Search Documents

By I. Nolet

Matte tapping is one of the most critical operations of a matte smelter. Every smelter has developed particular matte tapping practices and tap-hole repair strategies that are often based on the experience of the smelter personnel. As a result, very little information has been published on these critical topics. This paper aims at providing the information gathered from a survey conducted in the PGM and Ni industries on matte tapping practices and tap-hole maintenance strategies for different PGM-Ni matte smelting operations.

Jan 1, 2014

By C. Haycocks

The problems caused by interaction in multi-horizon mining are world wide and are not limited to the coal industry. These problems will continue to increase as mining of new seams multiplies and replaces production from mined out horizons. Interaction problems are particularly evident in the Appalachian coal fields which contain many mineable, contiguously placed coal seams. Selection of the mining sequence of these seams, historically and currently, is based primarily on considerations of seam ownership, availability, and economics. Experience has shown, however, that mining any seam can seriously affect subsequent operations in coal seams both above and below the one being mined. This interaction effect is often detrimental to the recovery cost and safety of mining the subsequent seams. Designing to avoid or minimize interaction effects represents a major challenge to the modern coal mining industry and therefore is the focus of this research. In an effort to evaluate past interaction effects and provide guidelines for future mine design, interactive ground control problems were categorized into four areas. These are pillar load transfer, massive interseam shearing, subsidence and pressure arching effects. To facilitate research, each of these areas was studied separately although in reality these subdivisions are arbitrary and have considerable overlap.

Jan 1, 1983

By J A Evans

A well-maintained and low cost mining operation today requires the use of condition monitoring techniques. At ERA - Ranger Mine oil analysis, vibration monitoring, infra-red themtography, and performance analysis have been successfully applied over the last four years to lower operating and maintenance costs. All condition monitoring is scheduled through a comprehensive in-house developed maintenance management system known as the Engineering Information System (EIS). (EIS) is used extensively at Ranger to ensure consistent frequency and recording .of all condition monitoring data. This paper provides an insight into the benefits of condition monitoring and explores the future direction for condition monitoring techniques at Ranger.

Jan 1, 1994

New Trade Status for Mainland China--On January 24, the Congress approved a most-favored-nation trade status with Mainland China for both imports and exports. A Presidential Proclamation had been issued earlier in anticipation of the Congressional action. Import duties on such commodities as tungsten, mercury, and antimony are automatically decreased. Defense Production Act Extended--The Defense Production Act of 1950 was extended 60 days to March 28, 1980. The provision for the usual 2-year extension of the Act is reportedly included in an omnibus energy bill that is tied up in committee. The Act under Title III provides for the expansion of productive capacity and supply and, more specifically, it gives priority to defense contracting where defense and non-defense interests conflict

Jan 1, 1980

By A. Golabchi

Building Information Modeling (BIM) is an increasingly popular method for generating and managing facility information during the life cycle of a building, ranging from facility conceptualization, through design, construction and its operational life. Organizations involved in Facility Management (FM) have the opportunity to use BIM as a knowledge repository to document evolving facility information and to support decisions made by the facility managers during the operational life of a facility. This paper demonstrates the potential of using BIM to develop algorithms that automate decision making for FM applications. The potential of utilizing BIM as an analysis tool is demonstrated through the scenario of HVAC (Heating, Ventilation, and Air Conditioning) system failure in an operating facility. In case of a typical HVAC malfunction today, facility occupants record complaints in a ticketing database maintained by the FM organization. Upon receiving notification of HVAC system failure, facility inspectors visit the location to confirm the reported failure. Upon confirmation, facility managers review building plans and specifications to develop a detailed plan of action to repair any HVAC components suspected of damage. Based on the plan of action, inspectors visit the facility to inspect and, in case of damage, repair the appropriate HVAC system components. These FM practices ? as currently implemented across the industry ? are labor intensive, time consuming, and often rely on unreliable and outdated information. To address these shortcomings, the authors propose an alternative methodology of HVAC fault detection in operational buildings. The authors implement an algorithm that leverages complaint ticket data and automates BIM to determine potentially damaged HVAC system components. Based on the list of HVAC components suspected of damage, the algorithm develops a plan of action for the facility inspectors. Finally, the authors discuss the advantages of the proposed method as well as the challenges of implementing automated BIM-enabled decision making processes in the FM industry.

Aug 1, 2013

By Welby G. Courtney

This publication reviews recent U.S. Bureau of Mines studies of frictional ignition of a methane-air environment by coal mining bits cutting into sandstone and the effectiveness of remedial techniques to reduce the likelihood of frictional ignition. Frictional ignition with a mining bit always involves a worn bit having a wear flat on the tip of the bit. The worn bit forms hot spots on the surface of the sandstone because of frictional abrasion. The hot spots then can ignite the methane-air environment. A small wear flat forms a small hot spot, which does not give ignition, while a large wear flat forms a large hot spot, which gives ignition. The likelihood of frictional ignition can be somewhat reduced by using a mushroom-shaped tungsten-carbide bit tip on the mining bit and by increasing the bit clearance angle; it can be significantly reduced by using a water spray nozzle in back of each bit, which is carefully oriented to direct the water spray onto the sandstone surface directly behind the bit and thereby cool the hot spots formed by the worn bit. A bit replacement schedule must be used to avoid the formation of a dangerously worn bit.

Jan 1, 1990

By Miguel Reyes, Chenming Zhou, MATTHEW GIRMAN

Electromagnetic energy emitted from electronic devices has been known to interfere with other electronic systems, hindering their ability to function properly. Mines have many electronic devices critical to the health and safety of mine workers that could be negatively affected by electromagnetic interference (EMI). To ensure that devices are electromagnetically compatible, tests must first be conducted to measure emissions and check for immunity. There are many standards available across multiple industries that prescribe emission limits and test methods for electronic devices. Due to the unique environment of an underground mine, it may not be enough to simply adopt a standard from another industry to mining. A literature review has been conducted, and an overview of EMI standards in other industries will be provided in this paper. Also, an example of how a standard can be applied to mining equipment is presented. Finally, recommendations on standards which could potentially be applied to mining will also be included. This work will inform the mining industry of EMI standards in other industries so that mine workers and technology manufacturers have guidance of the steps that can be taken to investigate and reduce the impact of electromagnetic interference and potentially work toward electromagnetic compatibility. The findings and research involved in this effort can also be used to explore the need to develop mining-specific EMI recommendations and standards.

Nov 25, 2021

By K. Luxbacher, D. T. Hristopulos, S. Schafrik, J. Diaz, Z. Agioutantis

Big data is generated from both surface and underground mining operations. Such data contain a wealth of information concerning safety and health in the workplace and production parameters. This paper will discuss the progress towards developing an accurate forecasting model for methane gas concentration based on the analysis of data collected from Atmospheric Monitoring Systems in underground coal mines employing time series models. Several procedures need to be applied to raw data, such as data cleaning and filtering for outlier removal, data homogenization and segmentation, and exploratory statistical analysis. The data analyzed were retrieved from two coal operations in the Eastern US. A negative correlation between barometric pressure and methane gas concentration was established, at least for certain data segments. Such correlations raise the possibility that barometric pressure data can predict variations of gas concentration in the mine. The datasets will be further investigated to establish the robustness of barometric pressure and gas concentration correlation and explore the dependence of gas concentration on other factors related to mine design and operations

Mar 2, 2022

By Alvin Kaufman

Following the gold discoveries of the late 1800's much was written regarding the vast mineral resources of Alaska, and much interest was aroused, and yet over the years little has been done to exploit those resources. Between 1906 and 1935 the Kennecott copper mines of the Copper River region were the keystone of the mineral economy (fig, 1). After the depletion of the Kennecott ore reserves and aided by the statutory rise in the price of gold, the yellow metal became the major mineral commodity. In recent years it has shared the honors with coal and sand and gravel. Although this trend should indicate the development of a stable, diversified mineral industry, yet the trend of production is downward. This report results from a study by the Federal Bureau of Mines to delineate the problems and to forecast the growth of the mineral industries in Alaska. The need for such a blueprint for the future was enhanced by the population explosion in the United States and the consequent eventual need for additional living space, as well as the current interest in new areas, and the necessity to develop reserves of strategic minerals.

Jan 1, 1961

By H. P. Cole

Methods for increasing compliance to medical and health regimens were reviewed along with similar research in industrial and mine safety. Principles abstracted from both areas suggest that compliance with health and safety practices is improved when: (1) Workers are cooperatively involved with management in setting safety goals and planning for their achievement, (2) the program has the support of workers, supervisors, and management, (3) specific tasks responsible for injuries are targeted, (4) company organizational policy, educational, and behavioral programs work together toward the same goals, (5) workers and supervisors are frequently informed about their degree of correct task performance, and (6) programs are monitored by the frequency of correct performance of targeted tasks, (the means to lowered accident rates) rather than by lowered accident and injury rates themselves (the goals for safety programs.) Safety programs that incorporate these principles increase persons' adherence to specified health and safety practices and subsequently decrease injury rates. It is recommended that: (1) a group of experts be convened to study the application of these principles to coal mine safety programs, and (2) a short course for safety trainers be developed to demonstrate how these principles can be used to strengthen existing mine safety programs.

Jan 1, 1985

By I. L. Sills

Introduction So many minerals and mineral products are used in the glass industry that it would require an unduly long paper to deal adequately with all of them. Only those that go to make up the batch for the more common types of glass will be discussed here, and even with these only, the list is a lengthy one. It is true that for the body of the glass comparatively few materials are required-as silica sand, soda-ash, lime, and feldspar. The others are used mainly to colour or decolorize the glass, or to give it some other desired characteristic, such as high lustre, greater physical strength, or opalescence; but, although they may be present in very small quantities, they are just as in-dispensable to the glass industry as are the main constituents of the batch. Sand Sand is essentially quartz, the dioxide of silicon, Si02. Most glass contains from 71J to 75 per cent silica. Sand for use in the glass industry, or 'glass sand', is obtained both from deposits of unconsolidated material, commonly referred to as 'sand', and from solid rock-sandstone, quartz, or quartzite. For the manufacture of glass, the material must possess a high degree of purity, as noted below, so that, although sand is widespread in most parts of the world, and sandstone, quartz, and quartzite are not at all uncommon, it is only in certain places that suitable deposits are found. At the present time, most of the glass sand used in Canada is imported from France, Belgium, and the United States. The French material, from Fontainebleau, near Paris, is known the world over as a very high quality glass sand. That from Belgium is nearly as good and is lower is price.

Jan 1, 1934

By W. R. Reed, G. W. Luxbacher

Mine worker exposure to respirable coal dust and silica dust can result in coal workers’ pneumoconiosis and silicosis which are occupational respiratory diseases that have no cure and are ultimately fatal. In 2021 the Mine Safety and Health Administration reported just over 11,000 operating metal/nonmetal mines with the potential for silica dust exposure for just under 200,000 miners. The National Institute for Occupational Safety and Health (NIOSH) conducts respirable coal and silica dust research associated with mining through its Office of Mine Safety and Health Research. NIOSH respirable coal and silica dust research began under the U.S. Bureau of Mines (USBM), which initially examined silica dust, progressing to include coal dust, with a stronger focus after 1969 with the passage of the Federal Coal Mine Health and Safety Act. A review of extramural research to develop real-time respirable silica dust monitor is presented along with a brief history of silica dust regulation.

Feb 1, 2024

By H. A. Doerner

"The following report is submitted, in compliance with the request made by the Honorable W. H. Sproule, Chairman of the Committee on Mines and Mining, to the Director of the United States Bureau of Mines, that the bureau investigate the most modern processes for the production of radium from its ores. A thorough search of technical publications and patent office files was made. Outstanding authorities on the subject as well as persons claiming novel or secret methods were interviewed.Unlike most other elements, it is not possible for radium to occur naturally in a pure or concentrated form. This is because radium is one of a series of unstable elements which, by a constant, spontaneous, atomic disintegration, change from one element to the next in the series. Uranium is the ""grandparent"" of radium. The rates at which radium atoms are ""born"" and ""die"" are so related that only one part of radium can exist in equilibrium with three million parts of uranium. Consequently radium is only found associated with uranium minerals, and the ratio of radium to uranium is never more than one to three million. Since uranium is a rather rare element, the scarcity of radium is almost beyond comprehension. Nevertheless minute traces of radium can be detected in nearly all rocks.The carnotite ores of Colorado and Utah were the chief source of radium for many years.In the fall of 1922 news of the very rich deposits of radium ore discovered in the Belgian Congo caused most complete cessation of domestic production. The Congo ore contains pitchblende and a number of alteration products, including the new minerals bequerelite, curite, krasolite, stasite, and dewindite. Reports indicate that a considerable amount of ore containing over 50 per cent uranium oxide has been produced. It seemed certain that radium could be extracted from the Conga ore at a much lower cost than from the relatively low-grade carnotite; and in order to preserve their elaborate marketing organizations, the larger American producers made agreements with the Belgian syndicate to market the foreign product in this country. The retail price of radium has been held at $70 per milligram, but large orders are filled as low as $50. Extraction of radium from carnotite by the usual methods does not appear to be profitable at that price with one exception, all American firms ceased production after their accumulated stocks of ore had been treated. The United States Radium Co., which continued to treat carnotite for several years, finally shut down its plant."

Dec 1, 1930

By J. Pontt

Gearless mill drives (GMD) offer high performance for torque and speed control for grinding mills and have been applied successfully in modern concentrators for wet grinding with mill diameters from 34 to 40-feet. It is considered a mature technology. However, recently, some large GMD?s have presented unexpected failures in stator and rotor subsystems. The phenomena involved in such failures has shown a complex nature and surprised users and manufacturers. The manifestation of such failures has been observed as mechanical damages to certain components of ring motors. This paper presents a discussion on the electromagnetic forces that can generate stresses in the electrical ring motor that can produce failures and outages. Guidelines for further research and contributions to improved reliability of GMD?s are proposed.

Jan 1, 2012

Who's Who in Mineral Engineering - The 1979 Directory of the Society of Mining Engineers of AIME

Jan 7, 1979

By Aurel Goodwin

I chose the title "Let's Clear the Air" for this afternoon's presentation because it has two meanings, the literal and the figurative. Most of you know what MSHA is. Most of you know what MSHA does. And, for the most part, most of you know why. What I hope to accomplish today is to "clear the air" around our health standards, to clarify for you how MSHA views its congressional mandate under Title I Section 101(a)(6), (7), and (9) of the Mine Safety and Health Act. Asbestos, silica, radiation, noise, welding fumes, carbon monoxide, lead, hydrogen sulfide, nitrogen dioxide - the list of physical and chemical hazards encountered in the metal and nonmetal mining industry is as diversified as the industry itself, possibly even more so. In addition, miners are often exposed to several of these health hazards simultaneously.

Jan 1, 1980

By Nishit Patel

Development work on the use of plasma torches in blast furnace ironmaking was completed in the 1980s. The technology developers planned to reduce blast furnace coke consumption using electrical energy and large scale coal injection through the tuyeres. Since this time, Westinghouse Plasma Corporation has improved torch reliability with industrial experience in solid-waste-to-energy facilities, as well as metallurgical applications. As coke makes up one-third of the hot metal cost, savings efforts frequently seek to lower coke consumption by increasing process efficiency or replacing coke with cheaper fuels. Alter NRG and Hatch assessed the merits of using plasma torch technology to superheat the hot blast. Coke rate savings, electrical purchase requirements, and a financial analysis to implement the torches are presented.

Aug 17, 2017

By Henry F. Hebley

THE solid fuel industry, especially that branch represented by bituminous coal, is gradually becoming aware of its ? paramount importance in a world where there is an ever increasing demand for the products of a mechanical age. In practically every process of manufacture, the necessity for energy in some form is being multiplied. Some of that prime energy is derived from water power-hydro-electric schemes, flood control schemes, etc. - but often the electrical energy thus developed is generated at great distances from the load centres, requiring long transmission lines with consequent transformer and transmission losses. A few plants have harnessed the tidal power of the seas and one has harnessed the energy of the wind in a modern manner. All of these schemes are dependent on certain natural geographical, hydrographical, and physical advantages of terrain, as well as an adequate area of consumption of the energy developed. If flood control is the primary object, then power generation is a by-product; and the economics of large capital expenditure on power generating equipment must be considered in that light.

Jan 1, 1945

By Charles W. Briggs

The steel foundries of Germany were investigated for the purpose of ascertaining (1) the type and classification of steel structures produced as castings, (2) processing methods, (3) the mechanical properties of carbon and alloy cast steels, (4) the type and character of defective castings, (5) the appearance of castings, (6) research in steel castings, and (7) plant lay-out and equipment.

Jan 1, 1946

By Marco Antonio Falquete

Conventional detonators and blasting caps make use, as igniters, of flame-shock-, andfriction-sensitive primary explosives, such as lead azide, lead styphnate, mercury fulminate, etc, most of them severe toxic and environmental contaminants. Sensitivity of primary explosives is one of the main causes of injuries and fatalities in explosives industry and in field applications. Intense research for a reliable, safe, and environmental-friendly non-primary-explosives detonator was conducted by the industry in the last years. A new detonator is presented, containing no primary explosive, employing only environmental-friendly substances while keeping reliability of performance. A series of performance tests is executed in prototypes of different output energies, including initiation by flame, shock tube, thermo tube (IBQ’s proprietary spark-generating tube, presented at 2005 ISEE Conference), energy transfer reliability, and extreme environmental conditions (according to MIL-STD 331B, test C1 standards). Results are compared, when pertinent, with standard blasting caps of different energy outputs, and with standard primary explosives.

Jan 1, 2007