Search Documents

By R W. Drybrough

The program to increase production at Sherritt Gordon's Lynn Lake property, which began in 1956, included increasing the rope speed and the horsepower of the ore hoist at the "A" shaft. Because of the limited power sup-ply from the two 7,000-hp. hydroelectric plants, and the ? 3,600 hp. predicted for the combined hoisting requirements of the three production shafts, it was considered desirable to lessen the impact of this type of load on the relatively small power system by equipping all future hoisting arrangements with Ward Leonard direct-current drives. The manually operated 8-by 4-ft. hoist at the "A" shaft had a rope speed of 1000 f.p.m., and was driven by a 385-hp., 380-r.p.m. wound rotor motor with liquid rheostat control. This A.C. drive was replaced by a semi-automatic Ward Leonard direct-current drive with a 515-hp., 566-r.p.m., shunt wound motor, providing a rope speed of 1,500 f.p.m. During several months preceding the con-version, all possible preparations were carried out to keep the changeover period to a minimum, and this resulted in a total shutdown time of twelve days. The capability of the "A" Shaft hoist was increased from 109 tons per hour to 134 tons per hour, and both mechanical and electrical maintenance were reduced considerably. The total cost of the conversion amounted to $130,000. The hoistmen who had been required for the manual A.C. drive were transferred to the new Farley shaft, and the reduction in operating labour costs of the "A" Shaft hoist

Jan 1, 1965

By Richard W. Watson

Card-gap and projectile impact sensitivity data are presented for a wide variety of explosive compositions tested at the Bureau of Mines in more or less standard test geometries. The results of both tests are in good agreement in that they provide the same sensitivity ordering for different subclasses of explosives. Least sensitive were homogeneous liquids that did not exhibit a tendency to undergo low-velocity detonation, ammonium nitrate-fuel oil, and most cast military explosives. Of intermediate sensitivity were pressed and powdered military explosives, cast pentolite, permissible and non- permissible water-based explosives, and one commercial two-component explosive. The most sensitive were permissible and nonpermissible dynamites and explosives susceptible to low-velocity detonation.

Jan 1, 1973

By Murad Y. Abu-Farsakh, Md Habibur Rahman

The properties of all natural soil deposits are highly variable, and they are rarely homogeneous. Cone penetration tests (CPT) were used to assess the site variability, which was then incorporated into the Load and Resistance Factor Design (LRFD) of pile foundations. Data from six project sites with multiple CPT tests conducted at various locations were collected for this research. The semi-variogram was used to assess the spatial variability of CPT data (corrected tip resistance, qt) for each location. For each location, the coefficient of variation due to spatial variability (COVR,spatial) was calculated. From COVR,spatial and COVR,method, the total coefficient of variation (COVR,total) for each site was calculated, which was then used to calibrate the resistance factors (ϕspatial, ϕtotal) for use in LRFD pile foundation design. The findings of this study demonstrated the importance of using site variability in LRFD pile design. For sites with lower site variability than the design method (i.e., COVR, spatial < COVR, method), the value of the COVR, total will be decreased, and hence the resistance factors (ϕspatial or ϕtotal) will be increased (credit), and vice versa.

Sep 8, 2021

By Rodrigo Cesar de Miranda

A importância de descrever o processo de beneficiamento por um modelo matemático tem sido apresentada por vários pesquisadores. O principal benefício é o controle e a otimização do processo dentro de uma situação industrial. O modelo seria capaz de prever determinada variável de controle do processo a partir de dados conhecidos. Assim, a simulação dinâmica representa um marco no campo da otimização de processos minerais. Essa tecnologia de simulação tem uma ampla aplicação no estudo de processos, o que permite a obtenção do seu conhecimento e domínio operacional. Além disso, possibilita melhores definições nas etapas de projeto, além de realizar uma análise de confiabilidade mais realista. O presente trabalho consiste em realizar uma análise de confiabilidade, através da simulação dinâmica, para entender como as paradas não-programadas influenciam a produção de uma planta de beneficiamento de ferro. Ainda, visa entender o desempenho fenomenológico dos equipamentos de acordo com a entrada de diferentes tipos de minérios e também como são suscetíveis a condições climáticas.

Aug 17, 2017

Lead removal has been problematic in nickel production by electrowinning from chloride solutions, as developed by Falconbridge. The C12 leach liquor needs to be diluted by electrolyte to allow precipitation of the lead prior to electrowinning. This results in higher solution purification costs and an aversion to consider lead contaminated (secondary) feeds. In this paper, the electrowinning of nickel chloride is carried out in a membrane equipped electrolytic cell. When lead containing nickel solutions are fed into the anode compartment and the anolyte is separated from the catholyte with a cation exchange membrane, lead remains in the anolyte due to the presence of a negatively charged chloride complex. The positive nickel ions migrate preferentially through the membrane to the catholyte, allowing a lower lead nickel cathode to be produced. Lead concentration in the catholyte and the cathode product has been tested as a function of lead concentration in the anolyte. Results are presented and discussed.

Jan 1, 1998

By S. Xu

Magnesium alloy AM50 is of interest to automotive cradle application because of it excellent castability and good ductility. In this work, microstructure and mechanical properties of both low pressure die cast (LPDC) and high pressure die cast (HPDC) AM50 test bars are characterized. Microstructure was examined using optical microscope, scanning electron microscope (SEM) and transmission electron microscope (TEM). Phase identifications were performed using energy dispersive x-ray spectrometer (EDS) and TEM diffraction. It has been found that LPDC produces much coarser microstructure than HPDC. At the same time, the HPDC samples are more heterogeneous in microstructure and composition close to grain boundaries. Particles with various dimensions and morphologies of two different intermetallic phases, Mg17A112 and A18Mn5, were found in all the samples. Mechanical tests were performed under conditions similar to those related to an engine cradle application. LPDC samples show lower strength but better creep resistance than HPDC mainly due to the difference in grain sizes and grain boundary microstructure between LPDC and HPDC. Creep curves are well described by the empirical Andrade equation. Tensile-compressive yield and creep asymmetries were found in AM50, i.e. better deformation resistance in tension than in compression. The average yield asymmetry ratio for all the samples is 0.87. Microstructural examinations on the samples tested in tension, compression and creep showed that the deformation mechanisms in AM50 were slip plus twining at temperatures up to 125°C. The examinations indicate the important role of twining in the asymmetry phenomenon. The creep results indicate that dynamic precipitation of the Mg17A112 phase during testing is not the mechanism directly responsible for the creep asymmetry in AM50.

Jan 1, 2004

By M. W. Lewis, J. Werner

Fluctuating metal prices, declining head grade, and increased operational costs are forcing many open pit mining companies to look to their balance sheets for significant cost reductions in order to remain competitive. Maintenance continues to represent a significant proportion of the total operating costs in the mining industry. Compared with the other major cost components of the mining process, very little effort has gone into maintenance optimization. The potential payoff from maintenance optimization on the cash cost of the commodity is enormous. A large percentage of these costs are incurred in unscheduled maintenance events, which typically cause serious disruptions to the production process. These maintenance-induced production losses can be a significant contributor to the overall operating costs. A structured proactive maintenance approach using the latest advances in technology can achieve dramatic cost reductions and productivity improvements. Remote condition monitoring systems are becoming increasingly commonplace and have the potential to identify problems prior to failure. Detection of equipment degradation prior to failure will enable repairs to be scheduled thereby reducing costs and interruptions to production. Remote condition monitoring technology has evolved rapidly in recent years, with a host of new tools becoming available to assist mine operators in improving their maintenance operations. These tools have capabilities such as remote real-time vital signs and performance monitoring, alarm/event handling, trend analysis, and maintenance workflow management. When these monitoring tools are used in conjunction with a mine management system, the vital signs data can be integrated and associated with maintenance history, predictive maintenance data, operational information, and geographical information. This integrated approach to the management of vital maintenance data will help shift the mobile equipment maintenance paradigm from reactive to proactive. This paper will introduce a proactive approach to the management of the maintenance process and the tools required to facilitate this process.

Jan 1, 2005

By J. G. Stevens, S. W. Colley

"Selective separations of metals and ions in mineral extraction and refining are becoming more challenging as ore bodies become more complex and environmental pressures increase. The separation and containment of mercury produced in gold mining are a factor in the profitability and operability of mines. This paper will discuss the development and implementation of the Johnson Matthey HgFree selective mercury removal process. The process is designed to selectively recover co-leached mercury from either heap leach pregnant solutions at ambient temperature and low mercury concentrations, or electrowinning pregnant solutions at elevated temperature and high mercury concentration, without affecting gold or silver recovery. The process utilizes a highly selective adsorption-desorption step in which mercury is removed quantitatively by the HgFree adsorbent without adsorption of gold, silver or other metals present. Development of the original HgFree adsorbent has resulted in a process whereby mercury can be recovered as an inert salt and is never present as the free metal. The HgFree adsorbent can be regenerated and recycled in situ, and is capable of being reused multiple times. The overall process is compatible with existing gold mining and recovery practices and offers significant environmental and sustainability benefits, including reduction or elimination of the need to retort mercury with a subsequent reduction in potential mercury air emissions. Development of the HgFree adsorbent and process will be discussed along with a pilot operation at two operating mines.INTRODUCTIONMany gold ore bodies contain high concentrations of mercury which when extracted with cyanide, co-extract with the gold and other metals. This mercury is carried through the process with the gold, posing environmental and technical issues when it is separated from the doré. This paper describes a method to selectively adsorb mercury from the gold recovery circuit while it is in a soluble form, leaving gold to be processed as normal. The removal of mercury from the circuit eliminates the need for mercury retorting of doré and so reduces the potential environmental impact of fugitive emissions of elemental mercury."

Jan 1, 2016

By Juan Anes, Omar Godínez, Adrián Tolentino, Mario Franco

Como aplicación práctica de las herramientas hidrodinámicas de flotación desarrolladas por Flottec, McGill y otros investigadores, el objetivo del estudio fue crear, para Minera Fresnillo, una herramienta preliminar de control de procesos, a nivel de la primera celda de la flotación primaria del circuito de plomo, con el fin de expandirla luego a toda la planta. El trabajo determinó ecuaciones matemáticas que describen las relaciones entre las variables de proceso e hidrodinámicas para aumentar la recuperación de plata mientras que disminuye la cantidad de insoluble al concentrado. Se desarrolló usando diseño de experimentos con tres variables (nivel de espuma, adición de espumante en ppm, y flujo de aire en cm/s) para observar los cambios en la recuperación de plata y plomo.

Sep 20, 2019

By Paul Riches

Today’s steel producers face the dual challenge of ensuring on-time delivery and ever demanding product requirements, while also running a lean operation. Every day the management of a long rolling plant requires continuous optimization of both operating and business practices. Imagine a long rolling facility, where individual pieces of equipment communicate with each other, where sensor information can be used not only for control purposes but to also monitor the condition of the equipment, where models are used to verify the process is within working limits and the equipment raises alerts to operators when it requires maintenance! Utilizing the ongoing evolution in technology though data collection, communication, internet of things, control techniques and smart sensors, there is now more information available than ever before. The collection and analysis of this information will both advance control and monitoring of plant performance; revolutionizing long rolling mill plants worldwide and optimizing the entire value chain, along with improved and more flexible production.

Oct 30, 2017

By Paul F. Kerr

QUARTZ of a certain kind, is one of our strategic minerals, and Brazil is probably the one important available source. Crystals of quartz of suitable size and perfection for piezoelectrical application are rare; their most outstanding use is in radio work. Clear quartz, or "crystal," free from twinning, cracks, foreign particles of other disturbing lines of growth, and gaseous or liquid inclusions, is cut into plates which provide excellent control of frequency in broadcasting. The squares or rectangles are less than a millimeter in thickness and ordinarily on the order of 1 in. along each side. They are cut at definite angles with respect to the axes of the crystal, and ground with opposite surfaces parallel. Each small slab must be a section of one crystal, uniform throughout in atomic alignment. The thickness of the chip controls the frequency of a broadcast and it is most important to have the plates oriented and ground with utmost precision. Opposite surfaces are parallel to within 0.001 mm. and expansion or contraction due to the temperature is limited to one part in a million.

Jan 1, 1942

By Linda D. Raedeke

The main platinum-group metal (PGM) deposit in the Stillwater Complex is associated with a stratiform zone formed by magma mixing. In general, the intrusion is a large, layered body of Archean age which formed by repeated magmatic injections in- to a single, large, hypabyssal magma chamber. The Complex is broadly divided into the lower Ultramafic series of olivine ± orthopyroxene rocks (1000-2000 m thick) and the upper Banded series of predominantly plagioclase-rich rocks (24500 m thick). The latter is further divided into Lower, Middle, and Up- per Banded zones. The Ultramafic series, plus most of the Lower and Upper Banded zones formed from repeated injections of an olivine-saturated magma, the rocks accumulating from the floor upward with a crystallization order of olivine, or- thopyroxene, plagioclase, clinopyroxene. The olivine-bearing subzones of the Middle Banded zone formed predominantly from a magma which crystallized in the sequence plagioclase, olivine, clinopyroxene. Olivine-bearing subzone I, with which the PGM mineralization is associated, occurs generally -400 m above the Ultramafic series-Banded series contact. Ore grade mineralization is usually found in plagioclase or plagioclase-olivine cumulates. The platinum-group elements are associated with disseminated base-metal sulfides dominated by the assemblage, pyrrhotite-chalcopyrite-pentlandite. Olivine-bearing subzone I marks an interruption in the crystallization sequence of the Lower Banded zone, with the reappearance of cumulus olivine and an associated change of the crystallization sequence. These changes indicate the addition and mixing of a secondary magma of the same composition as that which later dominated in the formation of the Middle Banded zone. Characteristics associated with mixing include laterally discontinuous but well-developed layers, xenoliths of ultramafic rocks, and sedimentary-type structures such as slum- ping and graded layering. The influx of new magma caused sulfide saturation by one or more of several chemical changes including addition of sulfur, decrease in oxygen fugacity, decrease in FeO, or increase in SiO2. Once an immiscible sulfide liquid was formed, platinum-group elements were scavenged from the magma by the sulfide liquid and segregated.

Jan 1, 2013

By R. K. Steinhorst

Multivariate cluster analysis, MANOVA, canonical analysis, and discriminant analysis of hydrochemistry data were used to investigate the directions of ground water movement in basalts in the vicinity of the Hanford Reservation, Washington. The statistical analyses indicate that the hydrochemistry of the ground waters in these basalt formations is distinctly different on each side of the Columbia River. This suggests that the river is a ground water divide or that the river is roughly coincident with a hydrogeologic barrier boundary. The statistical procedures used in this study constitute a quantitative means for differentiating ground waters according to hydrochemistry.

Jan 1, 1990

By C. S. Giggins, F. S. Pettit

The oxidation properties of Ni-Cr alloys with fine grains, coarse grains, and deformed surface layers have been studied at temperatures of 900" and 1100°C in 0.1 atm of oxygen. The oxidation rates of alloys containing between 10 and 30 wt pct Cr have been found to be dependent upon the grain size of the alloy. Finegrained alloys had smaller oxidation rates than coarsegvained alloys because of the selective oxidation of chromium at alloy grain boundaries. In this compositional range alloys with deformed surface layers behaved similar to fine-grained alloys due to recrys-tallization of the deformed surface layer. In the preceding paper1 it was found that during the oxidation of Ni-Cr alloys, the volume fraction of precipitated Cr2O3 could be greater at alloy grain boundaries than at other areas of the alloy surface. In the case of alloys with chromium concentrations equal to or greater than 30 pct,* the volume fraction of Cr2O3 *AIL compositions are given as weight percent unless specified otherwise. precipitated at grain boundaries and within grains on the alloy surface both exceeded the critical amount required for lateral growth of the Cr2O3 particles and the surfaces of these alloys were completely covered with a continuous, external layer of Cr203 during oxidation. However, in the case of alloys with chromium concentrations between approximately 5 to 30 pct, the volume fraction of precipitated Cr2O3 exceeded the critical value required for external scale formation only at grain boundaries.but not within the interior of the grains. Consequently, the surfaces of these alloys had external scales of Cr3O3 over the grain boundaries but internal Cr2O3 subscales with external scales of NiO away from the grain boundaries. Under these latter conditions, it was found that chromium could diffuse laterally in the alloy from those areas covered with an external layer of Cr2O3, i.e., grain boundaries, to areas where the Cr2O3 was present as a subscale. This diffusion of chromium resulted in an increase in the volume fraction of Cr2O3 precipitated in the sub-scale zone and continuous layers of Cr2O3 could be formed at the subscale front in these regions. For the alloys used in the previous studies,&apos; continuous layers of Cr2O3 were formed on Ni-20Cr alloys in the subscale regions after approximately 30 hr of oxidation at 900°C. For shorter periods of oxidation, the Cr2O3 layer was semicontinuous with the continuous portion at the subscale front emanating from points where the Cr2O3 had been formed as an external scale over alloy grain boundaries. Some lateral growth of a Cr2O3 layer in the subscale region was observed on Ni-15Cr and even Ni-10Cr alloys but this layer was never continuous after 30 hr of oxidation. These results indicate that the selective oxidation of chromium in Ni-Cr alloys with chromium contents between 5 to 30 pct may be dependent upon the grain size of the alloy. Fine-grained specimens in this compositional range should have a larger fraction of the surface covered with external Cr2O3 than coarsegrained specimens and the subscale areas required to be sealed via lateral diffusion of chromium should be smaller. It is therefore to be expected that a continuous layer of Cr2O3 can be formed on alloys in this compositional range after short periods of oxidation providing the alloy grain-size is sufficiently small. bo studieS2,3 have established that the oxidation behavior of alloys can be significantly influenced by pretreatments which produce mechanically deformed surfaces. It has been found that deformed surfaces usually promote the selective oxidation of elements in alloys and it is believed that these effects are due to rapid diffusion of elements in the deformed layer. In view of the previous results,&apos; which showed that alloy grain boundaries may play an important role in the selective oxidation of chromium in Ni-Cr alloys, deformed surfaces may promote the selective oxidation of elements in alloys as a result of the numerous grain boundaries formed on the alloy surfaces via recrys-tallization during heating to the oxidation temperature. The purpose of the present studies was to determine the effect of alloy grain size and surface deformation on the selective oxidation of chromium in Ni-Cr alloys at temperatures of 900" and 1100°C in 0.1 atm of oxygen. EXPERIMENTAL The average grain diameter of the alloys used in the previous studies1 was not less than 0.04 mm and alloys with compositions between 5 and 30 pct chromium had average grain diameters between 0.04 and 0.14 mm. Since the oxidation kinetics were already available for these relatively coarse-grained alloys, it was desirable to use these same alloys in the present studies. The surfaces of the alloys listed in Table I of the previous paper were deformed by using a Model F S.S. White Industrial Airbrasive Unit, which delivered a controlled mixture of 25 µ Al2O3 particles in a stream of dry air at high velocity against the surface of a specimen. The amount of surface deformation produced by this treatment was not determined but a re-crystallized layer about 15 µ thick was formed upon annealing deformed specimens. The grain size at the surface of the specimens was reduced to an average grain diameter of 0.01 mm by annealing the deformed specimens, i.e., grit-blasted,

Jan 1, 1970

By A Dal-Corobbo, R Zick

The coal mining industry is now faced with new regulatory requirements that limit the discharge of chlorides into receiving streams. To meet these new regulatory standards for treated mine water, a zero liquid waste approach was developed using advanced treatment technologies. The approach described in this paper will generate clean water for reuse in various energy endeavours or discharge to the environment, with no substantial liquid or solid waste from the treatment process leaving the site.CITATION:Dal-Corobbo, A and Zick, R, 2013. Zero liquid discharge in coal mining operations, in Proceedings Water in Mining 2013 , pp 221-226 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By Stefan K. Schwank

The paper describes the two foundation techniques - mini piles and postgrouted bored piles. The mini pile system is presented with its design and installation parameters, especially the drilling technique. Two case histories demonstrate the application under extremely limited space and traffic conditions and the required modifications of the equipment. After the description of the postgrouted bored piles and its grouting technique, the paper gives a comparison of postgrouted piles and standard piles on a large basic test in Germany. The Brooklyn Queen&apos;s Expressway, N.Y., case history shows the application of this technique after redesign of the original proposal. 1. General Increasing requirements to improve existing foundations to carry additional loads and to increase the bearing capacity of bored piles leads to two new piling techniques: the mini-pile and the post grouted bored pile.

Jan 1, 1991

By T. Sterry Hunt

Jan 1, 1884

By M. H. Shumate

Rope-type haulage has had many applications in the mining and allied industries. Records have indicated favorable results both from a standpoint of efficiency and investment. The Truax-Traer Coal Co. has used some variations of rope haulage at their mines and preparation plants. They have built a system which solves their particular problems, and have an investment which has indicated an annual savings in operating costs. Rope haulage, as applied to the mining industry, goes back many years for both underground and surface mining, or a combination of both. The Truax-Traer Coal Co. has used gravity retarding hoists as well as several variations of rope haulage, including electrical and combinations of both, but each was limited in its use and application by natural conditions and economies of the operation. Several systems of rope haulage equipment are offered by manufacturers today for handling railroad car movement on a limited or continuous basis. The portal and railroad loading facilities of Truax-Traer Coal Co.&apos;s Burning Star Slope mine, located in Jackson County, Ill., were moved in 1960. The old location was abondoned, eliminating 3% miles of underground track haulage. The mine was converted to an all-belt system, and coal is loaded at a new raw coal plant and shipped by railroad cars to a central cleaning plant. The company wanted to operate the surface facilities as efficiently as possible, employing a minimum number of workers, using the latest type railroad car movers. The existing rope haulage facilities at several locations throughout the country were examined and considered for the Slope mine location. The application of each appeared favorable but lacked flexibility, and it was difficult to justify the capital investment. The company decided to investigate the possibility of building a system that would apply to their problem, and have an investment that could be amortized in a relatively short period. SPECIFICATIONS They employed the services of Allen and Garcia Co. of Chicago, Ill. Through combined efforts, a railroad car rope system was designed to specifications as shown in Fig. 1. The Falk Corp. of Milwaukee, Wis. built the hoist to the specifications as shown in Fig. 2. It has an all welded base and pedestals. The all welded drum is not grooved. A single helical gear was used in lieu of herring bone type. A Falk speed reducer, Unit 90Y3-A, is driven by a 25-hp 1800-rpm, 440-V ac type &apos;C&apos; (high starting torque) drip-proof, Frame 324-U motor. The speed reducer shaft is equipped with a solenoid operated ac spring set shoe brake, operating on a 7-in. diam. brake wheel. The dolly car, shown in Fig. 3, was field constructed, using the trucks and frame of a railroad tank car. Truax-Traer did not alter the frame but added plates and anchors for hoist ropes and frames for 8.5 tons of concrete to be used as ballast on the car. The limit switch operating shoe was also installed and the car coupler latch mechanism overhauled. The hoist rope selected was 1% in. in diam., 6x37 improved plow steel extra flexible, right lay, regular lay, with independent wire rope core, and preformed. Wedge sockets were used to connect rope to the dolly car as shown in Fig. 4. The system employs two 30-in. and three 16-in. diam. sheaves. All are bronze bushed and equipped with grease fittings. Larger sheaves are used for directional change of hoist rope and the smaller ones as snub sheaves to correct fleet angle of rope as it approaches the hoist drum. The Trench lay cable, buried between the two tracks, is used for electrical distribution and controls between hoists and operator&apos;s cab. Foundations for the system required 187 cu yards of reinforced concrete using approximately 60 cu yd each at three locations. Four hoists are employed in the system, two for each track. A pair is interconnected electrically and when one operates, moving the cars, the tail hoist idles with brake released. The process is repeated for the reverse direction. A limit switch, mounted in the track near each end of the system, is tripped by the dolly car as it approaches the hoist. The limit switch controls movement in one direction only, protecting the dolly car and establishing positive con-

Jan 1, 1962

By Ervin P. Fuchs

Volume II of this report presents the vibration data, octave band data, one-third octave band data and narrow band (amplitude versus frequency) data for ten mining machines. These ten mining machines include a Goodman 968-2 Loading Machine, a Lee Norse 245 Continuous Miner, a Jeffrey 120L Continuous Miner, a National Mine Service 3080 Continuous Miner, Acme D-1 Roof Bolter, a Lee Norse 265 Continuous Miner, two Jeffrey Locomotives, a Joy CD-71A Coal Drill and a Jeffrey 100L Auger Miner. Volume J of this report presents the effects of underground environment and loading conditions on noise levels of coal mining equipment

Jan 1, 1979

By Jonkion M. Font

An expression for the distribution ratio of arsenic between slag and copper matte or liquid copper was developed by both, an extension of the Reddy-Blander model for deriving a priori the arsenic capacity, and by a relationship between the arsenic capacity and the arsenic distribution ratio. In this study, the a priori arsenic capacities in the FeO-SiO2, CaO-SiO2, MgO-SiO2, FeO-CaO-SiO2, FeO-FeO1.5-CuOo.5-MgO-SiO2, FeO-FeO1.5-CuO0.5-CaO-MgO and FeO-FeO1.5-CuO0.5-CaO-MgO-SiO2 slags were calculated at 1573 K. The a priori arsenic distribution ratio between the FeO-FeO1.5-CuO0.5-CaO-MgO-SiO2 slag and copper matte (L s/m as), and between the FeO-FeO1.5-SiO2 or FeO-FeO1.5-CuO0.5-CaO-MgO slag and liquid copper (L s/Cu as) were calculated. The model calculated data are found to be in good agreement with the reported experimental data. The availability of reliable thermodynamic data for slag components and impurities in the slag-matte-metal system is essential for the accurate prediction of impurity capacities and distribution ratio data. The arsenic distribution ratio model developed here, can be extended for prediction in multi-component slags and mattes or liquid metal, and thereby may lead to the development of new slag systems for the efficient removal of arsenic in the copper smelting, converting and refining processes.

Jan 1, 2003