Search Documents

By J. D. Rice, S. C. Pitzer, C. E. Thomas

Interpretation of pressure build-up data obtained in the conventional manner has often been difficult because of the deviation from theoretical behavior. Major causes of this deviation have been attributed to damage and afterflow, and to fluid redistribution in the wellbore which, in extreme cases, can result in a pressure hump in the early portion of the build-up curve. Theoretical investigations show that bottom-hole pressure is definitely influenced by phase redistribution in the tubing column during surface shut-in tests, and that the magnitude of the effect is sensitive to the producing gas-oil ratio and stabilized rate of flow in the well. For field experiments a wire-line tubing packer, which can be run in the tubing against a stabilized flow rate, was developed for bottom-hole shut-in tests. By use of this bottom-hole .shut-in method, pressure humps previously observed in surface shut-in tests were completely eliminated and the effects of afterflow minimized. Analog and digital computer studies have been made to obtain theoretical curves for comparison with field curves, and remarkable agreement between the results of bottom-hole shut-in tests and theoretical curves has been obtained. INTRODUCTION Pressure build-up data from shut-in wells have been used by the petroleum industry to determine the permeability of the formation, to estimate wellbore damage, to evaluate the static reservoir pressure and to speculate reservoir volume. Calculation of these factors is based on methods of analysis developed for theoretical systems whose build-up curves have a charac- teristic shape when the wells are shut-in at the sand faCe.1,2,3,5,8,10 However, field curves obtained by conventional surface shut-in methods do not always exhibit this characteristic. Such factors as stratification, rock heterogeneities and irregular reservoir geometry can cause the character of a build-up curve to deviate from that predicted by theory for a simple system. In addition, all field build-up data are affected by the methods utilized in obtaining the measurements. Conventional surface shut-in techniques allow two effects to occur which contribute directly to the manner in which pressure builds up at the sand face. The first, afterflow, has been recognized for some time and methods are available for estimating the magnitude of its effect and for correcting its influence.' The second, phase segregation in the tubing column after shut-in, has been reported only recently and appears to exert a considerable influence on the character of field build-up curves.!' In extreme cases, phase segregation can produce "pressure humps" in the early portion of the build-up curve. Such curves have been considered anomalous and have defied analysis. It is the purpose of this paper to discuss the effect of phase segregation in the tubing string during build-up and to present a bottom-hole shut-in technique for obtaining field build-up data which minimizes the influence of afterflow and eliminates phase segregation effects. It will be shown that reliable reservoir information can be calculated from build-up measurements obtained using this method, even though conventional surface shut-in tests on the same wells yield anomalous data. DISCUSSION OF PHASE REDISTRIBUTION EFFECTS Some of the effects of phase redistribution on pressure build-up curves have been described previously by Matthews and Stegemeier" who have presented evidence that phase segregation is responsible for the pres-

The Bureau of Mines, through its Minerals Availability Program (MAP), investigates the mineral supply potential of the United States and market economy countries (MEC's) for a number of minerals considered essential to the U.S. industrial base. Major activities include identification of important mines and mineral deposits, estimation of their mineral resources and production costs, and availability and sensitivity analyses. Products include data print-outs of geological and engineering information, discounted- cash-flow rate of return (DCFROR) analyses of individual mining operations, commodity availability appraisals, and analytic services to Government agencies. These products are used in assessing the mineral supply position of the United States: in setting priorities for research aimed at reducing production costs and minimizing adverse environ- mental impacts and regulatory compliance costs of mining and mineral processing operations; and in formulating and evaluating Government policies that affect minerals. Bureau MAP data and analyses have been provided to the executive and legislative branches to aid in consideration of trade, tax, and stockpile policy issues. A study of the economic potential of selected seabed mineral resources supports the regulatory responsibilities of the Department of the Interior in the U.S. Exclusive Economic Zone. Analytic studies of mineral project viability, industry competitiveness, and import dependencies were also undertaken for, or in cooperation with, U.S. and foreign government agencies, industry and trade organizations, and international lending institutions.

Jan 1, 1987

By R. C. Adams

This report describes the feasibility of mining the oil-shale deposits of the Piceance Creek basin in Colorado by an integrated open pit system. The study is based upon a comprehensive analysis of pertinent environmental, economic, and engineering factors. Ten mining cases are investigated, and the mine design and cost estimates for each case are presented in this report. Nine of the cases represent three cutoff grades, defining oil shale ore as equal to and above 15 gallons per ton (gpt), 20 gpt, and 25 gpt, at three ore production levels of 500,000 tons per day (TPD), 1,250,000 TPD, and 2,500,000 TPD. The tenth case is an alternate design of the 500,000 TPD production rate at the above 15 gpt cutoff grade. The report consists of Volume I, a technical and cost comparison of the ten cases; Volume II-Part I, a detailed explanation of the estimating methods used; and Volume II-Part 2, a more detailed discussion of the technical and cost features of the ten cases than is presented in Volume I.

Jan 1, 1976

By Xinquan Zhou, Rudolf E. Greuer

MFIRE, written in Fortran 77, is a computer program for ventilation state simulation in the steady state or transient state condition. It can be applied for the calculation of normal ventilation system planning or the analysis of the dynamic state variation in a ventilation system under thermal or mechanical disturbance. The state simulator MFIRE is a useful tool for mine fire fighting. In the case of a mine fire, mine ventilation engineers want to get some help to obtain more information, such as what is happening in the underground mine and how to control the mine fire, for correct decision making. By use of program MF'IRE, forecasts can be made on the variation of airflow, temperature, and contaminant distribution in a ventilation system during a mine fire. The paths which the contaminant takes at each time interval can be traced. The program MFIRE can be of assistance in the preplanning of escape routes. It can also be helpful during a mine fire emergency and mine recovery operation. Besides of offering the information of state simulation during a mine fire, MFIRE can be applied for state control by pretesting the suitability of the selected state control measures. It is to simulate the effects of the state control measures on the airflow distribution of a dynamic ventilation system. The testing result can be used for fire fighting in a similar real case of a mine fire. By employing empirical methods or a qualitative analysis like Budryk approach, ventilation engineers can choose different combinations of locations and sizes of control devices as samples of state control for an underground mine fire. Program MFIRE can simulate the different combination samples, that consist of a certain mine fue, the corresponding different control measures, and obtain the control effects. After the different control results are compared, the state control measure, which creates the best effect among the different state control measures, will be chosen for that fire case. When a mine fire, which is similar to one of the pretested cases, breaks out, the corresponding choice of the state control measure is applied to the ventilation system. It means that the simulator MFIRE has the function of indirect state control [10]. To achieve the above two functions, state simulation and state control, the mine ventilation system condition, sometimes, should be changed in a wide range to meet the requirement of the fire fighting. These wide system condition changes, such as adding operating fans, stopping or reversing fans, changing fan characteristics, adding regulators and making airflow shortcuts are represented in the time table of the input data set When the data files are changed in a wide range, however, an iteration divergence and some other computing errors in the distribution of airflow, temperature, and contaminant may occur. More serious logical programming and flexible selection on the algorithms are wanted to meet the request of the different data sets, to achieve correct state distribution simulation and improve the iteration convergence. To enhance the reliability and common suitability of program MFIRE, it is necessary to make investigation, analysis, and modification for the formal versions of MFIRE. The version 1.29, permitting dry .calculation, and versions 2.01/v2.0, permitting dry and humidity calculation, are widely applied

By Wojciech Klecan

Cobb County, located on the northwest side of Atlanta, GA, is continually growing and, like many other metropolitan areas, it needs to increase the capacity of its waste water system to meet future demand. The Cobb County Water System (CCWS) is the responsible agency for water distribution, waste water collection and treatment in most areas of the county. CCWS, one of the most progressive agencies in the metro-Atlanta area, is addressing its future waste water capacity needs in the southern part of the county with the construction of the South Cobb Tunnel and Pump Station. This project consists of an 8.8-km- (5.5-mile-) long, 8.2-m- (27-ft-) diameter, tunnel boring machine (TBM) excavated waste water storage and conveyance tunnel; six tangential vortex-flow intakes ranging from 1,533 to 5,700 L/s (35 to 130 mgd) peak flow capacity, two construction shafts, six 1.8-m (6-ft) finished diameter connecting tunnels ranging in length from 6 to 975 m (20 to 3,200 ft) and a 5,700-L/s (130-mgd) wet/dry pit pump station. The pump station will have a semi-circular wet well with a dividing wall that extends almost to the top of the shaft and a spilt dry well for reliable operation. Roller gates will control the flow to the wet well from the tunnel. The pump station will have six 1,420 L/s (32.5 mgd) pumps and two sets of stair wells and elevators. With a finished diameter of 32 m (104 ft) and a depth of 62 m (204 ft), this is the largest pump station shaft constructed so far in Georgia for the dewatering of a waste water tunnel. The pump station shaft was also the highlight of the well attended and successful 2009 Shaft Design and Construction Short Course held in Atlanta, Sept. 10-11. The two-day course was sponsored by the Underground Construction Association of SME and Pennsylvania State University and concluded with a field trip to the pump station shaft. The tunnel starts south of the city of Austell and finishes at the South Cobb Water Reclamation Facility (WRF), located on the banks of the [ ] Chattahoochee River just north of Interstate 20 (Fig. 1). The South Cobb Tunnel will run 30 to 137 m (100 to 450 ft) below the surface, with an average depth of about 91 m (300 ft), through metamorphic rocks (Fig 2). The construction contract was awarded to Shea-Traylor JV with the lowest bid price of $305 million and notice-to-proceed was given on July 14, 2008. Jordan Jones & Goulding, Inc. (JJG) is the project designer and performed the geotechnical investigations. Parsons/Jacobs Associates is the construction manager. The South Cobb Tunnel is CCWS?s second deep hard rock tunnel. The 15.3-km- (9.5-mile-) long, 5.5-m- (18-ft-) diameter TBM excavated the Chattahoochee Tunnel was the first deep tunnel to be construced in Cobb County. Construction began in 2000 and the project was completed four years later. It is located about 16 km (10 miles) northeast of the South Cobb Tunnel in similar geology. It was designed by JJG to meet east Cobb?s long-term waste water capacity needs and provide flow equalization to the R.L. Sutton WRF. The Chattahoochee Tunnel was named ?Outstanding Civil Engineering Project of the Year? by the Georgia Sec-tion of the American Society of Civil Engineers in 2006.

Jan 1, 2009

From the massive equipment that moves the earth, to the parts that keep the equipment moving, it was all on display for more than 35,000 people who at-tended MinExpo 2008 at the Las Vegas Convention Center Sept. 22-24. In the largest show in the illustrious history of MinExpo, the success of the recent commodity boom was reflected in the more than 55,700 hm2 (600,000 sq ft) of floor space that was jam-packed with nearly 1,300 vendors. Among them, the makers of the industry?s largest machines, displaying their latest and greatest trucks, shovels, excavators, drills and other mining equipment. During the nearly decade-long commodities boom, equipment makers have worked hard to keep up with demand while also investing heavily in research and development. The beneficiaries of this R&D is the end user who saw first-hand at MinExpo 2008 the many advances that have already been made in safety, comfort and productivity from all the manufacturers. R&D has also helped spark more talk of automation, which is being used already at some of the world?s largest mines. Caterpillar and Komatsu have worked with the technology in surface mining and Bucyrus and Sandvik are among the industry leaders applying the science of automation to underground mines. Technology has in-creased greatly since the idea of moving massive equipment remotely was first knocked around and the idea of entire fleets operating around the clock seems to be getting closer to reality. But, until that happens, MinExpo attendees were treated to a show that featured some of the most impressive current machines the industry has to offer. In the largest booth space of the convention, Caterpillar (www.cat.com) displayed the culmination of an ambitious $280-million dollar investment, with the introduction of its new mining fleet of four new trucks. The F-series was un-veiled with common features in safety, cabs, engines, frames and bodies and Tier 2 compliant engines. The F series also features a return to the electric drive option. ?When our customers asked us for improvements to our mining trucks, we responded by making a record investment in every single truck in our line, as well as the increased capacity to produce more of them,? said Cater-pillar group president Stu Levenick. ?New technologies have allowed us to make trucks more reliable, easier to maintain and more friendly to the operator and to the environment.? The 793-series is in the 218- to 227-t (240- to 250-st) class that will be available in both mechanical (793F) and electric (793F ac) versions. The electric drive-only 313- t (345-st) 795F was also introduced, while the flagship 797B truck is in the process of being replaced by the new 797F mechanical drive, maintaining its 345- to 363-t (380- to 400-st) target payload. Completing Caterpillar?s new mining truck line will be new versions of the 785 and 789 mechanical drive trucks. The next generation of trucks will be phased into production during the next two years, with the Cat ac drive models expected to go into production in late 2010. The $280-million in-vestment is Caterpillar?s largest commitment ever to the mining industry

Jan 1, 2008

This dictionary is published by the Bureau of Mines as a contribution to the mining and mineral literature in the belief that it will fill a recognized need. Several attempts have been made over the years to revise Albert Fay's Glossary of the Mining and Mineral Industry which first appeared in December of 1918. Frank L. Hess of the Bureau of Mines worked on a revision, but his untimely death prevented its completion. Subsequently, the writer was employed to compile and edit this dictionary in cooperation with the technical staff of the Bureau of Mines. Fay's glossary contained about 18,000 terms with 27,000 definitions; the present compilation contains about 55,000 terms with approximately 150,000 definitions. These terms are of both a technical and local nature, and they apply to metal mining, coal mining, quarrying, geology, metallurgy, ceramics and clays, glassmaking, minerals and mineralogy, and general terminology. Petroleum, natural gas, and legal mining terminology, unless of a general nature, has been excluded, as has been foreign terminology where there is an English equivalent. Several thousand Spanish-American mining terms that appeared in Fay's compilation have been removed to make way for the thousands of new English terms that have evolved over the years. Those Spanish-American and Mexican terms still used in the Southwestern United States have been retained.

Jan 1, 1968

By Tom Dettweiler, Robina Sharpe, Wright. Michael

The International Seabed Authority and a number of countries have or are in the process of developing environmental impact assessment guidelines and legislation for seafloor mineral development. The formal decision to grant a project an environmental permit is based on an environmental and social impact assessment (ESIA), culminating in an environmental impact statement (EIS). The EIS needs to be supported by sufficient data upon which an assessment of impacts can be made and mitigation measures developed. Given the remote locations of many seafloor prospects, collection of sufficient environmental data to inform an EIS is often a difficult, expensive and lengthy process.

Sep 1, 2014

"M bed, Matanuska valley, Alaska, coal carbonizingproperties B 510M spectral lines, low-energy, study RI 5538Mab shaft, Leadvile district, Colo., investigation RI .1518Maberry process, for aluminum chloride TP 321"

Jan 1, 1960

By G. W. Josephson

WHILE methods of utilizing blast-furnace slag have been developing, a great deal of literature on the subject has accumulated, but no comprehensive summary of information that would be helpful to engineers, contractors, architects, chemists, and others in under-standing and more successfully using this byproduct of the iron and steel industry has been published in the English language. The National Slag Association recognized the need for such a publication, and the Problems Committee of the Association under-took in 1943 to accumulate the necessary material. Over a period of several years this committee compiled pertinent information in manuscript form, and in 1948 the Bureau of Mines and the National Slag Association made an agreement whereby the Bureau was to prepare the data for publication as a cooperative bulletin of the Bureau of Mines and the National Slag Association.

Jan 1, 1949

By Charles Fried

The Coal Mine Health and Safety Act passed by Congress in 1969, called for research to alleviate the occupational stresses and hazards of coal miners. Spurred by a series of recent mine disasters the Congress directed the Bureau of Mines to increase its attention to the welfare of miners and to develop better working conditions and personal equipment for use in the mines. As one of the early steps in carrying out the provisions of the Act, the Bureau of Mines commissioned the Behavioral Sciences Group at the National Bureau of Standards to conduct a survey of the state of the art in ergonomics (human factors) as it has been applied to mining.

Jan 1, 1972

By D. Marcotte

The Rock Quality Designation (RQD) is a standard scalar measure of rock quality used in common rock mass classification systems (e.g. RMR, Q system). RQD is measured along diamond drill holes. RQD interpolation between holes is nontrivial. Despite the inherent limitations of drill hole data and the local complexities of structural geology, it is often the only information available for mining and major civil engineering projects. Therefore, maximizing the usefulness of this data is warranted. We derive a correction for directional effects that help reduce the bias and improve the accuracy of the estimations. The correction is derived with the aid of numerous simulations. It relies on simple information, the angle between the joint normals and the borehole axis (JO). A reference direction is identified as the borehole direction with smallest JO. A multiple linear regression model based on JO statistics in the various boreholes defines the correction model. The corrected RQD values are then interpolated. It is shown the method enables reducing the bias on RQD estimation by 50% and improves the accuracy of the estimates by 30%. The corrected RQD values show stronger spatial continuity than the raw values. The benefits of estimating the RQD indirectly by using joint frequency measures are also assessed.

May 1, 2003

By L. B. Pankratz

Thermodynamic data on the elements and oxides were reviewed, evaluated, and compiled at the Bureau of Mines Albany Research Center. Values for Cp°, S°, H° - H°298, - (G° - H°298)/T, ?HP, ?Gf°, and log K are given in tabular form. Cp°, H° - H°298, ?Hf°, and ?Gf° are also expressed algebraically. Examples of calculations using these data are given.

Jan 1, 1982

By R. H. Winn

A method for the selection of the most suitable corrosion inhibitor for a particular system is given. The method involves the evaluation of surface passivity by means of copper ion displacement after the metal surface has been subjected to the corrosive atmosphere. The application of the method to the selection of suitable inhibitors for use in producing wells is described. Correlation with recognized laboratory tests has beet1 found to be good within the limitations of the test. The use of the test to evaluate inhibitor persistencc is described. INTRODUCTION Corrosion as it is associated with the industry shows wide variations in its qualitative as well as its quantitative aspects. This complicates the work of the corrosion engineer. In the past few years the efforts of the corrosion engineer have been further taxed by the large numbers of products being marketed as corrosion inhibitors by various manufacturers. These products are submitted to him together with a limited amount of data to support their use as inhibitors. The data are usually authentic and reliable yet all too often when these products are applied to an actual corrosive system the results are disappointing due to the ineffectiveness of the inhibitor and the corrosive system. The corrosion engineer must select a comparatively limited number of inhibitors for field trial from the large number available. The selection is usually made on the basis of a standardized laboratory test such as that adopted by the National Association of Corrosion Engineers or by field experience in an area; however, testing of this type is discouraging on large numbers of compounds, particularly in view of the specificity of environment. It has been an object of this work to devise a method which will allow the corrosion engineer to select the best inhibitor for a specific environment under field conditions. The test would of necessity be rapid and inexpensive. It would preferably eliminate the need for expensive and delicate instruments. STATEMENT OF THEORY The test as developed makes use of the fact that metal ions will be displaced from solution by metals having a more positive electrode potential. Thus, if an active iron surface is exposed to a solution of a copper salt, free copper will plate spontaneously on the iron surface as it is displaced from the salt solution by iron ions. If the iron surface is passified, as by coating with an insulating-type organic corrosion inhibitor, it is no longer capable of displacing the copper ions due to its own limited ionization. The result will be a change in the amount of copper plated upon exposure to a neutral copper salt solution. In practice it has been found possible to measure the magnitude of the alteration of the cell potential by determining the copper deposited on a standard iron surface under controlled conditions. This means that, as the film builds up, the resulting shift in the electrode potential tends to cause the iron surface to act more like a noble metal, resulting in a reduction in the cell potential to a point that copper will no longer plate spontaneously. Obviously, the salts of other metals such as silver, gold or platinum might be used for this operation; however, copper was selected because of the color difference of the plate, the comparatively low cost of copper salts and the ease of evaluation of the plated copper. Furthermore, its high cell potential provides a substantial driving energy. The determination of the copper is readily done colorimetrically by dissolving it in 5 per cent ammonium hydroxide solution containing 2 per cent potassium per-sulfate. The blue color of the copper ammonic complex ion so developed may be compared with standards prepared by dissolving known quantities of copper powder in the same reagent. In routine screening it is seldom desirable to determine the amount of copper plated. It is usually more important to determine the concentration of inhibitor required to prevent the plating of copper.

By A. J. Kraemer

The properties of crude petroleum continue to interest the Bureau of Mines and constitute an important phase of its major studies on the mineral resources of the United States. The Bureau's interest in the subject has been intensified by frequent requests for information on the characteristics of crude petroleum from various producing fields. Since its inception the Bureau of Mines has collected and analyzed samples of typical oils and at present has surveyed and classified crude petroleums from nearly all the known oil fields of the Western Hemisphere. Results of these surveys have been presented in various Bureau of Mines publications. (See bibliography, appendix A, p. 145.) The nature and comparative value of crude oils from various countries and the extent to which these oils may be considered potential competitors for markets are of manifest importance to the petroleum industry in all lands, largely because all crude oils, wherever produced, are either actual or potential competitors for a market with all other crude oils. The numerous discussions of foreign production of oil that have appeared in the technical press in the past indicate the great interest of the United States in this subject.

Jan 1, 1937

By Ned H. Snyder

In recent years the Government and other large consumers of coal have appreciated more and more the desirability of definitely determining by chemical analysis and test the character and quality of the coal they purchase. Higher prices for coal point forcibly to the need of giving more study to engine room and boiler room efficiencies and economies; this implies an intimate knowledge of the character and quality of the fuel used. Analyses and tests of delivered coal furnish data whereby power plant results can be comprehensively studied and a continuous check maintained on the coal and on the conditions of plant operation. Under authority of acts of Congress making appropriations for technologic investigation of fuels and the analyzing and testing of fuels belonging to or for the use of the United States Government, a laboratory is maintained at the Pittsburgh station of the Bureau of Mines, where samples representing deliveries of coal purchased for Government use are analyzed and tested.

Jan 1, 1923

By G. S. Scott

Mine fires have occurred since the mining of coal was begun, and they are still occurring. The resulting economic waste may become considerable (219),3 especially if a fire is allowed to assume major proportions or to get beyond control temporarily. It is important, therefore, to act promptly whenever a fire is suspected and to have every action count. To do this effectively, it is necessary to know at the earliest possible moment and thereafter what is happening in a remote or inaccessible area. It is equally important to know before¬hand what may be expected as a result of any proposed combative measure. The logical method of combatting a fire demands the cooperation of both mining engineer and chemist. They should decide the course of action to be taken, drawing upon the mining engineer's intimate knowledge of the physical structure of the fire area, the cost and time required for proposed operations, and the probable efficiency with which they could be carried out, and upon the chemist's knowledge of the results to be expected therefrom.

Jan 1, 1944

By S. H. Ash

The Pennsylvania anthracite region is composed of four fields, namely, the Northern, Eastern Middle, Western Middle, and Southern. It is in the eastern part of Pennsylvania and is shown on figure 1. The anthracite industry is confronted with a crucial problem of inundation by water impounded in underground pools in many mines and by infiltration of water from streams and pools on the surface (3). The deposits of anthracite in the United States are limited virtually to Pennsylvania, and the difficulties of this industry have been commonly considered as a State problem rather than a national one (1, 4, 6, 7). Anthracite was discovered in Pennsylvania in 1762, and the first mining company was formed in 1793. It was not until 1812 that anthracite began to receive recognition in the Philadelphia market as a domestic fuel, and by 1838 the annual production was nearly 1 million net tons. Since anthracite mining began, mine water has become progressively more difficult and costly to handle because of the extraction of anthracite both underground and along the outcrops of the beds, until at the present time mine drainage is a major anthracite-mining problem. Mine water is handled at the anthracite mines as follows: (a) by pumping, (b) by drainage tunnels, (c) by combination of pumping and drainage tunnels, and (d) by water hoists (hoisting water by means of large buckets) (4, 5,6, 7). This paper covers removal of the water from mines by means of pumping plants. Pumping is indispensable in the production of anthracite (5). The cost of pumping mine water has increased progressively since anthracite mining began. Some collieries have been forced to discontinue mining because of the high cost of pumping.

Jan 1, 1950

By Philip C. Tully

This bibliography contains 2,072 citations to technical and scientific literature about helium and alpha-particles abstracted by 12 abstract service publications during 1962. Citations are listed by 16 major subject classifications with several subclassifications to minimize areas of literature search. Automatic data processing was used to reduce the time and labor required to compile the bibliography.

Jan 1, 1969

By E. H. Burroughs

This bulletin is the sixth in the series of petroleum bibliographies published by the Bureau of Mines, Bulletins 149, 165, 180, 189, and 216 being compilations for the years 1915, 1916, 1917, 1918, and 1919- 1920, respectively. In this bulletin the same general plan has been followed in arranging the references, but one or two additions have been made in the classification.

Jan 1, 1921