Search Documents

By Du Sichen, K. Mukai, S. Seetharaman

Viscosities of slags constitute an important physical property needed for an understanding of the mass transfer phenomena in metallurgical processes. Viscosity is also the key that leads to a better understanding of the structure of slags. It is well known that the viscosities of silicate slags decrease with the addition of basic oxides due to the breaking of the silicate network. The measurements of slag viscosities often pose experimental challenges, especially to the choice of materials. The keynote lecture takes up the experimental problems and the various techniques adopted. Dynamic viscosity measurement, as a powerful tool towards an understanding of the kinetics of some high temperature reactions, is brought out. A number of semi-empirical models have been developed to estimate the slag viscosities in the case of multi component slags. A critical survey of these models is presented in the lecture. Earlier models by Riboud et al., Urbain et al. and Mills et al. have been developed further into a new generation of models. Some of the current important models are (1) Model by Iida et al. (2)CSIRO model (3) Pyro research Model (4) Model by Tanaka et al. (5) Model approach by Reddy et al. and (6) KTH-model. The predictions and capabilities of the various models are compared. Estimations of viscosities from thermodynamic data and prediction of liquidus temperatures from viscosities are presented. The concept of surface viscosities with reference to slags and viscosities of two-phase mixtures are also taken up in the presentation.

Jan 1, 2004

By Henry A. Stiff, J. P. Hammond, A. B. Westerman, H. C. 195-000-000-014 Cross, and Lawrence E. Davis

The phases in Cr-Fe-Mo alloys have been investigated with homo-genization, aging temperature, composition range, and alloy addition as variables. Metallography, three X-ray methods, and hardness were used as methods of study. The behavior of s, M23,C8, and Z phase are reported for cornpasition range 60 pct Cr-15 to 25 pct Fe-15 to 25 pct Mo-<0.005 to 0.36 pct C with aging at 1400º to 2000°F. With 2 pct Ti, Tic and TiC-TiC are formed; with nitrogen Cr2N. THE recently developed class of chromium-base heat-resistant alloys shows appreciably higher strength than commercially used high temperature alloys. However, further developmental work is required to impart needed shock resistance and some degree of room-temperature ductility to these alloys. Extensive exploratory work on chromium-base alloys was begun in a program initiated by the War Metallurgy Committee of the National Defense Research Council at the Climax Molybdenum Co. in the early part of 1942.&apos; Alloys were sought for gas-turbine blades for use at 1600°F. A minimum of 5 pct elongation in the stress-rupture test was a requirement. From the Climax work, ternary alloys of chromium, iron, and molybdenum appeared to show the greatest promise as materials for gas-turbine blades. The composition line in the ternary diagram joining the 60 pct Cr-15 pct Fe-25 pct Mo and 60 pct Cr-25 pct Fe-15 pct Mo alloys was indicated as representing the most useful combination of strength and ductility.&apos; Strength increased while ductility decreased as molybdenum was raised in this composition range.&apos; The 60 pct Cr-15 pct Fe-25 pct Mo type alloy was thought to have the most suitable properties for gas-turbine blades.&apos; Concurrent with the study reported here, other investigations were being made on Cr-Fe-Mo alloys. The liquidus temperatures on a series of low carbon, ternary alloys were being determined, and isothermal sections drawn at 2370°, 2010°, and 1650°F (1300°, 1100°, and 900°C).2 Also, various methods of preparation and some mechanical and physical properties of chromium-base alloys, particularly the 60 pct Cr-15 pct Fe-25 pct Mo type, were being investigated., At the inception of the present program, only a limited study had been made of etchants for developing the microstructures of chromium-base alloys; X-ray analysis of the microconstituents had not been made. A review of the literature revealed that no phase-diagram work had been reported on the Cr-Fe-Mo system. Scope of Work The work on chromium-base alloys includes the following: 1—The development of etching methods for differentiating between the microconstituents; 2—The identification of microconstituents by X-ray diffraction methods; and 3—A comprehensive metallographic and hardness study after various heat treatments. The phases were studied by three standard X-ray techniques: 1—The block-sample focusing-camera method; 2—The powder-diffraction method on elec-trolytically separated residues; and 3—The powder-diffraction method on cold-worked aggregate samples. The results by the first two methods were correlated with the metallographic data. The third method was used largely to study conditions approaching equilibrium, since cold working prior to heat treating accelerated precipitation. Seven types of alloys were investigated: 50 pct Cr-50 pct Fe, 40 pct Cr-40 pct Fe-20 pct Mo, 55 pct

Jan 1, 1953

By L. A. Bromley, A. W. Petersen

The van Arkel-deBoer method for producing ductile titanium by thermal decomposition of Til, vapor and deposition on an electrically heated filament is modified by film boiling Til liquid on a heated filament, resulting in similar titanium deposition on the filament and liberation of gaseous iodine. The deposition rate is higher and the energy requirement smaller than in the van Arkel process. Many problems must be solved before the process is commercially feasible. TITANIUM of 99.9 pct purity, called ductile titanium, has been produced by a modification of the van Arkel-deBoer&apos; method. In the van Arkel-deBoer method, an electrically heated wire is suspended from two electrodes, which are placed in a container holding TiI, vapor at a low&apos; vapor pressure (usually <5 mm Hg). The vapor diffuses to the hot wire, usually maintained at 1100" to 1600°C,&apos; and decomposes according to the reaction liberating gaseous atomic iodine and depositing solid crystalline titanium on the wire. Estimations based on the data of Runnalls and Pidgeon,&apos; indicate that the rate-control ling step is the diffusion of atomic iodine away from the wire. There appears to be nearly thermodynamic equilibrium at the wire with TiI, and iodine as the main gaseous species. TiI, is almost certainly an important gaseous species in the cooler regions.&apos; The liberated iodine diffuses to a heated source of crude titanium and reacts to form more TiI, vapor, which again diffuses to the hot wire and completes the cyclic process. The foregoing process may be modified by suspending the hot wire in liquid TiI,, instead of the vapor, and obtaining film boiling. This type of boiling is characterized by the formation of a continuous film of vapor over the wire surface. Since only vapor contacts the wire sul.face, the temperature of this surface may be raised as high as desirable, within the limit of mechanical strength requirements for the wire. By properly adjusting the input voltage. the temperature of the wire may be maintained above U0C"C; and by evacuating the vessel holding the liquid TiI, and maintaining a suitable condenser temperature, the vapor pressure of TiI, may be held low. Thus, the conditions of operation of the van Arkel-deBoer method may be approximated with film boiling; and hence, it is postulated that ductile titanium may be produced by this method. Preparation of Til, There are many methods available for the preparation of TiI,; that used in this research was prepared by the direct reaction of titanium sponge in controlled amounts with liquid iodine. Although no difficulty was encountered with this reaction, it has since been pointed out that this method is sometimes dangerous and should be used with caution. The resulting TiI, was purified by distillation. First Film Boiling Experiments Apparatus: The apparatus shown in Fig. 1 was used for film boiling TiI, on short wire filaments. The current to the filament was supplied through a bank of three 5 kva transformers connected in parallel. The current was controlled by adjusting the voltage over a 0 to 67.5 v range with a 7 kva variable transformer on the low voltage side of the bank of transformers. The current and voltage were measured by Weston meters. The sealed-in-glass tungsten electrodes were hard-soldered to the filament for the film boiling of TiI,. The bottom part of the reactor, containing TiI,, was wrapped with ni-chrome heating wires to maintain the TiI, in the liquid state. An ice or liquid nitrogen trap, for solidifying I, vapor and any TiI, not condensed, was attached to the low pressure side of the air-cooled condenser. A Megavac vacuum pump was used. Procedure: A 0.010 in. diam tungsten filament was hard-soldered to the tungsten electrodes. TiI, was melted (mp 156°C) and poured into the reactor chamber; the top of the reactor chamber, containing the electrodes, was replaced. Freezing of the TiI, was prevented by controlling the current to the ni-chrome wires wrapped around the reactor with a 1 kva variable transformer. The mechanical vacuum pump was started and the system evacuated to about 2 mm Hg TiI, vapor pressure. The current to the filament was turned on and the impressed voltage slowly increased with the variable transformer. A sudden drop in current at nearly constant im-

Jan 1, 1957

By David Atkin

This paper presents methods and results of environmental planning conducted for a proposed coal and iron ore transshipment terminal which would be located on reclaimed land west of Lisbon, Portugal. Oceanographic, navigational, marine, structural, material handling, and financial studies of the terminal were conducted along with the environmental analyses. However, because of the proximity of the terminal to heavily used recreational resources, residential areas, and biologically valuable habitat, anticipating and reducing the environmental effects of the terminal to minimum levels was a very important part of the overall project. The results of the study indicate that even the impacts associated with worst-case conditions would be acceptable because of appropriate pollution control measures and planning.

Jan 1, 1983

By Larry Gsellman

This report presents the results of a benefit/cost analysis of the Bureau of Mines&apos; Coal Extraction RCD Program for the period FY 1977 through FY 1982. The analysis is an update of the analysis performed on the Coal Extraction R&D Program for EY 1975 - FY 1980 and presented in a MITRE report, MTR-7225, published in May 1975. Major changes included: new production scenarios and an update of R&D cost estimates.

Jan 1, 1977

By Tell Ertl

THE Piceance Creek Basin in northwestern Colorado is believed to contain the richest large deposit of oil shale in North America. The major portion, about 1650 sq miles, is bounded by the White River on the north, the Grand Hogback, which runs from Meeker to Rifle, on the east, the Colorado River to the south, and the drainage basin of Salt and Douglas Creeks on the west. The Basin is a plateau 7000 to 9000 ft high, composed of 3000 ft of the Green River series of Eocene age and surrounded by a steep escarpment of 1000 to 3000 ft. From the escarpment the beds dip gently toward the center. Although oil shale is found in all members of the Green River series, the rich thick beds are found chiefly in the Parachute Creek member. This is normally capped by 100 to 200 ft of the Evacuation Creek, the youngest member of the Green River series. Actually the Piceance Creek Basin oil shale is not a shale, nor does it contain oil. It is magnesium marlstone holding solid organic matter capable of being broken down by heat into gases, some of which can be condensed into oil. The marlstone is resilient nonporous rock, difficult to sample by pick or hammer and moil. Many companies and individuals prospected the Colorado oil shale shortly after the first World War,&apos; see Fig. 1, but because of the discovery of large quantities of petroleum in the late 1920&apos;s in Cali- fornia, Oklahoma, and East Texas, interest in oil shale development waned and did not revive until World War 11. In 1944 the writer, employed by the Bureau of Mines, prospected the high grade oil shale in numerous places along the southern outcrop of the Piceance Creek Basin. Several channel samples about 100 ft in length were cut, see Fig. 2. An eight-man crew needed a week to cut a satisfactory channel 80 ft long in the cliff face. The Phillips Petroleum Co., the Union Oil Co. of California and others also prospected the oil shale outcrop. In 1945 the Bureau of Mines initiated a core drilling program for the purpose of obtaining accurate samples from the Piceance Creek Basin. The U. S. Geological Survey set up a program for the geological study of the Basin that is still going on." Until the end of 1951 a total of 31 holes was drilled for core with diamond drills, and, in addition, cuttings through the oil shale have been obtained from 4 gas wells drilled by standard rotary oil well rigs. The Bureau of Mines drilled 12 of the holes, the Union Oil Company of California 8, the Standard Oil Company of California 6, the Sun Oil Company 3,

Jan 1, 1953

By J. G. Thompson

Determinations of the hydrogen content of irons and steels invariably are subject to two serious difficulties: (I) the determination of amounts of 0.001 per cent or less of any constituent requires an analytical procedure of unusual precision and accuracy, and (2) the hydrogen content of many samples is dccidedly not stable; i.e., there is no assurance that the content at the time the analysis is made is the same as it was when the sample was taken or at some previous time in the history of the piece. In respect to both the precision and speed of the determination, the vacuum-extraction procedure for the determination of hydrogen possesses advantages over the vacuum-fusion procedure, which has been the recognized standard for the detcrmination of other gaseous elements in sted-— oxygen and nitrogen for example. The basic facts upon which the vacuum-extraction procedure is based—i.e., the evolution of gas from solid steel when it is heated in vacuum, and the fact that the evolved gas is rich in hydrogen—were observed by Graham1 many years ago. Subsequent investigations have shown that hydrogen exists in steel chiefly as interstitial solid solution (i.e., in atomic dispersion) and perhaps to some extent as hydridcs that are unstable and decompose to form atomic hydrogen. In either case practically all of the hydrogen in steel at elevated temperatures exists in the atomic condition and consequently is able to diffuse readily through the metal. In contrast to this, other gaseous elements, such as oxygen and nitrogen, normally are present in steel chiefly in the form of relatively stable compounds such as oxides or silicates and nitrates; i.e., the oxygen and nitrogen atoms are fixed in stable combinations and are not free to migrate. The only oxygen or nitrogen that can diffuse in steel is the small amount in solution (atomically dispersed) and the rate of diffusion of these atoms is much less than that of hydrogen because of their greater atomic volume and lower mobility. Consequently, it is possible to extract most or all of the hydrogen from solid steel in a reasonable time at moderately elevated temperatures, but the procedure is not applicable to the determination of oxygen or nitrogen. It is only within the last decade that these observations have been developed into an analytical procedure for the determination of hydrogen. Apparatus and Procedure The apparatus used at the National Bureau of Standards,6 for the determination of hydrogen by the vacuum-extraction procedure, is shown schematically in Fig. I. The specimen, freshly cleaned and dried,* is suspended on a fine wire within the quartz furnace tube that is connected to the reservoir system and analytical train.

Jan 1, 1945

By Tell Ertl

THE Piceance Creek Basin in northwestern Colorado is believed to contain the richest large deposit of oil shale in North America. The major portion, about 1650 sq miles, is bounded by the White River on the north, the Grand Hogback, which runs from Meeker to Rifle, on the east, the Colorado River to the south, and the drainage basin of Salt and Douglas Creeks on the west. The Basin is a plateau 7000 to 9000 ft high, composed of 3000 ft of the Green River series of Eocene age and surrounded by a steep escarpment of 1000 to 3000 ft. From the escarpment the beds dip gently toward the center. Although oil shale is found in all members of the Green River series, the rich thick beds are found chiefly in the Parachute Creek member. This is normally capped by 100 to 200 ft of the Evacuation Creek, the youngest member of the Green River series. Actually the Piceance Creek Basin oil shale is not a shale, nor does it contain oil. It is magnesium marlstone holding solid organic matter capable of being broken down by heat into gases, some of which can be condensed into oil. The marlstone is resilient nonporous rock, difficult to sample by pick or hammer and moil. Many companies and individuals prospected the Colorado oil shale shortly after the first World War,&apos; see Fig. 1, but because of the discovery of large quantities of petroleum in the late 1920&apos;s in Cali- fornia, Oklahoma, and East Texas, interest in oil shale development waned and did not revive until World War 11. In 1944 the writer, employed by the Bureau of Mines, prospected the high grade oil shale in numerous places along the southern outcrop of the Piceance Creek Basin. Several channel samples about 100 ft in length were cut, see Fig. 2. An eight-man crew needed a week to cut a satisfactory channel 80 ft long in the cliff face. The Phillips Petroleum Co., the Union Oil Co. of California and others also prospected the oil shale outcrop. In 1945 the Bureau of Mines initiated a core drilling program for the purpose of obtaining accurate samples from the Piceance Creek Basin. The U. S. Geological Survey set up a program for the geological study of the Basin that is still going on." Until the end of 1951 a total of 31 holes was drilled for core with diamond drills, and, in addition, cuttings through the oil shale have been obtained from 4 gas wells drilled by standard rotary oil well rigs. The Bureau of Mines drilled 12 of the holes, the Union Oil Company of California 8, the Standard Oil Company of California 6, the Sun Oil Company 3,

Jan 1, 1953

By J. P. Walker

"INTRODUCTION Sponge iron has been made commercially since 1912 at a Swedish ceramic plant; and the product, known as Swedish disk-type nagger sponge iron, has an excellent reputation as a superior furnace feed wherever high-grade steels are made.The general procedure for making brickyard sponge iron was described frequent in Swedish technical journals before 1932 and at that time consisted in filling clay refractory containers, called saggers, with iron ore plus the necessary quantity of solid reducing agent and then firing in an ordinary ceramic kiln. Two types of sponge iron were made in this way: (1) An inferior, high-sulfur product obtained by mixing the ore and solid reducing agent; and (2) a high-grade, low-sulfur product made by filling the sagger with alternete layers of unmixed ore and reducer, yielding sintered disks of metallic iron particles.Swedish disk-type sponge iron of interest to the steel industry because it has a very low sulfur content, even when made by the use of low-grade, high-sulfur coals for reducing and firing. The Swedish product also contains little siliceous gangue residue and is almost phos¬phorus-free. To those features must be added the high metallic-iron content -90 to 96 percent - and freedom from even small amounts of the metals that are undesirable in steel making.The details essential for successful operation of this procedure are not known, especially as regards improvements said to have been made since 19;2. The Bureau of Mines therefore decided to determine some of these missing details, and this report records the results of the first set of experiments on the manufacture of brickyard or sagger sponge iron."

Sep 1, 1945

By S. S. Yu

In this paper, the producing process of using V2O3 as raw material to obtain vanadium nitride was analyzed through the means of thermodynamic. The analysis shows that conversion follows the principle of reduction step by step in the conversion process of V2O3. The temperature of the reaction system has prominent influence on the nitrogen content of products, and the reaction is very sensitive to temperature. As raising temperature, the fine grain structure of the nitrides is more evident, and the grain size of nitrides increases. At 1703K, the nitrogen content of the products tended to be constant after soaking over 3 hours.

Jan 1, 2014

By Wenbin Liu

A novel route for rapid synthesis of ultrafine WC-Co cemented carbides with homogeneous binder phase distribution is reported. The composite powder is produced by in situ reduction-carbonization reactions by using WO2.9, Co3O4 and carbon black as raw powders. The reaction equilibrium and phase stability are studied by thermodynamic calculations. The WC-Co composite powder is condensed by spark plasma sintering (SPS) to obtain the cemented carbides bulk. The sintering temperature is lower than that in the conventional sintering methods by 1500C, while the sintering time is remarkably reduced by 3-5 times. The high performances of the hardness and the fracture toughness are obtained. The experimental results confirm that the present processing scheme of in situ reduction-carbonization reactions and subsequent SPS sintering is an efficient way to prepare WC-Co cemented carbides, and is apparently superior to the conventional long-period techniques of preparing composite powder and cemented carbides bulk.

Jan 1, 2008

By Yijia Dong, Mingjun Rao, Pengxu Cao, Jun Luo, Guanghui Li, Zhiwei Peng

Coal fly ash (CFA), as a by-product generated from coal fired power stations, is widely used for autoclaved concrete block production. It has been found that the generation of tobermorite is great benefit to the block strength during autoclaving. In this study, the tobermorite fibers synthesized from CFA and lime via the hydrothermal process are used as the revulsive to promote the mechanic strength of the concrete blocks. The results show that tobermorite fibers with 0.01–0.5 lm in diameter and 1–3 lm in length are obtained at 200 °C for 0.2 h. As the addition of prepared tobermorite fibers increases from 0 wt% to 2.0 wt%, the compression strength of concrete block increases from 24.6 to 40.5 MPa, and the compression strength of aerated concrete block produced under the optimized conditions can reach above 7.5 MPa.

Mar 1, 2018

By Kenneth P. V. Lei

The Bureau of Mines investigated a silver-catalyzed oxidative procedure for leaching an arsenical copper sulfide concentrate containing 10 pct As and 32 pct Cu_ Currently, there are no environmentally safe means to treat arsenical copper concentrates in the United States. Leaching was conducted in a 2-L autoclave reactor. The effects of catalyst concentration, O2 pressure, temperature, and H2S04, Cu, As, and Fe concentrations in the leaching solution on extractions of metals from the concentrate were determined. The best leaching conditions for extracting 95 pet eu and As and less than 21 pct Fe were 260 g/L concentrate, 0.007 mol/L (1.0 g/L) AgCI, 3.0 mol/L (294 gIL) H2S04, 1000 C, 60 psig 02, and 6 h. Copper as CuS04-5H20 was recovered by crystallization from the pregnant solution. Arsenic, as AS203, was recovered from the copper mother liquor by solvent extraction, with tributyl phosphate, S02 reduction of As5+ to As3+ in the strip solution, and crystallization of the As3+. The silver catalyst was recovered by contacting the leached residue with a brine solution. A conceptual scheme is proposed for treating arsenical copper sulfide concentrates.

Jan 1, 1987

By N. A. Gokcen, J. Chipman

A revised treatment of the authors&apos; published data eliminates the complex relation previously proposed between concentration of silicon and activity coefficient of oxygen in liquid iron. Revised values of the thermodynamic properties of the liquid solution are presented. IN a recent experimental study of the reaction SiO2 (s) = Si+ 2O; Kf, = [% Si] [% O]² [1] the authors&apos; found a substantially constant equilibrium product in liquid iron at 1600°C of 2.8x10-5 They also reported extensive data on the reactions: SiO2 (s) + 2H2 (8) = Si- + 2H2O (g); K&apos;2= [% Si] (H2O/H2 [2] and H, (g) + 0 = H2O (g); K&apos;3 =( H2 O [31 (H2) [%O] From the results on reaction 3 and earlier data of Dastur² on this same reaction in the absence of silicon, they determined the activity coefficient of oxygen, f0, on the basis of the definition K3 = (H2O)/ (H2)f0 [% 0] where K, is the equilibrium constant and f0, is taken as unity in the pure Fe-0 system. Similarly values of fsi were deduced from results on reaction 2. In a more recent study" of analogous reactions in the system Fe-A1-0, it was found impossible to reconcile the results on reaction 3 with Dastur&apos;s data; accordingly the latter were ignored and the equilibrium results were extrapolated to find a value of K, at zero concentration of aluminum. This procedure failed to locate the cause of the discrepancy but it did yield reasonable values of activity coefficients. It also avoided introduction of the complex empirical relation between the oxygen activity coefficient and the concentration of the added element. The same type of discrepancy exists for system Fe-Si-0.&apos; In the earlier paper an attempt was made to fit both sets of data by a single curved line (Fig. 6 of ref. l), the form of which is contrary to the theoretical requirement of a finite slope at infinite dilution. In the light of experience on the Fe-A1-0 system the discrepancy must be recognized as one which can be resolved only by more refined measurements. Accordingly Figs. 6 and 10 are retracted. It is pointed out also that until the discrepancy is resolved Figs. 7, 8, and 11 are subject to some uncertainty. Qualitatively the following conclusions still appear valid: 1—The activity coefficient of oxygen is reduced by addition of silicon. 2—In dilute solutions the activity coefficient of silicon increases with its concentration. 3—With respect to equilibrium in reaction 1, the above effects are approximately compensating. The discussion of K&apos;1 in the previous paper requires no revision. It was pointed out that the constancy of the product [% Si] [% 0]² ndicated a compensating effect of the activity coefficients of silicon and oxygen. Therefore, as a very good approximation, K1 = K&apos;1 and the following average values are suggested both for K, and K&apos;, at the temperatures 1550°, 1600°, and 1650", respectively, 1.0x10-", 2.8~10-" and 5.5 ~lo-&apos;. Revision of the thermodynamic treatment is necessitated by the recent appearance of new data, based on a combination of combustion and solution calorimetry,&apos; which yields for the heat of formation of low-cristobalite from the elements, the value —209,330 ±250 cal per mol at 25°C. This is about 4000 cal larger than the value previously accepted. The new value for cristobalite is used, together with Kelley&apos;s tables of high-temperature heat contents" and entropies and with Korber and Oelsen&apos;s&apos; heat of fusion of silicon to obtain the following equation for the standard free energy of cristobalite in the temperature range 1700" to 2000°K: Si (1) + 02 (g) = Si02 (crist.); ?F° = -217,700 + 47.OT [4] The free energy of solution of 0, in liquid iron is:8 O2 (g) = 20 (in Fe); AF° = -55,860 - 1.14T [5] and these two equations are combined to give: Si (1) + 20 = SiO, (crist.); AF° = -161,840 + 48.14T [6] ?F°1873 = -71,700 cal. From the experimental value of K, = 2.8x10-5, Si + 20 = SiO2 (crist.); ?F°1873 = -39,000 cal. [7] The combination of Eqs. 6 and 7 yields the free energy change when liquid silicon dissolves in iron to form the dilute solution of unit activity (1 pct). Si (1) = Si; ?F°1873 = -32,700 cal. [8] The heat effect in this process according to Korber and Oelsen&apos; is an evolution of 28,500 cal per gram

Jan 1, 1954

By E. M. Cox, A. S. Skapski, N. H. Nachtrieb, M. C. Bachelder

As a result of using copper-containing scrap in the steelmaking process, the copper content of steels has been steadily increasing for years. Consequently the possible role copper may play in the steelmaking process and in the finished product begins to attract the metallurgists&apos; attention. Some time ago one of the present authors forwarded the idea—based on the results of the analysis of nonmetallic inclusions extracted electrolytically from steels—that sulphur in plain carbon steels is distributed mainly between copper and manganese, the amount of iron sulphide being very small; and that, consequently, the problem of copper and that of sulphur in steel cannot be treated separately.&apos; At the time of the publication of the quoted paper little was known about the relative affinities of copper and manganese for sulphur at high temperatures except that at moderate temperatures (below 1000°C) the affinity of manganese for sulphur is much greater. To gather more experimental data on this subject, the present authors undertook the investigation of the equilibrium constants of the reactions: 2Mn(8 or 1) + S2(g) = 2MnS(s) 4Cu(s or 1) + S2(g) = 2Cu2S (S or I)* 2Fe(s) + S2(g) = 2FeS (s or 1) over a range of temperatures wide enough to establish the dependence of these equilibrium constants on temperature. From the equilibrium constants (K = l/Ps2) the free energy of formation (affinity) can be calculated from F° = -RTln 1/PSt (1) where the standard conditions chosen are: 1 atm of sulphur pressure and the activities of condensed components equal one. The decomposition pressure, Ps2, of sulphur over the respective sulphides is too small to be measured directly, but there is a way of eliminating this difficulty by measuring the equilibrium constant of the reaction between the sulphide and hydrogen. From the latter and from the equilibrium constant of the thermal dissociation of H2S we then calculate Ps2 for the respective sulphide. 2Mn + 2H2S = 2MnS + 2H, 2H2 + S2 = 2H2S_________ 2Mn + S2 = 2MnS The numerical values of the equilibrium constant of the thermal dissociation of H2S at different temperatures were taken from Kelley&apos;s paper, "The Thermodynamic Properties of Sulfur and its Inorganic Compounds."² In previous experimental work published by Jellinek and Zakowski3 and by Britzke and Kapustinsky4 the equilibrium constants of the reactions Metal sulphide + H2 = H2S + metal were determined by passing hydrogen, at different rates of flow, over the sulphide, analyzing the resulting H2S + H2 mixture and then extrapolating the H2S/H2 ratio (which is a function of the rate of flow) to the zero speed of flow, a method necessarily involving considerable uncertainty. In the present work the equilibrium ratio was actually measured instead of being extrapolated. The apparatus is shown in Fig 1. Experimental Procedure The sulphides were prepared by the following methods: FeS Powdered iron which had been reduced with hydrogen (ferrum reduc-tum) was mixed in stoichiometric ratio with sublimed sulphur and carefully ground. The mixture was put into an alundum crucible, covered with pure sulphur, and the reaction started by touching the mixture with a glowing iron rod. After the reaction was completed the product (still containing some metallic iron) was again ground with sulphur, put into a Rose crucible, covered with sulphur, and heated in a strong current of pure hydrogen. Analysis of the final product showed 62.46 pct Fe and 36.59 pct S. Theoretical for FeS: 63.53 pct Fe and 36.47 pct S. MnS Manganese sulphide (precipitated and carefully washed with distilled water containing H2S) was dried in a Rose crucible in an atmosphere of H2S and heated in a current of hydrogen for 2 hr at red heat. The product was then ground and ignited for several hours at 1000°C in a current of hydrogen sulphide. Analysis showed 64.53 pct Mn and 36.63 pct S. Theoretical: 63.15 pct Mn and 36.85 pct S. Some MnS samples were prepared from metallic manganese and sublimed sulphur by mixing and grinding them and then heating in a current of hydrogen sulphide in an alundum tube.

Jan 1, 1950

By W. G. Lidman, H. J. Hamjian

&apos; I HE fabrication of many materials from powders involves a sintering process. A mass of powder will sinter because of the excess free energy over the same mass in the densified state caused by the higher total surface area of the powder. An understanding of the kinetics and mechanism of sintering should assist in improving the properties of such materials. The present investigation conducted at the NACA Lewis laboratory deals with the sintering of chromium carbide. Dry sintering (sintering at a temperature below the melting point) was divided into two stages by Shaler:&apos; the first stage, during which the particles preserve much of their original shape and the voids are interconnected, and the second stage, during which densification occurs and the pores are isolated. The mechanism of forming interfaces between particles, or welding together of particles, has been investigated by Kuczynski2 and may be described by any one or a combination of the following mechanisms: viscous flow, evaporation and condensation, volume diffusion, or surface diffusion. The mechanism by which pores are closed or eliminated (densification) during sintering, is of interest. Grain growth observed during sintering may be attributed to the variation in the surface energies of individual grains, causing some grains to grow at the expense of others. Grain boundary migration occurs presumably by a diffusion process, therefore the rate of grain growth would be expected to increase exponentially with increasing time and temperature. Thus, for practical sintering times of less than 1 hr, a certain minimum temperature may exist at which major structural and property changes will occur. Densification and kinetics of grain growth during sintering under pressure of chromium carbide were investigated to provide additional information which will aid in describing more accurately the sintering process and the mechanisms involved. This material was selected for this study because of the current interest in high strength, oxidation resistant refractory materials, such as carbides, which are sintered to produce solid, dense materials from powders. Sintering under pressure is a process where the heat and pressure are applied to the compact simultaneously, specimens for this work were prepared by sintering under pressure at different temperatures and for various time periods. Experimental Procedure Preparation of Specimens: Chemical analysis of the commercial chromium carbide used in this investigation was as follows: Cr 86.19 pct, C 12.14 pct, and Fe 0.2 pct. X-ray diffraction powder patterns gave characteristic diffraction lines of Cr3C2 crystal structure. Powder particle size was determined microscopically and the average initial particle size was 6 microns with 85 pct between 2 and 10 microns. Specimens sintered under pressure were formed in graphite dies3 heated by induction. Sintering temperatures were measured with an optical pyrometer by sighting into a 3/8-in. hole drilled 1 in. deep at the midsection of the graphite die. A load of approximately 1 ton per sq in. was applied to the powder. The die assembly was heated in 20 min to the highest temperature (2500°F&apos;) at which no increase in grain size could be observed, and less than 2.5 min were required to heat from this temperature to the maximum temperature (3000°F). Sintering temperatures and times for the specimens of this investigation are indicated in Table I. Analysis of Specimens: Specimens polished with diamond abrasives were etched to reveal the grain boundaries with a 1:1 mixture of 20 pct potassium hydroxide and 20 pct potassium ferricyanide heated to 160°F. Representative areas of each sample were photographed at 1000 diameters. The largest diameters of all well-defined grains were measured, but only the measurements of 15 of the largest grains were averaged in order to determine an index of grain size on the assumption that they were among the first to begin growth. Densities were determined from differential weighing of the samples in air and water. The reported density values are considered correct within ±0.01 g per milliliter. Results and Discussion Metal compacts have exhibited grain growth when sintered at temperatures about two-thirds of the absolute temperature of their melting point.&apos; Grain growth also occurs during the sintering of chromium carbide and is illustrated by the micrographs shown in Fig. 1. These micrographs were prepared from specimens sintered for 90 min at temperatures ranging from 1371°C (2500°F) to 1648°C (3000°F). Average grain size and density measurements of specimens investigated are presented in Table I. The relationship between grain size and sintering tem-

Jan 1, 1954

By G. Delagrammatikas, M. Karmis, J. Mastoris

The evaluation of raw materials in terms of quality profile, mineralogical character and mechanical properties is of great importance to the cement industry. The variability of their chemistry and structure is among the decisive design parameters in the choice of any mining, handling and preblending systems. Furthermore, clinker and cement production require sound estimates of the above parameters, to help produce some appropriate and realistic raw mix configurations and achieve minimum standard deviation of the major components. This paper addresses this subject from the perspective of a cement producer and presents the principles of a methodology aimed at optimizing mine planning and process design. Finally, results from case studies on actual sedimentary deposits currently in operation are discussed.

Jan 1, 2002

By B. Currie

Maintenance of quality electrowon copper requires an electrolyte which has suitable chemical and physical characteristics. The proper design and operation of the solvent extraction plant is essential to the quality of the electrolyte sent to electrowinning. An aspect that is not well appreciated is that the return electrolyte can have negative effects on the operation of the solvent extraction plant. Poor SX plant operation creates below optimum electrolyte conditions. High Eh in the return spent electrolyte can degrade the SX reagent with large decreases in copper transfer capacity and increases in internal entrainment. The synergistic interaction of the SX and EW plants needs a single-source design approach to address the interactions. The design elements in the SX and EW plants required to manage the electrolyte conditions are discussed.

Jan 1, 2014

By Witold M. Pytel

A simplified, three-dimensional, time-dependent, mechanistic model of the overburden-coal seam-floor interaction has been developed and validated at two Illinois coal mines. The model based on the thin plate theory can involve any complex layout of mine workings, time-dependent sequence of extraction and, rheological properties of immediate floor strata. The model output data consist of spatially distributed surface subsidence and its slope and curvature, as well as load acting on pillars in one or more panels. A comparison of calculated and monitored surface subsidence or in-mine convergence measurements has proven the model&apos;s effectiveness for surface subsidence and load transfer prediction.

Jan 1, 1992

By John W. Buch

Upon review of German World War II mining practices and equipment for planning coal, the Federal Bureau of Mines initiated research leading to the development of a pneumatic planer for anthracite. The results of tests are reported in this manuscript. It was demonstrated (1) that hard anthracite can be planed and (2) that the design and operating requirements are within the limits of present-day engineering and technology. For hard anthracite, the depth of cut indicated is 4 to 6 inches; with a chain pull of 20 to 40 tons and the speed of planer travel of 18 to 20 feet per minute, a 40-hp. motor will be required for the planer hoist. Compressed-air requirements for the planer will be 250 to 300 c, f, m, at 60 to 70 p. s, i. It was learned that the length of the 4 individual sections of the planer should not exceed that of the individual troughs of the armored chain conveyor (5 feet in this instance); otherwise, bottom coal will be left in synclines, and the planer will override the conveyor at anticlines. Pneumatic pushers should be operated from a separate compressed-air line fitted with a pressure regulator. Results indicate that additional development work is warranted.

Jan 1, 1957