Search Documents

"In the mines producing over 500 tons per day, skips have replaced the old method of hoisting ore by cars run onto cages. In the car and cage method, two men (station tenders) trammed the loaded cars onto the one-deck cage, and as the production increased the one-deck cage was increased to two decks and later to four decks. Landing chairs at the underground stations were necessary in this method and were the cause of many serious accidents by being carelessly left in the shaft by the station-tenders when leaving one station for anotherabove. The labor and time occupied in loading the leaving cages were con¬siderable, and, at times of rapid hoisting, four men were necessary in taking off empty and caging loaded cars. This also required at the surface landing, as many as ten men on a shift to remove the loaded cars and replacing them with empties, and tram the loaded ones to the surface ore bins, where the railway cars were loaded.The skips used in Butte are generally of 100 cubic feet capacity and hold five tons of ore, and weigh 7,500 lbs. The cage above, to which the skip is attached, weighs 2,300 lbs. The skips dump automatically into a pocket of 50 tons capacity. Two men are with the skips underground and load them from 125 ton capacity ore-pockets, under each station, the bottoms of the pockets having an inclination of 50 degrees from the horizontal. At the bottom of these pockets a gate is operated by compressed air. The labor of loading the skips amounts only to the opening and closing of a valve in the air-line, the ore running by gravity into the skips.Besides the saving in labor, the use of the skips has removed the necessity of underground landing chairs in the shaft and the accidents which are inevitable where such chairs are used."

Jan 1, 1913

By Osmar de Sousa Santos

NiTi shape memory alloys (SMA) have been widely used as construction materials due to their shape memory and superelastic properties. Usually the application of the NiTi alloy is in the wire form, which is ideal shape to make springs, orthodontic arc-wire and endodontic files. Since our research group (ITASMART) started producing NiTi wires, it was noticed that NiTi SMA produced by Vacuum Induction Melting (VIM) presents carbon contamination, which is due to the melting process. Therefore, alloys rich in carbon remove titanium from matrix, forming precipitates of TiC (titanium carbide). Also, Ti2Ni precipitation removes titanium from the matrix and these two precipitates TiC and Ti2Ni can produce internal volumetric defect in the wire drawing process. Seeing the importance of NiTi wires as base of many applications, this work studies the formation of volumetric defects caused by precipitates in the wire drawing process of a NiTi wire drawn down to 0,39 mm in diameter.

Aug 8, 2018

By Yongyong Gong, Qijie Zhai, Zhichen Zhang, Qixin Li, Zhishuai Xu

"Microstructure of semisolid slurry of Al-4.5wt.%Cu alloy was investigated with pulse magnetooscillation (PMO) treatment, the results showed that the PMO treatment can refine the crystal structures of Al-4.5wt.%Cu alloy significantly. The discharging frequency of PMO had a great effect on the solidified structure transformation of semisolid slurry of Al-4.5wt. %Cu alloy, and the primary a-Al particles become much finer and rounder with an increase of discharging frequency. However, over a certain discharging frequency, the grains of primary a-Al become coarse.IntroductionOver the last decade, a lot of attentions have been paid on metal rheoforming process [1-4], since it has higher mechanical properties of formed components, strength to weight ratio and age hardenablity. Nevertheless, semi-solid forming is always performed at high solid fractions (40%-60%), so it has the limitation of viscosity, a tends to be difficult to pour semisolid slurry into the hole of the shot sleeve. Therefore, a series of novel semi-solid slurry preparation methods and rheoforming techniques have been invented, such as, semisolid vibration treatment [5], rheocasting [6], pulsed magnetic field process [7], annulus electromagnetic stirring [8], via ultrasonic vibration process [9], equal channel angular extrusion (ECAE) process [l0] and straininduced melt activation (SIMA) process [11].The electromagnetic field is characterized by its effective grain refinement, green, convenient manipulation and without contamination of melt. The mechanisms of dendrite was fragmentation by electromagnetic field have also been largely proposed [12-14]. The broken dendrite arms then undergo a coarsening process to provide the globular structures and obtain much finer and rounder a-Al particles. When compared with other external electromagnetic techniques, Pulse Magneto-Oscillation (PMO) has obtained more fuvors, owing to narrower pulse width and much lower energy consumption. Furthermore, the PMO treatment can reach finer grains with shorter time treatment [16, 17]. This work aims to study the effects of different discharging frequency ofPMO treatment on the microstructure transition of the semisolid slurry of Al-4.5 wt.%Cu alloy."

Jan 1, 2014

By Lisa E. Helberg

"Titanium tetrachloride is produced through the chlorination of a variety of titanium bearing ores, some occurring in nature, and others enriched in titanium content by a variety of ""beneficiation"" processes. The chlorination step can produce a variety of metal chloride impurities, such as iron chlorides and vanadium chlorides, which must be removed from the TiC14 before it can be used to produce pigmentary TiO2, titanium metal or for any other commercial use. The requisite manipulations involve both physical and chemical separations in a multi-step process. The history of various purification strategies will be discussed.TextThere are a wide range of titanium-based products available, all of which start with titanoferrous ore of some type. Two main routes are used to convert ores into products, known as the sulfate and chloride processes. The sulfate process uses sulfuric acid to digest the ore, separate the impurities, and then precipitate titanium dioxide from the resulting titanyl sulfate (TiOSO4) via metatitanic acid. This process can also supply TiOS04 for other applications."

Jan 1, 2011

By F. G. Prado

The technology for the extraction of zinc from zinc residues, such as zinc ashes, drosses and metallurgical flue dusts, by way of ammonium chloride solutions is well established, at least at the laboratory and bench scale levels. (3, 4) Zinc is soluble in ammonium chloride solutions in the form of zinc diammine chloride. Its solubility depends upon the concentrations and temperatures employed. The procedure and the equipment required are simple, and they can be applied either to small or large operations. As a by-product, zinc diammine chloride is produced with extremely low impurities in quantities which are stoichiometrically proportional to the zinc removed. The technology has been applied experimentally to galvanized steel residues. The dezincing results, including removal performance, energy and reagents required, and by-products are summarily presented in this paper.

Jan 1, 1992

By J. E. Murphy

The high-purity thorium metal was prepared by the Bureau of Mines from electrolytically produced thorium alloys. The thorium-chromium and thorium-manganese alloys were separated into the component elements by vacuum distillation. Chromium and manganese impurities remaining in the thorium metal after distillation at 1,850° C were <0.005 weight-percent. Removal of volatile impurities such as aluminum, calcium, magnesium, and lead was also accomplished.

Jan 1, 1969

By Z. D. Tan

The continuous digestion technological conditions of phosphate tailings with high magnesium content in sulfuric and phosphoric mixed acid is studied in this paper. The influences of excess coefficient of sulfuric acid, weight liquid to solid, reaction temperature and time on conversion of P2O5 and MgO are discussed. The influence of infiltration capacity of phosphogypsum by the concentration of liquid-phase SO3 is discussed too. Under the optimal technological conditions, the conversion of P2O5 is 95.56% and MgO 98.63%, the filtration rate of phosphogypsum increases with the increasing of liquid-phase concentration of SO3, the optimal apparent concentration of SO3 is 0.135~0.14g? mL-1 in liquid-phase. The filtration rate of phosphogypsum is 1473kg? m-2? h-1. N-P-Mg compound fertilizer was produced by adding magnesia powder and inflating ammonia in filtering medium.

Jan 1, 2014

By B. R. Bowerman, W. J. Thoburn, M. J. Humphris

"Nickel granules are produced for carbonylation by pouring a molten stream into a path of high pressure water. Granules and water are separated in dewatering bins. The overflow, which contains up to 0.1 weight percent solids, was initially cooled and recycled to the granulating step. However, the rate of buildup of these solids in the handling system was intolerable. A lamella thickener was installed to solve the problem by removing solids from the dewatering bin overflow. Its description, application and performance to date are discussed.The lamella thickener treats a slurry containing about 0.1% solids of which about 30 weight percent is less than 325 mesh. It recovers 80 to 90 percent of the input solids in an underflow slurry containing 90 weight percent solids. Since its installation the frequency of cleanout of the recycle water handling system has dropped from about once per month to about once or twice per-year."

Jan 1, 1977

By Bingyi Bai, Wangjun Peng, Yanling Guo, Jieyu Zhang, Guoding Gao

The phase transformation of bayan obo ore with high concentration of iron and calcium was reduced at temperatures no more than 1000℃ were investigated in this study. The samples with insufficient carbon were treated at the temperature using a vertical furnace with a thermogravimetry (TG). The mineral phases and content were examined using Xray diffraction (XRD) and X-ray fluorescence spectroscopy (XRF) respectively. The complex phases of bayan obo ore transformed to some simple phases after treated with different content of carbon at the same temperature for 10 hours. The result of XRD、 XRF and TG showed that the reduction degree of Fe3O4 phase formation varied with the temperature and the carbon content of bayan obo ore.

Jan 1, 2015

By Xiaolong Lin, Yuanbo Zhang, Jiann-Yang Hwang, Guanghui Li, Hongjin Zhang, Jiaxing Yan, Zhiwei Peng, Tao Jiang

The pollution caused by the spent printed circuit boards (PCBs) is currently a concern of researchers and environmental managers due to its large quantity and exceptionally complex properties. This study characterized printed circuit boards (PCBs) from discarded computers using a number of characterization techniques, including chemical analysis, X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), granulometric analysis and scanning electron microscopy (SEM).The PCBs contain approximately 50 wt% metals, 25 wt% glass fibers and 25 wt% polymers. The principal metals include copper, calcium, tin, aluminum, zinc and lead. They are still wrapped by brominated epoxy resin after the PCBs are preliminarily crushed. As precious metals, such as gold and silver, are barely found in the PCBs, copper and tin are the main metallic elements of recycling value which warrants extra attention.

Mar 1, 2017

By Pan Gu, Zhen Zhang, Wen-Feng Tan, Jiang Diao, Bing Xie, Wang Zhou

In order to recover the chromium resource in chromium-containing vanadium extraction residue, a promising method is to prepare ferrochromium with the residue. The synthetic residue has been reduced under 1300, 1350 and 1400 °C at the reduction time of 1, 2 and 3 h respectively. The reduced samples have been smelted and separated by an induction furnace. The contents of chromium and iron in metallic phase have been determined by an inductively-coupled plasma spectrometer. The results indicate that chromium iron carbide (Cr, Fe)3C7 is the intermediate phase and titanium oxides have been reduced during the reduction process. While the sample has been reduced under 1400 °C for 3 h, metallic phase becomes the dominate phase and reduction reactions almost complete. Moreover, the chromium content in the metal phase reaches 10.19%.

Mar 1, 2017

By Gray Mullins

This paper presents results from model and full-scale tests to assess the interface bond between a cast-in-place concrete seal slab and steel H-piles in cofferdams. Three different seal slab placement conditions - fresh water, salt water and bentonite slurry - were evaluated and the results compared against controls where no fluid was displaced by the concrete. Normal pile surfaces were investigated. Additionally, the situation of ?soil caked? piles was also tested. In the model tests, eight 15 cm deep, W6 x 15 sections were used for two different embedment depths of 1.5d and 2d, d being the depth of the section. In the full-scale tests, 16 specimens 35 cm deep (W14 x 90 sections) were tested with the embedment varied between 0.5d-2d. The results show that significant bond stresses developed even in the worst placement condition. Recommendations made for revising current values in specifications have already been implemented by the Florida Department of Transportation.

Jan 1, 2013

By Baoxiang Zhang, Jing Zhang

"As extruded Mg-9Zn-0.6Zr-2Er magnesium alloys were hot-rolled at 400°C, followed by solution treatment at 400 °c for 1. 5h and artificial aging at 200°C for 10h. Microstructures and tensile mechanical properties of the alloys after hot rolling, solution and aging treatment were examined respectively. Optical micrographs of the as-rolled and as-solution alloys showed fine grain structures, due to the formation of Er-and Zn-bearing compounds at grain boundaries which obviously improved the thermal stability of the alloy. Yield strength as high as about 335 MPa was obtained for the as-rolled alloy, showing that the mechanical properties of the alloy was greatly benefit from the grain refinement and dynamic precipitation of fine MgZn2 during hot rolling. Due to solution heat treatment, vast majority of the Mg-Zn phases dissolved into the matrix, and precipitated out again as fine dispersoid during the subsequent aging, resulting in an enhanced aging-hardening effect.IntroductionWith high specific strength and low density, magnesium alloy has stimulated significant interest for the applications in microelectronics, aerospace and automobile industries. Due to its HCP structure, magnesium alloys exhibit relatively poor strength and ductility. Great efforts have been made to improve the properties of magnesium alloys.Thermo-mechanical processing which combined with subsequent heat treatment can strengthen magnesium alloys due to the strain-hardening mechanism, homogeneous distribution of second particles and grain refinement [1, 2]. However, commercial wrought magnesium alloys have high tendency of grain growth at high temperature due to lack of effective solutions to stabilize the microstructure [3, 4, and 6]. But Magnesium-RE alloys containing high rare earth were reported to have remarkable thermal-stability, Rare earth (RE), such as Y, Nd, Yb, Gd, Ce, were known to form second-phase particles that have higher thermal stability combining with Zn and matrix in Mg[12-17]."

Jan 1, 2012

By E. Buehler, E. Berry

HE magnetic properties of dilute palladium alloys are of fundamental interest.&apos;&apos;&apos; Neutron diffraction studies3 have indicated that a better understanding of the behavior of these alloys could be realized with the availability of high-purity single crystals of palladium. Crucible melts of 99.999 pct pure palladium were found inadequate for such research. In a successful effort to fill this need, floating zone refining of palladium was undertaken. In this note the results of the initial experiments are reported. Zoning was accomplished in an argon atmosphere using 450 kc rf generator for an energy source. Samples 5 to 6 mm in diam were suspended in a gastight quartz envelope which could be moved vertically through the rf coil. A nominal upward traverse rate of 1.5 mm per min was maintained during a pass. Close coupling was found to be essential for stable retention of the liquid in the zone. Single crystals averaging 3.5 cm in length were obtained. Laue photography showed them to be continuous single crystals without gross imperfections. Several criteria were used for evaluation of the purity of the zoned material: magnetic behavior, low-temperature specific heat and residual resistivity ratios. Table I shows the residual resistance ratios obtained for two samples, one subjected to a single pass, the other zoned four times. It is appilrent that palladium can be zone refined with the electrically active impurities being transported toward the tail end. A decrease in susceptibility for zone-melted specimens over any previously measured material from 1.5" to 80&apos;~ has been obserted by H. J. Williams and R. C. Sherwood4 substantiating the residual resistance data. The specific heat measurements are currently being made3 and will be published at some later date. Discussions with J. H. Wernick and S. C. Abrahams are acknowledged. We also wish to thank G. F. Brennert for the residual resistance measure ments.

Jan 1, 1962

By John Hall

THE recently announced run of three years, nine months and eleven days made by a. crucible steel melting furnace of the Columbia Tool Steel Co., which is claimed as a. world&apos;s record, brings forcibly to our attention the great improvements that have been made in the design, construction and operation of the Siemen&apos;s regenerative crucible- melting furnace since its introduction in this country. Credit for this advance should be given to the furnace designer, the manufacturer of refractories, and the operators of the furnaces, whose persistent efforts and intelligent co-operation in attacking the problem have resulted so satisfactorily. There are three factors that determine the life of a crucible furnace, or any other furnace for that matter : Design, nature of refractories and conditions of operation; (including the nature of steel melted) and to some extent these factors are interdependent. Thus, for instance, if a crucible furnace is to lie operated single turn and allowed to cool off considerably at night, in order to save fuel, the use of clay-brick melting holes may be advisable, since silica brick is not well adapted to endure rep eated heating and cooling. But the total life of a clay-brick melting hole is necessarily short. Again, if local conditions such as danger of flood make necessary the building of the furnace largely above ground, so that the radiation of beat is promoted, the cooling down of the furnace over the week ends, when no steel is melted, will be considerable-and the contraction of the furnace that results tends to wrack it to pieces. The character of the metal being melted affects the life of the furnace to a great extent. Low-carbon steels and steels made from iron and charcoal require higher temperatures and much longer melting tune than high-carbon steel or steel made largely from scrap; the life of the furnace will be shorter, and the number of heats melted will be much less, when such materials are melted.

Jan 9, 1913

By K. Blower

"Since there was no representative from Wesfrob Mines Limited, the information on their infra-red concentrate drying operation, which had been prepared by Mr. K. Blower, was presented by Mr, Dorland. Mr. Blower, in submitting the information, emphasized that their objectives in this operation were (a) to guarantee less than 90%, of flow-moisture in their copper concentrates and thus satisfy marine shipping regulation• and (b) to minimize capital costs, The infra-red dryers have satisfied these objectives.To control final moisture in the copper concentrate, current practice is to preheat the filter cake with steam in the disc filter hood and then conveyor-0r7 the concentrate with infra-red calrod heaters. The application of steam aids the system as follows:1) Improves vacuum pump efficiency.2) Lowers viscosity of filtrate (increased temperature},3) Preheats the cake prior to radiant heating. (150°F)The hot cake discharging from the filter ranges from 10.6 to 10.9% moisture. After radiant heating the moisture level is reduced to 8.5% - 9.7% depending on production rate. Further moisture loss occurs during conveying and transferring to the stockpile for a final shipment moisture ranging from 8.1% to 9.5%. Production rate is frail J to 5 dry short tons per hour.1) #23 Conveyor 18"" flat belt covered from filter discharge to transfer point with 7 heaters end-to-end. Drive - Reeves Vari-Speed, 31:4 ratio, type 332-10-18, class ""D"", driving through a 24:1 ratio Dodge reducer. Speed of Conveyor - 3,9 feet per minute to 19.6 feet per minute. (Speed has been established and is not changed as a rule from the present level of a1:out 15.)2) #23 Conveyor 24"" wide, 20° troughed belt covered with 21 heaters, end-to-end from loading point, Speed - Constant at 54,2 feet per minute."

Jan 1, 1972

By Thomas M. Drown

IN the course of some experiments on the analysis of pig iron, I heated, in a platinum crucible, some borings of a graphitic pig iron with sodium carbonate. When the crucible was at a full red heat and the carbonate was thoroughly fused, I noticed a lively ebullition of the mass, and an escape of gas, which burned on the surface. On investigation this gas proved to be carbonic oxide, and on examining the borings in the bottom of the crucible after an hour or two, they were found to be perfectly malleable, although unchanged in general form and appearance. Analysis showed that the carbon was completely removed. I then repeated the experiment, to ascertain whether the silicon and phosphorus were affected, and found that these elements too were largely removed, and could be found in the fused mass as alkaline silicates and phosphates. In order to ascertain whether the removal of the silicon and phosphorus was merely a surface action or whether the reaction really extended into the mass of the iron, I tried the following experiments : A number of bars of pig iron were cast about one foot long and planed down-accurately to one inch section. These were immersed in a large wrought-iron pot full of molten sodium carbonate made by fusing the commercial bicarbonate of soda. Through the kindness of Mr. Frank Firmstone, Superintendent of the Glendon Iron Works, Easton, I was enabled to keep this pot at a reasonably constant high temperature for a long time in one of the hot-blast ovens. One of the bars was removed from the pot every twenty-four or forty-eight hours, according to the rapidity of the action, and after cooling was broken and the fracture examined. The change from pig iron to malleable iron was progressively inwards and always sharp and easily recognized, the rate of progression being in a decreasing ratio with the time. The temperature of the oven had evidently

Jan 1, 1879

Until a comparatively few years ago, interest in tantalum was limited almost wholly to its scientific investigation, but its extreme resistance to the action of even the strong mineral acids, its great avidity for the common gases, hydrogen, oxygen and nitrogen, and its capacity for transforming alternating to direct current are winning for it a place in our industrial life. Tantalum is not attacked by any single acid except hydrpfluoric, nor is it affected by solutions of alkalies. Aqua regia, which readily dissolves both platinum and gold, has no action on it. This resistance to the common corrosive agents is an outstanding property of tantalum and accounts for many of the applications to which it has been put. When heated, tantalum reacts readily with oxygen and nitrogen and absorbs large volumes of hydrogen, 740 volumes being taken up at a dull red heat. This capacity for absorbing gases is being utilized to an increasing extent in the manufacture of vacuum tubes, in which tantalum is used for the metal parts, especially for grid wire. It is said to be a superior metal for this purpose, particularly in power and sending tubes, because of its low secondary emission. The use of tantalum in the manufacture of electrodes, dishes, spatulas and other laboratory apparatus appears to be fairly steady. There has been some development in its use for dental instruments, surgical tools, pen points, hypodermic needles and acid-proof pumps. Recently it has been used in the manufacture of spinnerets for the rayon industry, of nozzles for the manufacture of artificial casings for sausages and of lining for plant equipment. Tantalum in Electrolysis It has been known for some time that certain substances permit the passage of an alternating current in one direction more readily than in the other. Tantalum possesses this property to a marked degree.&apos; When an alternating current is passed through a cell with tantalum electrodes and sulfuric acid electrolyte, a thin film is soon formed at the

Jan 1, 1930

By Christian Ludwig, Virginie Silberstein, Rizlan Bernier-Latmani, Simona Regenspurg

"Residues from waste incineration (bottom ashes) form large amounts of heavy metal-rich waste. Theoretically, heating and the addition of chloride to the ashes could remove these metals by formation of volatile metal chlorides. The remaining heavy metal-poor ashes could be used, for example, as cement additives. In the proposed process of our study we used bypass dust from the cement industry as chloride additives to the bottom ashes. We aim to determine experimentally the optimal conditions to remove heavy metals from ashes and to simulate this process by thermo- chemical modeling. In our experiment we investigate heavy metal flows by heating of differently composed mixtures of bottoms ash and bypass dust in dependence of different furnace temperatures (500-1200 °C). Furthermore, we investigate the reactivity (leaching characteristic) of the resulting product in order to predict if secondary residues can be landfilled in agreement to Swiss regulations for inert materials.IntroductionThe incineration of garbage is generally considered as the most environmentally friendly method for the reduction of municipal solid waste. This is because, compared to traditional storage of waste on landfills, incineration produces less greenhouse gases and destroys toxic organic compounds. The released exothermic energy can be recuperated and the residues from the combustion chamber (bottom ash) are strongly reduced in volume. However, they still form about 600 kt of waste per year in Switzerland, which needs to be landfilled. However, these residues could be potentially used as construction materials after mechanically recovering ferrous and non-ferrous metals. However, the resulting ashes (discharged dry or wet) still contain increased amount of heavy metals (exceeding state regulation) requiring them to be finally deposed on a hazardous waste site. A thermal treatment of these ashes could enable both, to separate and recuperate the remaining heavy metals and an inorganic heavy-metal poor material. The evaporation of metals depends on temperature and can be lowered by addition of chlorides, which would lower the boiling point of most metals by formation of metal chlorides (table 1). 745"

Jan 1, 2008

ZAY JEFFRIES (written discussion*).-I have read with much interest Mr. Ruder&apos;s discussion of Professor Howe&apos;s paper, "The Supposed Reversal of Inheritance of Ferrite Grain Size from that of Austenite." I am yet of the opinion that my first explanation&apos; of Mr. Ruder&apos;s samples is substantially correct. In that explanation I did not intend, however, to convey the impression that "reversed inheritance" was the general rule nor even of common occurrence but rather that." Non-inheritance" was the general rule. Mr. Ruder suggests that a " perfectly formed" grain is an indication of inheritance. The grains in my Fig. 52 are perfectly formed and in fact more nearly equiaxed than those in Mr. Ruder&apos;s Fig: C,3 yet the grains in the former are known not to be inherited but to have been formed by the partitioning of larger austenite grains. On close examination of Mr. Ruder&apos;s Fig. C the very shapes of the grain suggest partitioning. Again, the grain size (25 to 30 grains per square millimeter) is at least 10 or- more likely 20 times smaller than might be expected of the austenite from which these grains were .formed under the given time and temperature conditions. Mr. Ruder&apos;s newer results on electrolytic and Armco iron are most interesting and instructive. His results fit in. nicely with my conclusions 5, 6 and 10.4 His photographs, however, indicate that the thickness of the pieces of sheet metal are such that abnormal grain growth is promoted. He indicates that equilibrium grain size after heating to 950° C., with furnace cooling, is about the same as his Fig. 1, above. I estimate this to be approximately one-half -grain per square millimeter, or 40 times as large as I have obtained with the same material (Armco iron) after heating Y4-in. bars to 1300° C. for 2 hr. and cooling in the furnace. The effect of thickness of sample on grain size is one which needs more attention.

Jan 3, 1918