Search Documents

By Yuan Le, Dominic Reda, Vojtech Ernst Gall, Kurt Zeidler, Tomasz Kecerski

High Speed 2 (HS2) mandated that Building Information Modelling (BIM) processes be implemented during design and construction. Gall Zeidler Consultants (GZ) was responsible for developing the BIM Models for the portals, tunnels, and cross passages of the of the 16 km-long Chiltern twin-bore Tunnel. In addition, GZ developed the GBR for the Chiltern Tunnels and incorporated the relevant information into the Project’s BIM framework. This paper presents the implemented BIM framework, describes the modelling approach, and discusses the advantages and challenges of implementing BIM, particularly how BIM improved interface coordination and how BIM was used in feasibility assessments of different construction options.

Jun 13, 2023

By SAM YOUR

PROCESSING, technology and application of non- ferrous metals-copper, lead, zinc, aluminum, nickel, precious metals, foundry metallurgy, less common metals, secondary metals-are the special field of the Institute of Metals Division. New developments in this field during 1930 are more or less briefly out- lined in this review prepared by the papers and publications committee of the Institute of Metals Division as follows:

Jan 1, 1931

By J. Bongarra

This report describes the development of the instructional design and content of a training program for shaft construction miners and supervisors. The recommended training approach is based on the results of a needs, task, and competency analysis of the jobs performed by conventional shaft sinking and raise drill personnel. Learning objectives were derived from the task analysis and the appropriate training delivery system was chosen using a selection technique which employed learning algorithms. The training described is aimed at improving the safety and efficiency of constructing shafts by new hire and experienced miners and supervisors. A self-paced, self-teaching, modular approach to training, using criterion-referenced tests was proposed. Recommendation was made to divide the training into three parts: Orientation and Safety; Task Instruction; and Practical Exercise. Training requirements for conventional shaft sinking and raise drilling were described. Training program content was detailed in the form of module and lesson design approaches. In addition, the report recommends a method for developing, implementing and validating the training program. The authors conclude that such an implementation would meet the major objectives of improving the safety and efficiency of shaft construction work operations.

Jan 1, 1979

By M. M. O?Brien

THE SULLIVAN MINE The Sullivan mine of the Consolidated Mining and ? Smelting Company of Canada, Limited, is situated at Kimberley, B.C., nineteen miles from Cranbrook, a divisional point on the Crowsnest Pass branch of the Canadian Pacific railway. Production started on a small scale in 1900, and in 1914 the mine became the largest lead producer in Canada. In 1925 it was the largest single producer of lead and zinc in the world. Since operations commenced, 4,800,000 tons of ore have been produced from stopes and 170,000 tons from development. At the present time, ore is being mined at the rate of 1,100,000 tons per year, with a yield of about 200,000 lb. lead, 110,000 lb. zinc, and 4,000,000 oz. silver. The town of Kimberley is easily accessible by road as well as by rail. The altitude at Mark creek, a tributary of the St. Mary's river, is 3,700 feet. To th'e north of the creek, Sullivan hill rises to a height of 6,100 feet, and it is on the southern slope of this hill that the mine is located. Sullivan hill is in the Purcell range, which rises between the Rocky Mountain trench on the east and Kootenay lake on the west. It thus lies within what is commonly referred to as the East Kootenay district.

Jan 1, 1926

By Scott D. Neely, Donald R. Clark

"An existing landslide located at the southeast corner of the Telluride Regional Airport has been in an active state of failure for several years. The presence of the landslide has represented an on-going liability for the Airport, the Federal Aviation Administration and the Colorado Department of Transportation. A catastrophic failure of this landslide occurring in a manner similar to that which occurred at the Airport in 1987 has posed an on-going threat to closing Colorado State Highway 145 south and below the slide area. The existing landslide has been characterized as a series of multiple failed block areas located downhill of the airport runway that have occurred in severely weathered Mancos Shale.A total of 12 alternatives were evaluated to mitigate the landslide, including the preferred alternatives of either partial or total landslide removal. However, prior development has left essentially no place on the airport property that would allow for the disposal of the landslide debris for either the total or partial removal alternatives, and the closest off-site disposal area was approximately 40 miles from the site. As a result, in-situ stabilization of the landslide, including a primary system of isolated tie-back anchor plates with strand anchors, and a secondary system of high strength steel mesh and intermediate anchors was selected for the ultimate design of the project to stabilize the landslide in place.For design purposes, geotechnical characterization of the slide area was accomplished through geological mapping, conventional borehole exploration and geophysics using multiple electrical resistivity. The paper discusses the design process utilized and the unique challenges faced one-third of the way through construction when discovery of a survey error required redesign of the entire landslide mass stabilization system using the prefabricated anchors that had already been delivered to the project.INTRODUCTIONTelluride Colorado is located at the toe of the Colorado Rocky Mountains on the western slope. The Telluride Regional Airport is located on Deep Creek Mesa about 5 miles west of the town of Telluride.The landslide is located at the southeast corner of the airport just below an abandoned portion of the quarry access road on a south facing slope. The quarry access road is located below the elevation of the runway and outside the elk fence that surrounds the air traffic area of the airport property. Since the reconstruction of the runway, the access road to the quarry and the construction access road for the reconstruction of the airport runway and safety area were rerouted to stable ground north of the previous access road location and off of the head scarp of the landslide."

Jan 1, 2015

By P. M. Sullivan

At its College Park Metallurgy Research Center in Maryland, the Bureau of Mines has installed and is operating a 5-ton-per-hour pilot plant for continuous mechanical separation of values contained in raw urban refuse. The entire sys tern was assembled using commercially available equipment. The process relies on multistage processing including shredding, air classification, screening, gravity concentration, and electrostatic separation. Compactor trucks deliver raw refuse collected along typical routes in metropolitan Washington, D.C., to the pilot plant. The loads are separated into concentrates of (1) light-gage iron, (2) massive metals, (3) glass, (4) putrescibles and waste combustibles, (5) paper, and (6) plastics. While some refinements remain to be made in the processing system flow-sheet, the data obtained to date have been highly encouraging, indicating favorable economics for commercial-size plants.

Jan 1, 1973

By Xavier B. Starnes

The Dike and Eaton veins in Crittenden County, Ky. (fig. 1), are along northwesterly trending relief fractures that lie between two northeastward striking major faults - the Moore Hill and- the Levias, in Crittenden County, Ky. The veins contain small, narrow, irregular ore bodies of fluorspar with subordinate quantities of sphalerite and galena. Gravel fluorspar was found on the surface in the Eaton vein, and open-cut mining was in progress on the W. M. Conyer property about 1900. Discovery of fluorspar in the Dike vein came much later, about 1933, on the W. H. LaRue tract, but the principal production on the Dike vein started after the discovery of gravel spar in 1938 on the land of the P. J. Gilless estate. Production from the Eaton vein was estimated at 9,400 tons and that from the Dike vein at 15,700 tons, a total of 25,100 tons. A large part of this production was gravel fluorspar from within 50 foot of the surface. Beneath the gravel spar the veins are very narrow, averaging 2 to 2.5 feet in width, and the ore shoots are small. The deepest mine level was 140 feet below the surface, and the deepest shaft 150 foot. Orb was concentrated by log washer or sent unwashed to custom mills at Marion, Ky. about 6 miles distant.

Jan 1, 1950

By Wallace E. Anable

This investigation by the Bureau of Mines was conducted chiefly on Cuban serpentine nickeliferous ores to determine whether these materials would be amenable to direct carbothermic reduction in an electric furnace to produce a low-carbon ferro-nickel. The project was carried out as one of several under a Memorandum of Agreement between the Bureau of Mines and the General Services Administration (Contract GS-OO-B (D)-152l). Two ore samples were received for this investigation. One was a mixture of nickeliferous serpentine from the North Ocujal, South Ocujal, and San Juan claims of the Nicaro Nickel Co. The other sample was a mixture of material from the Ramona and the Lorna Mulo claims of the Cuban Nickel Co. Most of the ore from the Ocujal-San Juan deposits and about 40 percent of the sample from the Ramona-Lorna Mulo deposits were calcined before smelting. The remainder of the sample from the Ramona-Loma Mulo deposits was smelted after drying to about 8 percent moisture. An arc-resistance, selective-reduction smelting technique was employed in these tests. Either bagasse alone or a mixture of bagasse and coke was used for reductants. No flux was used in the furnace charges.

Jan 1, 1957

By W. W. Adams

Because of insufficient funds for printing, the Bureau of Mines was unable to publish its annual bulletin covering accidents at metal mines in the United States for the year 1933. A brief mimeographed summary of the principal statistical data for that year was released to the public late in 1934. Since then reports for 1934 have been received from the mining companies, and in order to avoid further delay in releasing this information to the mining industry and others interested in the prevention of accidents in mining, statistics for both years are presented in this publication with a minimum of interpretation and comment. The fatal-accident rate for the metal and nonmetallic mines (excluding coal mines) of the United States was more favorable in 1933 than in any previous year since 1911, the first year for which the Bureau of Mines obtained reports from the operators. Further progress was made in 1934, when the fatality rate was even lower than that of 1933. On the other hand, the nonfatal-accident rate, which had reached its lowest level in 1932, increased in 1933 and increased further in 1934, although not to such an extent as to prevent the rate for either of those 2 years from being better than that for any year previous to r1931.

Jan 1, 1936

"Integrity tests refer to a variety of non-destructive tests (NDT) whose purpose is to measure or determine the quality and uniformity, and some- times dimensions, of cast-in-place concrete foundation elements. The tests are primarily aimed at detecting zones of poor quality concrete, voids, bulges, and/or necking.The non destructive integrity testing techniques in this section most generally used for drilled shaft testing are based on one of two physical principles - stress wave propagation or nuclear radiation. All of the stress wave methods involve monitoring a deliberately created vibration, usually of very low amplitude (strains on the order of ??). Some methods rely on direct transmission of the signal, while others rely on processing reflections of the imposed signal.The stress wave methods are inherently sensitive to vibrations from other sources, especially at frequencies that fall within the range of interest for the particular test being applied. Construction activity near the shaft being tested; such as: demolition jack-hammering, pile-driving, casing vibration, excavation and movement of track-vehicles are all known sources of interference that might render test data useless. The actual effect of such vibrations will vary with the type of activity, soil conditions and distance from the testing. The test operator must be able to recognize such interference, and the contractor should be prepared to cooperate with the testing personnel by stopping or moving the source of vibration. If this cannot be done immediately, testing should be postponed until the work in question is finished and the vibration source moved or shut down.NDT methods are not suitable substitutes for routine "topside" construction inspection as described in the Drilled Shaft Inspector’s Manual. However, these NDT methods do allow measurements of the quality of concrete placed in drilled shafts, which cannot be made from "topside" construction inspection. They should be considered supplemental to routine construction inspection as they do provide an additional level of quality control."

Jan 1, 2004

By D. S. Burgess

An investigation of the hazard of spillage of liquefied natural gas (LNG) onto water is described. About 2,000 gallons of LNG were consumed in various tests. The initial vaporization rate of LNG following spillage was found to be 0.037 lb/ft2 sec; when the spill was confined, this vaporization rate was moderated after about 20 seconds by the growth of an ice layer on the water surface; when the spill was unconfined, a coherent ice floe was not observed and the vaporization rate was essentially time independent. The maximum diameter (in feet) of the spreading LNG pool was found to be given by 6.25 Wo 1/3, where Wo is the weight of LNG in pounds, Downwind of a natural gas source, time-averaged methane concentrations were given in good approximation by standard air pollution equations. However, peak concentrations were as much as twentyfold higher than average, adding an additional factor to the assessment of hazard. The effect of layering by the cold vaporized natural gas was similar to the effect of a temperature inversion on normal gases in the atmosphere. Small-scale explosions were observed on pouring LNG onto a water surface; no single explanation seems pertinent to all of the incidents observed.

Jan 1, 1970

By Wayne E. Tuomi

The mining industry is faced with a pressing problem; that is, to develop more efficient methods of extraction, handling and upgrading-techniques that will do the job faster and better than ever before. New techniques require new machines, or applications of new and improved materials that can be used to modify and improve existing machine and equipment designs. The traditional approach has been to increase productivity by increasing equipment size. Prognostication indicates that the trend toward larger equipment sizes and capacities will continue as one answer to the challenge imposed by future increases in mineral demands. But what is the limit on the continued growth of equipment size? Until about 1930, there was a very definite limit-a limit imposed by the strength of the steels and the power plants then available. The equipment engineer had come to an impasse: even though it was easily possible, for instance, to triple the size of a bucket, it had become impractical to correspondingly enlarge the boom, the counterweight, and the power plant.

Jan 3, 1967

By Ian Bell, Saman Nouranian, Shahram Tafazoli, Bahram Sameti, Mahdi Ramezani

"Image-based rock fragmentation sensing in mining and quarry applications includes an important rock boundary delineation step, which is commonly referred to as rock segmentation. This paper presents a novel approach to solve this problem, using artificial intelligence. In the proposed technique, priorknowledge of previously analyzed images is encoded into mathematical/statistical models. A set of human labeled images are used as training inputs. These images are used to train neural networksthrough an optimization process. The networks can then be used in real time for rock delineation. "

Jan 1, 2017

"Real-time, on belt analysis of minerals is becoming increasingly important and critical in modern operations, especially in the mine-to-mill. Prompt gamma neutron activation analysis has long been utilised for real-time elemental analysis in bulk materials, with Scantech's GEOSCAN being the instrument of choice in the minerals sector. Working in the minerals space for 15 years, the GEOSCAN has been successfully implemented in a wide range of minerals applications including iron, copper, lead-zinc, manganese, phosphate and more, and it caters for the very high demands and increasing requirements of a contemporary processing facility. An area of focus has been on increasing the analysis frequency to allow for rapid analysis results with the same high degree of accuracy typically expected of the GEOSCAN. This paper discusses the underlying research and technology that has enabled such rapid analysis and presents a range of examples using a thorough statistical approach on real production material, demonstrating achievable accuracy over a short analysis time, and dispelling common myths about the speed of the technique. Potential applications are discussed to conclude the paper.INTRODUCTION Technology and the information it can provide plays a critical role in the evolving modern mineral processing landscape. The importance of technology to analyse various features of ores and concentrates being processed is obvious, and recent years has seen the advance of numerous technologies to provide a variety of real-time measurements on conveyed material flows. From sampling apparatus to particle size analysis to weight and density meters to full elemental analysis, the availability of information enables a variety of improvements in the process leading to improved efficiency and increased revenue. To maximise the potential benefits, access to real-time information is imperative, and rapid updates of information become necessary to make appropriate process control decisions based on the most relevant and up-to-date information."

Jan 1, 2017

By G J. Halstead, R C. Steinhaus

The True Pipe® in-line sampler was developed in an attempt to address the need for a mechanically reliable and correctly designed sampler to suit one-dimensional pressurised slurry pipelines, often found in metallurgical process plants but for which no reliable and representative sampling solution as yet exists.The design, whose operation is based on the principle of symmetry, is described by Dominique François-Bongarçon (2005) with the synchronous opening and closing of relevant valves. It representatively isolates portions of the particulate material stream at predetermined intervals for effective extraction of primary increments for subsequent sample compositing.Theory of Sampling applicable solutions have proven elusive in flowing pressurised particulate material streams, with various attempts to date not having formulated a viable, mechanically reliable and acceptable design.Compliance to sampling theory is critical, and a number of tests were conducted where certain operating parameters were altered to determine their influence and sensitivity on sampling representativeness.The results of the initial series of tests performed on a carefully designed rig are presented, with additional work discussed for necessary investigation in the near future.Getting closer to a robust, economic and correct design for this challenging application in the minerals industry may now not be that far away. Plant management staff will see improved metallurgical mineral balances around their process plants and significantly reduced sampling discrepancies, particularly in tailings applications. Improved quality control is now possible where, due to plant head room constraints, classical cross stream sampling methods cannot be employed.CITATION:Steinhaus, R C and Halstead, G J, 2014. True pipe sampler – a correct design utilising the principle of symmetry in pressurised slurry particulate streams, in Proceedings Sampling 2014 , pp 127–134 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By Patricia A. Wells

In the remelting of scrap, the ultimate goal is to produce clean aluminum while minimizing metal losses. Recently, it has become more difficult to make significant recovery improvements in Reynolds' Reclamation Plants since metal recoveries were nearing the theoretical maximum. In an effort to gain a better understanding of the factors impacting Reynolds remelting process, a series of experiments using a Taguchi-type design was performed. Specifically, the critical variables and interactions affecting metal recovery of shredded, delacquered Used Beverage Containers (UBC) melted in a side-well reverbatory furnace were examined. This furnace was equipped with plunger-style puddlers and metal circulation. Both delacquecing and melting processes operated continuously with downtime only for necessary mechanical repairs. The experimental design consisted of an orthogonal array with eight trials, each using nominal 500;000 lb shred charge volumes. Final recovery results included molten output and metal easily recovered from dross generated during the test.

Jan 1, 1995

By A. H. Duffield

"Forming part of the Prairie Evaporites, the sylvinite layer mined at Alwinsal underlies the Blairmore quicksands and the water-bearing Devonian formations. Production is achieved by a method of trackless, continuous mining of rooms, leaving pillars for natural support. The paper describes the development of the mine, and the equipment and organization employed in the operation and maintenance of the underground facilities."

Jan 1, 1972

By Marco Quirion

The Daniel-Johnson dam, formerly named Manicouagan-5 (Manic-5), is located 800 km northeast of Montreal (Quebec) in Canada. This is the largest multiple-arch concrete dam in the world consisting in 13 arches and 14 buttresses. Since its construction in 1969, various type of cracks have appeared on both downstream and upstream faces of almost all the arches of this concrete dam. As a part of the Daniel- Johnson’s dam safety assessment program, Hydro-Québec is currently performing structural analysis of the dam with advanced numerical models to better understand and predict the dam behaviour. Because the buttresses transmit all the arch loads to the rock mass, determination of the properties of the dam foundation should not be neglected in dam global safety analysis and also to insure that reliable input parameters are used in the dam numerical simulations. This paper summarizes the past and the more recent investigations of this foundation used to assess its safety and stability. Moreover, the use of rock mass classification to estimate the deformation modulus, based on empirical equations, gives values in the range of 30 to 40 GPa that are higher than expected values. Using those values in the numerical simulations for dam structural analysis gives an excellent correlation with displacements monitoring of the buttresses.

Jan 1, 2015

By Ronald H. Church

The Bureau of Mines tested & ground penetrating radar (GPR) system in the central Florida phosphate district. to determine the feasibility of utilizing GPR technology for subsurface cavity detection. The test area is located in karst topography where sinkhole development is prevalent. State regulations require subsurface drilling of damsites to identify underground anomalies; however, this method is not totally accurate in locating subsurface cavities that could lead to sinkhole development. An electromagnetic method of identifying anoma-lous subsurface conditions could reduce or eliminate the possibility of dam failure due to sinkhole development. The Bureau devised a GPR system that successfully penetrated over 50 ft of overburden and gave recognizable radar return signals characteristic of a rock-cavity interface.

Jan 1, 1986

By Josh Savit

Corporate responsibility already encompasses safety and compliance. No longer will companies be able to use differing standards of care to miners based on the country in which they are working. This is not only an issue of social license, but one of global risk management.