Search Documents

By C. Bateman, F. Calizaya

"This study presents the results of three laboratory experiments on pressure balancing carried out at the University of Utah’s coal mine ventilation model. The model includes simulations of two working areas, one longwall mine gob, and a set of stoppings and seals. It also includes a pressure chamber between the longwall face and the gob. The model is ventilated by one main fan and one bleeder fan. A carbon dioxide injection system, equipped with flow control valves operated by a microprocessor, is used to pressurize the chamber and to maintain the pressure in the chamber slightly higher than that of the gob. During each experiment, fan pressures and stopping resistances were changed, the carbon dioxide injection rate was regulated, and the differential pressures across the stoppings were monitored so that the chamber pressure is always kept slightly higher than that the gob pressure. Result of these experiments are reported in this paper. INTRODUCTION Spontaneous combustion (Sponcom) is a safety hazard in underground coal mines. The history of coal mining in the US is replete with mine fires and explosions. Sponcpm accounts for approximately 17% of the total number of fires recorded in the U.S. since 1990. In the U.S., by law, worked out areas in coal mines must be either ventilated by a bleeder system or isolated by explosion proof seals. Experience has shown that seals are not airtight structures and that they allow some leakage of air into or out of the gob. In fact, seals “breathe in and breathe out” with changes in barometric pressure (Francart 1997, and Chalmers 2010). These changes in pressure affect not only the methane emission rate but also the ingress of oxygen to the gob, the lower the pressure behind seals is, the higher the ingress of oxygen. In mines ventilated by a U-tube exhaust system, the gob is often kept under negative pressure. Under these circumstances, an increase in barometric pressure may cause an influx of fresh air into the gob. This quantity may be sufficient to start self-heating of the coal, which can lead to spontaneous combustion. Depending on the coal characteristics and the ventilation conditions, self-heating of coal can start at temperatures as low as 35 ºC. If the heat is not removed it will increase the coal temperature leading to ignition and fire. The risk of Sponcom fires can be reduced by isolating the mine gob using rated seals, and implementing a suitable ventilation system. However, isolation seals are not airtight structures, thus some leakage of air is expected unless the pressure in the gob is neutralized. The alternative is to use a pressure balancing system. This requires a thorough knowledge of the ventilation system, the seal/stopping construction techniques, the airflow behavior in the gob area, and the gas build-up behind the seal line."

Jan 1, 2016

By Miles B. Royert

Crude Minnesota taconite was charged in the Bureau of Mines experimental blast furnace so that smelting characteristics of such highly siliceous raw materials could be studied and smelting costs compared with those of a standard Mesabi ore. The Bureau recognized that the highly siliceous nature of the crude ore and its relatively low metallic content would be serious economic deterrents to commercial use of the raw taconite, but compensating factors would be low capital investment in production facilities, large tonnage available on short notice, high recoveries of iron, and low delivered cost. Crude taconite smelted readily in the experimental blast furnace. Coke consumption per ton of metallic product was very high, compared with the average established requirements for smelting normal grades of metalliferous raw materials. Slag rates were also inordinately high. Metal quality was erratic as to silicon, and sulfur contents were objectionably high.

Jan 1, 1961

By Ellis S. Hertzog, James R. Cudworth

Tremendous interest has been evidenced in the subject of dewatering and drying ooal for the past 10 years, and yet little effort has been made to summarize the literature, at least so far as this country is concerned. Only a few published articles have dealt solely with dewatering and drying coal. In most cases the subject has been discussed briefly, either in general terms or as to specific installations. It is desirable that a compendium be prepared collecting in one place information on the dewatering and drying of coal, the needs for this process in various fields, the available equipment, and the current American practice in regard to it. This work was underta..lten by the :Bureau of Mines in cooperation with the University of Alabama. New coal-washing plants in which various types of dewatering and drying equipment were in operation were visited in-Pennsylvania; Ohio, India...~a~ and Illinois. The dewatering·and drying of coel has .been studied in this coimtry by the Surface Preparation ·Committee of the ·coal Operato~s• Committee of the .American Mining ·Oongress. In GermaIJY .it has received the special attention of the Reichskohlenr·at, and in Great Britain of the Utilization of Fuel Commi-t-tee of the Insti ti.ite of Min"ing Engineers.

Apr 1, 1938

By Albert W. Cox

This paper, one of a series prepared for the United States Bureau of Mines discussing the methods used in mining, crushing, and grinding materials for cement manufacture, deals particularly with the methods used at the Security plant of the North American Cement Corporation. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of, total production costs might in many instances cause embarrassment to individual producers as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scone of the cost tabulations shall ensue.

Jan 1, 1932

By S. Torno

The elimination of ultrafine (<10 µm) clay particles is essential to the treatment of abandoned coal-washing plant tailings for the recovery of the remaining coal fraction by enhanced gravity processing. Effective hydrocyclone classification is required to remove this fraction. The highly variable composition and particle size distribution of such wastes creates significant difficulties in the operation of hydrocyclones for such classifications. Hydrocyclone laboratory investigations and their plant setup require lengthy or time-consuming tests. The use of empirical models of such classifications frequently requires modification to correspond to actual operating conditions. Results of the evaluation of computational fluid dynamics (CFD) modeling to predict hydrocyclone classification of coal-washing plant tailings are presented. Results of the standard k-epsilon turbulence, SSG turbulence and large eddy simulation CFD models are compared with the results obtained from analyzed hydrocyclone classifications. The CFD models tested are shown to be very effective in the simulation of hydrocyclone classifications for the determination of the classification particle size and adequate for determining the efficiency index values for many applications. The large eddy simulation model was identified as the most precise, but it is recommended that all three models be improved simulations of classifications above and below the classification particle size.

Jan 1, 2011

By Reimers. Jan H.

Practically all the world&apos;s lead is produced by sintering and blast furnace smelting, or the Imperial Smelting Process which is a variant of the blast furnace process. Increased coke and labour costs and strict lead emission limits have, however, made blast furnace smelting undesirable in most countries. A change-over to other lead smelting processes providing better working conditions and lower emissions is, therefore,. expected to occur once economic conditions improve and the necessary capital expenditures can be justified. The need for new lead smelting processes has long been evident and a number of new processes have been proposed &apos;and advanced to various stages of development. One of the new processes is already proven on commercial scale, while several others are still being tested on pilot plant scale.

Jan 1, 1983

By Albert L. Toenges

The Deep River coal field is in Chatham, Lee, and Moore Counties, N. C. The coal-bearing part of the basin is about 35 miles long and 5 to 10 miles wide. Sanford, the county seat of Lee County, is the largest town in the area, with a population of 10,000. Four railroads provide transportation to the area, and four United States highways and improved county roads provide easy access to the field. The Carolina mine at Farmville is the only operating mine in the field. The mine was opened in 1921 by two rock slopes driven from the surface to the Cumnock bed. Mining operations continued intermittently until 1945 and then stopped. In the fall of 1947 the mine was reopened by the newly organized Raleigh Mining Corp.

Jan 1, 1952

By E. R. Dotson

Kaolin is an important industrial mineral. It has unique properties, which combined with its low cost, make it suitable for use in a wide variety of products. Kaolin is defined as "any of a group of clay minerals, including kaolinite, nacrite, dickite, and anauxite, with a two-layer crystal in which silicon-oxygen and aluminum-hydroxyl sheets alternate; approximate composition is AlZ03-ZSiOZ-1/ ZHZO".-The kaolin discussed here is composed chiefly of the mineral kaolinite. Kaolin is also commonly referred to as "china clay". Approximately 4.9 kkg (5.4 million short tons) of kaolin was sold or used in the United States, and .8 million kkg (.9 million short tons) was -exported in 1974. In domestic usage, paper coating and filling accounted for 43% of the total, fol-2/ lowed by refractories, rubber, and ceramics.-Figure 1 shows the amount of kaolin sold or used by domestic producers for specified uses for the years 1963-3/ 1973.- Kaolin was produced at mines in 14 states, but Georgia accounted for 75% of the 1974 domestic production. The average value for all grades was $36.00/kkg 4/ ($32. 67/ton) .-

Jan 1, 1977

By S. K. R. Iyengar

This report presents the results of a study to develop optimal designs for light-weight mine roof supports for use in underground coal mines. A load capacity of 196 kN (22 tons) and a height adjustable between 1.829 m (72 inches) and 2.438 m (96 inches) were taken as the design parameters and the design goal was a unit weighing less than 22.3 kg (50 lbs). Three alternative design concepts were explored, viz. mechanical, hydraulic, and hydro-mechanical and a total of 13 designs analyzed in detail. Steel, aluminum alloy and composites were the main potential construction materials investigated for suitability from structural, life, and safety and other considerations. The designs considered most promising for development were: (i) the mechanical screw-pin type using telescopic tubes and a fine adjustment screw thread section (ii) the all-hydraulic type, of steel, aluminum alloy or aramid graphite construction (iii) the hydro-mechanical design using telescopic tubes and a short stroke hydraulic cylinder for fine adjustment It is shown that by using realistic mathematical models for stress and deflection calculations, it is possible to reduce prop weight to the design goal. The analysis presented for all-hydraulic props is applicable to hydraulic cylinders on all mining equipment and similar machinery. This report includes the computer program and user&apos;s guide for analyzing hydraulic cylinders as well as a cross-indexed bibliography on structural composites.

Jan 1, 1978

By E. S. Malloch

THE Great War forced the peoples of the world to recognize the importance of the wise development and use of the world&apos;s natural resources. Not the least, and perhaps the most, important, is the world&apos;s fuel supply- solid, liquid, and gaseous. Without fuel our civilization would be impossible, and mankind would of necessity have to congregate in the torrid zones of the earth&apos;s surface for at least six months of every year. Of the three classes of fuels the solid ones are the most plentiful, as well as being the most widely distributed, since few countries are entirely devoid of solid fuels of one kind or another. Until a hundred years ago wood was the fuel most generally used in this country, but since then coal has supplanted wood as a fuel in all its uses, except in the outlying districts and among the farming communities. For many years the supply of coal was thought to be unlimited, but as years went by more thought and study were given to the world&apos;s coal resources, until today not only are the limits known, but in one instance at least their depletion is predicted to be almost within the age of living men, unless more provident methods are put into practice for their winning and utilization.

Jan 1, 1928

By J. J. Jakosky

THE method of electrical mapping of oil structures to be described possesses certain limitations, as well as certain definite advantages. It, in common with other geophysical methods, is not a panacea for the solution of all subsurface geological problems. It operates on differences in electrical conductivity of the geological strata, whereas the other most-used methods operate on (1) differences in magnetic properties, (2) differences in gravimetric properties, or (3) differences in seismic properties. This modification of the resistivity method is therefore able to obtain subsurface information under conditions not favorable to the other methods mentioned. Where the other methods have been employed with ambiguous results it may act as a complementary method.

Jan 1, 1936

By R. T. Langland

The U.S. Bureau of Mines has conducted underground tests and computer analyses to study coal mine roof behavior. Southern Ohio Coal Company provided test sites it) their Heigs mines located near Athens, Ohio. Testing apparatus was adapted for monitoring roof behavior at the face of mining from a remote surface location. Finite element analyses were applied to study the structural conditions present. Test sites were located at three different intersections of entries and crosscuts of the room-and-pillar mine. Electrical read-out instruments were used to record roof bolt loads, roof sag, and roof-floor convergence. They were installed during the roof bolting cycle of a conventional mining section and data was recorded for several months. Normal mining operations continued throughout the test period with minimal interruptions due to the installation and monitoring of the instruments. A computerized data acquisition system, partly underground, partly on surface, permitted continuous monitoring of data and its retrieval, display, manipulation, and storage. The finite element code used to model the test sites accounted for three-dimensional geometry, nonlinear material behavior, and the mining excavation and bolt installation sequences. Results of the test are highly variable. Comparable values between test and analysis results were obtained by applying statistical averaging of. roof test data. Results of the analyses indicate that bolts have a lesser effect on the gross behavior of mine roofs than has been indicated and that bolt load changes are strongly influenced by mining excavation sequence, bolt-placement sequence, and face distance

Jan 1, 1977

By Chris Vagasky

On July 10, 1926, lightning struck at Picatinny Arsenal, New Jersey, and caused the explosion of at least 600,000 pounds (272,000 kilograms) of ammunition, resulting in more than $600 million (2015 dollars) in damage, the destruction of 200 buildings, and 22 deaths. Fortunately, there has not been a major incident involving lightning and explosives in the US in some time, though lightning has destroyed fuel storage tanks in recent years, including in North Dakota, Texas, and Ohio. Lightning poses a significant hazard to the explosives industry. Carrying high currents and temperature, lightning can cause explosives to detonate, start fires near storage facilities, and injure or kill operators.

Jan 1, 2017

By J. O. Wheeler

"DEFINITION OF THE REGION, ITS BOUNDARIES, AND PHYSICAL AND GE'OLOGICAL CHARACTERISTICSTHIS PAPER concerns the Western Cordilleran region, embracing most of British Columbia, the southern half of Yukon Territory and the southwestern most part of the District of MacKenzie. It excludes Vancouver Island and the Queen Charlotte Islands, which are discussed in a background paper on the Pacific Continental Shelf. The region is bounded on the south by the northwestern United States, on the west by the continental shelf and Alaska, on the north by the front of the Ogilvie Mountains, on the northeast by the axis of the MacKenzie Mountains and on the east by the Rocky Mountain Trench.The region is dominated by two mountain chains that con tain icefields and glaciers: the St. Elias, Coast and Cascade Mountains in the west; the Selwyn, Pelly, Cassiar, Omineca and Columbia Mountains in the east. The Intermontane region between these mountain chains consists of lower mountains and plateaus. In the mountains, the region above the timberline and many of the steep valley-walls provide good exposures of rock, but these areas are subject to rockslides and landslides and in winter to snow avalanches. Much of the Western Cordillera was covered by ice-sheets at various times during the Pleistocene epoch. Consequently, the larger valleys in the mountains and much of the Intermontane region contain much glacial drift and alluvium and only limited exposures of rock. This same terrain in the Southern Cordillera, however, is the most favourable for agriculture. Parts of the region, particularly in the two mountain chains, are heavily forested. Elsewhere, the forest cover is less, with grassland prevailing in the south and tundra in the north."

Jan 1, 1969

By J. O. Wheeler

"DEFINITION OF THE REGION, ITS BOUNDARIES, AND PHYSICAL AND GE'OLOGICAL CHARACTERISTICSTHIS PAPER concerns the Western Cordilleran region, embracing most of British Columbia, the southern half of Yukon Territory and the southwesternmost part of the District of MacKenzie. It excludes Vancouver Island and the Queen Charlotte Islands, which are discussed in a background paper on the Pacific Continental Shelf. The region is bounded on the south by the northwestern United States, on the west by the continental shelf and Alaska, on the north by the front of the Ogilvie Mountains, on the northeast by the axis of the MacKenzie Mountains and on the east by the Rocky Mountain Trench.The region is dominated by two mountain chains that con tain icefields and glaciers: the St. Elias, Coast and Cascade Mountains in the west; the Selwyn, Pelly, Cassiar, Omineca and Columbia Mountains in the east. The Intermontane region between these mountain chains consists of lower mountains and plateaus. In the mountains, the region above the timberline and many of the steep valley-walls provide good exposures of rock, but these areas are subject to rockslides and landslides and in winter to snow avalanches. Much of the Western Cordillera was covered by ice-sheets at various times during the Pleistocene epoch. Consequently, the larger valleys in the mountains and much of the Intermontane region contain much glacial drift and alluvium and only limited exposures of rock. This same terrain in the Southern Cordillera, however, is the most favourable for agriculture. Parts of the region, particularly in the two mountain chains, are heavily forested. Elsewhere, the forest cover is less, with grassland prevailing in the south and tundra in the north."

Jan 1, 1970

By Linfeng Zhou, Rong Sun, Guanghui Li, Zhiwei Peng, Tao Jiang

Dust, or airborne particulate matter, from metal smelting can be either mechanically or thermally generated and it negatively affects the indoor air quality as well as the fugitive emissions from the plant. The thermally generated dust is often referred to as fume and it is typically generated whenever liquid metal comes into contact with air. For practical reasons, such as vehicle access, etc. it is often difficult to collect 100% of the fume. It is therefore highly desirable to develop processes and optimize operational procedures so that fuming can be kept to a minimum. In this series of experiments, the mechanism of active oxidation and fume formation from liquid silicomanganese under an impinging air jet in the temperature range 1400-1600°C has been explored. Characteristic properties of the fume have been established; particle diameter, shape, size distribution, and elemental composition are reported. The oxidation process is described in terms of vaporization, oxidation and agglomeration. In the boundary layer, two competing mechanisms seem to be operative in parallel: a direct oxidation of Mn vapor, and a two-step oxidation of silicon. The thermodynamic and kinetic conditions governing the two mechanisms are discussed.

Jan 1, 2016

By Herty, C. H.

No attempt will be made here to review the previous work done by investigators on the general subject of inclusions, because it was discussed sufficiently in an early cooperative bulletin of this series (No. 36, 1928), and reference was then made to general bibliographies. The work described in this present bulletin deals directly with the study of the mechanism of deoxidation of steel with aluminum and the formation of inclusions containing alumina. Unquestion- ably, such inclusions are encountered in most steel-making practices and little has been done to determine their characteristics. Aluminum is used to ensure rapid deoxidation during the solidification stages of the steel. For this reason the possibilities of inclusion elimination are slight and alumina-containing particles will undoubtedly be present in the ingot. Besides this common practice, aluminum is often used in the ladle with other deoxidizing agents such as silicon and manganese. Ladle additions of aluminum are made to rimming steels to obtain the correct partial deoxidation desired in this type of steel. In killed steels the aluminum is added to ensure soundness, as far as blowholes are concerned, in the ingot. In either rimmed or killed steels, alumina or alumina-containing inclusions are found therein, the amount and type depending on the oxidation of the metal, the amount of aluminum added, and the addition of other deoxidizers.

Jan 1, 1957

By M. Fafard, F. Chevarin, D. Ziegler, H. Alamdari, M Kavand

"Carbon anodes, used in the Hall-Heroult process, are consumed by the electrochemical reaction to produce metallic aluminum. It is also consumed by parasitic reactions with air and CO2. The carbon anode is made of petroleum coke with different particle sizes, butts (recycled anodes) and coal tar pitch. The mixture of fine particles (less than 150 µm) of coke together with the pitch material forms a matrix, binding the large coke particles together. It is generally thought that the binder matrix is more reactive than the other anode constituents. This conjecture was not clearly proved in the literature. The present study is focused on the CO2 reactivity of binder matrix and anode constituents at 960°C, both under chemical regime (100% of CO2) and under a concentration gradient (diffusion). The apparent reaction rates of these materials were measured. The role of the binder matrix in anode consumption and its disintegration (dusting phenomenon) was discussed.INTRODUCTIONThe metallic aluminum production is one of the most important industries in Canada. The Al metal is obtained by the Hall-Héroult process. The principle of this process is the electrochemical reduction of alumina in molten cryolite carried out by an electrical current between carbon anodes and cathode at 960°C (Equation 1). The carbon anode is typically composed of calcined petroleum coke (65 wt.%) and recycled anode (called also butt, 20 wt.%) with coal tar pitch (15 wt.%), playing the role of cement to ensure the cohesion of the anode block."

Jan 1, 2016

By Arel B. McMahan

The U.S. Bureau of Mines investigated mines, prospects, and mineralized areas in the Owlshead Mountains Wilderness Study Area (WSA) in 1982. Within the WSA, subeconomic manganese, iron, zinc, and lead resources were identified at two mines; sample analyses indicate five other mines and prospects may have gold, silver, iron, manganese, and copper resources. Three mines examined adjacent to the WSA have identified manganese and iron resources; and sample analyses indicate manganese, iron, and gypsum resources may exist at two prospects. Greatest likelihood for future identification of mineral reserves is for manganese at the Black Magic Mine in the southeast part of the WSA. The southern half of the WSA contains nearly all identified mineral resources, and properties at which sample analyses indicate additional resources. The most significant are manganese and iron resources at the Black Magic Mine in the southeastern part of the WSA; and the Ellie, New Deal, and Owl Hole Mines adjacent to that part of the area. Manganese and iron minerals filled fractures and replaced limestone in brecciated and faulted contacts with intrusive granitic rocks. In the southwest corner of the WSA, sample analyses indicate four prospects may have gold and silver resources. These precious metals are in gouge zones along contacts where diorite has intruded volcanic rocks. A small identified resource at the Kennedy Boys Lead Mine in the western part of the WSA consists of quartz veins with zinc and lead minerals along a brecciated contact between granite and limestone roof pendants.

Jan 1, 1985

By Allan Sylvester

This paper will discuss the design, construction, and performance of the support of excavation on the San Diego State University LRT Station. The vertical elements of the system include drilled secant piles and drilled soldier piles. We will discuss the geo-technical characteristics, design and construction considerations, loading criteria, construction techniques, schedule constraints, and performance of the pile and support of excavation systems. In consideration of the conference theme, there will be a discussion of the successful accomplishment of meeting the interim milestone dates of the Contract. The project team cooperatively worked to design and install approximately 1,100 drilled secant and soldier piles as well as excavate and install the balance of the support of excavation elements in such a manner as to minimize the disruption to campus students and operations.

Jan 1, 2002