Search Documents

By Courtenay de Kalb

THE Exposed Treasure gold-mine has, for the past four years, been one of the largest producing mines of Southern California, its annual output having constituted 1 per cent of the total gold and silver production of the entire State. At the present moment the property is idle, owing to the large quantity of water encountered oil the lower levels, which will require the installation of a powerful pumping-plant before operations can be recommenced. Moreover, a prompt change in the character of the ore has occurred at water-level, which makes imperative an extensive campaign of development in the region of the unoxidized ores before a plant adapted to their treatment can be definitely decided upon. The character of the changes encountered in these deeper ores makes the geology of this deposit a matter of importance, not only for the immediate district, but for the desert region of Southern California in general, where many mines exist having in the oxidized belt conditions that, in many respects, resemble those in the Exposed Treasure mine. The deposit is situated in an apparently isolated butte about 2.5 miles south from the town of Mojave, on the Mojave desert; The butte, though apparently isolated, is in fact geologically part of an extinct volcano, known as Soledad butte, which rises out of the plain 1,5 miles SW. of the mine, to an altitude of 4,650 ft. above sea-level. Other buttes also rise from the desert plain toward the south and east, and again to the westward, all being closely related geologically to Soledad butte,-the whole constituting a single system as to origin and time. Since the end of the period of active volcanism in this region, there has been extensive denudation, the ancient plateau having been dissected during an epoch of apparently exces-

Jan 1, 1907

By Ed Van Eeckhout

As part of a U.S. Bureau of Mines-sponsored project on the utilization of "stiff" backfill to minimize potential rock burst hazards, a finite element study was undertaken to predict stresses and displacements around a stope mined up from the 5400 level of the Sunshine mine, Kellogg, Idaho. This stope was to be backfilled using a high-modulus fill. In preparation for that configuration, certain instrumentation was installed near the 5400 level to monitor stress changes. Due to untenable economics, only 2 cuts of the stope were ever made. This paper presents the results of the instrument readings taken during the first cut and compares them with the numerical predictions, as well as presents the modeling results of closure and fill stresses in the stope if it had been mined.

Jan 1, 1984

By G. M. Wenberg

Bacterial leaching of copper and uranium is practiced in environments containing available sulfur and iron and having a strong acidic reaction. However, many mineral deposits do not have these conditions; the chalcocite and native copper ores in Michigan's Upper Peninsula are examples. Bacterial and fungal populations were observed in samples taken from the White Pine Copper Company tailing pond and mine, and isolates were prepared of the dominant species. The isolates were then screened for solubilization of copper from tailing, ore, and concentrate during incuba¬tion in a carbon and nitrogen supplying medium. Certain Penicillium fungi solubilized significant amounts of copper under neutral to slightly acidic conditions. Leaching apparently was accomplished by release into the medium of metabolites which chelated with the copper.- The process was found to be highly dependent upon the medium and the concentration of copper in the source material. The paper describes sampling and screening techniques, presents the results of experimentation to standardize procedures and maximize the yield of copper, and discusses the nature of the leaching process. This preliminary research reveals a biological process which may find use in mineral extractions but whether it can be applied economically remains to be determined.

Jan 1, 1969

By Ehsan Alavi, Brian Hagan, Glen Frank, Michael A. DiPonio, Michael Mooney, Lisa Mori

"The data from EPB cells located inside the pressurized chamber of EPB TBMs and also the data from the pressure sensors in grout lines are quite important in controlling the EPB operation. However, there have always been questions in regards to pressure distribution along the shield body. Could the pressure distribution data be used to come up with potential locations for ground loss? Does the overcut region, the space between the shield body and the maximum cut diameter, consist of broken material or EPB muck, or does that region consist primarily of void space? During free air interventions, how does pressure distribute along the TBM body? To address these questions, one of the two EPB TBMs used in the Northgate Link Light Rail project in Seattle, WA is equipped with EPB cells in front and rear body to monitor the pressure distribution along the TBM body in addition to the standard 6 EPB cells located inside the cutterhead chamber and pressure sensors located at the grout lines. This paper discusses the results of this study and weighs on the valuable data that can be collected by using the shield pressure sensors.INTRODUCTIONThe cutterhead of the TBM is normally equipped with overcutters on the cutterhead periphery which extend into the annular space beyond the diameter of the TBM shield. Thus, the overcutters serve to disturb and excavate some of the ground in the annular space which reduces friction and resistance around the TBM body. This phenomenon is necessary to help the TBM steer and navigate around curves. Additionally, the shield of an EPB TBM is also often shaped like a cone, with the diameter decreasing from the front to the tail shield. This conical shape also helps the TBM to navigate because material that is cut by the cutterhead either gets pulled into the cutterhead or it gets pushed out of the way – around the cutterhead and into the annular space. In EPB tunneling, the conditioned material from the face that does not get pulled into the cutterhead mixing chamber flows into the shield gap and pressurizes the surrounding ground. Additionally, grout can travel from the segment annulus into the shield gap. The pressure in the shield gap mainly depends on the pressure of the material at the face and the grouting pressure behind the tail shield."

Jan 1, 2016

By J. E. Stukel, J. Cocubinsky

A CONSIDERABLE amount of information is available on the equilibrium distribution of manganese between slag and metal under oxidizing conditions. These data have increased our knowledge of the manganese reactions in the open hearth, ladle, and ingot mold. In contrast, there is a paucity of data on the slag-metal distribution of manganese under reducing conditions. The purpose of the present investigation was to study the equilibrium distribution of manganese between blast-furnace type slags and iron saturated with carbon. Experimental Method Furnace: The induction furnace used for the experiments is shown in Fig. 1. A 1 in. pipe, attached to the transite cover, was fitted with a window through which the charge could be observed. Material could be introduced into the furnace through a tee and plug without removing the cover. A graph-it cylinder (3 in. ID and 10'/2 in. long), centered within the induction coil, was used as a heating element. During a test, a zircon plug kept the top of the furnace from becoming too hot from heat radiation. At the bottom, a graphite block on the vertical center line of the furnace and extending 1 1/2 in. into the coil, was used as a support for the graphite crucibles containing the melt. The graphite crucibles, machined from regular carbon electrode stock, had a 2% in. OD with 3/16 in. walls and were 5% in. long. The fumes present in the furnace during the early part of a run made optical readings uncertain. A noble metal thermocouple was, therefore, adopted to measure the temperatures. The arrangement used, shown in Fig. 1, allowed the silmanite protection tube to be replaced with a minimum effort. The thermocouple was calibrated against a standard Pt-Pt-Rh thermocouple in a fused quartz protection tube. The latter was inserted in the molten iron by removing the glass window on the cover. The lower couple was found to be very sensitive to temperature changes. To insure accurate temperature readings, the graphite crucibles were made to fit tightly against the silmanite protection tube. Further, to avoid contamination of the thermocouple by carbon, the silmanite tube was changed and the calibration procedure was repeated at frequent intervals. By using this temperature measuring technique, the furnace was easily held within *1O°C of the desired temperature. Because of the small free space in the furnace, no attempt was made to control the atmosphere. It

Jan 1, 1955

By Gregory Abramov

Borehole Mining (BHM), a remotely-operated waterjet mining method (Figure 1), has recently achieved two major milestones. It was, for the first time, applied to the extraction of manganese ore and at temperatures below freezing. The 1St stage is a demonstration test that is now underway just north of Emily, Minnesota, where the manganese ore is located 100-160m below the surface and its reserves are estimated to be in excess of 500,000 tons. The deposit was discovered over 60 years ago but, due to the fragile and sensitive nature of this Land of 10,000 Lakes (nickname for the State of Minnesota) and strong environmental restrictions, the iron/manganese reserves were deemed unrecoverable and remained untouched until late 2010 when permission for a single-hole demo-test was issued by the local Department of Natural Resources.

Jan 1, 2011

By Eti Purwaningsih, Widi Astuti, Erik Prasetyo

Selective-reductive leaching of manganese from low-grade manganese ore using tannic acid as a reductant in acidic media was demonstrated by XRD, SEM-EDX characterization, and batch leaching studies at room temperature. The pH change in the liquid phase before and after leaching revealed that selectivity of manganese over iron was due to the hydrolysis of iron. The acidity in the liquid phase during leaching was dictated by two mechanisms: proton-consuming reaction (manganese oxide reduction by tannic acid) and proton-producing reaction (ferric ion reduction by tannic acid to produce ferrous ion). Based on the leaching studies, the more prevalent reaction between these two was determined by initial leaching conditions: tannic acid concentration, sulfuric acid concentration, liquid-solid ratio, temperatures, and agitation time. Kinetic studies revealed that maximum recovery was attained within 6-h agitation, which indicated a product layer diffusion process.

By C. A. Olivier

Le Ministère des Richesses naturelles du Québec has continued development work on the process/or direct reaction 0/sodium carbonate with lithium-bearing silicates(Canadian Patent No. 643,843). Recent process improvements have involved continuous pressure leaching, rather than batch leaching, and higher solution concentrations (over 55 g/l Li2CO3. These improvements have been demonstrated on a pilot scale operating on decrepitated spodumene from the Sullivan Mining Group's Quebec deposit. The new process is expected to be very competitive with the conventional sulphuric acid route. The improved flowsheet and main process steps will be described along with pilot-plant results.

Jan 1, 1979

Jan 1, 1969

Advances in Coarse Particle Recovery - Fluidised-Bed Flotation

Sep 13, 2010

By Matthew S. Sanchez, Richard J. Lee, Matthew D. Zock, Drew R. Van Orden

"Current Environmental Protection Agency (EPA) risk models and asbestos fiber counting techniques for monitoring airborne exposures treat all fibers as being equivalent and ignore the effect of dimension on toxicity. While this may have been appropriate when modern analytical methods were not available, the measurement world is now fully capable of making the appropriate distinctions. The importance of width as a determinant of carcinogenicity has been recognized for nearly 30 years within the published literature. Stanton,1 in a landmark study of a suite of fibrous materials, found that durable mineral fibers with widths less than 0.25 mm and lengths longer than 8 mm were causally associated with the induction of tumors. Pott,2 in a later study, postulated a fiber toxicity model that agreed reasonably well with the Stanton findings, but extended the concept to include varying toxicity as a function of length and width. Wylie et al.3 reanalyzed samples used by Davis et al.4 and found that tumor generation was strongly and inversely correlated with fiber width. Crump5 testified increasing fiber length was correlated with disease occurrence. Lippman6 reviewed a number of studies and suggested that mesothelioma was closely associated with long, thin fibers. Berman et al.7 published a risk model, which found that disease was correlated almost exclusively with fibers longer than 40 mm and width less than 0.25 mm. Recently, Loomis et al.8 reanalyzed textile mill samples and found that aspect ratios greater than 40:1 were highly correlated with disease. Incorporation of width into risk models has been limited by the availability of data from operating asbestos plants and, in particular, the observation of an asbestos plant for which there is no observable mesothelioma. There have been only limited studies published on the dimensions of asbestos fibers, with a few serving as the primary references in other literature.9_13 A rare opportunity to collect detailed concentration and dimensional data of airborne crocidolite from an operating asbestos-cement plant using modern analytical procedures arose, providing a chance to supplement the existing literature on airborne fiber dimensions. The asbestos-cement plant is located in the eastern end of Cochabamba, Bolivia along Highway 4. Cochabamba is a relatively large city located in the Andes Mountains, approximately 250 km southeast of the capital La Paz. The city sits in a valley that runs east-west with mountains to the north and south. The crocidolite used in the products made at this facility is mined in central Bolivia, approximately 75 km northwest of Santa Cruz. The crocidolite is a fibrous magnesioriebeckite 14 (blue asbestos). Crocidolite fibers from Bolivia were the subject of prior reports suggesting the fibers are generally longer and thicker than crocidolite from Australia or South Africa.9 At the cement plant, the run-of-mine crocidolite was first pulverized using a hammer mill and then sieved on vibratory sieves to produce fibers of limited size ranges for use in the cement. The sieved crocidolite is mixed with other components, including recycled cement product, to produce a slurry that is vacuum filtered into sheet form. The sheets are then manually molded into a corrugated shape, air dried, and sawed (using circular saws) to accepted dimensions. The sawed sheets are cured in soaking pits for 28 days before being shipped to the consumer. Prior to shipping, the sheets are finished by a light hand sanding followed (at customer request) by applying one or more coats of paint. A detailed description of the cement plant and the industrial hygiene results can be found in Van Orden et al.15"

Jan 1, 2012

By Carlos Alberto Silva

A aplicação de lubrificação de tiras é um desafio para a maioria das empresas. Aplicações irregulares, não uniformes e excesso de óleo são problemas típicos encontrados quando se utiliza rolos de transferência ou tubos furados. Outros problemas como névoa, baixa eficiência de transferência e um ambiente de trabalho perigoso e insalubre são problemas comuns encontrados com equipamentos que utilizam a pulverização atomizada. O atual trabalho busca comparar os resultados da lubrificação de tiras obtidos com um equipamento de pulverização hidráulica da Spraying Systems frente ao antigo equipamento utilizado, atomizado.

Aug 16, 2017

By Leonard D. Jaffe, Donald C. Buffum

THE importance of temper brittleness in alloy steels has long been realized in Europe, In the United States recognition of its importance has developed within the last several years. Many brittle failures encountered in parts made of alloy steel are undoubtedly attributable, wholly or in part, to temper brittleness. These failures have occurred particularly at low temperatures, under shock loading, and in the presence of notches, restraints and combined stresses. It has been almost universally accepted that plain carbon steels are not susceptible to temper brittleness. As a result, considerable effort has been expended in attempts to discover the manner in which alloying elements introduce temper brittleness. It is desired to raise the possibility that plain carbon steels are not only susceptible to temper brittleness, but are much more susceptible than alloy steels, in the sense that they embrittle much more rapidly. It is suggested that previous views, (that plain carbon steels are not susceptible), are based upon an erroneous interpretation of the experimental results. INTERPRETATION OF PREVIOUS DATA For many years the standard criterion for susceptibility of a steel to temper brittleness consisted of comparison of the energy absorption, in a notched-bar impact test at room temperature, of specimens that had received two heat treatments.1 One specimen (or group of specimens) was quenched, tempered, and quenched from the temper. The other specimen (or group) differed only in having received an embrittlement treatment, which might consist of a slow cool from the tempering temperature, or of an isothermal hold in the range 450-550°C subsequent to quenching from the temper. If the energy absorption of the specimen receiving the embrittlement treatment was lower than that of the specimen not given this treatment, it was said that the steel was susceptible to temper brittleness, If the energy absorptions were the same, it was said that the steel was not susceptible. Several investigators2,3 found that plain carbon steels showed negligible difference in energy absorption in such tests (at least when their manganese content was below 0.60 pct), and concluded that plain carbon steels are not susceptible to temper brittleness. Recently the deficiencies of the criterion mentioned above have been pointed out.4-6 The criterion now generally used for susceptibility to temper brittleness retains the heat treatments used in the earlier scheme, but instead of the notched-bar impact tests being made only at room temperature, they are made over a range of temperatures, covering the transition from ductile to brittle fracture, If the transition temperature of the specimens receiving the embrittlement treatment is higher than those

Jan 1, 1948

By Ren Bryce

The ninth annual Mineral & Metallurgical Processing Division (MPD) student poster contest was held in February at the SME Annual Conference & Expo in Minneapolis, MN. A total of 33 students presented their work at the contest. The competition began in January when the students submitted a one-page abstract for judging. In February, they prepared and presented a poster that explained their research. A panel of judges went to each student and listened as the students explained their research in five minutes. The students worked hard at their research and then set aside time to complete all the necessary steps to enter the contest. The MPD recognizes the effort required to enter and, as a result, provides monetary rewards to all participants. As in past years, there are separate levels of competition for undergraduates and graduates, and the prizes are designated accordingly. At the graduate level, first place receives $1,000, second place $500, third through seventh $200 each, and all others $125 each. At the undergraduate level, first place receives $1,000, second place $500, third place $250, and all others $125 each.

A major problem that has continued to plague the surface coal industry is blast induced damage to the coal seam. Atlas Powder Company has addresssed this situation through seven years of field research in full-scale production environments. Many operations across the United States have been evaluated.

Jan 1, 1990

By Conny Postnpaok, Mark E. Hammele

"A major problem that has continued to plague the surface oil industry is blast induced damage to the coal seam. Atlas Powder Company has addressed this situation through several years of field research in full-scale production environments. Many operations across the United States havebeen evaluated ."

Jan 1, 1989

By John P. Gooch

The Bureau of Mines wrote a computer program which calculates the saturation curves and condensation characteristics of gaseous mixtures consisting of binary organic vapor and air. The program employs an algorithm which assumes an equilibrium mechanism for condensation, and the degree of fractionation obtained is predicted on the basis of relative volatility. The program incorporates a feature which allows the user to examine the fractionation resulting from condensation as a function of the size of the temperature increments over which condensation is assumed to occur. If a single. temperature interval between the dewpoint of the mixture and the outlet temperature of the condenser is assumed for the calculation, the results obtained will be those resulting from a single equilibrium condensation. If the condensation is assumed to occur over a number of temperature increments, the results obtained will approach those predicted by the Rayleigh equation as the magnitude of the temperature increments approaches zero. The results from calculations performed on vapor mixtures from organic heavy liquid solutions used in beneficiating potash and brucite ores are presented. The liquids are solutions of dibromomethane in trichloroethylene or perchloroethylene. The results show the degree of liquid recovery which is possible by cooling mixtures of organic vapor in air. Compositions of the vapor range from 10 to 95 percent air, and assumed condenser exit temperatures range from 110° to 50° F.

Jan 1, 1971

By H. O. Hofman

(Canal Zone Meeting, November, 19]0.) THE sudden decease, April 1, 1910, in Chicago, of Dr. Franklin R. Carpenter was a shock to his- many friends. He died in his sixty-second year, of heart paralysis. To most fellow-members of the Institute who have followed the progress of the. last twenty-five years in the mining and treatment of non-ferrous ores, the work of Dr. Carpenter in that line is familiar ; but very few, even of those who knew him well in the later years, are acquainted with his earlier struggles to satisfy an inborn hunger for knowledge. The story of his life resembles that of the pioneer who opens up new country; overcoming hardships with indomitable courage, meeting doubts and difficulties with an alert and open mind, and exercising in the face of reverses an unconquerable perseverance. It seems appropriate to place on record in the Transactions a brief outline of the life and work of this eminent engineer. During the past 15 years of his life Dr. Carpenter was much interested in genealogy. In the pursuit of this study as an avocation, he traced his own ancestry to the time when ?Hugh," called "le Charpentier" on account of the dexterity with which he had swung his battle-axe as a crusader, settled in Sussex on lands received from William the Conqueror. The Carpenters came to this country with William Penn. A prominent member of the family was Joshua Carpenter, the founder of Christ Church, Philadelphia. Dr. Carpenter's branch of -the family moved from Pennsylvania into that part of Virginia which is now West Virginia, where his grandfather settled in Harrison county, while the grand-uncle went further west, and built the first iron-furnace at Hanging Rock, Lawrence county, Ohio. In fact, since early times, the Carpenters appear to have been iron-masters. Franklin R.. Carpenter was born, Nov. 5, 1848, in Parkers-

Aug 1, 1910

By F. Samimi Namin

During the process of developing surface or underground mines, some sites are considered for dumping of surface soils, while others are applied to reclaiming surface and waste disposal. For each kind of overburden, whether it be waste rock, low-grade material, or process tails, a separate storage site is considered so that it becomes possible to transport or recover the overburden separately. Decision-making must be completed by means of a selection process which takes into account the best methods of alternative sets in order to achieve these goals. This decision- making involves many parameters that are inter-related in that changes in some parameters affect the others. There are many methods of decision-making, however, Fuzzy Multi-attribute Decision-making (FMADM) and its functions are studied in this paper. The advantages of this method lies in its theoretical background, formulation, revising capability, unlimited alternatives, and consideration of the counteraction of the different parameters upon one another.

Jan 1, 2007

By A. L. Hinde

The steady-state and dynamic behaviour of semi-autogenous grinding (SAG) mills are arguably best described using a population model that caters for the breakage kinetics and the material trans-port of rock and pulp inside the mill. Breakage kinetics are usually expressed in terms of a specific breakage rate function and a separate primary breakage distribution function. Material transport usually invokes the concept of a specific discharge rate function. Unfortunately, the breakage rate and breakage distribution functions for SAG mills are very difficult to estimate uniquely from plant data alone. Simplifying assumptions must be made to over-come this problem, which leads to many unresolved dilemmas with regard to whether or not the de-rived functions are accurate, precise, and reflect reality. For example, it is sometimes assumed that the breakage distribution function for a SAG mill treating run-of-mine ore can be derived from laboratory dropweight and tumbling tests on small rocks in narrow size ranges. Such tests hardly reflect the environmental conditions likely to be encountered in a pilot or production SAG mill where there is a wide spectrum of particle sizes. It is shown that the dilemmas associated with standard population balance models (models that utilise separate breakage rate and breakage distribution functions) can be overcome by expressing breakage behaviour inside a SAG mill in terms of a single function. This function is an energy-based cumulative breakage rate function defined as the fractional rate at which particles and rocks coarser than a given size break to below that size per unit specific energy input. A model for SAG milling is formulated, which invokes the concept of a cumulative breakage rate function. Comparisons are made between the mathematical structure of this ?simple model? and standard population balance models. Perhaps the most attractive feature of the ?simple model? is that the cumulative breakage rate function can be uniquely estimated from measurements of size distributions and mass flows of the feed and discharge streams together with the size distribution and holdup mass of the mill charge. Such measurement can easily be made at pilot scale. It is concluded that this simplified approach to SAG milling may turn out to be the quickest way to fully describe and quantify the performance of these very complex mills.

Jan 1, 2014