Search Documents

By Robert L. Bates

On April 2 and 3, 1970, more than 100 geologists attended the Sixth Annual Forum on Geology of Industrial Minerals at Ann Arbor, Mich. After this brief appearance, the Forum apparently ceased to exist- but it didn't really, and another spring will see it again in action, in another corner of the country. The organization might be characterized as the country's largest permanent floating conference on the geology of industrial minerals. What is the Forum, where did it come from, and what is it up to? The idea originated in 1964 with a small group in the Department of Geology at Ohio State University, Columbus. This group felt that a forum was needed for the exchange of geologic information on industrial rocks and minerals. They envisioned an approach-which has subsequently been adhered to--that would be dominated neither by geological academics interested in theoretical problems nor by practical engineers concerned with processing large tonnages of rock. It was proposed to focus attention on the middle part of the spectrum, especially on practical problems of geological occurrence and how these problems affect extraction and use. In terms of the standard rock-products flow sheet, which starts with a truck unloading into the primary crusher beneath the words 'from quarry,' it was proposed to focus geological attention on what is beyond the primary crusher, out in the quarry.

Jan 1, 1970

By R. K. Datta, T. S. Davis

YVO4:EU, excited under 3650A radiation, shows a marked increase in total brightness with in~rease in temperature. At 25°C the response to 3650A radiation is about 48 pct of its maximum response which occurs at about 350°C, Fig. 1. In an attempt to explain the phenomenon, one of the present authors' (R.K.D.) investigated the diffuse reflectance spectra of the phosphor at different temperatures (up to -150°C) and was unable to observe any significant change to which the increased brightness could be reasonably ascribed. Since then diffuse reflectance spectra at elevated temperatures have been obtained in this laboratory using an improved device. A significant decrease in the diffuse reflectance of a phosphor in the ultraviolet region—especially in the longer wavelength region—at -300°C has been observed. The purpose of this note is to describe the device used for high-temperature reflectance measurements and to explain the increased brightness of YVO4:Eu phosphor at elevated temperatures under 3650A excitation. Experimental. YVO4 and YVO4:Eu samples were prepared as previously described.' The elevated-temperature reflectance spectra were obtained with a Cary 14 spectrophotometer equipped with a diffuse reflectance accessory and a ring collector. CaF2 was used as the standard. The cell used

Jan 1, 1969

By A. W. Hahn

THE importance, to geologists and metallurgists, of knowing the mineralogical forms in which the silver occurs in ores has increased during the past few years, and will continue to increase as long as working hypotheses are converted into proved theories and rule of thumb methods are supplanted by scientific data. The methods used for the determination of these silver minerals have been: (1) careful study of polished ore sections with the microscope, and more recently, (2) metallurgical separation of the ground ore by flotation, tabling and panning, supplemented by microscopic examination of these separated minerals, and chemical analyses. During the course of some experimental work carried on by the testing department of the International Smelting Co. and myself, it becomes important to determine, in a general way, the distribution of the silver values in the minerals, as they exist in Tintic Standard and North Lilly siliceous oxidized lead-silver ores. These mines are in the East Tintic Mining District, State of Utah. In this work the second method was used. Differential flotation tests were run, separating the sulfide from the oxidized minerals, and the products were assayed. Various concentrates were carefully panned and the separated products assayed; special samples of ore were selected and assayed. The microscope was used only for the purpose of determining whether the individual minerals were in the so-called "free" state.

Jan 1, 1929

By William H. Hartwig

A paper by Rose1 has called attention to some of the problems of wetting-liquid relative permeability measurement. The premises and conclusions set forth by Rose, namely the applicability of the Hassler scheme of measurement, will be accepted. In addition, it will be concluded that certain electrical analog circuits can be used as a pattern for consideration of possible hydraulic systems of measurements. NEW SCHEME OF MEASUREMENT The object of this note is to propose a new scheme of wetting liquid relative permeability measurement. It is significantly different from those heretofore described, nonetheless it is based on Hassler concepts. The scheme is illustrated in Fig. 1 in terms of the corresponding electric circuit analog. It may be designated descriptively as the "comparison" method of wetting-liquid relative permeability measurement. In this circuit, R, represents the resistance of the core sample which is being studied for relative permeability characteristics, R represents a "standard" resistance, R represents the combined series resistance of the barrier pads, R R2 represent the combined series resistance of barrier pads in the manometer circuit, C, C represent the capacitance of the manometers, E is a constant voltage source, S is the switch or stopcock. The following conditions are imposed upon .the network: Rb » R, and R, R,» R, R, » R., and the condensers C, and C,

Jan 1, 1953

George B. CoRless, Chairman. Superintendent, Gulf Coast Division, Humble Oil & Refining Co., Houston, Texas. W. H. Geis, Associate Chairman. Geologist, Los Angeles, California. Benjamin C. Craft, Secretary-Treasurer. Associate Professor, Petroleum Enginecring, Louisiana State University, Baton Rouge, La. Executire Committee George B. Corless, Chairman. M. Albertson, Production Engineer, Shell Petroleum Corporation, Houston, Texas. D. R. Knowlton, General Production Superintendent, Phillips Petroleum Co., Bartlesville, Oklahoma. R. P. McLaughlin, General Manager, Dominguez Oil Fields Co., Los Angeles, California. Hallan N. Marsh, Production Engineer, General Petroleum Corporation of California, Los Angeles, California. Theron Wasson, Chief Geologist, The Pure Oil Co., Chicago, Illinois. Production Engineering M. L. Haider, Vice-chairman. Petroleum Engineer, Carter Oil Co., Tulsa, Oklahoma. Joseph Chalmers, DeBataafsche Pet. Maatschappij, The Hague, Netherlands. Emile HugUenin, Deputy State Oil and Gas Supervisor, Los Angeles, California. Carl E. Reistle, Jr., Petroleum Engineering Department, Humble Oil & Refining Co., Houston, Texas. Production J. TERry Duce, Vice-chairman. Geologist, The Texas Company, New York, N. Y. Basil B. Zavoico, Associate Vice-chairman. Geologist, The Chase National Bank, New York, N. Y. Engineering Research R. L. Huntington, Vice-chairman. Associate Professor, Petroleum Engineering, University of Oklahoma, Norman, Oklahoma. Economics Sidney A. SwensrUd, Vice-chairman. Assistant to the President, Standard Oil Co. (Ohio), Cleveland, Ohio. Refinery Engineering Walter Miller, Vice-chairman. Vice-president, Continental Oil Co., Ponca City, Oklahoma. 10

Jan 1, 1938

By Craig Ford

Inmet Mining is committed to implementing the highest corporate responsibility standards in its mining operations worldwide. Inmet is 100% owner of Minera Panama, a world-class copper project that is currently in the feasibility phase in north-central Panama. Panama has limited experience with modern mining, limited mining capacity, and the project context involves significant social, environmental and political complexity. The Project area is remote with recent in-migration of latino and indigenous people, informal and small-scale mining, local subsistence populations and considerable biodiversity value, coupled with a complex jurisdictional setting. In short, it is increasingly the kind of project mining companies are taking on because the easy projects have already been developed. With such challenging conditions, anticipating and managing social risks is critical to effective project management. To this end, between August 2007 and the third quarter of 2009 Inmet seconded Monkey Forest Consulting Ltd to the project to assist Minera Panama in building and implementing an effective, early phase external relations strategy. The team was also tasked to find and develop a locally based team that could sustain success through project development and into operations. Today?s presentation was created by Inmet and Monkey Forest and describes some of the lessons learned in implementing an effective early phase process for managing social issues.

May 1, 2010

By Bjorn Bolviken

Bjorn Bolviken (Geochemist, Geological Survey of Norway, Trondheim, Norway)-Under the heading "Recognition of Anomalies," the author states, "If the frequency distribution is actually log-normal, the probability of these high values being part of the background population is small (less than 0.023 and 0.0013 for 2 and 3 standard deviation, respectively)." The figures quoted seem to be the probabilities of these high values being the mean rather than part of the background population unless "background" is defined as one single concentration. If the background is considered to be a statistical distribution of concentrations,50 (which is probably the case here since the author uses the term "background population"), the probability of any observed value being part of the background may be estimated through a calculation of the number of observed values that are in excess of (or below) the number expected to belong to the background. Apparently, some confusion exists in the literature regarding this point. Many authors accept the concept of background as being a statistical distribution, but do not seem to recognize the consequences of this concept. One of these consequences would be that the background of a chemical element should comprise any concentration between zero and a theoretical maximum, which is governed by the chemistry and mineralogy of the material

Jan 1, 1974

By Levent Ozdemir

The advantages offered by mechanical mining have been demonstrated in the underground mining of coal, evaporites and other soft minerals. Mechanical mining and the advancements in automation technoloogies have been the principal drivers towards the realization of enhanced productivity in soft rock mining. For past two decades, emphasis has been placed on developing mechanical mining technology for hard rock applications, to achieve similar productivity improvements and cost reductions. The benefits of mechanical mining are numerous, particularly in an industry where market conditions continue to dictate higher production and lower costs while maintaining high safety standards. Other benefits of mechanical mining include reduced ground support and labor requirements and the elimination of blast and diesel fumes. These benefits further make this technology an attractive alternative to drill and blast for hard rock mining. Mechanical mining is conducive to full implementation of remote control and automation technologies that are under development to achieve further productivity and safety improvements in underground mining. Mine development has been the main focus area for mechanical miners by manufacturers and mining companies. Potential applications include ore body access, haulage and ventilation drifts, undercut and exploration drifts. The economic use of this technology in mine production is still considered many years away. It would need a major technological breakthrough that would make mechanical rock fragmentation competitive with the large-scale, low-cost production blasting operations.

Jan 1, 1998

By Keiichi Fujita, Katsumoto Ueda, Hiroshi Nakauchi, Naohiko Okumura

INTRODUCTION This paper presents (1) modified slipform system which was employed for simultaneous concrete placement for permanent lining and Instruction of a partition wall in the execution of a ventilation shaft 620m deep, and (2) current shaft sinking techniques which have been applicable and efficient for the subsurface conditions in Japan. MODIFIED SLIPFORM SYSTEM FOR PERMANENT LINING OF VERTICAL SHAFT General Information This paragraph deals with rapid construction by using modified slipform system for the permanent concrete lining and a partition wall of ventilation shaft, which has inside diameter of 620m and depth of 620m, of Enasan Highway Tunnel. The general feature of the shaft is illustrated in Fig. 1 and standard section of the shaft is illustrated in Fig. 2. The geological condition surrounding the shaft is mainly of ryolite and surface is of talus, but as a whole, they are rather weak and weathered rocks with faults, fissures and clay seams. 220mm borehole for the geological investigation was used as a drainage hole, predicting the amount of water inflow into the shaft to be 10t/min. The shaft was executed mainly by means of the conventional short step sinking method of 1.2m lift, employing temporary headframe and hoists. For each lift, 40 to 50cm thick temporary concrete lining was used. About 28,600m3 of rocks were excavated and

Jan 1, 1979

By J. S. Kirkaldy, R. J. Brigham

AS part of a program to investigate the diffusive properties of dilute ternary austenites we have made a determination of the effect of chromium on the activity of carbon in ? iron. Samples of pure iron and Fe-Cr alloys were simultaneously equilibrated at 1000°C with atmospheres of controlled CO/CO2 ratio following the procedures of Darken and Gurry 1 and smith.' The 0.020 in. thick samples were analysed for carbon by microcombustion analyses3 to yield a set of isoacti-vity curves. The latter were converted to activity coefficient (standard state at infinite dilution) plots by combination with Smith's data2 for the activity of carbon in pure iron. Table I shows the compositions of the base alloys used while Fig. 1 shows the experimental results superimposed on a set of curves generated by the relation In?C=6.9NC- 10.7 Ne In the notation of wagner4 the interaction parameter is the second coefficient on the right, Sgr = - 10.7 This can be compared with a rather inaccurate value deduced from the transient equilibrium diffusion data of Kirkaldy et al.' as The authors are indebted to the American Iron and Steel Institute for financial support. This material is condensed from a B.Sc. Thesis submitted to Mc-Master University by R.J.B.

Jan 1, 1963

By P J. Hansen, D G. Franklin, M E. Trim, J V. Myers

The Northern Sewerage Project (NSP) is an upgrade to one of MelbourneÆs ageing, under-capacity trunk sewers. It will reduce the volume and frequency of wet-weather overflows to the Merri and Moonee Ponds Creeks and facilitate new housing developments in the northern suburbs of the city. A total of 12.4 km of tunnel and eight vertical access shafts will be excavated as part of the two project stages: Stage 1 (NSP1) will be owned and operated by Melbourne Water (MW) and Stage 2 (NSP2) will be owned and operated by Yarra Valley Water (YVW). The owners require the project to have a service life of 100 years, a requirement significantly beyond many of the current Australian Standards, which aim to achieve service lives greater than 60 years but are typically assumed to achieve 40 to 60 years. Because of the potentially corrosive natures of the external environment along the tunnels and the internal sewer environment, durability was a key concern for NSP1 and NSP2. Stringent specifications were applicable to the tunnel lining systems. This paper describes the corrosive environments impacting NSP1 and NSP2, explains the key design differences between the two stages and details the lining systems considered and selected to achieve the clientsÆ desired 100-year service life. The project design is complete and construction began in 2007.

Jan 1, 2008

By Clamer, G. H.

G. H. CLAMER, * PHILADELPHIA, PA.-Unfortunately, prior to the war no serious attention was given to the conservation of tin, notwithstanding that this country is practically dependent upon outside sources for its entire tin supply. Tin is of vital importance in many industries, but it is surprising how many and how excellent are its substitutes when we become acquainted with them. Tin has always been a relatively high-priced metal, and it is part of the human attitude to associate high prices with high standards; it is not until the price of a commodity becomes well-nigh prohibitive that we hunt for substitutes, because the idea of substitution seems always to involve an assumption that the substitute must necessarily be inferior. The history of the development of bearing bronzes is a striking example of this policy. In the early clays, copper-tin alloys were almost universally used, the idea then being prevalent, which is still held by many, that a bearing to resist wear must be hard, and the harder the better. The favorite bronze bearing contained 90 per cent. copper and 10 per cent. tin; frequently, in service which was considered severe, even higher proportions of tin were used.. Such hard alloys have great resistance to compression, but as a rule they had a very wide factor of safety in this

Jan 12, 1918

By Thomas C. Anderson, Terry Weiss

The Mount Gunnison No. 1 Mine of the West Elk Coal Company (wholly owned subsidiary of ARCO Coal) had secured contracts to provide low sulfur, high Btu steam coal to various utility companies. This called for the development of the B-Seam at the Mount Gunnison Mine located some 400 feet below the operating F-Seam workings being mined with conventional room and pillar techniques. The B-Seam, to meet production goals, will be mined by a new 600-foot longwall machine making a 13-foot high cut. American Mine Services was awarded a competitively bid contract to drive two 2000-foot, 13-foot by 16-foot slopes at -15 percent, sink a 16-foot diameter ventilation shaft 400 feet between the F- and B-Seams, install a 60-inch conveyor in one of the slopes, remove 7000 feet of existing conveyor and rehabilitate 7000 feet in two entries to accommodate the placement of the longwall machinery. The slope portals were located 7000 feet in by the surface portal. Unique to the project was the placement of work shops and other infrastructure 7000 feet underground with an entry height of 6 feet. The $7 million contract was completed in less than one year using a mix of permissible (Schedule 31) and standard (Schedule 24) LHD equipment, all pneumatic jumbos and shaft sinking gear.

Jan 1, 1993

By A. W. Hahn

THE importance, to geologists and metallurgists, of knowing the mineralogical forms in which the silver occurs in ores has increased during the past few years, and will continue to increase as long as working hypotheses are converted into proved theories and rule of thumb methods are supplanted by scientific data. The methods used for the determination of these silver minerals have been: (1) careful study of polished ore sections with the microscope, and more recently, (2) metallurgical separation of the ground ore by flotation, tabling and panning, supplemented by microscopic examination of these separated minerals, and chemical analyses. During the course of some experimental work carried on by the testing department of the International Smelting Co. and myself, it becomes important to determine, in a general way, the distribution of the silver values in the minerals, as they exist in Tintic Standard and North Lilly siliceous oxidized lead-silver ores. These mines are in the East Tintic Mining District, State of Utah. In this work the second method was used. Differential flotation tests were run, separating the sulfide from the oxidized minerals, and the products were assayed. Various concentrates were carefully panned and the separated products assayed; special samples of ore were selected and assayed. The microscope was used only for the purpose of determining whether the individual minerals were in the so-called "free" state.

Jan 1, 1929

By E. H. Cho, Q. Luo

Pittsburgh No. 8 coal, cleaned by conventional froth flotation, was oxidized in a 2-L Parr stirred bench-top autoclave. Autoclave tests were carried out for up to 5 hrs under the following conditions: 150 to 225ºC, 60 to 500 psi 02 and 15 to 60 g of coal per 600 mL of distilled water. The oxidation of coal was evaluated by measuring the total acidic group formed on the surface of the coal and by measuring the adsorption (under standard conditions) of calcium ion from a solution. The degree of oxidation of the coal increased continuously, without much leveling off, with increasing oxygen pressure. With increasing temperature, the oxidation of the coal increased sharply between 150 to 175ºC and then leveled off above 175 °C. The adsorption of calcium was >3% on coal oxidized under the most favorable conditions. The adsorption of calcium on coal increased sharply with increasing equilibrium pH. The loss in Btu was found to be sensitive to oxidation temperature. This study concluded that the optimum oxidation of coal is achieved over 3 hrs at high oxygen pressures (e.g., 500 psi) at ~170ºC. This study also concluded that, when measured in terms of calcium adsorption, Btu loss and reaction time, the oxidation achieved in an autoclave is far superior to that achieved in a fluidized bed.

Jan 1, 1996

By W. C. Winegard, C. J. Beinjessner

PREVIOUS investigations 1,2 of Fe3P described by pearson3 and schubert4 show that Fe3P has a bct unit cell having four Fe3P tetrahedra centered around each lattice point. The space group is 14, No. 82, and all atoms occupy general positions 8(g). The cell dimensions3 are: a = 9.090, c = 4.446 kX, with an axial ratio of c/o = 0.4891. We have measured the lattice parameters of Fe3P, using a Fe as an internal temperature standard, at 23°, 414°, and 678°C and computed the thermal expansion over this temperature range. The Fe,P was prepared by melting under vacuum (after flushing with argon) a commercially pure iron and "ferrophosphor" in a high-frequency induction furnace. Part of the ingot was crushed for X-ray examination and for chemical analysis. X-ray diffraction and light microscopy indicated iron phosphide (Fe3P) present as the major constituent and a small amount (about 5 pct) of a Fe. Chemical analysis showed 0.05 wt pct Si, 0.008 wt pct N, 0.018 wt pet C, and less than 0.02 wt pct each of other metallic elements. X-ray diffraction powder patterns were obtained from a mixture of iron and Fe3P sealed in an evacuated quartz capsule using a Unicam high-temperature

Jan 1, 1968

By B. C. Craft, T. J. Johnson, H. L. Kirkpatrick

Petroleum engineers are displaying considerable interest in the problems of cementing oil wells, especially in the Gulf Coast and California areas, where steep temperature gradients are encountered and where wells are being drilled to greater depths. Deep drilling, that is, at depths in excess of 7000 ft., has been undertaken in these areas only in the last few years and with this trend oil-well cementing requires more technical treatment. It is not the purpose of this paper to describe the scope and application of cement operations in the oil industry or to give the standard specifications, methods of sampling and testing of portland cement. The various testing methods have been described by the American Society for Testing Materials1, Uren2, Tickell and Wankowski3 and Rakestraw and Parsons4. The latter authors (pp. 50-58) have also described in detail the methods of cementing. The authors realize that it is impossible to reproduce in the laboratory the scale of forces and dimensions that exist at great depths, but an attempt has been made to scale down these dimensions proportionally. The selection of problems to be studied was based largely upon the practical questions asked by several of the largest operators in these fields. All cements used in these experiments met the specifications of the American Society for Testing Materials.

Jan 1, 1935

By Milton C. Head, Aulton E. Roland, William E. Hawes

INTRODUCTION Uranium mining in the Grants Mineral Belt has undergone changes from methods pioneered during the 1950's and has now become fairly standardized throughout the district. The orebodies vary in size and shape and have been most successfully mined by using modified room and pillar methods with pillar recovery. This paper will expand on methods and equipment that are being used and modifications of these that will increase productivity and efficiency. GEOLOGICAL BACKGROUND The petrology of the Grants Mineral Belt consists of alternating layers of sandstone and shales (mudstone), with occasional thin layers of coal. The sandstones are aquifers which are generally artesian to some extent. The shales are bentonitic and decompose into extremely sloppy mud when exposed to water. Figure 1 shows a typical geologic section. Most of the uranium produced in the Grants Mineral Belt comes from the Westwater Canyon member of the Morrison Formation and occurs as scattered ore bodies throughout the formation. This formation consists of layers of bentonitic shale and sandstone of varying degrees' of cementing and grain size. It is also a very significant artesian aquifer. The unconfined compressive strength of the various formations is not high, as shown in Table I. It is important to note that these represent average values and a great range may exist within a single formation, especially In the Westwater which is the ore formation. [ ]

Jan 1, 1982

By Z. T. Bieniawski, E. Unal, H. Reginald Hardy

INTRODUCTION Rock bolts are a major means of support in underground coal mines in the United States. However, two of the most crucial problems facing the mining engineer today are that of finding a well defined and standard method for testing the anchoring ability of rock bolts, and of selecting the most suitable type of rock bolt and bolting pattern for a particular mine or specific mine section (Anon., 1982). Such selection requires not only an understanding of the behavior of the rock mass and the rock-bolt unit itself, but also a knowledge of the basic mechanisms by which rock bolts provide support while they interact with the rock mass during various field loading conditions. A recent study in this area has shown the inadequacy of present methods used in selecting and testing of rock bolts and the lack of clearly defined guidelines for safe and economical design of bolting patterns (Bieniawski, et al., 1980). The present paper describes a research study aimed at developing laboratory instrumentation and associated techniques for the evaluation of bolt-rock interaction. The instrumentation system developed, procedures followed during various experiments, and typical results from a series of studies carried out on mechanical bolts are presented. DEVELOPMENT OF THE ROCK BOLT TESTING FACILITY General A block diagram of the experimental facilities are shown in Fig. 1. The system consists of three main sections. The first

Jan 1, 1982

Weiss Transit and Level The illustrations shown are the transits and levels manufactured by the Weiss Instrument Co. of Denver, Colo:, and they state that city and mining engineers are securing satisfactory results. It is claimed that their patented prismatic telescope gives increased illumination with an astronomical eye-piece. The prisms are set in a milled seat for this purpose, and cemented in so they can never come loose or out of adjustment. All adjustment for collimation is clone with the cross-hairs. This telescope is 8 in. long for magnifying power of 20 diameters against 12 in. for regular old style. The field is 1° 45' with a clear aperture of 1 1/8 in. The standards are 4 ¾ in. high from plate; to center of telescope axis. Weight 10 lb. Fig: 2. FIG. 1. FIG;. 3. The Light Mountain Transit of the same type, Fig. 1, has a telescope 6 ½ in. long, magnifying power 17 diameters; field 2° 15'; clear aperture 1 1/16 in.; weight 9 lb. The Mine Transit made by this ?company is interesting because it may be sighted directly down a shaft.. The principal advantage claimed for this type is the arrangement by means. of which vertical' sights can be had without an additional telescope.. As illustrated in Fig. 2 the telescope is in the position of a regular transit, and used exactly the same.

Jan 10, 1915