Search Documents

By W. Abdellah

The purpose of this paper is to establish a qualitative method to estimate the risk level (e.g. rating and ranking) resulting from mining activity. Risk is the product of two factors: probability of failure and cost of consequences. A resultant assessment scale matrix is then used to assign a risk index value which is directly proportional to the potential for excavation instability. A case study, the No. 1 Shear East orebody at Vale?s Garson Mine in Sudbury, Ontario will be examined. A three-dimensional, elastoplastic, finite difference model (FLAC 3D) is presented for a mine development intersection situated 1.5 km below ground surface. The developed assessment scale matrix is used to estimate risk index for intersection (2981) located on 5000 level. The results are presented and categorized with respect to risk-index value, probability of instability, cost of consequence, and mining stage.

Jan 1, 2014

By Srinath Viswanathan, Adrian Sabau

"In general, the occurrence of microporosity during metal casting is due to the combined effects of solidification shrinkage and gas precipitation. The governing equations for fluid flow and hydrogen evolution indicate that porosity formation and fluid flow are strongly coupled. However, in most studies on microporosity, it is considered that the porosity formation does not influence the fluid flow in the mushy zone. In this study, a computational methodology is presented for the numerical simulation of interdendritic fluid flow and microporosity evolution. The solution algorithm presented includes a fully coupled, implicit treatment of microporosity and local pressure in the mushy zone. The effects of microporosity evolution due to the local pressure drop in the mushy zone, and pore expansion in casting regions where liquid feeding alone cannot compensate for the solidification shrinkage are also considered. It is shown that neglecting the effect of porosity formation on the pressure in the mushy zone yields higher pressure drops. By its growth, microporosity partially compensates for the solidification shrinkage, reducing the feeding demand. A reduced feeding demand requires less fluid flow to compensate for solidification shrinkage, and results in smaller pressure drops in the mushy zone. Therefore, in order to accurately describe casting defects, comprehensive models of fluid flow, heat transfer, and solidification must include the effect of microporosity as well.IntroductionIn the terminology commonly used by foundrymen, porosity is usually considered to be either ""hydrogen"" or ""shrinkage"" porosity. Hydrogen porosity is the term given to porosity that is generally rounded, isolated, and well distributed. Porosity that is interconnected or clustered, and of an irregular shape corresponding to the shape of the interdendritic region, is usually termed shrinkage. In general, the occurrence of microporosity in aluminum alloys is due to the combined effects of solidification shrinkage and gas precipitation [1]. Continuum models [1, 2- 7] have been used to predict the level of porosity in castings. A number of other studies have also attempted to understand the phenomena of porosity formation and pore growth [8-10] and pore morphology [11].The governing equations for fluid flow and hydrogen evolution indicate that porosity formation and fluid flow are strongly coupled. However, in most studies [4, 9, 10], it is considered that the porosity formation does not influence the fluid flow in the mushy zone. Kubo and Pehlke [3] presented a methodology for the prediction of microporosity distribution in shaped castings by considering the effects of both the hydrogen precipitation during solidification and the pressure drop in the mushy zone. In their approach, the local pressure and porosity were computed in an uncoupled manner based on a ""flux of interdendritic liquid"" criterion, i.e., either pressure or porosity was first computed using the other variable at the previous time step. Their approach has been used with little change in numerous studies [6, 12, 13]. Recently, Kuznetsov and Vafai [14] presented a fully coupled, one-dimensional model for the computation of pressure and porosity. They showed that neglecting the effect of porosity formation on the pressure in the mushy zone yields higher pressure drops and an over-prediction of final porosity. They also showed that the influence of porosity formation on the pressure is larger at lower pressures in the mushy zone."

Jan 1, 2001

By C. Pelley, A. Piche

"The Canadian mining industry faces the prospects of a severe shortage of graduate mining engineers over the next decade. This arises from three factors: first, a growth in industrial activity; second, the average age of company engineering and management staff; and third, the reduced number of students in engineering faculties around the world. This paper aims to identify the critical factors underlying the trend of inadequate recruitment into higher education for mining and to examine means of alleviating the problem.This paper is based upon surveys of potential and current students and graduate mining engineers from four mining schools. An attempt is made to understand institutional and industrial images, career prospects and what is required to attract enough high-calibre young people into mining education over the next decade.IntroductionThe mining industry has started to experience a severe shortage of graduate mining engineers which is likely to persist and even worsen in the short- to medium-term.This arise s from three principal factors:1. a recent and strong growth in mining activity, which surpasses that experienced through the 70s, before the recent international industrial recession; .2. an increasingly older average age of mine engineering employees, at least in the industry's larger companies; and3. problems associated with maintaining adequate mining undergraduate recruitment levels ."

Jan 1, 1989

By J. D. Bardill

"The Stoddard mine, Cheshire County, N. H., was explored by the Bureau of Mines in 1944 as a source of the strategic fluorite. It was reported that the vein persisted in the bottom of old workings and the geology of the immediate area indicated the possibility of finding additional lenses.In its program of exploration of mineral deposits, the Bureau of Nines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts pre¬liminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director.Special acknowledgment is expressed for the cooperation and assistance given by Robert F. Sherwood of the United Feldspar & Minerals Corp.; by McHenry Mosier, chief, College Park Division, Mining Branch, who aided in re¬vising this report; and by J. B. Zadra, chief, College Park Division, Metallurgical Branch, and others of his staff, who assisted in performing the beneficiation tests and analyzing samples. The field work was under the direction of Harry P. Hermance.The property lies on the southern boundary of the town of Westmoreland, Cheshire County, N. H., at approximately 72° 39’ west longitude, 42° 27’ north latitude, in the Keene, N. H. (G.S.) quadrangle.Good gravel roads lead from paved State Highway 63 to the property. A dirt road in fair condition suitable for truck leads to the nine.Dwight H. Smith, Putney, Vt., is the owner and has leased the property to the United Feldspar & Minerals Corp., 10 East 40th Street, New York 16, N. Y.Property titles were not investigated.The fluorite deposits of Cheshire Count', H. H., have been known for many years, being reported by Jackson, (Geology and Mineralogy of New Hampshire, by Charles T, Jackson, 1844) and by Hitchcock, in1878 (Geology of Now Hampshire, vol. 3, 1878, by Charles H. Hitchcock). A large pit on the largest or east vein was mined by Lovat Frazer from about 1908 to 1917, This operation is reported to have produced approximately 3,500 tons of fluorspar. In 1917, the American Steel & Wire Co, took over the mine end is said to have produced 3,500 tons of fluorspar before relinquishing the lease in 1923.From 1935 to 1937 the New Hampshire Fluorspar Cc. operated the Stoddard mine, working chiefly on the most westerly of the three known veins on the property, as well as doing some preliminary work on the small central vein. In 1938, the United Feldspar 6 Minerals Corp. leased the mine, and less than 100 tons of fluorspar was produced from exploration and development work, No mining has been done since that time."

Sep 1, 1946

By E. E. Wahlstrom

The Harold D. Roberts tunnel, in Summit and Park Counties, Colorado, is a concrete-lined pressure tunnel finished to a circular cross section of 10.25 ft diam. The tunnel is 23.3 miles long and is designed to transport water for domestic use by the City and County of Denver from reservoir storage at Dillon to a tributary of the South Platte River at Grant. The tunnel passes beneath the Continental Divide at the crest of the Front Range and intersects rocks of diverse types and origins and geologic structures of extreme complexity. Geologic investigations preceded and were continued during construction and contributed materially to the safe and economical advance of the tunnel headings. Geological data obtained and evaluated during construction include plans and sections on a scale of 1 in. to 50 ft, rock temperatures at 2000-ft intervals, records of progress related to geology, records of ground-water conditions, summaries of the use of steel and timber supports, and summaries of grouting operations. Adverse conditions required use of steel and timber supports for 71.74% of the total length of the tunnel. Most supported sections reached a condition of equilibrium within a few hours to a few months after being excavated, and the concrete lining serves chiefly to provide an additional safety factor and to provide necessary hydraulic characteristics to the tunnel. Efforts to attain a maximum rate of advance of the tunnel headings necessitated use of more steel and timber supports than would have been required in a less accelerated tunneling operation. This report summarizes geologic investigations prior to and during construction of the Harold D. Roberts tunnel in Summit and Park Counties, Colorado (Fig. 1) and analyzes the tunneling operation as it is related to the various kinds of geologic conditions encountered in the tunnel. The tunnel is concrete lined to a circular cross section of 10.25 ft and is designed to transport 788 sec ft from reservoir storage at Dillon 23.3 miles along a dog-leg course passing under the Continental Divide to outlet and control works at Grant, Colo. The primary purpose of the tunnel is to augment the domestic water supply of the City and County of Denver, but plans include provisions for power generation at the outlet portal at a future date. Location of the tunnel was made after extensive preliminary geologic and engineering investigations by the Board of Water Commissioners of the City and County of Denver, and the U.S. Bureau of Reclamation. In 1946 the Board of Water Commissioners started tunnel driving on a limited scale from the east (outlet) portal and by 1955 had completed 9986 ft of tunnel. An urgent need for additional sources of water supply required acceleration of the tunneling operation, and, in 1955, Tipton and Kalmbach Inc. of Denver were assigned the responsibility of reviewing the project and preparing plans and specifications for the tunnel and appurtenant features. Additional geologic studies were made, and the geology of several possible alternate tunnel lines were compared before determining that the tunnel should be driven along the course previously adopted by the Board of Water Commissioners. On July 12, 1956, a contract for construction was awarded to Blue River Constructors Inc., a combine

Jan 1, 1962

By Stratton-Crawley R., G. E. Agar

"A study has been done of the scale-up of laboratory bench-scale flotation to continuous plant circuit performance. It was found that the impellor speed and the air flow rate influenced the results and in this case extreme values of these operating variables were required in order to reproduce the plant rougher results in the laboratory. Despite the experimental uncertainty introduced by these extreme values, it was demonstrated that the plant performance could be predicted and experimentally reproduced with bench-scale tests.IntroductionThe mineral processing industry relies heavily on batch flotation testwork to design flowsheets, evaluate reagent s and compare various types of ore. The batch tests are generally regarded as being directly comparable within themselves, but quite often they relate poorly or not at all to continuous circuits. Obviously this dilemma generates considerable uncertainty with wide-ranging ramifications. One of the manifestations of this unfortunate situation is the commonly expressed opinion that ""it may work that way in the laboratory, but it will never work that way in the plant"".In a previous publication, a method was described whereby the results of batch bench-scale tests could be used to simulate a locked cycle flotation test series. The work to be described here is a continuation of that investigation with an extension to the simulation of an actual plant circuit. It would have been preferable to progress from laboratory batch data to a continuous pilot plant and then finally to a full-scale plant operation. However, because that possibility did not present itself, an attempt will be made to show that the performance of an existing plant circuit can be successfully simulated from batch data. The success of the procedure can be judged by the agreement among the plant results, a locked cycle test and the predicted results based on batch tests."

Jan 1, 1982

By Paul Billingsley

THE purpose of this paper is a comparison, based on genesis, of the ore deposits associated with the igneous rocks of the central Montana Rockies. Considered separately, without attention to their origin, the orebodies appear to be distributed haphazard, with no fundamental laws controlling their position and character. It is believed, however, that if all the factors be weighed, this apparent confusion will to a large degree disappear. The, first essential to such a comparison is detailed knowledge of the individual mines, as to their geographic position (see Fig. 1), their mineralogical character, and in particular the derivation of their ores.1 The authors of this paper have pursued such an investigation for the past 6 years, and have accumulated a mass of evidence that enables a preliminary correlation to be attempted. It appears that the majority of ore deposits are genetically related to one or another of the igneous

Jan 4, 1917

By A. P. Massmann

Design for economical operation, minimum operating labor and minimum maintenance for labor and supplies are virtually inseparable. Each consideration has a vital bearing on the other. Let us assume that we have the design complete for the most economical operation with a minimum of operating personnel. This means, in addition, that we have the fewest number of operating units consistent with the product requirements for a team or metallurgical coal which we are called on to produce. The number of units will vary greatly, being influenced by design, washability characteristics, tonnage and degree of quality control necessary by reason of producing a product for metallurgical, steam or domestic use. The units involved most ordinarily for any type coal preparation plant will number as a minimum the following: 1. Hoppering R.O.M. Coal 2. Feeding

Jan 1, 1959

By Sherwin F. Kelly

FRONTIERS of geological knowledge retreated further this past year before an ever-widening geophysical attack, as governments and endowed institutions continued to take an increasing practical interest in the geophysical line of approach to the study of earth phenomena. A year ago I opened this annual review with a brief account of the efforts to discover what formations lie concealed beneath the deep sediments which form the superficial portions of the Continental Shelf off the eastern United States. That work was but the beginning, and 1938 saw its continuation and expansion. With the assistance of a Guggenheim Fellowship, Maurice Ewing pushed his researches in the development of instruments and techniques for deep-sea seismic refraction studies. Ewing's early refraction profile from the Virginia Capes to the edge of the Continental Shelf has been followed by a similar traverse in Great Britain from the coast of Cornwall to the edge of the Continental Shelf southwest of England. This showed that the thickness of the sedimentary mantle and the rates of slope of the basement surfaces there are comparable to those in the Virginia Cape district.

Jan 1, 1939

By P. G. Kovalchik

Overexposure to noise remains a widespread, serious health hazard in the US mining and other industries despite 25 years of regulation. Most categories of illnesses and injuries associated with mining have improved, with the exception of hearing loss. The drilling of rock in a confined work environment contributes to high levels of noise exposure in mining. The National Institute for Occupational Safety and Health (NIOSH) is conducting research to reduce the noise exposures of jackleg drill operators and to prevent additional cases of noise induced hearing loss (NIHL) by developing and evaluating low-cost retrofit noise controls for equipment. This report describes the procedure for the measurement and reporting of noise from portable pneumatic tools such as jackleg drills. The technique used in this research allows for the determination of the source A-weighted sound power levels and the radiation patterns in octave and 1/3 octave bands. Overall sound power level is also determined. This paper also reports the results obtained by using this procedure to evaluate a SECO S215 standard production drill and a CSIR Miningtek prototype rock drill incorporating engineering noise control measures. It was found that by using the manufacture?s recommended operating pressure of 496 kPa (72 psi) that the CSIR prototype?s sound power was 10 dB(A) less then that of the SECO S215.

Jan 1, 2009

By Marcus M. Key

Silicosis among metal miners is an ancient disease, probably as old as mining itself.' However, the primitive forms of mining were not productive of much silica dust, and the short life span of slaves used in mining probably precluded the development of more than a few sporadic cases of silicosis. Early diagnostic terms of miners' asthma and miners' phthisis suggested an occupational relationship and a tubercular component, but little attention was given to silicbsis until the turn of this century when epidemics of silico-tuberculosis arose due to the great expansion of the mining industry in the United States, especially silver and gold mining. The expansion was accompanied by mechanization and the introduction of pneumatic tools, which generated increasing amounts of fine silica dust. Mining communities were crowded and hygiene was poor.' The tubercle bacillus would probably have flourished even without the predisposition of silicosis.' As is so often the case in occupational health, biostatistical analyses first called attention to the problem, and environmental-medical studies later confirmed its existence. The bio-statistical analyses were occupational mortality statistics compiled by the Prudential Life Insurance Company in 1907, showing evidence of excessive mortality from tuberculosis and relationship to dust exposure. I The

Jan 1, 1971

By C. Breeds, K. Jeremiah, E. Jennings

Washington State has a well developed set of blasting regulations which have been promulgated by the Department of Labor using extensive stakeholder input, not only from citizens but also from manufacturers and representatives of IME, blasters in charge, blasting engineers, blasting companies, local and federal law enforcement agencies, fire officials, and local and state government representatives. WAC 296-52 therefore provides a foundation or platform for developing city ordinances for Washington State cities should a City wish to do so. On the other hand, Oregon’s code is based on OSHA 1926, Subdivision U, Blasting and the Use of Explosives which provides scant direction regarding the modern use of explosives. Reference is also made to ODOT Section 00335 - Blasting Methods and Protection of Excavation Backslopes. This paper examines two separate programs that have been developed by two Cities, one in Washington State and one in Oregon to further regulate blasting inside City limits and discusses why the lack of a regulatory foundation made one approach more difficult than the other. One of the authors was retained by the City of Kennewick, WA to develop their ordinance and has more recently followed and reacted to a pending ordinance for the City of Redmond, Oregon. The paper will compare and contrast the different approaches and comment on the reaction from both Blasters and the public. We also present a case study that involved blasting in an urban area of Oregon to prepare a foundation for a water tank. Controlled Blasting was carried out within 70-ft of residencies and within a community that had expressed reservations regarding blasting even though the work would make a significant contribution to the betterment of the community. Pre-construction surveys of residencies located in a large area surrounding the site were performed and a well-planned blasting program was carried out. Residencies were subject to vibration levels that were monitored using six seismographs that surrounded the site and these units measured vibration levels that were significantly lower than allowed by statute. There were complaints triggered by individuals reactions to blast vibrations which validated commonly held models of human perception but no damage was caused by the Blasting.

Jan 1, 2024

By R. J. Colony

DEPOSITS of iron are widely scattered in the folded Cretaceous rocks and the associated igneous intrusives of Puerto Rico. Most of them are too small for commercial development, but a few have aroused some scientific and economic interest, among them the large body of residua] limonite at the west end of the island near Mayaguez1-6 (Fig. 1) and the mixed hematite and magnetite deposit on the southern slopes of the Sierra de Cayey, about four miles north of Arroyo.7-9 Neither of these orebodies has been developed, nor have investigations of the widely distributed deposits of magnetite, which include all the remaining occurrences of iron deserving of economic consideration, proceeded beyond the exploratory stage. With the possible exception of the mixed deposit near Arroyo, the magnetite is directly associated with andesitic and dioritic intrusives, which invade the Cretaceous rock section, and the bulk of it, occurring in calcareous sediments, is clearly of contact-replacement origin. The small deposit on Rio Portugues, north of Ponce, is found in a limestone band near its contact with an andesite dike.10,11 Two deposits of unde-

Jan 1, 1935

By Jr. Chilson

This paper addresses the slurry pump industry as it exists today by touching on the business aspects, and by discussing research and development for material metallurgy and hydrodynamics for wear improvement which reduce operating and maintenance cost for the customer. It demonstrates why OEM parts give better value for cost.

Jan 1, 1996

By Bruna Brito Freitas

O processo de soldagem por fricção é uma técnica recente que vem sendo desenvolvida a fim de melhorar a qualidade das estruturas offshore. Com a finalidade de aperfeiçoar essa técnica é importante estudar as propriedades metalúrgicas do material soldado. Este trabalho tem como objetivo avaliar a tenacidade ao impacto de um aço C-Mn soldado por fricção com pino consumível, conhecido como FHPP (Friction Hydro Pillar Process). Desta forma, no presente estudo o material foi soldado, tratado termicamente, e após avaliado através de análises metalográficas, de microdurezas e ensaios de impacto Charpy. Como resultados foram geradas microestruturas para as diferentes regiões da solda e foram obtidos valores de energia, segundo a norma ASTM E-23. Por fim, conclui-se que o material não processado apresentou uma tenacidade superior a região de interface soldada, devido as diferentes microestruturas geradas no processo.

Aug 16, 2017

By T. Johnson

Hydrometallurgical processes can be exceptionally corrosive. This is particularly true in acid leaching processes for copper, cobalt, nickel and rare earth elements. In the last five years, several large hydromet plants have been built in North America (Vale - Long Harbour, Baja Mining ? El Boleo and MolyCorp - Mountain Pass). Hundreds of storage tanks, extraction vessels and electrowinning cells along with miles of piping were designed and fabricated to withstand the aggressive environments inherent in these processes. One key element all three projects had in common was the extensive use of FRP in equipment design. As a material of construction, FRP provided equal if not improved durability relative to alternative corrosion resistant alloys at a considerably lower cost. This paper will highlight the extensive use of FRP in these three world scale projects and why it was chosen for each process.

Jan 1, 2013

By Priyadharshini M. R., Premalatha K

"Abstract With the development in the construction of heavily loaded structures, the necessity of pile foundations has increased. For the transfer of heavy loads, it is mandatory that the piles need to be socketed in the underlying rock strata. The load transfer in bored rock socketed piles is by end resistance or the combination of shaft and end resistance which in turn depends on the length of the rock socket. The determination of socketing length of the pile at present is mostly based on a few factors which affect the pile load transfer mechanism. The effect of all the possible factors involved, need to be studied in proposing guidelines for the design of rock socketing length of the pile. Analyses are carried out using finite element analysis software (PLAXIS 3D Foundation) to understand the influence of the thickness of overlying strata for different socket lengths of piles in weak rock. From the load settlement curves, the influence of the overlying soil on the rock socket length isobserved and an effective rock socket length is proposed.IntroductionThe determination of socketing length of the pile at present is mostly based on a few factors affecting the pile load transfer mechanism, which sometimes give a better design and sometimes an uneconomical design. Too much socketing length results in more construction time and higher costs. Therefore, the effect of all possible factors involved need to be studied in proposing guidelinesfor the design of t h e r o c k socket length of the pile.The factors that affect the termination criteria of the rock socketed pile are the capacity requirement, thickness and properties of the overlying soil, characteristics of the founding strata, drilling tools used, roughness of the rock socket and nature of loading.A comprehensive study was performed to understand all the above mentioned factors in different types of rocks. In this paper discussion is made on the settlement results, specifically the influence of overlying sand of different densities above a weak rock. The influence of stress developed is not discussed, keeping in mind the size of the paper under study."

Jan 1, 2014

By Douglas Glenn Stalheim

The demands for improved mechanical properties in hot rolled long products are increasing as the expectations of global Standards and construction designer’s increase. Cost constraints limit the excessive use of expensive alloys to meet these expectations. In addition, depending on the mill, equipment can limit what can be realized to meet the increasing expectations. The most effective way to meet the increasing expectations for improved mechanical properties of optimum strength and ductility is through producing steel with as fine as possible uniform cross sectional grain size in the “as-rolled” condition. The best solution to the development of this fine and uniform cross sectional grain size is to develop a cost effective alloy design coupled with proper metallurgical process control implemented into an existing mill’s equipment capability and layout. In other words, properly bringing together alloy, metallurgy, process control and existing equipment capabilities to develop an optimum product that can meet the increasing demands of the construction designer. This paper is designed to give a solid understanding of the production and metallurgical requirements to achieve a grain size in “as-rolled” long products that is as fine as possible within the limitations of the process and production parameters of the individual plant.

Jul 30, 2018

By Thomas Brownfield

Development and production activity in Oklahoma during the year 1940 was of routine nature. Production, according to the Corporation Commission's figures, averaged 409,100 bbl. daily as compared with 421,000 bbl. for the year 1939. Discoveries were of minor importance except for the Cumberland pool in Marshall and Bryan Counties, in the southern part of the state. Maintenance of a relatively stable producing rate is attributable to the drilling of new wells and the recompletion of many old wells in the previously established producing areas. During the year 1785 new wells were drilled, a decline of approximately 10 per cent as compared with the previous year. Of the wells drilled, 962 were oil wells with a combined initial production of 241,000 bbl. daily, 172 were gas wells having aggregate capacities of 1205 million cu. ft., and 651 were dry holes. Wildcat activity increased 20 per cent over 1939 and 227 such wells were completed during the year; that isl 43 oil wells, 16 gas wells, and 168 dry holes. In addition to the new work completed, 603 wells were recorded as having been drilled deeper or plugged back to test new horizons; included were 334 producing wells with total initial production of 65,000 bbl. daily, 37 gas wells with initial aggregating 305 million cu. ft., and 232 abandonments. Footage drilled amounted to 4,730,000 ft., an average of 2650 ft. per well as com-pared with an average depth of 2600 ft. recorded the previous year. The principal new pools discovered as a result of the exploratory drilling were Cumberland; East Cromwell, in Okfuskee County, and Prague, in Lincoln County. At the end of the year Cumberland had 13 completed wells, which averaged 700 bbl. initial through tubing from the Simpson Bromide formation (Ordovician) at 4750 ft. East Cromwell had 10 wells with average initial of 435 bbl. in the Cromwell sand (Pennsylvanian) at 3460 ft. Prague had II wells with an initial average of 220 bbl. from the Senora sand (Pennsylvanian) at 3260 ft. There were notable extensions to the Dill pool, Okfuskee County, and to the Hewitt pool, Carter County. At the end of the year, 19 producing wells had been drilled in the former, with initials averaging 1000 bbl., and 63 wells averaging 150 bbl. daily in the latter. There were no notable changes in the policy of State conservation authorities with respect to proration. The Bureau of Mines recommendations for the year averaged 413,000 bbl. daily; the State author-ities fixed allowables at an average of 406,000 bbl. daily, while, as noted above, production averaged 409,100 barrels. The most important development in the older areas occurred in the following pools: Billings.—Seven oil wells with an average initial production of 2500 bbl. and two dry holes were completed during the year. Production from the Simpson horizon averaged 6025 bbl. daily as compared with 5950 the previous year. Production from this field has been almost steady since reaching its peak early in 1937. The major portion of the pool is efficiently operated as

Jan 1, 1941

By Thomas Brownfield

Development and production activity in Oklahoma during the year 1940 was of routine nature. Production, according to the Corporation Commission's figures, averaged 409,100 bbl. daily as compared with 421,000 bbl. for the year 1939. Discoveries were of minor importance except for the Cumberland pool in Marshall and Bryan Counties, in the southern part of the state. Maintenance of a relatively stable producing rate is attributable to the drilling of new wells and the recompletion of many old wells in the previously established producing areas. During the year 1785 new wells were drilled, a decline of approximately 10 per cent as compared with the previous year. Of the wells drilled, 962 were oil wells with a combined initial production of 241,000 bbl. daily, 172 were gas wells having aggregate capacities of 1205 million cu. ft., and 651 were dry holes. Wildcat activity increased 20 per cent over 1939 and 227 such wells were completed during the year; that isl 43 oil wells, 16 gas wells, and 168 dry holes. In addition to the new work completed, 603 wells were recorded as having been drilled deeper or plugged back to test new horizons; included were 334 producing wells with total initial production of 65,000 bbl. daily, 37 gas wells with initial aggregating 305 million cu. ft., and 232 abandonments. Footage drilled amounted to 4,730,000 ft., an average of 2650 ft. per well as com-pared with an average depth of 2600 ft. recorded the previous year. The principal new pools discovered as a result of the exploratory drilling were Cumberland; East Cromwell, in Okfuskee County, and Prague, in Lincoln County. At the end of the year Cumberland had 13 completed wells, which averaged 700 bbl. initial through tubing from the Simpson Bromide formation (Ordovician) at 4750 ft. East Cromwell had 10 wells with average initial of 435 bbl. in the Cromwell sand (Pennsylvanian) at 3460 ft. Prague had II wells with an initial average of 220 bbl. from the Senora sand (Pennsylvanian) at 3260 ft. There were notable extensions to the Dill pool, Okfuskee County, and to the Hewitt pool, Carter County. At the end of the year, 19 producing wells had been drilled in the former, with initials averaging 1000 bbl., and 63 wells averaging 150 bbl. daily in the latter. There were no notable changes in the policy of State conservation authorities with respect to proration. The Bureau of Mines recommendations for the year averaged 413,000 bbl. daily; the State author-ities fixed allowables at an average of 406,000 bbl. daily, while, as noted above, production averaged 409,100 barrels. The most important development in the older areas occurred in the following pools: Billings.—Seven oil wells with an average initial production of 2500 bbl. and two dry holes were completed during the year. Production from the Simpson horizon averaged 6025 bbl. daily as compared with 5950 the previous year. Production from this field has been almost steady since reaching its peak early in 1937. The major portion of the pool is efficiently operated as

Jan 1, 1941