Search Documents

By N. J. Tannyan

Laboratory bath smelting tests were conducted to determine the feasibility of smelting nickel- copper concentrate directly to a low iron matte in one step. Concentrate, air/oxygen and a silica flux were fed to a matte-slag bath kept in MgO crucibles at 1300°C. Various oxygen enrichments and smelting rates were used to maintain 0.5 to 2 wt"10 iron in the product matte. The slag losses are comparable to those obtained under similar industrial conditions. Due to the highly oxidizing conditions required to produce mattes with low iron contents, it is not recommended to target iron contents below about 2% in the matte. The specific bath smelting rates were equal to or higher than those in various industrial bath smelting processes.

Jan 1, 2003

By Rory S. McLaren

"Cost per ton as it relates to mobile underground vehicle maintenance and repair is invariably astronomical. The reason: the mechanic replaced a ten micron filter with a 250 micron filter because it appeared to be physically identical; the purchasing agent bought ""Brand X's"" filter because it was 25% cheaper- the result, a filter life 30% less; the hydraulic pump was sent for repair at a cost of $2000.00 and failed shortly after installation; pumps are failing because there is no testing equipment available in the workshop.This paper will identify a number of the common pitfalls resulting in high costs, and offer solutions to bring these costs to within acceptable limits.The following key issues will be discussed:A. Genuine parts replacement versus ""Brand X""B. Evaluating outside repair shopsC. The influence of environmental conditions on optional equipmentD. Personnel trainingE. Servicing and testing equipmentIntroductionThere is an old English aphorism, ""Look after the pennies, the pounds will look after themselves"".This paper is aimed at the pennies.Genuine Parts Replacement versus ""Brand X""High interest rates and floundering mineral prices are forcing many equipment owners and operators to purchase ""Brand X"" or ""Pirate"" parts in order to survive. ""Pirate"" part manufacturers invariably offer lucrative discounts which are most appealing to the average purchasing agent whose responsibility it is to save money. Unfortunately, in most cases, there is a tradeoff involved; when the price drops so does the quality, which can adversely affect owning and operating costs. Unless totally obvious, ""original"" or ""pirate"" part metamorphosis requires scrupulous analysis by competent individuals.Hydrostatic transmissions have been used successfully for many year s in various industries. They found their way into mobile underground loaders in the early seventies and have since become very unpopular in mining circles due to their apparent ""inherent unreliability"" and near ""prohibitive"" repair costs. The big benefit of the hydrostatic transmission is compact component packaging which enables the machine to work in very small headings."

Jan 1, 1983

By G. St John Perrott

"The United States Bureau of Mines is cooperating with the State of Utah and the City of Salt Lake in an investigation of methods of abating the smoke nuisance in Salt Lake City. In the course of this work samples of the atmosphere have been collected and analyzed in an attempt to determine the part played by sulphur dioxide or smelter gases in polluting the air at Salt Lake City.A fairly wide-spread opinion exists in Salt Lake City that the smelters contribute appreciably to the smoke nuisance. The gases discharged from the smelter stacks are believed (1) to float over the city in a heavy blanket which prevents the smoke from rising, and (2) to unite with the water vapor in the air to form corrosive fogs injurious to health and property.The first of these theories seems untenable. If the gas did not mix with air it would sink, owing to its heavier specific gravity, and form a blanket an the earth. Actually, the gas diffuses rapidly in air and any part reaching Salt Take must he thoroughly diluted. Perhaps sulphur dioxide in sufficient concentration might aid in fog formation. The more obvious nuisance, however, would be the injury to health and vegetation.The Garfield smelter is 16 miles west of the city, The Murray smelter 8 miles south, and the Midvale smelter 12 miles south. Under normal operating conditions, a relatively small amount of solid matter is discharged from these stacks. The toxic gaseous constituent of the discharge is sulphur dioxide, it is being discharged from the smelters the year round. If they are a factor in the city's smoke problem, the concentration of this gas in the air of the city should be appreciable and should increase toward the smelters, the con centration being highest with a south or a west wind."

May 1, 1920

By J. W. Gunnett

Abstract. The Surface Mining Control and Reclamation Act of 1977 (PL-95-87), Section 522, establishes requirements for state regulatory authorities to designate lands unsuitable for all or certain types of surface coal mining. Any party having an interest in an area that may be affected can petition for it to be designated unsuitable for mining. Section 522 could present major obstacles to the mining industry by typing up an area in an endless round of petitions. The program under development for Kentucky is examined and analyzed as an example for determining the hidden impacts of Section 522.

Jan 1, 1980

Separation of Nickel and Cobalt from Manganese, Magnesium and Calcium by Synergistic Solvent Extraction - From Batch Tests to Pilot Plant Operation The synergistic solvent extraction system consisting of Versatic 10/LIX63/TBP was used for the separation and purification of nickel and cobalt from synthetic laterite leach solution after iron removal. Very encouraging results were obtained for separating nickel and cobalt from manganese, magnesium and calcium. In batch tests, the organic composition of the synergistic system was optimised and very large synergistic shifts for nickel and cobalt were observed. The ?pH50(Mn-Co) and ?pH50(Mn-Ni) values were as large as 1.65 and 2.40, respectively. The extraction and stripping kinetics of nickel and cobalt was fast. Semi continuous extraction tests were conducted with a pH profile of 5.5/6.1/6.5 in three stages at 40¦C. The nickel and cobalt extractions reached 99.9 per cent with only 5 mg/L Ni and <1 mg/L Co left in the raffinate. With two stages of scrubbing, only 2 mg/L Mn and less than 1 mg/L Mg and Ca were left in the scrubbed organic solution. With two stripping stages, the stripping efficiencies of Ni and Co reached over 95 per cent. A fully continuous pilot plant operation was conducted successfully for 280 hours. With an O/A ratio of about 2 and a pH profile of 5.5/5.8/6.0/6.3 for the four stages EX1/EX2/Ex3/EX4, both nickel and cobalt were almost completely extracted. Using a pH profile of 5.4/5.0 for SC1/SC2, the manganese scrubbing efficiency was over 96 per cent. Using three strip stages, over 98 per cent Ni and 99 per cent Co were stripped with only 64 mg/L Ni in the stripped organic solution. The nickel concentration in the loaded strip liquor reached 83 g/L, resulting in a ?Ni of over 28 g/L. The chemical stability of the system was also assessed over 12 weeks under proposed industrial operating conditions. Operation exclusively under strip conditions at 50¦C and 40¦C resulted in LIX63 oxime half lives of 1.1 and 2.1 years, respectively. Operation exclusively under extract conditions at 50¦C and 40¦C resulted in oxime half lives of 0.26 and 0.82 years, respectively. Losses of Versatic 10 were less than four per cent.

Sep 13, 2010

By John D. Sullivan, Alfred P. Towne

"In copper percolation-leaching plants the ore is usually crushed to a maximum size of about three-eighths inch. Ordinarily an ore is crushed as finely as feasible since the rate of extraction of copper is increased with decreasing size of particles owing to the greater surface exposed and. the shorter path required for solutions to come into contact with the minerals to be dissolved. However, greater degree of crushing also increases the amount of fines. When ores are charged into leaching vats the coarse and fine material tend to segregate, resulting in channeling of solutions and leaving the areas where fines predominate only partly leached. An improvement in the method of charging the ore into vats that would minimize the deleterious effects of the segregations of fines would increase the percentage extraction of copper.The Inspiration Consolidated Copper Co.4 recently installed classifiers to remove the primary slimes from the ore, before charging it into the leaching vats. This necessitates a separate agitation treatment for the slimes.Recent publications5 of the bureau have shown the advantages of agglomeration followed by trickle leaching to extract copper from concentrator tailings. It was shown that when equal parts of ore crushed to about 1/4-inch size and concentrator tailings were agglomerated with approximately 10 per cent of moisture, either in the form of water or leaching solution, and the mass was charred into a leaching vat the ore could be treated successfully by open-drainage trickle leaching. Even with 30 or 35 per cent of minus 200-mesh material present the ore could be leached, if it was not flooded with solution.The results obtained in agglomerating ores and slimes suggested the possible advantages to be gained by wetting the crushed ore for standard percolation-leaching plants before charging it into the vats. Wetting the ore whould make the fine material and slime cohere to the larger pieces of ore thus tend to prevent segregation when the ore is charged into the vats. The bureau, at its southwest Experiment Station and in cooperation with the Department of Mining and University of Arizona, Tucson Ariz., therefore made a study to work: out A way in which slimes could be handled in percolation leaching. The study showed that the method of charging ore into the leaching vats governed the distribution the fines and consequently the rate extraction of copper. The results of the study reported in this paper."

Feb 1, 1931

By F. W. Luersson

High carbon, low phosphorus steel can now be made from pig iron containing 0.7 pct P or more, in a commercial sized open hearth furnace. No external heat is required for refining, and steel produced is identical with basic open hearth steel. THE classical Thomas process, which requires liquid pig iron containing over 11/2 pct P, yields a product relatively high in phosphorzs and nitrogen. Unless large quantities of recarburizers are added to the refined steel, the product is low in carbon content. Thus, the Thomas process is not well suited to American raw materials, and its product is often not acceptable according to the standards set by American industry. The shortcomings of the Thomas process have long been recognized; with the advent of low cost oxygen, studies were initiated to develop pneumatic processes which would conceivably overcome the inherent objections to Thomas steelmaking. Several such modified basic pneumatic processes have been tested experimentally in commercial trials during the past decade. Probably the most widely publicized of these developments has been the oxygen converter process as practiced in Austrial,2 and in Canada.8 n this process, oxygen is substituted for air and introduced above the liquid bath in order to increase the heat available to the metallurgical system. This avoids the need for high phosphorus raw materials and gives a product low in nitrogen. In this process, the phosphorus content in the final product depends, to a considerable extent, on the total amount of that element in the burden. The rotary furnace4 which is now in commercial operation at Domnarvet Steelworks, Sweden, is producing low phosphorus steel from iron containing 1.8 to 2 pct P. One or more early slags are removed and by this means high carbon steels of open hearth quality can be produced. At this stage of development there is some question as to the applicability of the rotary process to large heats. Another development has been the use of oxygen in combination with either steam6 or carbon dioxide yn the basic bessemer, thus avoiding the introduction of nitrogen gas into the refining system and giving a product relatively low in nitrogen content. A double slag process has been used in Europe7 in conjunction with a regular Thomas converter, by means of which it is possible to obtain a phosphorus content in the product approaching that obtained in basic open hearth steels. The Turbo-Hearth process:' which uses the side blowing principle so as to produce low nitrogen steel from normal American pig irons, has been developed experimentally in this country. A process fitted to U. S. raw materials All of the preceding processes, with the exception of the rotary furnace, suffer from the common shortcoming that they cannot be adapted to the production of high-carbon, low-phosphorus steels unless large proportions of recarburizers are added. In 1947, a program was initiated by the Inland Steel Company1' to study an oxygen steelmaking process specifically designed to utilize the full range of phosphorus analyses encountered in American pig irons and to give finai products with phosphorus and nitrogen contents comparable to steel produced by the basic open hearth process. Some of the objectives of the proposed process are: 1) the process should be able to accommodate molten pig iron conta;rl;rrg up to 1 pct P., 2) sne process should be subject to close control of carbon analysis, 3) the process should be capable of producing high carbon

Jan 1, 1958

Dado que el Perú es un país que cuenta con una variedad de recursos hidro-eléctricos, es necesario realizar un estimado del valor de los mismos para mejorar las condiciones de su distribución en el país. Por tal motivo, el objetivo del texto es describir las ventajas de funcionamiento de este recurso y el desarrollo de los proyectos hidroeléctricos de la costa, sierra y selva alta. Se conoce que el recurso hidroeléctrico por sí solo no genera riqueza y necesita de la explotación del recurso natural que pueda ser vendido en el mercado. En este sentido, se produce dos beneficios. El primero, refiere que los productos resultantes del binomio energía- recurso industrializable, desarrollan mercados naciones como internacionales, originando una serie de divisas que permiten el desarrollo local en algunos aspectos. El segundo radica en que los proyectos hidroeléctricos de la Costa, permiten mejorar las obras de irrigación de los valles, producción agraria y la industrialización de los recursos minerales. Por tanto, para acceder al mercado internacional, es necesario que los proyectos de industrialización de los recursos, contemplen un planeamiento a partir del desarrollo de las mismas empresas. De forma que el desarrollo de los recursos naturales se realice en condiciones óptimas, satisfaciendo las necesidades básicas de la población.

Jul 20, 1959

By David Bigby

In the UK, it is becoming increasingly necessary to open new longwall mining areas above old, abandoned workings. In such cases, strategic and gate roadways must often be driven and maintained across highly stressed areas and pre-existing and sometimes only recently formed subsidence troughs. Ground control at the edges of the subsidence trough can be particularly problematic, with complex combinations of stress and rock conditions being encountered depending upon the precise position in relation to underlying pillar edges. For economic recovery of these reserves, it is essential that rockbolt support is used wherever possible. It is therefore very important to the industry to develop its understanding of ground conditions and support requirements in these areas. This paper describes; ? the historical background to these problems and a series of documented UK case studies from the last 20 years. ? the experiences at UK Coal?s Riccall colliery, where a number of longwall panels were worked at a depth of around 800m, some 65m above previously worked longwalls. Actual experience is compared with pre-mining expectations and model predictions. ? design considerations and experience to date at UK Coal?s Welbeck and Thoresby collieries, which are embarking upon a series of longwalls in the Deep Soft seam, 30-40m above previously worked longwalls. The paper outlines numerical modelling techniques used to optimise such mine layouts within the complex geological and geometric constraints of a mature coalfield. These involve combinations of 2D and 3D finite difference and 3D boundary element models. It also discuss new modelling approaches which will be investigated in forthcoming EU funded research.

Jan 1, 2007

By F. F. Poland

The purpose of this paper is to describe the recent applications and improvements made in the process and equipment for the recovery of metallic zinc from secondary metals by means of high temperature electric resistor furnace distillation. The process and high temperature furnace, as developed by Revere Copper and Brass Incorporated, Research and Development Department, was described in a previous paper. † Since the publication of that paper the process and equipment have been licensed to others. Consequently its field of application has been expanded, particularly for the treatment of scrap brass, galvanizers dross and scrap zinc. Other applications are being considered, particularly the melting of metallic titanium and special alloys requiring a controlled atmosphere. Consideration is also being given to modification in design that would allow the melting of copper cathodes for the production of oxygen-free and electrolytic tough pitch copper shapes without the necessity of blowing and poling. In the design of a furnace for melting copper cathodes it is intended that the fundamental principle of charging the solid material into a large pool of molten metal through a double door charging vestibule as shown in Fig 3 of the previous paper, † would be adhered to and, in addition, either dehydrated and desulphurized producer gas or commercial nitrogen, that is, approximately 96 pct nitrogen, 2 pct hydrogen 2 pct CO, also dehydrated, would be used to provide a protective atmosphere for the resistors and to flush out more soluble gases from the molten copper. The operation of a small unit producing approximately 1000 lb of copper per hr has shown that the commercial nitrogen will allow the production of tough pitch electrolytic copper when the metal is transferred from the meltdown unit contemplated to a special type induction unit where the oxygen absorption and temperature can be controlled. Standard practice in treating low grade scrap brass has been to oxidize the zinc by blowing air through the molten metal. This operation results in the recovery of approximately two-thirds or less of the zinc content of the brass in the form of an impure zinc oxide having only a fraction of the value of the zinc in metallic form. The balance of the zinc is lost to slag, fume and drosses. Fig 1 shows the revised flow sheet of the process for the treatment of scrap brass. For this application and as shown on the flow sheet a low frequency induction furnace has been substituted for the Wilkins-Poland type as a melting unit. This type of furnace has been found the most suitable for the purpose as will be shown by the following discussion. Serap Brass The melting of refinery scrap brass preparatory to distillation presents a melting problem quite different from the usual melting of brass mill scrap for recasting because refinery scrap is a heterogeneous mixture of alloys each having different melting and boiling points, and coated with a variety of corrosion products and foreign materials. In addition, brass and copper plated pieces of sheet iron, stainless steel, ceramic materials, and others are present that do not melt except at temperatures above the boiling point of the liquid bath. In the previous paper it is noted that difficulty was encountered in the melting of refinery grade scrap brass without excessive loss of zinc by volatilization and that 5 to 10 pct razorite flux was used to alleviate this condition. While this flux was successful in preventing the excessive loss of zinc by volatilization it interposed a low heat conductivity layer between the source of heat and liquid charge and resulted in lowering the melting rate of the furnace. This same problem presents itself in all types of furnaces in which the metal is heated by radiation and conduction from above the charge. It has been found in melting this type material that the melting rate per hour or per square foot of hearth area

Jan 1, 1950

By Manuel Gomez

Bituminous coals having maximum fluidity values in the 40- to 25,400-dial-divisions-per-minute (ddpm) range were carbonized in a continuous, entrained-bed reactor. Carbonization was conducted in an 8-inch diameter, vertical reactor at temperatures from 955° to 1,345° F and at air-to-coal ratios ranging from 4.63 to 16.12 scf/lb of moisture-and ash-free coal charged. Carbonization rates from about 118 to 360 lb/hr, as-carbonized basis, were examined. It was demonstrated that carbonization temperature and air-to-coal ratio must exceed minimum values for continuous operation. Within the operating conditions discussed, highly fluid bituminous coal was carbonized to produce tar and nonagglomerated char. The yield of tar ranged from 21.3 to 38.9 gallons per ton and the char yield ranged from 1,109 to 1,563 pounds per ton, all units expressed on a moisture-and ash-free basis. It was demonstrated that the maximum fluidity and the average size of the coal along with the air-to-coal ratio and the carbonization temperature act together to influence the carbonization product yields and certain properties of the products. Prediction equations were developed from the data for product yields and selected properties of the char, tar, and gas.

Jan 1, 1968

By Jean Bonnemaison

Societe Miniere & Metallurgique de Penarroya Noyelles-Godault works are located in the northern part of France. The complex includes a lead smelter, a zinc smelter, shops for production of manufactured products and all necessary general services. The zinc smelting complex described in this paper was designed in 1959 to replace an old horizontal retort distillation furnace and was first operated in May 1962. It includes: - a sinter plant producing the zinc sinter for the Imperial Smelting furnace : zinc, lead and bulk zinc-lead concentrates are sintered on a Dwight-Lloyd machine with a working area of 80 sq.m. Cadmium sludges are treated by the wet method in a separate plant for recovery of cadmium. Sulphur dioxide contained in gases goes to a gas washing tower and is subsequently made into sulphuric acid in a plant with a capacity of 550 m.t. per day. - a smelting plant where the process developed by Imperial Smelting Processes Ltd. is applied : the blast furnace which was modified in 1967 has an area of 17.5 sq.m. at the tuyeres level and a section of 24 sq.m. at the top of the shaft. It has a theoretical zinc capacity of 100,000 m.t. per annum. Air blast is heated by means of covers up to the theoretical temperature of 950ºC. Zinc produced is either directly cast into slabs for sale as standard 'good ordinary brand' zinc, or sent to a refining plant where the New Jersey process designed to produce 'special high grade' zinc is in application. Mixes of zinc containing various amounts of lead, cadmium or aluminum are prepared to customer specification in a mixing plant.

Jan 1, 1970

By T. W. Camm

"As engineers, we are trained to use logical, rational problem solving to insure our mines operate at maximum efficiency. We tend to use the same technical approach to design safety into all mining systems. This works well for machines, but not so much for the human component. Recent insights in the field of behavioral economics provide useful ideas for addressing the fact that we are driven by emotions more often than by rational thought. Understanding the nonrational aspect of human behavior is an important piece of any safety system design. INTRODUCTION The most common economic model is based on humans making rational decisions; that given the proper information, we will make a logical, rational decision based on what is best for ourselves (Ariely, 2009, p. xviii). In many cases this is an accurate description of how we make decisions. As an engineer, I was trained to apply the precision of mathematics and logic to solve problems. As an engineering professor, I now teach this approach to bright young minds preparing them for a life of professional effectiveness as practicing engineers. That said, we are not only rational. Daniel Kahneman, winner of the Nobel Prize in Economics, describes a model for how we think (Kahneman, 2011). System 1 is the part of our mind that is fast, intuitive, and emotional; while our logical, slower, and deliberative mind is System 2. According to Kahneman’s model, System 1 runs automatically, most of what you think and do originates in System 1. System 2 takes over when things get difficult, including the application of math and logic, and the resolution (or avoidance) of conflict. As engineers, we would typically assume that we operate in System 2 mode most of the time. This is where the model becomes useful, for Kahneman points out two important aspects of the dynamic between the two systems in our mind. First, System 1 has biases, systematic errors that lead to answering questions with an easier answer (rather than a right answer) before System 2 is engaged. Second, we can be blind to the obvious, and also be blind to our blindness. Complicating things further, System 1 cannot be turned off (Kahneman, pp. 24-25)."

Jan 1, 2015

By Curt Swanson, David C. Mathy, Dru R. Nielson, Kent VonAspern

In 1997, Central Contra Costa Sanitary District undertook the design of the Martinez East Side Trunk Sewer Improvements Project. Microtunneling was specified for approximately 1,035 meters (3,400 feet) of 600-mm (24-inch)diameter pipeline to be installed through estuarine soil deposits (San Francisco Bay Mud) and alluvium beneath the congested city streets of downtown Martinez, California. Directional drilling was specified for approximately 275 meters (900feet) of 200-mm (8-inch) diameter pipeline in four separate segments to be drilled through bedrock within narrow utility easements between residential properties. This paper presents a case history for the design and construction of themicrotunneling and directional drilling aspects of the project.

Jan 1, 1999

The concept of isokinetic measurement of strength was originally related by Hislop and Perrine.(1)Characteristics of an isokinetic exertion are constant velocity throughout a predetermined range of motion. Strictly speaking, a means of speed control, and not a load in the usual sense, is applied in isokinetic exertions.(1)However, load and resistance are definitely present in this technique. In this case, the load is a result of the energy absorption process performed by the device to keep the exertion speed constant. The device prevents energy from being dissipated through acceleration in isokinetic exercise. The energy is instead converted into a resistive force, which varies in relation to the efficiency of the skeletal muscle. Since the speed of motion is held constant in isokinetic exercise, the resistance experienced during a contraction is equivalent to the force applied throughout the range of motion. For this reason, the technique of isokinetic exercise has sometimes been referred to as accommodating resistance exercise. This type of exercise allows the muscle to contract at its maximum capability a tall points throughout the range of motion. At the extremes of the range of motion of a joint, the muscle has the least mechanical advantage, and the resistance offered by the machine is correspondingly lower. Similarly, as the muscle reaches its optimal mechanical advantage, the resistance of the machine increases proportionally. It must be understood, however, that while isokinetic devices control the speed of the exertion, this does not assure a constant speed of muscle contraction. The speed of isokinetic contractions is constant during individual exertions; however, it is also possible to compare muscular performance over a wide range of isokinetic velocities. Increasing the isokinetic speed of contraction will place increasing demands on Type II muscle fibers (fast twitch and fast oxidative glycolytic). Workplace Assessment It is clear that isometric strength testing cannot substitute for dynamic strength assessment when examining highly dynamic occupational job demands. As most industrial work tasks contain a significant dynamic component, analysis of isokinetic strength capabilities appears to offer some advantage to isometric testing in this regard. However, it must be recognized that isokinetic devices are not entirely realistic compared with free dynamic lifting in which subjects may use rapid acceleration to gain a weight-lifting advantage.

Jan 1, 1998

By George H. Cook

At first sight this subject seems to belong to pure theoretical geology, but examination will soon show that it has important practical and economic interest to the mining engineer. The conclusion that all the northern portions of our country, as well as of the eastern continent, have, in the later periods of geological history, been covered with a thick bed of ice, is now accepted by geologists. This bed of ice, except in its greater magnitude, was like the modern glaciers of the Alps, and other mountains which extend above the line of perpetual snow. The marks it has left upon the surface show that it was comparatively thin on its southern edge, but that its thickness was much greater a little further north, and that it was several thousand feet thick at its kenviest parts. This variation of its surface would give it a descending slope towards the south, and cause the mass of ice, like a semifluid substance, to move in that direction,

Jan 1, 1879

By Dale E. Wittmer

Nonoxide ceramic materials could substitute for high-temperature alloy steels containing imported critical and strategic materials such as cobalt, chromium, and nickel if their high-temperature properties can be improved. An important result of this substitution would be a reduction of the Nation&apos;s need for imports of critical and strategic materials. In this Bureau of Mines investigation, the primary objective was to produce high-purity u1trafine (particles <5 ~m equivalent spherical diameter (ESD)) alpha-silicon carbide (a-SiC) powders with improved high-temperature properties using the Bureau&apos;s patented turbo-milling process. A secondary objective was to determine the feasibility of using polymer mill construction materials as a means of eliminating metal contamination from the turbomill. U1trafine a-SiC powders with BET (Brunauer-Emmett-Te11er) surface areas from 30 to 35 m2/g (~0.06 ~m particle ESD) were produced in an all-polymer turbomi11. These high-purity powders (with I-pct Band I-pct C additions) hot-pressed to greater than 99 pct of their optimal density and exhibited properties commensurate with those of commercially available a-SiC. The most promising of the construction materials tested for the major wear surfaces of the turbomi11 was u1trahigh-mo1ecu1ar-weight (UHMW) polyethylene, a polymer thermoplastic.

Jan 1, 1984

By Valerio Violo, Antonio Raschillà, Livia Cicinelli

"The Cityringen project foresees the construction of a new circular metro line in and around the city center of Copenhagen. Both drives, the north and the south one, required the TBMs to be equipped in order to cope with contaminated water table and soil. The north drive mined in water contaminated with chlorinated compounds, including chloroform and vinyl chloride, while the south TBMs excavated in a highly benzene contaminated area, becoming the first TBMs to complete such a challenge. Despite the pollution and the stricter operative procedures, the production has been extremely successful with record up to 520 m in one month and 32 m in one day. 1 INTRODUCTION The Cityringen is an extension of the existing metro line. The 15 km long twin tunnels will form a new circular line with 21 new stations (17 + 4 crossovers). When finished it will interchange with the existing metro, rail and bus infrastructure at key locations around town, taking 90% of Copenhagen citizen at less the 600m from a metro station (Figure 1). The Contract has been awarded in April 2011 to the Copenhagen Metro Team (CMT), a joint venture between the Italian companies Salini Impregilo, Tecnimont and Seli SpA. Tunnels are being excavated with 4 Seli-Kawasaki EPB TBMs, two of which manufactured in Denmark by Seli Tunneling Denmark ApS, which is also operating them. At the moment this article is written 50% of the tunnels have been completed and over 40% handed over for the electromechanical works. Seli Tunnelling Denmark is a Danish company constituted in 2012 as a subsidiary of Seli SpA for this project and subsequently acquired by the Salini Impregilo Group in 2015."

Jan 1, 2016

By M. Medraj, M. A. Arafin, D. P. Turner, P. Bocher

In this study, the kinetics of isothermal solidification during TLP bonding of Inconel 625 and 718 superalloys with nickel based multi-component filler alloy BNi-2 have been studied through a combination of direct experimentation and mathematical modeling in order to determine the effect of process variables and, thus, to optimize the process. The predicted isothermal solidification completion times from the boron diffusion model and migrating solid/liquid interface model were in good agreement with the experimentally determined values and, they were found to be significantly less than those of other nickel superalloys with different nickel based filler alloys. Further, significant reduction of holding time was observed with increasing bonding temperature and with decreasing joint gap. No significant grain growth in the base metals has been observed in the temperature range being investigated (1325 - 1394K).

Jan 1, 2006

By J. R. Gordon

I-Introduction The possibility of adapting low-temperature reduction methods to the treatment of iron ores has been suggested on numerous occasions. Papers published on the subject include, notably, Bulletin 270 of the United States Bureau of Mines on The Production of Sponge Iron, the Symposium of the American Electrochemical Society (1927) on The Gaseous Reduction of Ores and Other Metallic Compounds, and Les Procédés Actuels de Traitement Direct du Minerai de Fer, by A. Mayer (Revue de l&apos;Industrie Minerale, Nov. 15th, 1932) (1). The present paper contains the results of an investigation of the reducibility of some Ontario ores. The concentration of these ores and of the products of reduction has also been investigated.

Jan 1, 1933