Search Documents

By Christopher Mark

Severe dynamic multiple seam interactions can occur when active mine workings are subsided by underlying mining activity. The most dramatic events are usually caused by longwall mining or pillar recovery beneath open, overlying entries. But pillars in abandoned workings can also fail and cause subsidence and damage an overlying mine. This paper describes a case history in which an apparent ?pillar squeeze? in the abandoned workings of a lower seam was initiated during retreat mining in an upper seam. The event subsequently extended more than 1,500 ft and ultimately closed the upper seam mine. Analysis indicated that the pillars in the lower mine were adequately sized for the lower seam mining and were not affected by the initial development above them. When retreat mining in the upper seam had progressed several hundred feet, however, the pillars located directly beneath the pillar line were overloaded, and an extensive squeeze initiated in the underlying workings. The squeeze, in turn, subsided the overlying workings, causing widespread rib falls and roof instability. Previous examples of dynamic multiple seam interactions resulting from delayed subsidence of underlying workings have been reported in the literature. This is, apparently, the first recorded incident in which pillar recovery in an active mine triggered pillar failure in an underlying mine, which then triggered a dynamic interaction that impacted the active overlying seam.

Jan 1, 2012

By B. M. England, C. Y. Yang, L. T. Matthews, J. Y. Yin

The domestic concentrate used by the Shanghai Meishan Metallurgical Corporation in Nanjing contains significant siderite, magnetite and haematite, the siderite having a substantial influence on its sintering behaviour. On the basis of experimental findings and published information it is proposed that siderite decomposition starts at c.400 degrees C and results in the formation of CO and/or H2, which then reduces the haematite to magnetite prior to the initiation of high-temperature sintering; inter-mixed particles of Australian haematite and pisolite ores also undergo significant reduction. As the gaseous reduction process is so effective, low-temperature forms of silico-ferrite of Ca and Al (SFCA) cannot form even at high sinter basicity. The bench-scale results were confirmed in a pilot-scale facility whose sinters consisted mainly of magnetite, high-temperature SFCA and glass, which is typical of sinters formed from mixes with high magnetite levels

Aug 1, 1995

By L. D. Smith

"Those who submit competing proposals for projects seek to present senior management with complete and fully supported material that will not fail under questioning. Hopefully, misleading notions and omissions will have been minimized and there will have been testing of the assumptions regarding the economic, social and political environments. A capital project evaluation team can do management and itself a service by including a sound approach to the impact of inflation (and its twin problem, interest) on a project and a great disservice with an inappropriate approach to inflation.InflationHandled deftly, inflation can alter a project evaluation to show almost any result the handler desires. It must be a constant source of frustration for design people and cost estimators to spend weeks perfecting the technical aspects of a project in order to minimize costs, only to have all of their efforts set awash in a sea of financial and economic assumptions that submerge all of the detail. In all of this, inflation is perhaps the largest offender, with inflation criteria often being brought to bear at the last minute, almost as an afterthought. Perhaps this tardiness reflects the difficulty of the subject and the belief that senior management will take its own approach to the problems of inflation. Such a belief is unfair to senior management, for it is entitled to not being misled by omission. It is entitled to the full use of the skills of the evaluating team, including respectable assumptions of the impact of inflation.Working in a consulting context, one has the opportunity to participate in the evaluation of a large number of projects. Reflecting the observation of a wide range of views regarding the subject of inflation, this paper will-address the impact of five different approaches to inflation on the evaluation of a single Canadian mining project."

Jan 1, 1987

By William P. Shinn

Jan 1, 1881

By Ozdemir. O.

Magnesium additions to aluminum enhance strength and hardness, lowering density, and improving corrosion resistance. However, during melting and casting processes, significant amounts of magnesium are lost due to selective oxidation. Preventing these losses would reduce the production cost and improve the quality of the final product. The effects of strontium addition on the oxidation behaviour of aluminum-0.5% and 1% magnesium alloys were investigated by monitoring sample weight gains with time with a thermogravimetric balance at 750°C. Sample cross sections have been examined using Field Emission Gun Scanning Electron Microscope.

Jan 1, 2004

By Kr. J. Dedelyanova

Selective flocculation of iron minerals could improve the economics of high intensity magnetic separation as concomitant process. When the minerals are finely disseminated is necessary a finer grinding to be applied which generates a lot of slimes. The HIMS is not enough efficient for particles below 20 microns ? territory where the selective flocculation is already well known industrial practice, so the combination of these two methods of beneficiation can bring a higher grade at high recovery to be achieved. The dynamics and selectivity of the precipitation process is studied in batch tests with flocculant starch and dispersants sodium silicate and sodium hexametaphosphate. The influence of preliminary conditioning with nitrogen acid at pH 2 before flocculation is also investigated. Flowsheet including these two methods is tested and the distribution of iron is shown.

Jan 1, 2014

By Masaru Imaizumi, Hiroyuki Nomura, Mitsuharu Takita

"Cast iron possesses many superior characteristics caused from precipitated graphite structure, for example, castability, wear resistance, solid lubrication, damping capacity. But the more graphite hyper-eutectic cast iron contains, the lower its mechanical strength becomes, because graphite gives a negative effect to strength of cast iron. In addition, primary graphite tends to segregate during solidification, so uniform materials are difficult to be produced.In this study, authors introduced semi-solid processing in developing new and high quality cast iron. A series of semi-solid processing experiments were carried out to clarify the effect of stirring condition; solidification temperature and etc. on microstructures and characteristics of cast iron. In particular much attention is paid to the appearance of ternary eutectic zone at the final stage of solidification. As the results advanced hyper-eutectic cast iron was obtained with high quality of both the mechanical strength and wear resistance. As for the mechanical strength, 300MPa and 0.60% are obtained as the tensile strength and the elongation values, respectively, under the controlled stirring condition. This indicates that semi-solid processed hyper-eutectic cast iron is used prospectively without spheroidization.IntroductionCast iron has various good properties such as wear resistance, solid lubrication, damping capacity and machinability. The characteristics of cast iron are mainly decided by graphite structure, namely graphite shape and its distribution in the matrix. Mechanical strength of cast iron is large in the case of small quantity of graphite particles which are precipitated uniformly, however, it becomes small in the case of large quantity of graphite precipitated flakily."

Jan 1, 2000

By M. E. Tyrrell

Magnesia spinel (MgO.Al203) recovered from dusting slags in the system MgO.Al203-2Ca0.SiO2 is in the form of single crystals most of which will pass 35-mash. This investigation was undertaken by the Bureau of Mines to evaluate the concentrates as a refractory raw material. Three specific types of refractory bricks were studied: (1) dense, (2) lightweight bubble, and (3) insulating. Test specimens ware fabricated 1 by dry pressing, fired to 1,675° C., and tested by procedures common to the industry. The concentrates produced a refractor, having satisfactory density and mechanical strength; however, spinal is sensitive to thermal shock and the possibility of producing a spall-resistant brick using aggregate of such small grain-size must be considered remote. Lightweight refractorias fabricated of spinel bubbles were the most promising of the types tested. They were 30 percent lighter in sight than the dense refractory, their mechanical strength was good, and definite superiority in thermal shock resistance was indicated.

Jan 1, 1962

By David T. Bunney

In .December of 1987, International Mill Service, Inc. signed an exclusive licensing agreement with Tetronics Research & Development Co. Limited of Faringdon, Oxfordshire., England to commercialize plasma technology which had been demonstrated in an EAF dust processing application. The intent of the process is to reduce and volatize the zinc, lead and cadmium oxides inherent in EAF dust and collect these elements as metals in an ISP (Imperial Smelting Process) zinc splash condenser, and to render the resultant slag an inert, non-hazardous material. With these objectives in mind, IMS started commissioning facilities in 1989 at Florida Steel in Jackson, Tennessee and Nucor-Yamato Steel in Armorel, Arkansas. This paper will address the commercial development and progress of the technology at these two installations. Process Description In the EAF steelmaking process typically the off gas stream is cleaned by some form of baghouse. The particulate collected is known as Electric Arc Furnace dust and has been designated by the U.S. EPA as hazardous waste number K061, once it leaves the collection system. This designation was given to the material due to the high toxic concentrations of lead and cadmium (nickel and chromium for stainless EAF dusts) inherent in the dust. IMS' method of operation is to locate the facilities on the client mill's property adjacent to the baghouse. The dust is transported directly to IMS via a closed conveyance system. This method enables the technology to be an additional processing step in the steelmaking process. Once the dust has been transported to the IMS facility, it is fed, metered and mixed mechanically in the feed conveyance system with a carbon reductant (typically coke breeze). The carbon reductant is approximately 10% of the dust feed rate. This mixture passes through the feed system and enters the furnace

Jan 1, 1992

By George S. Rice

GROUND movement and subsidence is an important matter from several points of view and it is regrettable that more papers have not been written on this subject in the past year. Damage may be done to surface buildings or to the higher workings of a mine, and a study of the subject gives valuable in- formation on hanging-wall or roof control. The latter objective is strikingly shown in a recent paper presented by Jack Spaulding on Oct. 21, 1937, before the Institution of Mining and Metallurgy, of Great Britain, entitled "Theory and Practice of Ground Control in the Kolar Gold Field, India." All may not agree with some of his theories that were deduced from studies of the many violent rock bursts at depths of 5000 to 7000 ft., but the data obtained are of great value. His theories of symmetrical ring stresses and symmetrical domes which are pictured as perfect are rather hard to understand as such uniformity is un- likely in view of the irregularities in the formation due to folds and fractures of various kinds. All will agree in principle with this idea of domal effects, which have been observed in many countries, but they are generally irregular.

Jan 1, 1938

By Hongbo Zhao, Jun Wang, Wenqing Qin, Guanzhou Qiu, Xueduan Liu

Bio-hydrometallurgy technology was applied for the extraction of copper from the raw ores of Chambishi Mine in Zambia. A copper extraction of 93.29% was obtained for small scale column bioleaching within 63 days, while a copper extraction of 89.05% was achieved for large scale column bioleaching in 90 days, thus confirming the amenability of the raw ores for effective extraction via bioleaching. The bacteria were cultured in a 6-stage enlarge cultivation. The bacterial cultures with cell concentration of more than 1×108 cells/mL were added into a spray pond of sulfuric acid to be applied in the dump leaching, and a copper extraction of about 50% was achieved within 2 months. The production report revealed that the copper extraction increased by approximate 20%, and the acid consumption was reduced to around 35% as a consequence of adding the bacteria. The industrial demonstration of the bio-hydrometallurgy technique is now well established in Zambia, and further applications of bio-hydrometallurgy in both Zambia and Congo are currently in progress.

Jan 1, 2015

By G. A. Moruzi

Two sulphide dust secondacy explosions have occurred in the mines of the SUdbury operations of Falconbridge Ltd. during the past 18 months. 'Ihe main similarity between the occurrences is that they both happened in vertical crater retreat blasthole stopes. A relatively high p:,v.tier factor was noted in both instances. other details are enumerated and examined, as well as some results of tests done by Noranda Research on company ore samples.

May 11, 1988

By M. L. Chapman

When originally accepting the assignment, the Client had described the property as vacant land. A prior appraisal was later discovered and revealed that the property included a mineral rights appraisal. Further research disclosed an old dispute with a court ruling based on testimony by AIMA-certified experts. The present appraisal was therefore based on data from findings of the court with a fresh look at discount rate, absorption period, and residual land value. Fortuitously, the property subsequently sold on the market, while meeting all criteria for Fair Market Value. This provided insight into a market-based discount rate. Also, the absorption period could be adjusted in accordance with the current market conditions. The residual land value was minimal (based on comparable sales and projecting trends in market) as the property was affected by a flood zone and the surrounding development was sparse. PROPERTY HISTORY: A GREAT INVESTMENT Briefly, the subject property is located in the floodplain region of the San Jacinto River, a short river in southeastern Texas that flows into Galveston Bay, filled with sand and gravel. This location is on the north side of Houston, north of Beltway 8 on the east side of I-59.

Jan 1, 2012

By David G. Winter

The Olive 8 excavation site in Seattle was surrounded on three sides by conditions requiring innovation, careful modeling, and extensive instrumentation to support use of a first-of-its-kind shoring system. The solution combined heavy soldier piles, long and steeply angled tieback anchors, and tightly spaced soil nails to support surcharge loads from a 33-story adjacent tower separated by a narrow alley housing critical utility lines. Land restrictions on two other sides of the site also required innovative applications of traditional methods. The Olive 8 project has won three state and local awards for innovation and has been reported on in Engineering News-Record and has been the subject of two feature articles in the Seattle Daily Journal of Commerce. This paper presents the conditions and site challenges, reviews the design analysis, discusses the shoring performance, and looks at other potential applications.

Jan 1, 2009

By H. S. Chang

A three-dimension two-phase (air and dust) computer model was developed to model air velocity and respirable dust distributions in the longwall faces. This paper describes the derivation of the model including the model features, mathematical equations and boundary conditions. Example simulations were also performed for two longwall faces where measured respirable dust and air velocity distributions were available. The results indicated the model can simulate the mine conditions fairly accurately.

Jan 1, 1996

By Cordner G. D

Titanium is not yet being produced on a commercial scale despite the facts that it has some impressive properties, and that it occurs very abundantly in easily-mined, highgrade oxide ores. One important reason for this is that the excellent mechanical properties of the metal were not widely recognised and appreciated until about twenty years ago.Another factor which has tended to retard progress in titanium metallurgy has been the realization that the oxide minerals of titanium are very stable; in other words, considerable energy has to be expended to reduce the oxide to metal. Table 1 presents the minimum energies which would have to be expended to produce one ton of each of the metals, aluminium, magnesium, titanium and iron from their respective oxides under theoretically ideal conditions at normal temperature and pressure. At higher temperatures, the minimum energy requirements are different, but the values for the various metals still fall in the same order as indicated in Table 1.In actual fact, the energy consumption in the case of any particular metal is higher than the ideal value by an amount which can be determined only by' the results of plant practice. The only general conclusion that can be drawn from the data in Table 1 is that it might eventually prove...

Jan 1, 1950

By Pedro P. Olórtegui F.

El objetivo del texto es señalar la importancia de las relaciones públicas -en tanto grupo que responde a un interés común- con la industria minera. Las relaciones públicas se dividen en dos campos: relaciones públicas internas y externas. Las primeras, tienen por objetivo mejorar las condiciones del personal y su habilidad en el trabajo a través del gestionamiento de los asistentes sociales, quienes regularán un programa de vivienda, educación y asistencia social que fortalecerá los lazos comunicativos y culturales con el trabajador y la empresa. Los segundos, regulan la relación de la empresa con la comunidad y otras empresas a nivel nacional, asi como con los representantes locales y regionales de la prensa.

Aug 20, 1965

By G. X. Du

Improving reaction effectiveness of asbestos tailings and acid is main means to increase the productivity of magnesium hydroxide and amorphous silica and to reduce production costs. In this paper, the process optimization of acid-leaching reaction process of asbestos tailings is reported. Through the orthogonal experiments of four influence factors, such as acid consumption, reaction temperature, reaction time and initial acid concentration in the leaching reaction. The experiment results indicated that the optimal process parameters were as follows: reaction temperature was 95?, reaction time was 1.5h, acid consumption was 218.9g hydrochloric acid(37%) per 100g asbestos tailings and initial acid concentration was about 25%. The influence significance sequence of the four factors was as follows: reaction temperature > reaction time > mass concentration of hydrochloric acid > hydrochloric acid consumption. Under the optimum process conditions, the leaching rate of MgO was 97.3%, total iron 98.15% and Al2O3 57.9%.

Jan 1, 2014

By K. B. Chaudhuri, I. D. Webb, F. E. Rachor, F. A. Sauert

"A characteristic of all methods of copper concentrate smelting is that slags with a high copper content are produced at some phase of the operation. Recirculation to the smelting unit, electric furnace reduction or flotation are at present used on an industrial scale to recover the copper from these slags. This paper describes the application of the top-blowing technique, originally developed by KHD Humboldt- Wedag AG for refining of metallic copper, for the treatment of copper-containing slags. By this method, a mixture of a reducing gas and commercial oxygen is blown onto the melt at velocities which can be supersonic from the tip of a water cooled lance. The impingement of the reaction gas mixture on the surface of the slag forms a depression in the molten phase and a deflection of the jet which brings the slag into a rotating motion. This causes high rates of heat and mass transfer. Results of pilot-plant tests for batch and continuous treatment of slags are presented, and the potential applications of top blowing for industrial-scale operation are indicated. In combination with the cyclone as a smelting unit, this process appears to be economic for smelters of very low capacity."

Jan 1, 1980

By Rogers F. Davis

This publication has been prepared to supply manufacturers and industrial users a listing of mobile diesel-powered transportation equipment approved or certified by the Bureau of Mines f r use in gassy noncoal mines and tunnels. Testing of diesel-powered equipment is one phase of the Bureau's health and safety program of approval of electrical and diesel equipment designed to prevent explosions, fires, shocks, and toxic hazards in underground mines. In mines such equipment must be used and maintained properly. Manufacturers submit machinery and component parts to the Bureau for study f their design and safety features. Equipment must pass exacting tests and meet strict requirements established through research, development, and experience before the Bureau approves it as permissible for safe use in mines.

Jan 1, 1967