a large quantity of high purity nickel was required for the proposed program and such material was not commercially available, it was decided to refine, cast, and prepare the required metal in our own laboratory. The resulting nickel test bars had the following composition, given in percentage by weight: Fe, 0.030 (1); Si, 0.003 (2); Ca, 0.001 (1); Mg, 0.020 (2); and S, 0.002 (2); to make total impurities of 0.056. The nickel (balance by difference) is 99.944 pct. The details of the purification process are described elsewhere.' This

Jan 1, 1954

By P. I. Page

In mineral exploration the place that yields the first significant result is marked and two questions are posed immediately. Where should the next sample be drawn and how big should it be? At present the answers are arbitrary and ad hoc. They depend on personal experience and sentiment?that is hunch. The thought processes involved in reaching the decisions are unsatisfactory and unsatisfying for professionals. This paper proposes guidance on choosing sample spacing and sample size. The guidance is obtained from the grades of the samples. The grades also imply the extent of influence of each sample assay. Thus sampling and assay are integrated. The integration is achieved by changing the unit of value in which assays and grades are expressed and by exposing meanings and functions of grade beyond that of measuring rock value. The proposals are extended to guide comminution of particle size in sample size reduction and to deal with the problem of erratic high assays. Also, elucidation becomes possible of the computation of a reliable figure for average grade as a statistical weighted mean.

Jan 1, 2005

By N. L. Hayward, V. H. Ness

In the past decade Australia has seen the development, construction and commissioning of three complex processing plants for the treatment of lateritic nickel ores. These have all been based on high pressure acid leaching (HPAL) for extraction of nickel and cobalt into solution, followed by solid liquid separation in a CCD circuit. However, flowsheets for separation and purification of the nickel and cobalt diverge markedly. The existing plants have been commissioned with varying degrees of success, with a variety of problems ranging from materials of construction to inadequate design. While the process problems are not insurmountable, there is much room for improvement. Currently there are several new HPAL plants at the feasibility or financing stage. All of these have adopted one of the existing flowsheets. Most of the enhancements have focused on increasing autoclave size. It is now time to assess the success and failures of the three existing plants and incorporate this experience in a design for productivity, efficiency and reliability. Towards this end, this paper discusses aspects of flowsheet optimization, materials of construction and engineering design.

Jan 1, 2001

By C. W. Greenhalgh

THE accuracy with which grade and tonnage of a mineral deposit may be calculated from diamond-drill assays is dependent upon: (I) the reliability of core and sludge samples and (2) the validity of methods used in grade and tonnage calculations. Limitations imposed by drilling and sampling preclude elaborate methods of computation. In adjusting core and sludge assays the importance assigned the core and sludge samples may be based on either the respective weights recovered or the respective volumes represented by each. Only when core and sludge recoveries are poor do discrepancies between adjusted assays calculated by these two methods develop, in which case the "weight" method gives emphasis to the core sample and the "volume" method gives emphasis to the sludge sample. When the sludge suffers classification within the drill hole, the weight method gives more accurate results; when the sludge sample suffers no classification, the volume method gives more accurate results. Any drilling campaign offers a compromise between desired accuracy on the one hand and expediency, limited time, money, or facilities on the other. Since the determination of grade and tonnage is an approximation at best, a proper basis for their computation requires a knowledge of the limitations imposed by all phases of work upon which the calculations depend. A rational basis for coordination of these phases of work requires determination of: (I) the degree of accuracy desired, as a function of the object of examination; (2) the degree of accuracy attainable, as a function of the limitations imposed in the drilling and sampling program; and (3) the validity of method to be used in calculating grade and tonnage from core and sludge assays. This paper presents results of a comparison made between two commonly used methods of adjusting core and sludge assays, the assumptions upon which these methods are based, and the interrelationship of the phases of work upon which these calculations are dependent. OBJECT OF EXAMINATION The purpose of prospecting any mineral deposit is to secure sufficient samples from which ore grade and tonnage may be calculated. Any mine examination, preliminary or formal, has a definite purpose, although its scope may be limited or broad. The type of examination to be conducted is dependent, therefore, upon the reason for instituting the investigation; its scope and thoroughness are directly related to economic considerations. It is highly desirable, therefore, that before starting a drilling campaign a complete understanding of the extent of examination and desired degree of accuracy be determined as a means of simplifying the drilling program and unifying the relative degree of

Jan 1, 1946

Of all of the processes in the mining cycle, blasting has the greatest impact on the efficiency of both mining itself and the initial stages of ore processing. The cost of blasting can be readily accounted for, but the true benefits of an effective blasting operation are seldom measured or reported. This means that blasting is seldom optimised in terms of its overall economic impact on an operation. Blasting operations have evolved according to the environment provided by mine management. Most operations seek to minimise the unit cost of each component process (overburden removal, blasting, excavation and transport, crushing or grinding) without recognising the impact that blasting performance has on subsequent activities. The creation of æcost centresÆ or æmanagement unitsÆ that isolate blasting from its downstream impacts reinforce this trend. Modern blasting technology is regarded as sophisticated by virtue of the mechanical design of the drills, the chemistry of the explosives and the flexibility and reliability of modern blast initiation systems. However, blast performance is controlled by the nature of the rock mass and there is generally an inadequate appreciation of how blast designs should be tailored to suit different rock mass conditions or to meet different blasting objectives. Most operations utilise a limited suite of standard designs without routinely tailoring designs to suit the actual conditions at hand or the objectives of each blast. Mining operations would benefit from tackling the following specific challenges:What is the appropriate target performance for blasting operations to generate the maximum economic benefit for the operation as a whole? How should designs be configured to suit the changing rock mass conditions and operating constraints? What compromise (if any) should be allowed from the ideal to assist conflicting scheduling or other operational requirements? How can blast performance be measured and reported to provide appropriate guidance to future operations? These challenges can be tackled through the process of æblast engineeringÆ. This paper discusses the potential impact of blasting performance on the economics of mining operations and the author argues that very considerable benefits over and above those currently being achieved could be realised by improving the routine engineering of mine blasts. The paper then explores how the industryÆs failure to recognise the economic importance of blasting has resulted in the engineering of blasting operations receiving less management and technical support than is appropriate. Finally, a simple approach to the engineering of routine blasting operations is described as an example of how these challenges can be tackled.

Jan 1, 1999

By P. C. Schutte, A. J. Kielblock

INTRODUCTION Certain activities, such as emergency work and rescue operations, often have to be undertaken in environments where heat loads often exceed limits prescribed for routine work. This is particularly relevant to the South African mining industry where heat stress-induced fatalities are not uncommon during rescue operations. In this regard an excessively hot environment is defined as one where either the dry-bulb temperature exceeds 37,0°C or the wet-bulb temperature exceeds 32,5"C, and it is therefore not surprising that heat stroke mortality escalates rapidly when these limits are exceeded. A review of both local and international standards indicated that the available information on safe exposure times under abnormal heat stress conditions is very limited. Where available, such standards are aimed at the general population, including both sexes, irrespective of age and also the least heat tolerant worker, and not at a medically-screened, all-male population free of grossly heat intolerant individuals, as is the case in the South African mining industry. It is suggested that available norms and limits are too conservative for local application and, therefore, unrealistic. In view of the definite need to protect workers when exposed to abnormally high environmental temperatures, the present study was undertaken to establish a scientifically derived data base. applicable to local conditions, to determine safe exposure times: Any exposure limit, especially in an emergency situation, should be easy to administer, valid and reliable. These aspects, there- fore, form an integral part of this paper. FORMULATION OF HEAT STRESS LIMITS The formulation of heat stress limits was based on the criterion that a heat exposed individual should experience a negligible risk of developing dangerously elevated body temperatures. In order to provide a database for risk assessment, certain physiological responses of heat tolerant men were determined at various combinations of thermal conditions and work rate in a climatic chamber. These physiological responses were analysed statistically in order to predict safe survival and tolerance times as a function of thermal conditions and work rate. EXPERIMENTAL DESIGN A total of 202 randomly selected, medically fit mine workers volunteered for the study on the basis of informed consent. These men were considered to be inherently heat tolerant in as far as they had successfully completed a heat tolerance test (Anon., 1991) or the standard climatic room acclimatisation procedure used on many South African gold mines (Anon., 1989). The subjects were allocated randomly to 14 experimental groups and each group was exposed in a climatic room to one of

Jan 1, 1997

By Hans W. Schreiber

INTRODUCTION At the end of the day, the decision by the sponsor to proceed with a project and to seek financing, or the decision by the financier to grant financing are made on a judgmental basis. Cash flow projections, sensitivity and risk analysis, the innumerable ratios applied by the financier, the so-called feasibility study, etc. are all only tools, and the degree to which they affect decisions is as highly varied as are the personality differences and business conduct and outlooks of the persons who render the decision of "go or no-go". The independent consultant, then, is expected to provide an additional increment of credulity and/or reliability to the "tools" which others will use in reaching a decision; the consultant is really not in a position to directly recommend a "go or no-go". PROJECT FINANCE INGREDIENTS The project finance situation has basically three ingredients: - The project; - The inherent risks attendant with project failure; - The parties. The project, to be viable for financing, will have certain essential characteristics, namely: 1. Clear title or rights to the mineral; 2. Proven definition/establishment of mineral quantity; 3. Financial viability; 4. Physical access consistent with financial viability; 5. A market for the product at a price and for the quantity consistent with financial viability; 6. Transportation/shipping from the project facility to the market at a cost consistent with financial viability; 7. Availability and demonstrated expertise of the developer of the facility; 8. Demonstrated expertise of the operator of the facility; 9. Production processes do not involve unproven new technology; 10. Availability of management personnel; 11. The property and the facilities have value (and thus can be used as collateral); 12. Government approvals/support, as required, will have been obtained; 13. The political environment is essentially friendly and stable; 14. The owner(s) of the project have the financial, strength to make equity contributions consistent with total required investment capital and project risk; 15. Backing by credit support other than that of the financier (i.e. guarantees); The inherent risks of failure are (Nevitt, 2nd Edition); 1. Completion delays with consequent delays in the generation of revenue 2. Cost overruns 3. Technical failure 4. Financial failure of contractors 5. Government interference 6. Uninsured losses 7. Increased price or shortages of raw materials, supplies 8. Technical obsolescence 9. Loss of competitive position in the market place 10. Expropriation 11. Inadequate/poor management The parties directly or indirectly integral to the project financing are: - The mineral rights owner - The developer - The operator - The equity investor

Jan 1, 1985

Mineral exploration and development can have a significant impact on the environment and local communities, in some circumstances extending well beyond the mine site. Poor environmental performance and consequent social impacts by some companies have affected the reputation of the whole industry to the extent that the principal public concern about mining is its impact on the environment. This is consistent with public attitudes about other major natural resource sectors such as forestry and commercial fishing. Traditionally the community has relied on governments to set the benchmark for acceptable environmental and social performance through establishing and revising regulations governing the mining industry. This however assumes that regulations keep pace with community expectations. It also does not take into account those circumstances where governments can have conflicting roles as both watchdog and project partner. Government regulations and industry self-regulation are not in of themselves sufficient for the minerals sector to demonstrate that it has adequately addressed environmental and social issues associated with the sector. For the minerals sector to improve its reputation it must first improve its environmental and social performance. To do this requires the sector to operate to acceptable standards of environmental and social performance and for the sector to be able to credibly communicate this to its stakeholders such as investors, non-government organisations (NGOs), customers, staff, regulators and local communities. Independent third party certification of environmental and social performance (æcertificationÆ), already operational in forest and fisheries management, is proposed as a mechanism to enable the minerals sector to achieve this. World Wide Fund for Nature (WWF) and industry partners will be collaborating in a project to ascertain the applicability of æcertificationÆ to the minerals sector. A number of economic, social and environmental benefits are identified that could accrue should mining companies be able to differentiate themselves on the basis of environmental and social performance, an attribute evident in æcertificationÆ schemes. External audiences are seeking increasing levels of information and data on environmental and social performance of mining companies, be it local communities, investors, financial institutions or NGOs. Environmental and social reporting should be a key communications device that stakeholders can rely on as a reliable, credible source of information on environmental and social performance. WWFÆs contribution to the debate about environmental and social reporting has been to develop a process to assess the quality of environmental and social reports against reporting ingredients which WWF believe are important if a report is to be an accurate reflection of the reporting entitiesÆ environmental and social performance.

Jan 1, 2002

By Grafton M. Thrasher

Discussion of the paper of GRAFTON M. THRASHER, presented at the New York meeting, February, 1916, and printed in Bulletin No. 106, October, 1915, pp. 2129 to 2138. RICHARD MOLDENKE, Watchung, N. J.-Mr. Thrasher is to be commended for developing a very interesting comparison between high- and low-carbon and silicon malleable cast irons for an equal degree of chill. His deductions are unquestionably correct, though the application to daily practice is open to serious criticism, from the standpoint of the man who receives the castings, as will be shown later on. Running over some of the points which affect the tests in question: Mr. Thrasher admits that the temperature of pouring has a serious influence on the degree of chill shown in the test plugs he made. This is a well-known fact, and I would like to add that another serious trouble comes from oxidized iron when the heats have been unduly prolonged. Such metal always shows more chilling action for a given silicon and carbon content than normally melted iron. Indeed, the test piece quoted giving the extreme of the chill line (1.07 per cent. Si and 2.47 per cent. total carbon) was such a poor heat, a ferro-silicon addition never "doctoring" up the metal sufficiently to show normal good strength. In spite of these irregularities, which would simply change the curve slightly, I take it that Mr. Thrasher's results can be accepted as reliable enough to establish the relationship of silicon and total carbon as shown. When, however, the claim is made that silicon and carbon can be substituted for each other in mixture-making (a claim which may be perfectly correct metallurgically), a very important factor is forgotten, causing the purchaser of the castings much annoyance. This is the contraction (erroneously called shrinkage) of the castings. They will no longer be true to pattern. The lower the total carbon is allowed to drop, the greater the contraction, and increasing the silicon correspondingly will not correct this trouble. No wonder that recently, in revising the Standard Specifications for Malleable Castings it was necessary to increase the variation of castings from requirements considerably over what was formerly found sufficient. The habit of running up the proportion of silicon and escaping danger from grayness of the metal by copious steel additions was evidently too tempting to manufacturers, as their molding losses were thus kept down and a very soft malleable iron resulted. The customer, however, got serious variations in his work, which was not the case when the total carbon was kept between 3.25 and 2.75, and the silicon held as low as possible without undue cracking of the hard castings.

Jan 5, 1916

By James L. Evers

Introduction There is a continuing search by government and industry for new mining methods that increase production, improve the working environment, reduce labor intensity, enhance recovery effectiveness, improve the reclamation process, streamline the flow of material, and reduce the unit cost. Hydraulic extraction and transport methods have outstanding potential in several of these areas. For example, hydraulic fragmentation produces a significant reduction in respirable dust. The inherent simplicity of hydraulic mining equipment and the resulting high reliability are recognized. Tool wear can be virtually eliminated. There is great flexibility in the size, shape, and orientation of the mineral deposit that can be mined. The cutting, gathering, and transport operation can be controlled remotely, providing more safety for workers. The threat of tool sparking and the resuiting dust or gas ignition are also eliminated. Although hydraulic mining was introduced in the US before the turn of the century, it has not gained the degree of acceptance found in other countries such as the Soviet Union, China, Germany, and Canada. The Hydraulic Mining Research program, initiated by the US Bureau of Mines in 1958, and the subsequent research by others has provided much of the basic technology required to spur the development of these methods into a viable extraction alternative. This article updates the development of hydraulic mining in the US. Particular attention is paid to monitor mining, the long-wall hydrominer, borehole mining, and the semi-autonomous mining system. Whenever the particular mining method is also being developed in other parts of the world, a brief description of the world-wide state of the art is given. Finally, allied studies designed to optimize these mining techniques are described. Hydraulic Monitor Mining Since 1958, the US Bureau of Mines (USBM), the Department of Energy (DOE), and other government agencies have funded more than a dozen programs to investigate the potential of hydraulic monitor mining. For this method, water is directed on the coal face from a monitor nozzle. Sufficient velocity is used to cause local fragmentation (Fig. 1). Coal particles are washed from the face to a trough. They are then flumed to a collection point. Oversized particles are directed through a breaker and then into the troughs. Monitor field tests were conducted in the 1960s in bituminous and anthracite coal at the following locations: • Rosylin No. 9 mine, WA (Nasiatka and Badda, 1963); • Rosylin No. 10 mine, WA (Price and Badda, 1965); • Sugar Notch mine, PA (Buch, 1964); • Thomson Creek mine, CO (Palowitch and Malinka, 1964); and • West Lebanon, PA (Fowkes and Wallace, 1968). In 1975, Ingersoll-Rand Research Inc. was awarded a two-year USBM contract to develop a continuous coal mining system using water jet fragmentation and

Jan 10, 1984

By Paul D. Tomlingson

A new sense of urgency permeates the mining industry concerning maintenance. Mining's continuous process environment demands around-the-clock maintenance support. And profitability conscious mining operations require that production targets be met on time - and economically. These goals require nothing less than an effective maintenance program. In turn, the effectiveness of the maintenance program depends on quality information: easily procured, complete, timely, accurate, and properly used. Information picture is changing Some of the fully integrated, mainframe maintenance information pro¬grams of better days remain. Their upkeep and cost of operation, though, is becoming more difficult to justify. Some operations, faced with production cutbacks a few years ago, downscaled and found they liked it. Now, during an upswing, these operations question the need for the more elaborate, administrative-heavy programs they used to operate. Package programs are not taking their place. Too often, the packages are vague and generic. Some vendors claim that if their offerings work in a hospital complex, they must work in an underground mine. That is not so. Maintenance information in the mining industry is different. The situation has changed There are now smaller, self-contained maintenance groups whose information needs are different. These include an electrical crew in a smelter, an underground mobile equipment shop, or a remote service shop between several distant operating pits. These working environments have changed the character of the information needed as well as the methods for obtaining and using it. Operations-maintenance link In coming back from a downturn, operations people realize that their ability to meet production targets hinges on reliable equipment and avoidance of downtime. They have become familiar with the need to use maintenance services effectively. They also want quality maintenance information. When coupled with the sense of urgency about maintenance, a business-like working environment emerges that has significant new differences in both work control and information. Work control impact Work control has been streamlined to improve communications. Supporting information has been streamlined as well. • Verbal orders are the rule rather than the exception to quickly bring a multi-craft crew to the flotation section or a pit crew to a disabled haulage truck. • Written work requests and work order forms are seldom used, or even needed. Rather, electronic work control logs permit operations to request work, maintenance to acknowledge it, get ready, and do it - quickly, without delay. • Routine servicing is triggered by operating hour accumulation (mobile equipment) or tons of throughput (fixed equipment). Operations is now taking the initiative in delivering mobile equip¬ment to the "bad order line," or switching to a bypass conveyor. Operations wants immediate follow-up reports on equipment condition.

Jan 1, 1989

By Horrocks KRS, Smitham JB, Ellison JF

This paper describes the development and installation of equipment for continuously measuring separating density in the dense medium cyclone circuits of the four million tpa Port Kembla B/C plant coal washeries. Monitoring equipment consisting of magnetic coils and differential pressure cells were installed in U-tubes taking the full flow of magnetite from the drain sections of the product drain and rinse screens. The monitoring equipment measures overflow magnetics concentration and overflow density continuously and has operated since 1989. From these measurements and calibration trials, the separating density of operating cyclone modules can be inferred reliably. Variographic analyses of the data show that medium density control to +/- 0.002 RD units and separation density control to +/- 0.007 RD units are achievable. Either method for measuring separation density can be used with approximately the same accuracy, although the overflow density measurement technique suffers from the need to have regular flushing of the Dp cells which complicates the signal analysis. Data from the plant shows that separation density can be controlled by regulating medium density, but the assumption of a constant offset between medium density and separation density is erroneous.

Jan 1, 1993

By Golab K, Partridge AC, Fletcher CAJ, Holtham P

Spiral concentrators are used globally in the fine coal processing industry to segregate particles, by gravitation, on the basis of density and size. Consisting of an open trough that twists vertically downwards about a central axis, a slurry mix of particles and water is fed to the top of the concentrator. Particles are then separated radially as they gravitate downward. Since their introduction to Australia in the 1940's, the generic design has evolved largely by laboratory trial-and-error investigations of different prototypes. However, this approach has proven expensive and optimal designs have not been necessarily developed. Accordingly, Computational Fluid Dynamics (CFD) analysis has been used recently as an alternative method of investigation, to assume as is envisaged, a role in the design process. To date, CFD models have progressed to simulations of turbulent fluid flow on current production spiral designs, and are continuing to be adapted for inclusion of particles at realistic feed concentrations. To be able to use the models confidently however, laboratory experiments must also be performed to validate the predictions during the development stage. This paper reports the current findings of an ongoing CFD and experimental program applied to one spiral unit. Satisfactory quantitative agreement has been achieved for the fluid and particulate flow characteristics, and although further validations are appropriate, the model already possesses significant potential for use as a reliable predictive design tool.

Jan 1, 1998

By Eric Zahl

Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health, Spokane, WA, have collaborated with three Western longwall coal mines in an ongoing effort to develop technologies that will aid in providing safe and stable working areas. The goal of the research described here is to develop a stress monitoring system that will provide immediate information to mine managers for making daily safety decisions as areas of poor ground are mined through. Initial work has focused on answering preliminary questions regarding the reliability and use of stress change patterns. Research is concentrated on monitoring horizontal stress because horizontal stress is transmitted over long distances through stiff strata, thus allowing an extended length of entry to be monitored. This paper presents an explanation of the concept, key results from field tests at two mine sites, and a proposed process for imple¬menting a monitoring system. System design layouts, instrument use, data collection and interpretation methods, and processes to present findings to mine staff are described. Additional validation and correlation with actual failure mechanisms are required before this approach can be recommended at ongoing operations. How¬ever, initial results indicate that this approach shows promise in mines prone to bumps and roof falls associated with large stress changes. In particular, analyses of measured changes in horizontal stresses appear useful.

Jan 1, 2002

Concentrator Improvements -1990-1995Back to Basics ?pilot plant versus plant opportunities identified ?understand process fundamentals & baseline -1996-2000Point ?C?Projects ?strategy to improve global competitiveness ?structure implemented to generate & drive ideas ?capital investment for life of mine asset renewal - 2001-200?Six Sigma Methodologies ?emphasis on data, measurements & analyses ?dedicated, highly trained personnel on projects 1990-1995 Improvement Phase??Philosophy??back to basics?approach?understand what each piece equipment needed to do?understand reagents, control variables?confirm operating strategies ??probe, stabilize, institutionalize??test theories, confirm with lab and plant trials?process stability (equipment reliability, controls)?enhanced operator guidelines, operator training?focus on continuous improvement?optimize existing equipment capability?stop looking for ?magic?solutions 1990-1995 Improvement Phase??Technical?finer grind, same equipment?optimize media size/shape to grinding application?balanced available ball mill power to applications?lowered cyclone feed densities where possible?improved selectivity, same equipment?balanced available cells to applications?streamlined process (eliminate process steps)?added cleaning stages where required?understanding pulp/mineral surface chemistry?lowered flotation pulp densities 1990-1995 Improvement Phase??Effort?numerous studies to understand process?liberation and mineralogical characterization?pulp and mineral surface chemistry?flotation kinetics and entrainment?extensive internal and external manpower?Brunswick, Noranda Technology Centre?CanMet, AMTEL, MinnovEx, Lakefield Research, McGill University?small capital expenditure

May 1, 2002

By Marc T. Filigenzi

Two of the major ground control safety issues confronting underground mine operations today are shaft pillar stability and the failure of rock around active mine openings. Failure of a mine shaft can lead to the entrapment of workers. Failure of rock around active underground mine openings can lead to roof falls, which in turn can result in worker injuries and fatalities. Finite-element analysis has proven to he a reliable method for predicting stresses and displacements around underground mine openings. However, this is a complex and time consuming technique and is not used as often as it could be in mine planning. The purpose of this paper is to demonstrate one technique developed at the Spokane Research Center that allows the user to create a finite-element model of a two-dimensional section of an underground mine in a relatively straightforward manner. This model is then used to calculate stresses, displacements, and safety factors around mine openings. With this information, mine planners can evaluate the stability of mine openings as well as the stability of pillars and mine shafts. This analysis will help develop mining sequences and layouts that minimize stresses in that section of the mine. This, in turn, should minimize the occurrence of shaft failure, roof falls, and other hazards associated with underground mining.

Jan 1, 1997

The prime objective of geometallurgy is to improve the profitability of mines through the use of spatial models of rock properties that have a significant impact on value. Although a key property is the grade of the component of interest, because it directly influences the revenue from saleable material, increasingly attention is being focused on other attributes. These 'non-grade' variables may have a less direct, but equally profound impact on value, either by reducing potential revenue (eg lowering recovery, deleterious elements, etc) or increasing mining or treatment costs (eg comminution, grindability, throughput, reagent use, etc). Collectively, these variables have been described as 'geometallurgical'. There are three main areas of activity required to realise the value of geometallurgy: 1. acquisition of appropriate data through sampling and measurement, 2. building spatial models of geometallurgical variables, and 3. using these models to optimise value. Each of these is built on the foundation of the preceding step. In building reliable spatial models, it is critical that the amount of error introduced to data by the sampling and measurement processes is understood and quantified, in order that the inherent variability of the component of interest can also be properly understood. Management of the quality of grade variables is now applied (with different levels of diligence and success) across nearly all sectors of the mining industry, not least because of the necessity to adhere to Codes of practice (eg JORC, 2004). The necessity for quality management and at least the broad framework of what to do in practice is reasonably understood by many relevant professionals. There are also a number of tools, including software products, statistical analyses and presentation formats, available for those managing grade data. It is also abundantly clear, that in many cases people have little understanding of why they are doing particular quality control activities, or how to sensibly interpret the results. The same is not true for many geometallurgical variables. In almost all instances the authors have seen, the magnitude of sampling and analytical/measurement error variance embedded in geometallurgical test data is untested and unknown. This is partly because until relatively recently, metallurgical data has mainly been collected for the purpose of process and mill design, with few, expensive tests carried out on 'average' samples of the orebody. Increasingly however, there is a move towards collection of much larger data sets from spatially distributed sampling, and thus a growing necessity to understand the errors inherent in both sampling and analysis of these types of variables, and how to manage them. In order to understand how the quality management practices applied to grade variables can be extended to geometallurgical variables, it is essential to understand the theoretical foundation that supports these practices. This requires an analysis of the concepts that underpin the 'principles of additivity' (Matheron, 1963), the 'theory of sampling' (Gy, 1982, Pitard, 1993), and 'statistical process control' (Shewhart, 1930). Relevant concepts are then integrated to form a foundation to develop methods to improve the quality management of geometallurgical variables. Application of this framework will significantly increase the integrity of geometallurgical data, the reliability of geometallurgical models and ultimately the value derived from implementing geometallurgy. This is an ABSTRACT ONLY no paper was prepared for this presentation.

Mar 1, 2010