Search Documents

By D. H. Woodard

One of the principal uses of polarized light in metallurgy is to show the granular structure of metals by contrasting reflections. This use is confined largely to anisotropic metals, such as beryllium, tin, magnesium, and the like.1 Recently, Hone and Pearson2 have extended the use of polarized light to include the isotropic metal aluminum. This was made possible by the formation of an anodic film that was optically anisotropic and that had a fixed and reproducible structural relationship to the grains in the substrata. With their method, it was possible to indicate localized textures in annealed aluminum sheet. In the course of an investigation of plastic deformation at the National Bureau of Standards, it was found that the isotropic single phase alloy Monel could be made optically anisotropic by treatment with the usual Monel contrast etchant. Experiments soon showed that dif- , ferences in orientation could be detected easily. Previous investigations involving the use of polarized light have been restricted to annealed metals. In this paper it will be shown that inhomo-geneous plastic deformation which results in lattice bending and development of deformation bands, experienced by individual grains in polycrystalline Monel, is revealed in the microstruc-ture. This interpretation of the micro-structure was confirmed by a study of slip lines formed after prior plastic strain. Materials and Procedure The material used was Monel, the chemical composition of which was C—0.17 pet, Mn—1.28 pet, Fe—1.61 pet, S—0.009 pet, Si—0.17 pet, Cu— 30.70 pet, Ni—66.04 pet. The material was divided into 2 lots which were treated as follows: Lot A was heated at 1700°F for 3 hr to produce a fully annealed, coarse grained structure. Lot B was heated at 1400°F for 1 hr to produce a close approximation of a fully annealed structure without appreciable increase in the grain size of the original material. After each of these heat treatments the material was cooled in air. Samples for metallographic examination were cut from tensile and compression test specimens and were prepared by grinding on lead-tin laps, followed by electrolytic polishing, † Etching and the development of ridges were avoided by keeping the voltage above 3.8 and by preventing contamination of the polishing solution with water. Monel, when polished and treated with most etchants, is optically isotropic. However, when given a light etch for about 4 sec with the Monel contrast solution the surface of the metal becomes optically active. The microstructure when observed under crossed nicols* appears different from that viewed by ordinary light. This is shown by a comparison of micrographs made of the same area of a plastically deformed specimen using polarized light (Fig la) and white light (Fig 16). If Monel, which has been lightly treated with the contrast etchant, is slightly deformed by compression, rectangular figures are apparent over the specimen. However, within too short a period to be photographed, these rectangles become circular, probably because of surface tension effects within the etched film. The two observations,

Jan 1, 1950

By Thomas C. Shapiro

Introduction In recent years - even months - the number of articles on computers has increased rapidly. One can hardly pick up a newspaper or magazine without seeing a computer-related article. The article usually explains how the computer will change our lives. Many of us have some concern about the nature and type of change. For most of us, though, the problem is lack of information and understanding about how computers work. In other words, how do we make cost-effective decisions about computers? This three-part series will explain, simply, what a microcomputer is, how it works, and how to decide if you need one. This first article will define terms and briefly discuss areas where computerization might be economic. The second article will discuss geology and mining applications. The third article will discuss plant, administrative, and geotechnical areas as well as the future of software development in the minerals industry. Terms and Concepts All computers have input and output devices and a central processing unit (CPU). Information - instructions and data - is communicated to the computer by means of input devices. These instructions to the computer are converted into language that the computer understands. This causes the instructions to be carried out in the CPU. The result of these operations is translated back into language that we understand. This information is then sent to output devices such as printers and video display tubes. Traditionally, peripherals were devices separate from the main-frame (the CPU and memory) and were used to input, output, and store information or instructions. Today, peripherals perform the same functions though they may be housed in the same cabinet as the CPU and memory. Historically, peripherals included all input and output devices not part of the mainframe. Input devices include keyboards, magnetic tape, and card readers. Tapes and disks are input as well as output devices. Output devices are printers, CRTs (Cathode Ray Tubes), and any mass storage device capable of storing data when directed to do so by the computer or the program. In fact, any mass storage device that can give the computer data when requested is an input device. Mass storage devices include floppy disks (thin, round sheets of plastic covered by metal particles), and hard disks. The latter are thicker and more densely coated with metal particles. This allows much more information to be stored. Another type of mass storage is magnetic tape. Its type and size varies widely. Processing and Storage Any computer understanding must include how instructions and data are processed and stored. Information is stored as a positive or a negative field known as a "bit." There are eight bits in a byte. The bits can be represented as either a one or a zero. Thus the code for a byte representing the numeral one is 00110001. The byte representing the letter A is 01000001. These codes are from the American Standard Code for Information Interchange (ASCII). ASCII defines the standard set of characters including alpha, numeric, and special characters. The computer's memory has allocated locations where instructions as well as incoming information can be stored. All information and instructions are stored as binary numbers bit by bit - zeros and ones. The amount of data that can be stored is referred to as either thousands or millions of bits or bytes. The letter "K" is used to designate one thousand units. The letter "M" is used to mean one millon units (one meg). Disks Thus, a 113-mm (5 1/4-in.) floppy disk - double sided and double density (DSDD) - contains 320,000 bytes (characters) or 320K. This is about 164 double-spaced, type-

Jan 2, 1984

By Volkan Arslan

This study aimed to remove the contaminants in quartz sand by using an eco-friendly method and to obtain high-purity quartz. For this purpose, ultrasound-assisted acid leaching was applied. Equal amounts of a mixture of diluted hydrochloric and oxalic acids were used as the solvent. Response surface methodology (RSM) was used for optimizing, modeling, and predicting the experimental parameters. The correlation coefficient ( R2) of the proposed quadratic model for the relationship between iron removal yield and test parameters was calculated as 0.9731 and it was determined that the predicted and actual values were compatible. Finally, optimization experiments were made and optimum experiment conditions were revised and determined as 83.38 °C of leaching temperature, 196.35 min of leaching time, 2.86 M of acid concentration, and 202.24 W of ultrasound power. Under the optimum conditions determined after optimization, the highest yield of iron removal was determined as 95.08%. Under the optimal parameters, the SiO2 content of the concentrates increased from 97.841 to 99.907% and the Fe2O3 content reduced from 0.225 to 0.011%.

Jul 12, 2021

By Alejandro Lagos

El modelamiento estructural de una zona es esencial para la búsqueda de zonas favorables para la mineralización. En ese sentido, el presente texto describe la geología estructural de las áreas de Cajamarca, San Marcos y Bolivar y su posible relación con la génesis de los yacimientos de minerales ubicados en ese sector y así diseñar un modelo estructural de las aéreas mencionadas apoyado por el método de mapas paleogeológicos.

Sep 14, 2009

By Samuel Canchanya M

El presente trabajo señala la eficiencia de los métodos geoestadísticos en la industria minera a través de diversos ejemplos aplicados en yacimientos peruanos. En este sentido, los métodos estadísticos desplazan a los métodos tradicionales puesto que ofrecen mayor precisión, objetividad y eliminan la relativa accesiblidad de los depósitos minerales. Asimismo, el texto describe las diversas explicaciones de su aplicación en el campo de la ingeniería industrial, topografía, geofísica y batimetría en la industria del petróleo, al tiempo que refiere las causas de su escaso empleo como método teórica en la explotación de la industria minera.

Nov 8, 1984

By Kenneth K. Landes

So far my consulting in industrial minerals has been confined principally to carbonate rocks,-salt, coking coal, and glass sand. Much of this work has been for companies either too small for a full-time geological staff or unaware of the value of employing one or more qualified geologists permanently. It gave me considerable personal satisfaction to see several of the latter companies employ one or two full-time geologists after the completion of a consulting contract with them. One possible reason why some companies lack the wisdom to hire geologists is that they are dominated by engineers who still subscribe to the old idea that engineers are self-sufficient in all fields. They could have learned this from their professors. I once knew a Dean of Engineering who got purple in the face when a faculty committee was discussing the financing of a broad gauged engineering project and suggestions were made that assistance be obtained from the Schools of Business and Law and from some of the science departments tie pounded the table and shouted "Engineers are trained to handle all this!" In teaching engineering geology some years ago I used to tell the class repeatedly that the course would not make them geologists, that the purpose was to teach them

Jan 1, 1972

By Bogidar V. Mihaylov

Bacterial oxidation of a low-grade sulfide gold ore was investigated in order to enhance leaching of gold. The experiments were carried out in columns using mixed cultures of Thiobacillus ferrooxidansisolated from the ore. Fractions with different screen analyses were oxidized in two regimes - one pass of the solution and circulating, solution. Constant temperature and flow-rate of the percolating solution were maintained during the experiments. A correlation between the concentrations of copper and iron in the solution leaving the columns and pH and Eh values was observed. The effect of bacterial activity was proved by means of thiourea and cyanide leaching of the oxidized ore.

Jan 1, 1991

By Shengli Wu, Wei Huang, Xinliang Liu, Kaifa Zhang

The slagging behavior, the phase of primary blast furnace slag and its transformation law of structure for the single furnace burden were studied in this paper. The results showed that the formation of primary slag was controlled by CaO/SiO2, Al2O3 content, MgO content, reducibility, iron content and porosity of the furnace burden. Fayalite (2FeO•SiO2) was easily formed from acid ferrous furnace burden while kirschsteinite (2(Fe,Ca)O•SiO2) was produced from alkaline ferrous furnace burden

Jan 1, 2015

By Walter O. Snelling

Continuation of the discussion of the paper of WaltER o. SnelLIng, presented at the New York and San Francisco meetings, February and September, 1915, respectively, and printed in Bulletin No. 100, April, 1915, pp. 695 to 704 and Trans., li, pp. 657 to 671. A. C. McLaUghlin, San Francisco, Ca1.—It seems to me that Mr. Snelling's work, if it is what it appears to be, is one of the most important contributions to petroleum technology that has been brought out in the last 25 years. If his end products are what they seem to be, he has made. a discovery, which, in my judgment, will revolutionize the petroleum industry. As to industrially carrying out these processes I do not think there is the slightest difficulty, for I have had some work recently where crude oils were handled successfully at a temperature of 750" F, and pressure of 750 lb. per square inch. William A. WillIams, San francisco, Ca1.—What metal did you use, Mr. McLaughlin? A. C. McLauGHILIN.—Ordinaly seamless tubing, extra strong. William A. Williams.—Tests were made in Dr. Rittman's experimental plant at Pittsburgh, upon samples of residuum furnished by Mr. Bell, the residuum being the remainder of the crude oil after the lighter fractions had been removed. After the material had been run through Dr. Bittman's plant, yields of from 43 to 58 per cent. of material, boiling under 150" C. were obtained. The distillate had a peculiar odor, due to the presence of benzene, toluene, and other unsaturated hydrocarbons. W. N. Best, New York, N. Y.—What is the difference between the Rittman and the Snelling process or system? William A. Williams.—he fundamental difference is that reactions take place under relatively higher temperatures and pressures and with none of the oil present in its original or liquid state, while the reactions secured by Mr. Snelling and other investigators have been from the liquids in the presence of some vapors. Under such conditions as Mr. Snelling operates, the temperatures and pressures used are limited and the flexibility in the control of these variables is extremely limited when compared with the Rittman process.

Jan 1, 1916

By Patrick J. Cain

The fatigue-failure characteristics under high-frequency (10 KHz) cyclic loading were determined for a marble, granite, and quartzite. The rock speci-mens were cyclicly loaded (using a high-power piezoelectric sonic transducer) at a constant strain amplitude generated by forming a longitudinal standing stress (strain) wave in the cylindrical test specimen. The number of load cycles required to fail each rock type at a given strain amplitude was deter-mined. The fatigue fractures were tensile in nature and the fracture load amplitudes were as low as 30 pct of the static tensile strength. Also the internal heating of the rock caused by the material damping (internal friction) was measured. The damping and internal heat generation in the specimens was analyzed to show that nearly all of the power input can be accounted for as a change in enthalpy in the specimen. Using these results the thermal strain in the rock was calculated to evaluate its contribution to fatigue failure. The thermal strain was found to range up to 30 pct of the dynamic strain amplitude depending on the load amplitude and the number of load cycles. The specific energy required for failure was determined and possible applications of the high-frequency fatigue fragmentation process are discussed.

Jan 1, 1975

By B Bonfils, P Lois Morales, C Evans

One of the main challenges for current and future mining and processing methodologies is to understand the characteristics of the rock so that its behaviour in one or more parts of the mining process chain can be predicted. Features such as rock texture, mineralogy or border complexity between minerals control how the rock behaves from the processing plant through to the final products, including tailings disposal and thus can affect the feasibility of the project from technical, economic and environmental impact perspectives. Understanding how the mineralogy and texture of rock affect its behaviour in mineral processing is a demanding area of research and is essential knowledge in predicting the processability of complex ores in different stages. This study aims to demonstrate that different types of relevant information can be extracted from a range of currently available analytical methods. However, this information can be used in a complementary way for building a more comprehensive rock characterisation at the microscale and better-predicting ore processing characteristics from the intact rock through to tailing disposal. CITATION: Lois Morales, P, Evans, C and Bonfils, B, 2018. Multisource rock characterisation at microscale for a better understanding of processing characteristics, in Proceedings Complex Orebodies Conference 2018, pp 44–48 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By J. C. Gathje

The Robinson copper ores were mined for many years from pits containing varying ore grades, sulfide and oxide ore types, and differing mineralogy. The ores also contain gold and molybdenum values, and their recoveries are an integral part of the flowsheet development. Metallurgical responses were characterized using a standard flotation procedure. Further studies investigated primary and regrind particle sizes, reagents, and other variables. The metallurgical testing was supported by mineralogical studies. Results demonstrated a high degree of metallurgical success for flotation. Final copper concentrates ranged in grade from approximately 28 to 30% copper and copper recoveries were 89 to 95% based on laboratory and pilot plant data.

Jan 1, 1992

By Yuanming Pan, Brett Rogers, Baoquan Hu, Gary Yeo, Christine Austman

The nature and distribution of radiation-induced defects (RIDs) in quartz from the Maw Zone, a yttrium- and rare-earth-element-enriched sandstone breccia complex exhibiting intense hydrothermal alteration, have been investigated by electron paramagnetic resonance (EPR) spectroscopy. EPR spectra show that detrital quartz in sandstone, from five diamond drill holes intersecting the Maw Zone and one above the crest of the so-called Quartzite Ridge, contain only background-level RIDs, indicating that Ubearing fluids were absent in this area. However, close to the sandstone-basement unconformity, in hole WR-194 immediately west of the Quartzite Ridge, the concentration of RIDs in detrital quartz is significantly above background but at least an order of magnitude lower than those at the Key Lake and McArthur River deposits. Widespread drusy quartz at the Maw Zone, which signifies intense hydrothermal alteration, is associated with hematite-, sulfide- and carbonate-bearing mineral assemblages, which exhibit complex crosscutting relationships. EPR spectra of drusy quartz in all three types of mineral assemblages are low in RIDs as well, supporting the EPR evidence that fluids at the Maw Zone did not carry significant U. These EPR results suggest that, in spite of intense hydrothermal alteration and favorable structural geology, the Maw Zone is unlikely to host any significant U mineralization. Moreover, this study shows that the EPR technique is potentially a useful exploration tool, capable of determining whether individual alteration zones in the Athabasca Basin were associated with U-bearing fluids or not.

Jan 1, 2013

By Harold L. Lovell

Problems associated with fines (minus 6 mm, 1/4-inch) production, preparation, and utilization have long plagued the coal industry and are now more acute than ever. Continuous deep mining systems create more fines which have moisture; content greater than natural levels from dust control spraying and often add substantial levels of mineral matter due to mining selectivity constraints. Frequently, during preparation, more -fines are developed to achieve improved component liberation. Coal consumers often specify small sizes whether for carbonization, combustion, or conversion. Wet beneficiation systems process fines by several' types of unit operations, but usually must also incorporate costly and complex dewatering systems to reduce the moisture content of the products. Existing pneumatic preparation systems are constrained between product equality and yield by the sharpness of separation. These limitations become more severe with decreasing particle size and increasing feed moisture content. Control of particulate emissions, both process and fugitive, during pneumatic preparation, can be forbidding. A pneumatic preparation-process which would overcome these constraints, could be most enticing. The DryFlo system is being evaluated to quantify performance characteristics as regards these constraints.

Jan 1, 1976

By L. Salnais

"Aluminum alloy structural components f or aircraft designed prior to the early 1970s, were machined from 2024, 7075 and 7079 plate, bar and forgings in either the T3xxx of the T6xxx tempers. Protective treatments for these parts consisted of chromic acid anodizing and alkyd zinc chromate primer, plus a nitrocellulose lacquer for exterior parts.The major service problem with these parts was the frequent occurrence of exfoliation corrosion and stress corrosion cracking (S. C. C.). Therefore, 2024 and 7079 alloys, with min or exceptions, were not used in aircraft designed after the early 1970s. Replacement materials were 7075 and 7050 alloys in the overaged, exfoliation corrosion and S. C. C. resistant, T73xxx tempers.The use of improved materials together with the upgrading to chromated epoxy primers, polyurethane enamels and the introduction of water displacing corrosion inhibiting compounds have significantly reduced corrosion in aircraft. IntroductionThe prevention of corrosion in aircraft has been a challenge to aircraft designers for many decades. With the design of the first all-metal aircraft, the designer and builder were thrust into the relatively new field of protective treatments as corrosion started to become more prevalent. This resulted from the continually increasing importance and wider utilization of aircraft, and their exposure to a wider variety of ho stile environments such as urban industrial pollution, high humidity tropical areas and salt ladened marine environments.Corrosion advanced another significant step when, after World War II, designs of new and larger aircraft utilized larger and thicker metal sections in the manufacture of structural components. With thicker mill products came higher residual heat treat, fabrication and assembly stresses resulting in an increased number of stress corrosion and exfoliation corrosion problems.Apart from the exterior environment, aircraft interior s can be exposed to a number of fluids which are either directly or indirectly responsible for corrosion. The most common of the fluids is water which is usually introduced as a result of condensation, especially in pressurized fuselages, and spillage from lavatories, galley s and electrolytes from batteries. These fluid s have a degrading effect on protective treatments and are also corrosive to the substrate metal. Fluids such as phosphate ester hydraulic fluids and ester based turbine engine lubricating oil s are not corrosive to the substrate metal, albeit they do contribute to corrosion by the degrading effect on protective treatments."

Jan 1, 1988

By David A. Lipton

U.S. Bureau of Mines personnel examined mines, prospects, and mineralized areas to determine the mineral resources and potential of the Moses and Dennison Peak RARE II areas in Tulare County, California. These areas, along the west slope of the Sierra Nevada, are underlain by grarnitic rocks of the Sierra Nevada batholith and contain numerous metasedimentary roof pendants. Silver, copper, and zinc occur in contact-metasomatic deposits within the metasedimentary rocks. In the Moses area, the Powell Mine (fig. 1) contains an estimated 90,000 tons (82,000 t) of subeconomic silver, zinc, and copper resources. The King Solomon Prospect has 3,000 tons (2,700 t) of silicified phyllite containing zinc. On the Helen-Joyce Prospect, 44,000 tons (40,000 t) of gossan occur above a poorly exposed silver-zinc rich zone. Potential exists for additional mineral resources and occurrences at each of these properties.

Jan 1, 1983

By D. Berman, A. Brodt

"Delivery of all volume of mined mass on the terrestrial surface results not only in irrational power expenses on moving of huge volumes of dead rock as a part of initial raw materials (especially vertically) on long distances, but also necessities of storing tailings in open-air. Thus, in bowels of earth, huge volumes of the developed space are formed. However, the nature doesn't suffer emptiness. As consequence, through the process of underground mining works, in earth bowels starts intensive development of rocks dislocation processes involving subsidence of terrestrial surface, and with it, begins irreparable damage every objects which are on that territory. Highly effective new methods of underground concentration of the various minerals, which deliveries of only target component on terrestrial surface integrally connected with transport process in stream and subsequent deliveries to destination in continuous mode by the long distance hydrotransport, allow not only to eliminate a construction of concentrating factories on the surface, but also storing of tailings of concentration process on open-air preventing dislocation of rocks, thanks to operative placing tails in the underground developed space. Surely, the main problem in the development of such gravity dressing technology is the problem of finding the optimal formula for the heavy liquid that will fill such system in close connection with the procedure of its full regeneration. The requirements for such liquid are being non-toxic and cheap. This question was solved successfully."

Jan 1, 2014

By Mihir B. Roy

"Coal transported by rail for Thermal Power Plant in Haldia, West Bengal, India, was to be received and stored in Coal Complex comprising of Wagon Tippler, Track Hopper, Junction Houses and network of horizontal and inclined tunnels. The site was very soft with high ground water level. Deep excavation and dewatering posed great difficulty. Original plan was to drive about 1000 m of steel sheet pile and well sinking which had major impact on cost and time. High ground water was identified as the main problem. Controlling water level and maintaining it would allow open excavation over major areas. Scheme for lowering aquifer with one and two-stage well-point dewatering system was developed following basic principles of groundwater and seepage. Arrangements of wells, installation and pumping were worked out in detail. Water levels could be lowered below bottom levels of excavation. Design of sheet pile was modified under lowered ground water condition. Overall length and depth of sheet pile were reduced drastically. Open excavation was possible in segments over major areas. The scheme was highly successful in smooth and fast progress of underground works. The works were completed safely months ahead of schedule time and with significant saving in cost.INTRODUCTIONThe Coal Receiving Complex of thermal power plant comprised of 250 m long 8 m deep Track Hopper (TH), 12 m deep Wagon Tippler (WT) with provision for addition of another Wagon Tippler. Track center lines of TH and WT were very close. Coal unloading facilities were connected with a network of underground tunnels and Transfer Points (TP) upto Pent House (PH). The facilities were optimized in a compact layout within about 400 m x 120 m area. Initially excavation for TH was started adopting side slope of (1 V : 1.5 H) with 2 m wide berm and dewatering by in-pit sump and pump. When depth of excavation reached about 5-6 m, failure occurred over a long stretch as shown in Figs. 1a - 1b photos. Further work was stopped to develop scheme for carrying out deep excavation and civil works safely."

Jan 1, 2015

The projection of operating costs for mining, processing, and other site operating costs is an exercise which can be fraught with considerable peril. Not only are the physical characteristics of each mineral property unique, but a range of other factors will influence the consultant's approach to compiling cash flow estimates. This paper details some of the techniques used in estimating operating costs for use in order-of-magnitude cost studies and feasibility studies, and describes how to avoid common areas of difficulty. A series of examples relating to open pit gold mining and processing cost estimates illustrate these problems, and various corrective methods are described. The mining and treatment processes, and their associated cost elements, are followed in sequence of operation from on-going ore delineation through to disposal of the product. In addition the problem of assigning management, administration and overhead costs along with taxation allowances is addressed. Of critical importance is the application or possible misapplication of accrual procedures to the cost elements. In many cases such misapplication can introduce more pronounced errors with projects of short duration, such as the typical open pit/C.I.P. gold operation commenced in the last decade. The importance of providing verification of estimates depending upon the standard of the cost study is also investigated, and opinion is provided upon the minimum levels of verification necessary at various stages. Finally, the amalgamation of the various individual cost elements into a coherent whole is reviewed.

Jan 1, 1990

By James A. Barr

Prospecting methods used in Tennessee have gradually improved with the years, as required by depletion of the easily accessible and shallow deposits and the universal trend toward mechanization, and as necessitated by exploring deeper beds, often occurring under limestone and flinty overburden. In the early days it was a very simple matter to dig pits by hand, using a plentiful supply of local farm labor to expose relatively shallow deposits of "brown rock" under shallow clayey overburden that would stand up without timbering. Visual inspection of the exposed phosphate and expert judgment of the "grade" analysis, aided by a "biting" test to reveal presence of unwanted silica, furnished most of the information required. All this might be helped by a few samples sent to the local chemist† who supplemented his income by judicious trading or tanning a few bear skins. The extra curricula activities did not affect the accuracy of the analysis which hold up even under present day standards. Some shot and core drilling was done in Hickman County, mostly for the limestone-like blue Phosphate deposits. The next step was the use of a 4-in. posthole auger, hand operated as described by Guenther, followed by a completely mechanized rig, as described by Pickard. Both these methods are practically adapted to the prospecting of the relatively soft brown rock deposits at moderate depths of clay overburden. For prospecting in areas of deeper overburden, such as are often found in Hickman County, up to 150 or even 200-ft depths, a modified core-drilling method is described by Guenther. Johnston describes a special diamond-drilling technique, developed by TVA, to penetrate flint horizons, which was adopted by the International Minerals in chemical corporation to prospect in Hickman County where deposits had previously been prospected at considerable expense and with difficulty, by small, temporary, hand-dug shafts.

Jan 1, 1948