Search Documents

By Loren R. Anderson

This is an Appendix of Volume I. In contains the results of the electric cone penetrometer soundings from the second phase of the testing program.

Jan 1, 1982

By AIME AIME

IN accordance with the provisions of Art. XII, See. 3, of the By-laws of the American Institute of Mining and Metallurgical Engineers, the Board of Directors hereby give notice of their intention to amend the By-laws as follows : Art. V, Sec. 2. Amend by substituting the word "senior" for ('first" before the words "Vice-president" in line two of the third paragraph of said section which relates to the calling of special meetings of the Board in the absence or disability of the President.

Jan 1, 1930

Jan 1, 1923

By R. S. Shoemaker, R. M. Darrah

Expanded markets for copper in the past few years and a consequent search for new ore bodies have revitalized the widely known but seldom applied method of producing copper called heap leaching. Heap leaching is defined here as the process applied to oxide ores which have been mined solely for the purpose of leaching. In this case, all costs of mining the ore become a part (and a substantial one, as will be shown) of the cost of the copper produced, whereas in dump leaching the mining cost has already been accounted for as a stripping cost for the sulfide ore. Of course, with newly opened ore bodies, stripping costs may be divided through accounting procedures, between the copper produced by the mill and that obtained by leaching, but in general this type of operation must be economic on the basis of the sulfide ore alone. Heap Leaching Requires Low Capitalization Heap leaching, as a beneficiation method, is unique in that it is the only process used for the recovery of a metal in which the time involved from mining the ore to metal production is measured in months instead of hours or at the most, days. Then too, after the ore body has been depleted and mining has ceased, metal production will continue for some substantial period of time. Heap leaching is also unique because unlike any other method of beneficiation, metal recovery cannot be accurately forecast ahead of time and recovery will never approach that of a conventionally milled sulfide ore or even that of a vat leached oxide ore. Counter-balancing this drawback, however, is the relatively low capital expenditure necessary to put a heap leaching operation into production and the consequence that smaller ore bodies which would not support the higher capital cost involved in a vat leaching plant can be made into producers. Stated more simply, in heap leaching the operator accepts low recovery in exchange for low capital costs and low break even point. Whether the operator chooses vat leaching with its higher recovery and higher capital costs, is a mater of economics which depends in part on the nature of the ore to decide. For instance, an ore that will vat leach in 7 to 10 days using 7 pounds of sulfuric acid per pound of copper produced might use double or triple that amount of acid during the months that are required for heap leaching.

Jan 12, 1968

By Richard J. Kolada, Ian R. Muirhead

"This paper reports on a CANMET-funded examination of less conventional underground coal mining methods. These methods are documented and those that show the most promise for application to western Canadian conditions are discussed in detail.IntroductionIn recent years, mining considerations and economics have encouraged a transition from underground mining to surface mining. However, a change in market conditions or the development of superior underground mining methods may reverse this trend . Should this happen, the industry must be quick to respond and have information available on the latest developments of underground mining technology. In time, deposits of high-quality coal, which are easily accessible to surface mining, will be depleted and a change to underground mining methods will require consideration. The economic transition point between surface to underground will be a major determinant in maintaining a competitive edge. For these reasons, it is important to keep abreast of improvements in underground mining methods. To meet this objective, CANMET awarded a research contract to Monenco Consultants Limited, to investigate unconventional underground mining methods that show a potential for western Canadaoi. This paper presents the results of this investigation."

Jan 1, 1988

By G. Sachs

X-RAY analysis and single-crystal study have been utilized in recent years as a new means of following constitutional changes in alloys. If such transformations can be suppressed by rapid cooling, they can be followed at room temperature in a particularly convenient manner. In the following we shall consider changes in solubility and polymorphic transformations with particular reference to phenomena of the age-hardening type. Finally a thermodynamic viewpoint is developed for examining such transformations.

Jan 1, 1931

By W. R. Hopkins

Over 95 percent of the world's refined copper is now produced by electrolytic processes. The bulk of this electrolytic copper comes via the conventional route for sulfide ores of concentration, smelting and electro-refining. A rapidly increasing percentage of world production is now achieved using hydrometallurgical routes involving dissolution of the copper values from minerals, purification of the resultant leach solution by solvent extraction and finally deposition as cathodes by electrowinning. The technology can now be considered mature and this paper endeavors to summarize recent developments which, from the authors' perspectives, are important.

Jan 1, 1989

By J. F. Edwards

In situ extraction of copper through borehole injection presents a new technology for the mining of copper. For the successful application of this technology, copper recovery at the surface must be specifically designed for borehole injection and the general conditions of the well field. This paper describes the design of a solvent extraction / electrowinning facility specifically designed for in situ leaching of copper. This design is based on commercial solvent extraction / electro-winning with considerations of the requirements of this specific application.

Jan 1, 1988

By S. H. Williston

IT is not often that bore hole surveys can be checked by actual civil engineering methods. A recent Arizona survey was checked by normal surveying methods and the comparison of the results should be of value to both oil and mining men. During the summer of 1948 the Phelps-Dodge Corporation, at its Copper Queen property near Bisbee, Ariz., drilled a 1245 ft, 8 in. diam, churn drill- hole in a mineralized area and cased part of it, intending to use it to transfer mill tailings for stope fill. The hole, as frequently occurs, was not straight, and, in endeavoring to locate the bottom in- the underground workings, they found no evidence of the hole at the underground coordinates directly below the surface location. The noise of the drilling tools was reasonably clear, but the direction of sound was uncertain. Preliminary tests with available equipment were not successful in locating the bottom of the hole. Be- cause of the mineralized character of the area and the fact there was some casing in the hole, any magnetic method of well surveying would give results ' of doubtful value.

Jan 1, 1950

By C. Denis Thibodeau

Outline Introduction 402 OB Mining Sequence Trial to Verify Sequence Change Monitoring Observations Numerical Modelling Conclusion

May 1, 2013

By AIME AIME

THE complete list of papers for the meeting of the Petroleum Division that is to be held" at Tulsa,' Thursday and Friday, Oct. 3 and 4,, with assignment to individual sessions is given below. THURSDAY MORNING First Session Well Spacing Theory of Well Spacing-By W. P. Haseman. Discussion by S. C. Herold, J. R. Suman and Lester C. Uren. Well Spacing in the Long Beach Field, California-By - Stender Sweeney. Discussion by C. H. McNeese; R. R Brandenthaler and W. V. Vietti. Well Spacing in the Bradford Field, Pennsylvania-By Paul D. Torrey. Discussion by A. F. Melcher, R. M.. Haskell, J. B. Umpleby and J. B. Newby. Results of Different Well Spacing in the Salt Creek Field, Wyoming-By Fred E. Wood. Discussion by Sam Grinsfelder and Kenneth B. Knowles.

Jan 1, 1929

By AIME AIME

TECHNICAL achievement in mining will be rewarded at the forthcoming Annual Meeting of the Institute when the William Lawrence Saunders Gold Medal will be presented to Herman C. Bellinger. Mr, Bellinger was unanimously selected on the first ballot of the Medal Committee. Mr. Bellinger has had notable technical success as vice-president in charge of operations for the Chile Exploration Co., a position he has held since 1920.

Jan 1, 1941

Jan 1, 1903

By Stan Henning

The monthly summary of the climatological record for the demonstration mine is presented in Table 1. Tear normal temperatures occurred throughout the growing season. From May to October precipitation was more than normal except in June when it was 2.55 inches below normal. Corn and soybean plantings were delayed until June 2-7 because of wet field conditions. This is about one month later than normal for corn planting. Insect infestations were much less than those encountered in previous years. Cutworm activity was not noticed and alfalfa weevil infestation were small and patchy. Stalk rot in corn was a significant problem at harvest and resulted in much Milk lodging. The wet and generally overcast conditions of July, August and September were bend 10 beneficial al to certain plant disease organisms. For example, pumpkins planted in a small garden area at the demonstration mine did not ripen because of a powdery mildew resulting from overcast, wet conditions. Field operations and row crop plantings were greatly delayed by wet field conditions. It was difficult to plant by conventional tillage because the soil remained soft and sticky where the moldboard plow had been used. Plots in the no-tillage system could he planted before conventionally tilled plots could be traversed. Plant emergence and plant density at

Jan 1, 1982

By Lv Guozhi, Niu Liping, Shi Guanyong, Liu Yan, He Jicheng, Du Yanjun, Dou Zhihe

"We proposed thermit reduction-electroslag remelting method of preparing the large scale CuCr alloy. But there are pores and oxide inclusions in CuCr alloy prepared by thermit reduction process. This paper studied mainly the effects of ratio of reactant and additive on the inclusion type and their occurrences in CuCr alloy. The alloy prepared in different process conditions was characterized via XRD, SEM, OM and TEM and metallographic microscope, in which the existing state and micro-structural defects of inclusions are analyzed. The results show that there are three distinct regions: copper-rich regions, chromium-rich regions and the inclusion regions. Inclusions are mainly in the form of stomata and Alz03 phase, mainly locating in the copper-rich phase and the interface area of chromium-rich phase and the copper-rich phase. Adding Na3AlF6 and heating agent can effectively reduce the inclusion content in the alloy.1 IntroductionIn recent years, with the development ofhigh power vacuum and high-pressure technology ,the CuCr alloy contact material which has many advantages gradually replaced the traditional W-Cu and Cu-Bi series alloy contact material, and become the first choice of material in high-voltage and high-power vacuum switch contacts['-3l. The traditional powder metallurgy method, infiltration method and vacuum arc melting method[4-SJ are using metal Cu powder and Cr powder as raw material by casting molding, and have disadvantages such as high production costs, complicated process, poor product density and low yield, especially in the large size alloy ingots[9-12l. At present, the world regards CuCr alloy new preparation technologies as the first place, and how to achieve a large size the CuCr alloy ingot preparation has become a hot research of CuCr alloy[3l. Zhang Ting-an and Dou Zhihe[l-3l who are supported by national natural science fundation of china successfully successful developed new technologies and core equipment to prepare large-size copper-chromium alloy through aluminum thermal reduction-secondary refining method, and obtained two national invention patents. The method includes two key steps: one is get CuCr alloy consumable ingot by Thermit-SHS with electromagnetic stirring, the other is to refme the CuCr alloy ingot to remove the pores, inclusions and other defects by electroslag remelting technology to get dense and uniform CuCr contact material. The preliminary study results show that means of electromagnetic stirring evidently inhibit effect of alloy ingot macrosegregation during the electromagnetic casting stage, but there are still microstructure defects such as alumina inclusions and pores in the alloy ingots. Therefore, Zhang Ting-an et al refer new ideas of using the electroslag remelting to refine Cu Cr alloy ingots and effectively remove the defects of the ingots such as pores and inclusions [3l _ At present, there is no report of study on the electroslag remelting refining processes of CuCr alloy (the refining slag, remelting current). This article will research mode of occurrence and distribution law of inclusions in the large-size CuCr alloy ingots by Al Thermit-SHS under magnetic field stirring action and provide a theoretical basis for chosing refining slag to remove inclusions by electroslag refining. Meanwhile the article analyses the effect of reduction conditions of Thermit-SHS on the types of inclusions, mode of occurrence and distribution of regular inclusions in alloy ingot, and refer theory for inclusions regulation in the large-size alloy ingots."

Jan 1, 2013

By Mairyanne S. S. Souza, Sergio Neves Monteiro, Victor Tomazinho Bartolazzi, Dienifer Daiana Konzen

Clay is used in the production and manufacture of materials for the construction of buildings from remote periods. Advances and improvements of its properties have allowed several applications to this raw material. In this work the quality of four types of ceramic tiles manufactured or used in the northwest of the state of Rio de Janeiro and in the southeastern state of Minas Gerais was evaluated. Geometric, physical and mechanical aspects were evaluated according to the Brazilian standard NBR 15310:2009. The results indicate numerous nonconfor- mities with highlights for geometric parameters, surface flatness and yield tests. The nonconformities found in the samples indicate that there was a failure in the production control of the product and in the approval of the control of the lots.

Mar 1, 2018

By S. K. Oraee

Most management decisions at all levels of the organization are as directly or indirectly depends on the circumstance of future. With regard to predict the future events in the process of decision-making plays a main role, therefore, forecasting is very important for every organizations and institutions. There is a variety of methods to predict time series. In general, these techniques can be divided as following: statistical, artificial intelligence and analytical techniques. Two of the most common methods for time series prediction is autoregressive integrated moving average (ARIMA) and artificial neural network (ANN) methods, these methods are the subset of statistical and artificial intelligence techniques respectively. In this paper, a hybrid model of ARIMA and ANN models are employed to predict the number of fatal injuries in the USA underground coal mines. This research showed the result of hybrid model is better than split model.

Jan 1, 2011

During the extensive research which has been conducted in the Metallurgy Department of the University of Melbourne, into the properties of lead and its dilute alloys, the Brinell test has been used for the determination of hardness.The work described herein represents part of an investigation into the influence of various factors on such determinations, particularly when carried out on different qualities of "pure" lead. It is intended to publish the more theoretical and controversial aspects of this research elsewhere.MATERIALS USED AND THEIR PREPARATION FOR TESTINGThe tests to be reported have been conducted on a specially pure electrolytic lead, and several brands of commercially "pure" lead. The analyses of the samples upon which most of the work has been carried out are given in Table 1.Note: Oxygen was not determined, but from the work of H. W. Worner, in the Rosenhain Memorial Laboratory, it appears probable that it was approximately 0-0003% in all samples.

Jan 1, 1940

By M A. Knackstedt

Coupling between deformation processes and rock permeability is a major factor influencing the architecture of fluid migration and the localisation of ore deposition in several types of hydrothermal ore systems in middle to upper crustal regimes. Permeability in many hydrothermal systems is controlled by a dynamic competition between deformation-induced porosity-creation processes and porosity-destruction processes. Localisation of deformation within faults, fractures and shear zones leads to flow localisation, with large-scale flow systems forming when active faults and shear zones link to create percolation networks. Numerical modelling techniques are used to explore the growth of fracture networks and evolution of network connectivity during progressive deformation. Initial results indicate that networks reach a percolation threshold at very low strains. Near the percolation threshold, flow is localised along a small proportion of the total fracture population and favours localised ore deposition. At higher strains, flow is distributed more widely throughout the fracture population and may provide reduced potential for production of high-grade deposits. The distribution of mesothermal gold deposits along a small subset of the total population of co-active faults and shear zones in the Archaean Yilgarn Craton in Western Australia indicates that some hydrothermal systems maintain themselves near the percolation threshold for a substantial part of the lifetime of the system. Fluid-driven growth of fault/fracture/shear networks may lead them to self-organise near the percolation threshold.

Jan 1, 1999

By Lyman G. J

Dense medium drum separator efficiency was analysed at two Western Australian iron ore concentrators. Efficiency data had hitherto been difficult to accumulate due to the high cost of analysing representative, and therefore large, coarse ore samples. To overcome this problem, recoverable density tracers, which are in effect artificial mineral and gangue, were manufactured in three different sizes (15 mm, 30 mm and 60 mm). Their use enabled partition curves to be studied within one hour of conducting a test: separation densities were generally lower than the feed medium density for all three sizes of density tracer. For a given set of operating conditions, the smaller tracers had lower separation densities and larger ecart probab/es than the large tracers. These phenomena are explained with the aid of a conceptual model of a drum separator, which assumes that the feed ore plunges to the bottom of the drum upon introduction. Particle rising velocities are, therefore, process determining.Medium rheology was altered by adjusting the proportion of solids in the pulp. This was accomplished by changing both the pulp density and ferrosilicon/magnetite ratio. Higher solids volume fractions invariably caused a decrease in separation densities and an increase in ecart probables, most markedly for the smaller tracers. A similar response was observed when feed tonnages were raised.An explanation for these phenomena is sought in the discussion which also suggests means of improving drum separator efficiency.

Jan 1, 1987