Search Documents

By Lon Santis, Scott Deitchman, John A. Decker

This report describes three cases of carbon monoxide (CO) poisoning in a manhole, including one fatality, from CO migrating through soil after nearby use of explosives. A municipal sewer project involved installation of new pipes and manholes. Work of the general construction contractor was interrupted when a subcontractor detonated 265 pounds of nitroglycerin-based explosive 40-60 feet south of the manhole to break up underlying rock. A construction worker who descended into the manhole 45 minutes after the explosion collapsed within minutes, and two co-workers descended into the manhole to rescue him. One rescuer retrieved the unconscious worker, and the other rescuer died in the manhole. All workers had elevated carboxyhemoglobin levels. In the subsequent NIOSH investigation, air monitoring was conducted with real-time instruments, and air samples were collected in Tedlar bags. Laboratory analyses of the bag samples collected near the bottom showed 1905 parts per million (ppm) CO, 19.5% oxygen, and 3% carbon dioxide. Direct reading instruments showed progressively higher concentrations as the sensor was lowered into the manhole. Subsequent chamber tests on sample explosive yielded 27 liters CO per kilogram detonated. Based on this value, the surface blast at the construction site may have produced about 3,250 liters (114.8 cubic feet) CO. The CO in this incident most likely was released from the nearby explosion and migrated through soil and fractured rock into the manhole. The blasting and construction industries should be made aware of this previously unrecognized CO exposure hazard associated with surface blasting. The extent of CO exposure from explosives used in construction is not known, and additional information on the extent of CO exposure must be collected. In addition, confined space entry procedures (including monitoring confined space atmospheres before entry) should be observed; CO monitoring of confined spaces in the presence of blasting can prevent future incidents such as this one.

Oct 30, 1997

By Frederick Burbridge

The Morning silver-lead-zinc mine of the Federal Mining & Smelting Co. is about 'two miles northwest of Mullan, Ida. The lode is a metasomatic fissure vein. The orebody is approximately 2000 ft. long within the bounds of the property and varies in width from knife edge stringers to 50 ft. It has been developed to a depth of 3600 ft. and stands nearly vertical in Revett quartzite, which .strikes north 65" west. The high-grade veins and lenses are generally mixed with waste (siderite, quartz, and quartzite). The average grade of ore to sorting plant in 1921 was 4 oz. silver per ton, 8.6 per cent. lead, and 4.1 per cent. zinc. Wall rock stands only a short time without timbering. The minimum angle of gravity flow is 45". The ratio of waste sorted out to ore is 6 per cent. No gases are generated underground and temperature has no influence on mining operations. Fresh air is forced down the air raise and up the main shaft. Drifting and Stoping Main drifts 12 ft. wide and 13 ft. high are driven every 200 ft. (vertically) and are connected by raises 125 ft. apart. These raises consist of three compartments (chute, tramway, and timber slide) and are for the purpose of ventilation, access, and hoisting supplies to stopes. Ground is stoped between raises. Chutes are placed every 25 ft. for drawing off ore broken in stopes. Waste for filling is obtained from waste raises off the stope in walls or waste is dumped from the level above down the chute compartment of raises, which is bulkheaded so that waste can be drawn off at any floor as required. Timbering Posts and caps for square sets (varying in diameter from 6 to 24 in.) are cut to length in a sawmill on the surface. No preseratives are used. Timber is taken on a flat car along drifts to a raise nearest the working place and hoisted as required. Practically no timber is salvaged for

Jan 1, 1925

By W. T. Jr. Thom

IN PREVIOUS classifications of coal, it has been customary to regard moisture eliminated from coal samples between 20° and 100° C. as extraneous matter, rather than as a constituent part of the coal. It seems, however, that the physical character and use properties of the low-rank coals are directly related to the amount of such moisture present, and recent chemical work has shown1 that such coals contain unstable groupings which decompose between 20° C. and temperatures somewhat above 100° C., with the splitting off of moisture. According to this view, the moisture eliminated from air-dried coal below boiling point is similar in all essential respects to moisture eliminated above 100° C., and is produced by analogous reactions; and inasmuch as the moisture given off above 100° C. has always been treated as a constituent of the volatile matter of coal, it would seem that consistent usage would include as a part of the volatile matter all moisture present as an essential component of the coal as it occurs in nature. As a matter of experience, it seems clear that the general physical and chemical characteristics of the low-rank coals are largely determined by or related to the moisture, whether chemically or physically combined, present in air-dried coal; it is also demonstrable by trial that the low-rank coals cannot be satisfactorily classified on a purely chemical basis by using the moisture free form of analysis. The low-rank coals of the western United States include numerous well-defined types, many of which were referred to in a classification proposed by Ashley,2 in which the physical and use properties of the coals were made the primary basis for their systematic grouping. When testing this classification by replotting analyses of these type coals according to the Seyler scheme of classification,3 a satisfactory parallelism between use properties and chemical constitution of the dry coal was found among

Jan 5, 1925

By M. R. Khalesi, S. Arfania

"Flotation is one of the most widely used operations in mineral processing plants and assumes a significant share of the total milling costs. The purpose of this paper is to introduce a new set of capital and operating cost models for major flotation machines based on the application of single (SRA) and multiple regression analysis (MRA). Thirty-seven major flotation machines were analysed for this purpose. Depending on the machinery type, different technical variables such as diameter, required air flow rate, required floor space, cell volume, required air pressure, and power were considered as predictor variables, individually (in SRA) or simultaneously (in MRA). Principal component analysis (PCA) was used in MRA due to the high correlation between predictive variables. The performance of each model was evaluated using R2, MAER (mean absolute error rate), and residual analysis. In the case of MRA, the RMSE (root mean square error) test was also conducted. Maximum obtained MAER of 13.5% and minimum R2 of 0.86 indicated that these models could be applied as credible tools in estimation of capital and operating costs of flotation machines for design and feasibility studies.IntroductionMineral processing is a vital part of mining projects and mainly involves comminution, sizing, concentration, extractive metallurgical processes, and dewatering. Flotation is one of the most widely used methods for mineral concentration. Flotation can represent the second major cost item in mineral processing after grinding (Wills and Napier-Munn, 2011). Accordingly, it is a main concern of mining project managers to select and optimize flotation circuits in order to decrease costs and increase productivity. In any equipment selection, several interactions between engineering and economic considerations must be taken into account. Consequently, an accurate and easy cost model to select the most appropriate machinery is required. Moreover, cost models could be used in flow sheet simulations applied in design and optimization. Models of unit operations built into the simulators could be improved by linking the equipment cost models (Khalesi et al., 2015)."

Jan 1, 2017

By J. D. Kalasky

Continuous mining has revolutionized the coal industry but intensified the problems of earlier mechanization. From the installation of the first miner, it was recognized that face ventilation would be one of these problems. To establish an efficient work cycle for the equipment being used, conventional mechanized mining provides four or more development faces. Continuous mining, relying on a single machine, requires only one face, although more than one can be driven alternately by the same machine. In gaseous areas mined by the older methods, the intermittent rate of exposure allows time for the face to bleed off or be cleared, and the width obtained with conventional units makes it possible to hang a brattice line almost to the face. Continuous mining increases the ventilation hazards; there is no margin of time, and very limited space. For all practical purposes, continuous miners available today can be grouped into two major types, rippers and borers. The two can be further classified, respectively, as flexible and rigid. Both types have been in operation in U. S. coal mines for the past five to ten years in a number of seams, under various conditions ranging from slightly gaseous to very gaseous. Common methods of face ventilation utilizing jute or plastic brattice material for line curtains, stoppings, and checks have so far met with success. Air volumes to operating sections are greater than for conventional mining, and specific instructions have been given to section crews stressing the precautions needed in dealing with a steady rate of gas emission and the importance of maintaining reasonably air-tight brattice to direct a good steady flow toward the face at all times. Operators of continuous miners, as well as the foreman on each section, are equipped with an approved safety lamp for gas testing. When the miner is in steady operation, tests for gas at the face are made at 15 to 30-min intervals, depending on the

Jan 1, 1960

By W. T. Thom

In previous classifications of coal, it has been customary to regard moisture eliminated from coal samples between 20 and 100 C. as extraneous matter, rather than as a constituent part of the coal. It seems, however, that the physical character and use properties of the low-rank coals are directly related to the amount of such moisture present, and recent chemical work has shown' that such coals contain unstable groupings which decompose between 20 C. and temperatures somewhat above 100" C., with the splitting off of moisture. According to this view, the moisture eliminated from air-dried coal below boiling point is similar in all essential respects to moisture eliminated above 100" C., and is produced by analogous reactions; and inasmuch as the moisture given off above 100" C. has always been treated as a constituent of the volatile matter of coal, it would seem that consistent usage would include as a part of the volatile matter all moisture present as an essential component of the coal as it occurs in nature. As a matter of experience, it seems clear that the general physical and chemical characteristics of the low-rank coals are largely determined by or related to the moisture, whether chemically or physically combined, present in air-dried coal; it is also demonstrable by trial that the low-rank coals cannot be satisfactorily classified on a purely chemical basis by using the moisture free form of analysis. The low-rank coals of the western United States include numerous well-defined types, many of which were referred to in a classification proposed by Ashley,2 in which the physical and use properties of the coals were made the primary basis for their systematic grouping. When testing this classification by replotting analyses of these type coals according to the Seyler scheme of classification,3 a satisfactory parallelism between use properties and chemical constitution of the dry coal was found among

Jan 1, 1925

By H. B. Menardi

The history, geology, ore deposits and current mining operations of the Huitzuco district have been described by C. W. Vaupelll and the current mill operations by David Segura.2 This paper completes the story of Huitzuco with a description of the reduction of the flotation concentrates. The predominant ore mineral in the Huitzuco deposit is livingstonite, a rare, mercury-antimony sulphide (HgS.2Sb2S3). Other associated minerals include cinnabar, stibnite and elemental sulphur. The gangue is largely limestone and gypsum. Former operators mined a selected grade of ore, from which the mercury was recovered by an expensive, inefficient operation. A considerable tonnage of rejects and fills, carrying mercury and antimony, was left in the mine. In order to recover both mercury and antimony from these fills and also from newly developed ore, a combination method has been developed, by means of which the livingstonite is concentrated by flotation and the flotation concentrates subsequently reduced to metallic mercury and antimony. An essential part of the flotation treatment, as developed by Segura, is the use of copper sulphate as an activating agent. A typical analysis of concentrates now being produced at the property is as follows: Hg, 7.73 per cent; Sb, 26.40; Fe, 1.20; S, 29.68; CaO, 11.50; MgO, 7.25; SiOz, 1.63; A1203, 0.65. PRocess foR Treatment op Concentrates In the development of a process for treatment of these concentrates, three different methods were investigated: (1) roasting in a Dwight-Lloyd sintering machine with an excess of air; (2) separation of mercury and antimony by distillation in a reducing atmosphere; (3) a third method, which ultimately developed into the present process. The third method involved a slow calcination at a closely regulated temperature with a limited admission of air, which separated the mercury and antimony, the raeroury passing out of the kiln with the furnace gases and the antimony remaining in the calcine or "sinter."

Jan 1, 1944

By Linda L. Chasko, Larry D. Stowinsky, Ronald S. Conti

Mine operators often rely on mine rescue teams to save lives during an underground emergency such as an underground fire, explosion or roof fall. It is extremely important that team members are provided with adequate exploration equipment and that training simulations are conducted in a realistic manner. A series of mine rescue training exercises was developed, conducted and evaluated by the National Institute for Occupational Safety and Health (NIOSH) in cooperation with the Pennsylvania Department of Environmental Protection, Bureau of Deep Mine Safety. The exercises were conducted at NIOSH’s Lake Lynn Laboratory during 1995 to 1998 and resulted in improved technology and training for mine rescue teams. For example, existing technologies were identified to help rescue teams during exploration. These included chemical light sticks to identify team members and mark crosscuts and mine materials, strobe lights for mapping out escape ways, and a helmet mounted thermal imaging system to see through smoke. A hands-free communication system showed potential for enhanced communications between team members and the fresh air base. A new high-visibility team lifeline that allows for flexibility of movement between team members was developed. A positive-pressure inflatable escape device (IED) was used to isolate the “hazardous” environment from fresh air and allow rescue team members to traverse through. An inflatable feed-tube partition that can rapidly block large openings such as underground passageways and simultaneously provide a feed-tube for high-expansion foam generators was also deployed for several simulations. During the simulations, mine rescue team members donned self-contained breathing apparatuses (SCBA) and traversed more than 305-m of mine passageways filled with nontoxic smoke. Visibility ranged from 0.3 to 0.9-m. In one area of the mine, a kerosene heater was used to simulate a fire and reduce the oxygen concentration. In another area, a 1.5 pct methane zone was established. The team members searched for "victims,” mapped the passageways, built temporary stoppings and ventilated the smoke-filled entries. The teams indicated that the simulations were challenging and very informative.

By Lewis H. Reiland

IN 1920, for the first time, the U. S. Geological Survey employed aerial photography in constructing planimetric maps. Contours were added by aerial photography and cultural details corrected. From 1925 to 1929 photogrammetric plotting machines and instruments of foreign design appeared in America for use in constructing complete topographic maps. During this period the only American technique developed was the Brock process, carried out with great success by Aero Service Corp. of Philadelphia, a pioneer in the field of photogrammetry. Between the first and second world wars the Multiplex projector, the Aerocartigraph, and the Stereoplanigraph appeared. The Multiplex projector, most popular of the three, determines three-dimensional values with very high accuracy. Many refinements have been added year by year, and it is now possible to photograph vast areas in a very short time and produce planimetric, topographic, and geologic maps of great value at very low cost per acre as compared with all methods previously known and in use. Both on the ground and in the air, however, accurate results can be produced only with highly skilled personnel and costly scientific instruments and machines. As early as 1928 the writer collected from the U. S. Army Engineers all available formulas and data on photogrammetry and personally contracted a local project of 2800 acres to be surveyed from the air. From the 10,000-ft altitude required for scale the cameras, each equipped with 4-K filters, pierced a ground haze of about 5000 ft, achieving clear, de- finable photography. The result was so gratifying, and the continuing progress in this method of surveying and mapping so great, that in the matter of economy it can hardly be surpassed. Pocahontas Land Corp., for example, constantly refers to its complete file of aero prints, covering its entire ownership in West Virginia, Virginia, and Kentucky. Photostats are enlarged or reduced from these prints to match the scale of company maps, to which various features are then added.

Jan 7, 1957

By G. St. J. Perrott

ONE of the important hazards in coal mining is the danger of ignition of explosive mixtures of methane and air or coal dust and air, or both, by the explosives used in blasting the coal. It has long been recognized that certain explosives are more dangerous than others in this respect. In America and abroad, government testing stations have been established for officially passing on the suitability of explosives for use in coal mines. In this country the Federal government is given no power to enforce the use of the approved explosives but merely publishes from time to time, through the Bureau of Mines, those explosives which have passed the tests necessary to place them on the list for use in coal mines. In spite of this lack of police power, the increase in the use of permissible explosives since the promulgation of the first list in 1909 has been rapid. In 1912, only 8 per cent. of the explosives used in coal mines were permissible; in 1925, this figure had increased to 25 per cent. While the past record of permissible explosives has been most gratifying, it is very desirable that we pave the way for further improvement in explosives and blasting methods by learning more about the mechanism of ignition of gas and coal dust by explosives. To this end a considerable amount of investigative work already has been carried out and a large amount yet remains to be done. It is the purpose of this paper to discuss briefly the effect of the characteristics of explosives and method of loading in the borehole on the liability of a blown-out shot to ignite explosive mixtures of gas or dust. For an account of the methods by which an explosive is tested for permissibility for use in coal mines, the reader is referred to Schedule 17-A of the U. S. Bureau of Mines.

Jan 10, 1926

By J. E. Tiffany

"The new permissible blasting device, Cardox, utilizes as a blasting agent liquid carbon dioxide which is discharged.as a gas from a steel container or shell. The loaded shell is placed in a borehole, stemmed, and tamped in a manner similar to that employed with explosives, and is fired by electricity.The Bureau of Mines' approval for use of the device in coal mines was granted as Approval No. 1 under date of October 3, 1928; as the result of tests made under the conditions and requirements of Schedule 20. There have been three subsequent extensions whereby minor modifications in the original design were granted.The permissibility of the device is subject to the following conditions; (1) It shall be in all respects similar to the sample submitted for tests; (2) certain thicknesses of disc and. weights of heater ingredient and of carbon dioxide, all of which are set forth in Table 2 under the provisions governing permissibility, must be used: (3) the rear cap must always be in place after the shell has been charged, to prevent accidental firing; and (4) firing must be done by means of a permissible-type blasting unit.The permissibility of Cardox was established by gallery tests similar to those used in testing explosives for permissibility. In these tests the shell was discharged into gallery 1 without causing any ignition of gas and air or of gas, dust, and air mixtures there. The conditions of charging the shell, such as weight of the ingredients of the heater element, the carbon dioxide charge, and thicknesses of the disc, were varied according to the conditions under which it would be likely to be used in blasting. The tests made in gallery 1 are here described in detail, as are also the tests which have been made for determining the propulsive strength of the device and the quantities of poisonous gases given off when a shell is discharged."

Mar 1, 1929

By Charles Becker

THE practice of drying phosphate in Florida is as old as the industry, which began a little more than half a century ago. The methods, however, have changed considerably. At first, the natural process of exposure to the sun and air was used, later supplemented by wood fires beneath open-air stationary dry kilns and drying towers of various designs. It was not until the early nineties that rotary driers came into use, and at first they were of very small design and fired with wood. As the industry grew and tonnage increased, so likewise grew the number and size of rotary driers, until today the largest installations are 6 ft. up to 7 ft. 6 in. in diameter, and 55 to 60 ft. long, fired with crude oil. The reasons for drying phosphate rock are: (1) to eliminate freight on water in the shipment and (2) to facilitate the good grinding qualities required by the buyers in their acidulation. Phosphate pebbles vary materially in natural characteristics and each property has a direct bearing on the processing. In making comparisons of cost and operating conditions, the following are usually taken into consideration: 1. The hard dense pebbles, which contain very little interior moisture and 6 to 8 per cent total moisture, usually produced from the low-grade deposits. 2. The lighter, porous pebbles, which contain 4 to 5 per cent interior moisture and a total moisture ranging from 9 to 15 per cent. 3. The product of recovery operations using oily reagents, containing from 15 to 25 per cent moisture. 4. The size of the pebbles. Usually the plus 5-mesh material is considered as "coarse rock"; the minus 5-mesh plus 24-mesh is "fine rock," and the minute particles below 24 mesh are called "concentrate." 5. The amount of moisture allowed in the dried product. The practice is generally to dry down to 1.5 to 2 per cent moisture. There is, however, an actual range in guarantee of from 1 per cent maximum to 3 per cent maximum.

Jan 1, 1936

By David B. Rushmore

Torches were used by the early Romans for mine-lighting, and these were followed by open lamps or earthen jars filled with tallow or oil, and later by candles. In early coal-mining, explosive gases seldom occurred, and, if they were encountered, the danger of explosion was materially diminished by the absence of any ventilating-system and the consequent insufficient circulation of air to form with the methane an explosive mixture. As the art advanced, the danger of fire-damp became more apparent, and methods for testing the air were resorted to as early as in the fifteenth century. The method of testing consisted in lowering a dog in a basket down the shaft. As soon as he encountered fire-damp he would commence to howl, after which he was withdrawn, and a leafy bush was fastened to the end of the rope and run rapidly up and down the shaft. This so disturbed the accumulation of gas as to cause it to rise out of the shaft. Later this odd method of testing was improved upon through the discovery that a light inserted in a body of fire-damp Gould produce a blue flame. Candles were used for this purpose, and, when fire-damp was thus discovered, brushing or some other primitive method of fanning was resorted to for driving out the gas. In some instances the gas was burned away, regardless of the danger thereby incurred. A man, wearing a well-moistened coat and a mask with glass spectacles, descended in the mine a few hours before each shift. With a long stick, to which was fastened a burning torch or candle, he would crawl on the floor with the stick so raised that the light would sweep the roof and ignite the gas which it encountered. In this position the flame of the explosion would pass over him, after which he would retreat from the gases resulting from the combustion. The occurrence of serious accidents resulted in

Jan 1, 1913

By Charles Becker

THE practice of drying phosphate in Florida is as old as the industry, which began a little more than half a century ago. The methods, however, have changed considerably. At first, the natural process of exposure to the sun and air was used, later supplemented by wood fires beneath open-air stationary dry kilns and drying towers of various designs. It was not until the early nineties that rotary driers came into use, and at first they were of very small design and fired with wood. As the industry grew and tonnage increased, so likewise grew the number and size of rotary driers, until today the largest installations are 6 ft. up to 7 ft. 6 in. in diameter, and 55 to 60 ft. long, fired with crude oil. The reasons for drying phosphate rock are: (1) to eliminate freight on water in the shipment and (2) to facilitate the good grinding qualities required by the buyers in their acidulation. Phosphate pebbles vary materially in natural characteristics and each property has a direct bearing on the processing. In making comparisons of cost and operating conditions, the following are usually taken into consideration: 1. The hard dense pebbles, which contain very little interior moisture and 6 to 8 per cent total moisture, usually produced from the low-grade deposits. 2. The lighter, porous pebbles, which contain 4 to 5 per cent interior moisture and a total moisture ranging from 9 to 15 per cent. 3. The product of recovery operations using oily reagents, containing from 15 to 25 per cent moisture. 4. The size of the pebbles. Usually the plus 5-mesh material is considered as "coarse rock"; the minus 5-mesh plus 24-mesh is "fine rock," and the minute particles below 24 mesh are called "concentrate." 5. The amount of moisture allowed in the dried product. The practice is generally to dry down to 1.5 to 2 per cent moisture. There is, however, an actual range in guarantee of from 1 per cent maximum to 3 per cent maximum.

Jan 1, 1936

By Charles N. Becker

The practice of drying phosphate in Florida is as old as the industry, which began a little more than half a century ago. The methods, however, have changed considerably. At first, the natural process of exposure to the sun and air was used, later supplemented by wood fires beneath open-air stationary dry kilns and drying towers of various designs. It was not until the early nineties that rotary driers came into use, and at first they were of very small design and fired with wood. As the industry grew and tonnage increased, so likewise grew the number and size of rotary driers, until today the largest installations are 6 ft. up to 7 ft. 6 in. in diameter, and 55 to 60 ft. long, fired with crude oil. The reasons for drying phosphate rock are: (1) to eliminate freight on water in the shipment and (2) to facilitate the good grinding qualities required by the buyers in their acidulation. Phosphate pebbles vary materially in natural characteristics and each property has a direct bearing on the processing. In making comparisons of cost and operating conditions, the following are usually taken into consideration: 1. The hard dense pebbles, which contain very little interior moisture and 6 to 8 per cent total moisture, usually produced from the low-grade deposits. 2. The lighter, porous pebbles, which contain 4 to 5 per cent interior moisture and a total moisture ranging from 9 to 15 per cent. 3. The product of recovery operations using oily reagents, containing from 15 to 25 per cent moisture. 4. The size of the pebbles Usually the plus 5-mesh material is considered as "coarse rock"; the minus 5-mesh plus 24-mesh is "fine rock," and the minute particles below 24 mesh are called "concentrate." 5. The amount of moisture allowed in the dried product. The practice is generally to dry down to 1.5 to 2 per cent moisture. There is, however, an actual range in guarantee of from 1 per cent maximum to 3 per cent maximum.

Jan 1, 1938

By Charles N. Becker

The practice of drying phosphate in Florida is as old as the industry, which began a little more than half a century ago. The methods, however, have changed considerably. At first, the natural process of exposure to the sun and air was used, later supplemented by wood fires beneath open-air stationary dry kilns and drying towers of various designs. It was not until the early nineties that rotary driers came into use, and at first they were of very small design and fired with wood. As the industry grew and tonnage increased, so likewise grew the number and size of rotary driers, until today the largest installations are 6 ft. up to 7 ft. 6 in. in diameter, and 55 to 60 ft. long, fired with crude oil. The reasons for drying phosphate rock are: (1) to eliminate freight on water in the shipment and (2) to facilitate the good grinding qualities required by the buyers in their acidulation. Phosphate pebbles vary materially in natural characteristics and each property has a direct bearing on the processing. In making comparisons of cost and operating conditions, the following are usually taken into consideration: 1. The hard dense pebbles, which contain very little interior moisture and 6 to 8 per cent total moisture, usually produced from the low-grade deposits. 2. The lighter, porous pebbles, which contain 4 to 5 per cent interior moisture and a total moisture ranging from 9 to 15 per cent. 3. The product of recovery operations using oily reagents, containing from 15 to 25 per cent moisture. 4. The size of the pebbles Usually the plus 5-mesh material is considered as "coarse rock"; the minus 5-mesh plus 24-mesh is "fine rock," and the minute particles below 24 mesh are called "concentrate." 5. The amount of moisture allowed in the dried product. The practice is generally to dry down to 1.5 to 2 per cent moisture. There is, however, an actual range in guarantee of from 1 per cent maximum to 3 per cent maximum.

Jan 1, 1938

By G. E. Erdman

Gouverneur Talc produces a dry mineral filler from the tremolite talc rocks located near Gouverneur, New York. The raw material for this rock powder is a silicate rock and dust is controlled by water sprays whenever it becomes a problem underground. In the milling operation, there are some nine baghouse-type dust collectors which are utilized for the control of dust created in the crushing and grinding process. These collectors have been installed over a period of years since 1947 and are assigned to specific areas where the particle sizing of the dust can be returned to the plant circuit or product involved at the point of collection. It has been found very advantageous to mount most of these collectors on the top of the mill building and packhouses where the return of the dust can be accomplished by a gravity feed. In the years of effort involved in efficient control of dust generated in the plant, many things have been learned in the construction of ducts for control valves. The company has found useful such things as grasshopper legs for interconnecting silos with similar products, the elimination of fiat dust ducts, cleaning cyclones for coarse dust or heavy loadings, refractory linings for cyclones and certain duct areas, and the avoidance of square intersections when diverting or combining ducts. Operating cost records indicate that collectors handling the finest dust have the least expense. Operating costs on high-temperature dusts generally run higher than other types of material collected. Experience further indicates that the multiple cyclone-type collectors can provide a low cost and efficient way of removing hot dusts from process air streams before the introduction of the material into a baghouse. High moisture conditions and cold northern climates have been found to combine and create conditions under which baghouses can not efficiently function as dust collectors. Gouverneur Talc feels that its several dust collection systems have been a considerable maintenance expense but well worth the cost when it came to safeguarding the employees' health and preventing air pollution.

Jan 1, 1974

By Raymond D. Daniels, Frank E. Rizzo, James D. Gerber

ThIS discussion describes a method for the addition of small amounts of oxygen to columbium (niobium) in an accurate and reproducible manner. The method is based on the complete reduction by columbium of a carefully weighed amount of another metal oxide. The equilibrium Pq associated with Cb-CbO mixtures is extremely low, e.g., 10"25 atm at 100O°C, and the pressures over Cb-0 solutions are even lower. The equilibrium Pq associated with a given metal-metal oxide mixture can be easily obtained, with the aid of a Richardson-Jeffes chart.' Although columbium should effectively reduce almost any metal-metal oxide combination, the proper choice of a metal-metal oxide system is complicated by the low rate of oxygen transport in the gas phase at low oxygen pressures and the difficulty in reducing any columbium suboxide formed during the reduction of the oxygen source material. Thermodynamically, oxide formation on columbium will be avoided so long as the oxygen partial pressure over the columbium is below the equilibrium pressure associated with the mixture Cb-CbO. The logical choice of a source for oxygen would appear to be a mixture of Cb-CbO, since oxide formation would be precluded by nucleation difficulty. But calculations using the kinetic theory of gasses indicate that, for a temperature of 900°C, the reaction would proceed too JAMES D. GERBER, formerly Research Assistant, University of Oklahoma, Norman, Okla., is Research Metallurgist, Air Force Weapons Test Laboratory, Kirtland Air Force Base, N. Mex. FRANK E. RIZZO, Junior Member AIME, formerly Assistant Professor of Metallurgy, University of Oklahoma, is Associate Professor of Metallurgy, University of Texas at El Paso, El Paso, Tex. RAYMOND D. DANIELS, Member AIME, Professor of Metallurgical Engineering, University of Oklahoma, is an NSF Fellow, Institute de MBtallurgie Structurale, Universite de euch:tel, Neuchitel, Switzerland. Manuscript submitted October 28, 1968. IMD

Jan 1, 1970

By C. A. Heiland

The new geophone described herein was developed by Charles H. Hull, instrumentmaker of the Colorado School of Mines, and the writer. The first geophone was invented during the war for the purpose of detecting enemy sapping or underground mining operations and for locating enemy artillery. It is based on the principle of the seismograph—a heavy lead mass suspended by one or two diaphragms, which are clamped to an air-tight case. When the ground vibrates during the transmission of sound waves, the case moves with it while the so-called steady mass remains practically motionless. Attached to the top of the casing is a hose leading to an earpiece shaped like a stethoscope. When the mass and the diaphragm move up and down in the case, the air is compressed and rarified in the inside; thus the vibration is communicated as sound wave to the human ear. The geophone combines a surprising simplicity of construction with an extreme sensitivity. Other listening instruments were developed during the war, adaptations of the telephone and the microphone—that is, instruments operating through the medium of electricity—of which the so-called seismicrophone, an adaptation of the carbon-granule microphone receiver, probably has found the greatest application, but such instruments apparently have not proved as useful as the simple geophone despite obvious advantages arising from the use of electricity. The carbon receivers were more subject to extraneous noises and to what is called "frying," and they did not offer the advantage possessed by the geophone; namely, the simultaneous use of two receivers, which makes it possible to determine the location of the source of sound. During the war, the U. S. Bureau of Mines made a study of the geophone and of the propagation of sound waves through rock. These studies have been continued, as the earlier results proved the possibility of using the geophone in various non-military ways, principally in mining, and the results of these studies have been published.'

Jan 1, 1932

By C. E. Beecher

The application of gas or air under pressure to obtain more oil from a sand which has been practically exhausted by ordinary production methods has been practiced to a limited extent for many years. Until recently such methods were confined to the Eastern fields, principally those of Ohio and West Virginia, where in many cases the production obtained after applying pressure for a few years was nearly equal to the total production prior to that time which had been obtained by the usual production methods. As early as 1917, J. 0. LewisL called attention to this method of increasing the recovery of oil and cited the phenomenal results obtained by H. E. Smith, I. L. Dunn and 0. C. Dunn, who pioneered the application of air or gas pressure recovery methods. With this information available it would appear that other oil-producing sections of the country have been extremely slow to realize the advantages of repressuring. However, after a few successful projects in the Mid-Continent area, the oil producers appreciated t' e value of this method for obtaining further and profitable production from their practically exhausted leases and are now making extensive use of it. In general, it has been the practice to apply pressure to the sands when production has declined to a small yield per well. The purpose of this paper is to discuss some of the advantages which may be expected from returning gas under pressure to the oil sands during the early stages of development, before the rock pressure has been dissipated and the gas exhausted, and to stimulate discussion of this subject on which comparatively little actual field data are available. The Function of Gas Gas associated with or dissolved in the oil is the source of energy causing movement of the oil to the well. When this energy is dissipated production ceases. The exception to this general statement is found in fields where hydrostatic water pressure may supply energy after the gas

Jan 1, 1929