Search Documents

By J. H. Slater

THERE is nothing particularly new about the use of sinter in a blast-furnace burden. For many years flue dust has been sintered at the various blast-furnace plants to put it in a form that could be recharged to the furnace with some assurance that it would stay in the second time. This paper is not a compilation of scientific data but only an attempt to give our experience with sinter. There are some unexplained discrepancies in the tests given here, such as the flue dust produced and iron tonnages, but the results given are the results that were obtained. Sinter is not the cure-all for blast-furnace problems. A good coke is still the most important factor in good furnace operation. However, good sinter is a big help. As flue dust is produced under varying operating conditions and fluctuates greatly in carbon content, it is difficult to produce from flue dust alone a uniform sinter, which will give satisfactory blast-furnace results. Sinter made from flue dust alone will change in character with every carbon variation. Almost invariably flue dust con-tains carbon in excess of the amount necessary to make good sinter, and this excess must be burned out, This, of course, necessitates reduction of the speed of the sintering machine and thus a decrease in tonnage, An alternative is to dilute with a carbon-free material to use up the excess carbon. High-carbon material when sintered results in a very dense, undesirable prod-uct, since the excess heat melts the charge into a hard, nonporous mass, and tends to form refractory silicates.

Jan 1, 1940

By R. D. Nelson

The purpose of this technical note is to briefly present some data on a phenomenon—recrystallization with concurrent deformation—that has been found to occur in a plutonium. This phenomenon is unusual because a plutonium is considered brittle, not easily deformed, and not easily recrystallized; the a phase is simple monoclinic having 8 atoms per unit cell and it is stable below about 115°C. The properties of the recrystallized metal were different from the as-cast metal. Even though a plutonium is difficult to deform, Ianniello successfully rolled it' and he also observed some recrystallization at 120°C.2 Pavlick and Hanson3 detected some recovery at 109°C but they observed no recrystallization. Gardner4 and Bronisz5 studied the compression properties up to 100°C but they did not report having seen recrystallization. In the present deformation studies of electrorefined plutonium pronounced recrystallization took place concurrently with plastic deformation in compression between 24" and 115°C. The metal contained less than 300 ppm total impurities with the major impurities being 100 ppm Am, 30 ppm C, 40 ppm W, and 25 ppm U; all other impurities totaled less than 100 ppm. The compression specimens were machined to dimensions of 1.2 cm long and 0.8 cm diam from as-cast rods having a density of 19.65 g per cu cm. They were heated to the test temperature in a high-temperature silicone fluid that was evacuated to 10-4 Torr. With this procedure the specimens oxidized a negligible amount, and the temperature was maintained within ±0.2°C for times up to 3 weeks. Deformation and recrystallization

Jan 1, 1969

By F. C. Newton

REFINERS of lead by the Parkes process have always been solicitous of recovering the zinc used in the desilverization, and justly so, as the loss in zinc constitutes one of the heavy costs in this method of refining. Part of this loss is due to the absorption of zinc by lead, and in the present state of knowledge is not recoverable as metallic zinc. The remainder of the zinc, which finds its way into the precious-metal-bearing crust, is recoverable and naturally engages the operators' most exacting attention. Careful elimination of the impurities in base bullion has enabled the refiner to produce a zinc crust better adapted to retorting, which reflects favorably in the zinc recovery; and to produce a richer crust, thereby lowering the zincking cost, as the increased efficiency of the zinc results in less of it being in circulation. It is obvious that if the ratio of concentration be increased, a lessening of the amount of crust formed will ensue, throwing less work on the retorts and diminishing the amount of retort metal sent to the cupels, thus making an actual money saving in all these operations. In the effort to obtain a rich crust, the metallurgist has increased the heat to a considerable degree, upon the assumption that at the higher temperature the zinc-silver alloy could be squeezed free from the adhering lead. A further possibility for improvement suggested itself in the freezing-point curve of Prof. H. C. Carpenter, upon zinc and silver. Study of this curve disclosed the existence of a definite chemical compound, . Zn3Ag2, with a freezing point of 665° C., a promising compound for practical application.

Jan 2, 1915

By N. W. Shed

The specifications for bridge-steel are usually not severe. The main difficulty is to secure a material which will roll easily, without showing signs of cracking on the corners of the blooms or on the flanges of the beams. In many mills sulphur has been deemed the most harmful constituent in this respect. It has been thought hazardous.to roll steel containing over 0.07 per cent. of sulphur. Yet, in making steel for the Phoenix Iron Company, I have produced from stock running as high as 0.13 per cent. of sulphur a material which rolled very satisfactorily. It is reasonable to infer that the injurious effect of sulphur can be neutralized, to a great extent, by proper treatment in the open-hearth furnace; and the following notes from my usual practice here may be of interest to those obliged to use high-sulphur stock. The steel made at Phoenixville in the 20-ton furnaces has about the following composition : Per cent. Carbon,...0.15 to 0.20 Manganese,.........0.50 to 0.60 Sulphur,..........0.11 to 0.13 Phosphorus,.: .0.04 to 0.06 Silicon,.......... 0.01 to 0.02 The best running heats were made with a small amount of pigiron. In using large proportions of pig the quantity of ore is also increased. This not only cuts the bottom, but also lengthens the time required to bring the charge down. Up to 50 per cent. of pig may be used, but 25 per cent. is much better. A 40,000-pound charge, containing 10,000 pounds of pig and 30,000 pounds of Bessemer butts or beam-scrap, works very well.

Jan 1, 1890

This discussion of the paper of Chester W. Washburne should have been printed following the remarks of H. A. Wheeler, in Bulletin No. 100, April, 1915, pp. 835 and 836, but was inadvertently omitted. ROSWELL H. JOHNSON:-There is one reason why the hydrostatic interpretation of gas pressure is not wholly acceptable. As we go clown in the sands we seem to get excesses of gas. Particularly in this field it becomes excessive in quantity relative to the amount of water in the sand. If this holds in other fields as well it must mean that there has been an ascension of water, because these sedimentaries when laid down, were filled with connate water. If we do get an ascension of connate water, produced by some such phenomena as its expansion by heat or by the formation of new gas by pressure upon organic materials at great depth, we can hardly expect the pressure to be controlled merely hydrostatically. * In reply to Mr. Wheeler's inquiry as to gas wells with pressure higher than hydrostatic pressure, I would cite the original wells given by Orton on which he based the hydrostatic theory. He used in his calculation a head of 600 ft. above tide, assuming the outcrop of the Manitoulin Islands to be in Lake Superior, whereas the Trenton does not outcrop at Lake Superior. The Manitoulin Islands are in Lake Huron, the level of which is 580 ft. above tide. No allowance is made for the lower density of the fresher water near the outcrop, the weight taken for the whole column being the water of high density found at the wells.

Jan 5, 1915

By M. A. Quader, D. Kuhlmann-Wilsdorf, R. A. Dodd

STACKING fault tetrahedra were first observed in quenched and aged pure gold by Silcox and Hirsch1 and identified as defects originating in the collapse of vacancy discs on {111} planes. It was supposed that sessile loops are the first product of the collapse, and that by a dislocation dissociation/glide sequence these are converted into tetrahedra. Although the tetrahedra can be mechanistically accounted for in this way, recent investigations indicate that their growth occurs by the absorption of individual vacancies on small nuclei involving perhaps as few as six vacancies.2-7 Besides stacking fault tetrahedra, triangular and crystallographic shaped Frank loops, although fewer in number, have always been observed in quenched and aged gold.19798 It is not known definitely whether these loops form from collapsed tetrahedra. The fact that the Frank loops are usually larger than the accompanying tetrahedra might indicate that the loops grow independently by absorbing vacancies, but this does not rule out the possibility of the collapse of tetrahedra into loops under all circumstances. Silcox and Hirsch1 have actually observed under the electron microscope tetrahedra collapsing into loops, probably due to stresses set up by the heating of the specimen by the electron beam. The energy residing in the stacking faults of a tetrahedron is proportional to the square of the edge length, while the energy of a triangular perfect dislocation loop depends on its edge length, L, as const L ln(L/ro). Therefore, beyond some critical size tetrahedra must become unstable with respect to collapse into triangular loops.1,3,8-11 However, it seems that in the absence of strong stresses tetrahedra usually decay by the

Jan 1, 1969

By Victor F. Hollister

This section includes examples of discoveries of Kuroko- and Anyoz-type massive sulfides, and shale-hosted, zinc-lead deposits, and describes exploration models for each group of case histories. Exploration or empirical models can differ from genetic models, because ore guides and controls are emphasized in exploration models. Genetic models may form the scientific basis for exploration or prospecting models, although factors that are important to the localization of ore are stressed in exploration models. The paper by Sato (abstracted herein) on Kuroko deposits can be used as a general exploration guide for that type of deposit. It is clear, however, that no unambiguous stratigraphic control for Kuroko-type ore is given in the Sato paper. The paper by MacIntyre (an excerpt herein) describing Gataga, Midway, and Windy Craggy includes most of the elements of the shale-hosted and Anyox models. Although more recent work by the Geological Survey of Canada has modified the Windy Craggy stratigraphy, the Anyox model as applied to Windy Craggy is well described in the MacIntyre (1983) paper. Discoveries of ophiolite-, Ducktown-, volcanic-associated Ni- Cu-, and Besshi-type deposits are not included in this section. Conformable massive sulfide deposits are generally assumed to be syngenetic. Sulfides in the crosscutting feeder zones, however, are classed as epigenetic. Therefore, volcanogenic massive sulfides can contain both a syngenetic and an epigenetic component. Vital to the development of the epigenetic component is a heat source that propels the convection cycle that forms both components. In all massive sulfide discoveries described in this section, it is assumed that a volcanic magma fueled the hydrothermal fluids.

Jan 1, 1991

By W. H. Fitch

HAVING been asked to make some remarks after the reading of Mr. Dyrssen's paper, I regret that a test started some months ago has not yet been completed, but some of the things which I can tell you at this time seem interesting and shed a little different light on the idea of a recuperator. The device referred to is becoming more than. a recuperator, largely taking the place of a regenerator. I assume there is familiarity with the sketches that I presented in October, 1926, before the Engineers' Society of Western Pennsylvania, describing our re-cuperator combination with checker chambers, and I have additional ones to show at this time. The follow-ing remarks will deal with modifications that have been made. At that time I suggested the gases leaving the regenerators at, say, 1400°, be reduced to 500° F. The opinion of the operating men consulted since that time is that, under the best operating conditions, the tem-perature may be 750° to 800° F. after the recuperator and on entering the stack. While the lowest final temperature of the gases en-tering the stack is important from the economic stand-point of fuel burning, and operating in general, it is not the whole story. The method of getting the heat out of the checkers is important. It is believed by many with whom we have talked that a better way is by a combination of checkers and a carborundum re- cuperator of the type described as it will stand all tem-peratures met in practice and might be called a super-refractory.

Jan 1, 1928

By William R. Webster

At the Florida meeting of the Institute, in March, 1895, I presented a Note on a Proposed Scheme for the Study of the Physics of Cast-Iron,1 giving an outline which, for convenience of reference, I here repeat. Suggested Lines for DiScuSsion and IvestiGation. I.—Correspondence between chemical composition and melting-point, fluidity, shrinkage, fracture, chill, micro-structure, and other physical properties. II.—Influence of: 1. Cupola-mixture, use of steel and other scrap, oxidized or clean material, 2. Manner of melting, flux, etc., 3. Casting-temperature, A. Fracture. 4. Manner of handling melted metal and B. Micro-structure. method of casting, C. Physical properties. 5. Size and form of casting, D. Shrinkage. 6 Kind of mold, green sand (under dif- on E. Chill. ferent conditions of ramming, amount F. Residual strew of moisture, and skin-dried), dry sand, G. Condition and quan- loam, and chills, tity of carbon and 7. Rate and mode of cooling castings, other elements. 8. Manner and temperature of heating for annealing, 9. Additions of nickel or aluminum, III. —-Segregation as affected by : 1. Composition ; 2. Casting-temperature; 3. Rate of cooling ; 4. Size and shape of casting. IV. —Blow-holes, their volume and position as affected by: 1. Composition; 2. Casting-temperature; 3. Casting-pressure ; 4. Rate of cooling; 5. Size and ehape of casting ; 6. Special additions. It was hoped that a discussion might thus be elicited, similar in interest and value to the discussion of the physics of steel, which had been so widely and gratefully welcomed by students and practitioners in that department. That this hope was not

Jan 1, 1905

By S. J. Schatzel, J. D. Addis, V. Gangrade

In longwall mining, ventilation is considered one of the more effective means of controlling gases and dust. In order to study longwall ventilation in a controlled environment, U.S. National Institute for Occupational Safety and Health (NIOSH) researchers built a unique physical model called the longwall instrumented aerodynamic model (LIAM). The LIAM is a 1:30 scale physical model geometrically designed to simulate a single longwall panel. It has an 8.94 by 4.88 m (29 by 16 ft) footprint with a simulated face length of 220 m (720 ft) in full scale. LIAM is built with critical details of the face, gob and mining machinery, and scaled to preserve the physical and dynamic similitude. This paper discusses the gob-face interaction, airflow patterns within the gob, and airflow dynamics on the face for varying roof caving characteristics. Results are discussed to show the impact of caving behind the shields on longwall ventilation.

By R. M. Zimmerman

INTRODUCTION Tuff is being considered as a possible geologic median for the underground storage of commercial high level radioactive wastes by the Department of Energy (DOE). DOE has the responsibility for developing or improving the technology fir safely and permanently isolating these wastes. DOE programs must satisfy requirements established by the Nuclear Regulatory Commission (NRC) for the licensing and regulating of these storage facilities (NRC 1981). Pertinent draft NRC requirements are: 1) releases of radioactivity to the environment must be within prescribed limits and 2) emplaced canisters containing wastes must be retrievable up to 50 years following emplacement. High level radioactive wastes produce heat in storage and it is essential that the thermal/mechanical/hydrological response of the host rock will not significantly degrade either the structural performance o£ the repository or the ability of the natural or engineered barriers to retard radionuclide migration. The Nevada Nuclear Waste Storage Investigations (NNWSI) was established by DOE to evaluate the suitability of disposing of high level nuclear wastes on or near the Nevada Test Site (NTS) (NNWSI 1980). NNWSI has focused exploration and site evaluation on the tuffs of Yucca Mountain. Field testing is essential to support site characterization and repository design efforts. Preliminary studies have been conducted indicating that tuffs in G-tunnel on the NIS contain welded and nonwelded tuffs that have similar properties to those in Yucca Mountain. Thus, field testing can be accelerated. This paper discusses the issues supporting the planned field experiments in G-tunnel. Issues not related to rock mechanics are not included.

Jan 1, 1982

By Gregory Dybalski

The purpose of this paper is to illustrate the forecast capability of the econometric model of the cobalt industry1/ as utilized by the Federal Preparedness Agency. Forecasts from this model are illustrated from the premise that the leading producer continues production of cobalt. An alternate forecast is presented where the model structure is altered to reflect the condition where the leading producer leaves the market. All estimations and forecasts presented here are shown for illustrative purposes. The cobalt industry is highly concentrated; one company, owned by the Zaire government, accounts for approximately three-fifths of world production. The cobalt supply outside of Zaire is determined by the level of activity of copper or nickel markets, as cobalt is mined as a by-product of copper or nickel. The demand for cobalt reflects a diversified usage pattern; cobalt is used mainly in heat and corrosion-resistant materials, high- strength materials and permanent magnets. According to 1974 U.S. consumption data superalloys accounted for 22%, magnetic alloys 18%, cutting and wear-resistant materials 13%, and catalyst 7%. Foreign consumption is probably similar in terms of usage categories, but the relative order of the categories is in variance.2/ The Cobalt Model The cobalt model's object is to explain consumption, supply and price movements by utilizing statistically estimated equations. Central to the econometric model is the role of Zaire as the profit-maximizing "dominant firm". Zaire sets the price that is most profitable for itself. The price of cobalt depends on industrial demand, production of other firms, and net exogenous purchases, such as government

Jan 1, 1977

By Shadia J. Ikhmayies

"Cadmium sulfide thin films were prepared on glass substrates by the spray pyrolysis technique at a substrate temperature of 490°C. Some of the films were etched by HC1 in distilled water, others were heat treated in nitrogen atmosphere, and another set of films was first etched by HC1 and then annealed. Room temperature impedance spectroscopy measurements on the films were performed using coplanar geometry in the dark and in room light in the frequency range 20 Hz to 1 MHz. The experimental data were represented by complex plane diagrams and showed one well-defined semicircle in the high frequency region. Hence the equivalent circuit that models the CdS: In thin films was found to be a single RC circuit, which indicates the bulk conduction through the grains. The influence of treatments on the electrical properties was investigated.IntroductionCadmium sulfide (CdS) is a brilliant II—VI semiconductor material with a direct band gap of 2.42 eV at room temperature. It has many outstanding physical and chemical properties, which have promising applications in multiple technical fields including photochemical catalysis, gas sensor, detectors for laser and infrared, solar cells, nonlinear optical materials, various luminescence devices, optoelectronic devices and so on [1]. There are different methods to prepare undoped and doped CdS films, such as rf sputtering [2] chemical bath deposition (CBD) [3], pulsed laser deposition (PLD) [4], and spray pyrolysis (SP) [5-11]. Of these methods, spray pyrolysis represents the less expensive option, and can produce large area high-quality low cost thin films [12]."

Jan 1, 2012

By Frank Fahrenwald

INTRODUCTORY A COMPLETE list of the elements as given for 1915 includes 18 that melt above 1,700° C. There does not exist one complete thermal equilibrium diagram for any pair of these 18 elements. Several of these elements have been combined, in relatively small proportions, with metals of lower melting point: e.g., tungsten, molybdenum, and vanadium, in steels, or with nickel and cobalt; but of this refractory group, platinum is the only one that has been extensively studied in this connection. When one considers that, with few exceptions, the industries have made use of alloys to the exclusion of pure .metals, it is reasonable to expect that alloys of this refractory group will invade fields in which the pure metals have found little application. The past neglect of this class of metals has, no doubt, been partly due to the rarity of some of them, for even though alloys of very valuable properties should be developed, their cost, unless in exceptional applications, would be prohibitive. There is also a well-founded reluctance to undertake research involving very high temperatures which, in the case of most of these elements, must be accompanied by an inert atmosphere as well. This combination of high temperatures* and control of atmosphere within the heating chamber of any furnace of present design is a difficult problem. It is the purpose of this paper to give results,1 of an investigation of one binary series of this group, in which methods were employed that avoided the usual difficulties accompanying high-temperature alloy investigation.

Jan 6, 1916

By John W. Tieman

Coal is a term applied to vegetable matter (trees, grasses, etc.) which was subjected to heat and pressure through geologic ages. This resulted in a change in both the physical and chemical properties. Because its chemical composition is variable, geologists classify coal as a heterogeneous mineral rather than a homogeneous mineral. Peat represents the initial, unconsolidated stage in the development of coal. This coalification continues with time and the application of temperature and pressure to lignite, subbituminous, bituminous, and anthracite toward the theoretical graphite end member. PHYSICAL PROPERTIES OF COAL The physical properties are concerned with the characteristics of coal in its natural state, or prior to its end use as a fuel. For example, the hardness and grindability of coal determine the maintenance cost for coal mining, handling, and pulverizing equipment; the specific gravity of coal and its associated minerals determines the coal preparation technique used in a cleaning plant as well as the capacity of coal bins, boats and size of cargo, and other coal storage facilities. The physical properties are, of course, dependent on the chemical constituents of coal, and all properties are interrelated. Specific Gravity The specific gravity (sp gr) of a solid is the ratio of the weight of a cubic foot of the solid to the weight of a cubic foot of water. The specific gravity of pure coal has been reported to range between 1.23 to 1.72 and increases with the change in rank from lignite to anthracite. This means that it is 1.23 to 1.72 times heavier than water.

Jan 1, 1981

Discussion of the paper of J. V. EMMONS, presented at the Pittsburgh meeting, October, 1914. and printed in Bulletin No. 93, September, 1914, pp. 2233 to 2248. ALBERT SAUVEUR, Cambridge, Mass.-Mr. Emmons is to be congratulated for having placed before us in so forcible and satisfactory a manner a question of much importance-that of the surface decarbonization of steel. Of course, both manufacturers and consumers have known for many years that during the heat treatment of high-carbon steel, surface deca.rbonization is always likely to occur to a greater or less degree, but the subject does not seem to have been investigated with the method and thoroughness it deserves. I am in substantial agreement with Mr. Emmons's conclusions, and I have but little to add to what he has so well said. His statement that carbon dioxide is just as effective an oxidizing agent as pure oxygen is likely to cause surprise and some will wonder whether his investigation has been carried far enough to warrant so unexpected a conclusion. The reaction C + 0 = CO, expressing the oxidation of carbon by pure oxygen, is decidedly exothermic, whereas the reaction C + C02 = 2C0, expressing the oxidation of carbon by carbon dioxide, is endothermic. Decarburization by pure oxygen, therefore, should take place much more readily than by carbon dioxide. One cannot help regretting that the author does not mention' the best way of preventing in a practical manner surface decarbonization while treating tool steel and other high-carbon steels.

Jan 4, 1915

By C Li

Removal of gangue minerals from ilmenite concentrates can beaccomplished by relatively low temperature roasting in controlled gasatmospheres to selectively enhance the magnetic separationcharacteristics of the ilmenite. At roasting temperatures below 800¦C the magnetising reactions are often not consistent with phase equilibria considerations. Metastable phases can nucleate and control the roasting products. In weathered ilmenites the phase assemblages and microstructures in the altered ilmenite grains can influence the roasting reactions. In this paper we give an overview of the phase chemistry of chemically weathered ilmenites and of metastable phases formed by low temperature roasting. We also report the results of roast experiments conducted in a neutral gas atmosphere. Major increases in magnetic properties after short roasting times at low temperatures were obtained for a range of ilmenite concentrates. For example heating a secondary ilmenite concentrate from Western Australia for 15 minutes in nitrogen at 600¦C gave an increase in the three kilogauss magnetic fraction from three to 92 wt per cent. The solid state phase changes accompanying the inert atmosphereroasts were characterised by combining elemental analyses withquantitative phase analyses of the ilmenite concentrates and their roast products. It was found that the phase reaction that is principally responsible for the increase in the magnetic properties of weathered ilmenites involves a transformation of disordered ferrous-containing pseudorutile to an ordered ilmenite-hematite solid solution containing typically ten to 35 mole per cent of the hematite component. Examples are given of the application of the inert atmosphere roast to effect separations of ilmenite from gangue minerals.

Jan 1, 2001

Economic Significance of High-grade Concentrates BY PAUL M TYLER AND CARLE R HAYWARD (Min & Met, Dec, 563 4000 words) Generally pyro¬mctallurgical methods yield a higher recovery but cost more per ton of ore treated Milling methods are inherently cheaper for the reason that they do not involve dissipa¬tion of heat energy in slag formation, ctc It is vaguely realized that the smelter man could do a better job if he were supplied with purer raw materials but hard¬headed mill men have been offered little inducement to do a really good job of cleaning concentrates To do this may involve some sacrifice in percentage yield and in mill capacity and unless there is a compensating saving in freight and smelter charges, it simply is not good business to go beyond a certain point in the way of making clean concentrate Opportunities exist for eliminating one or more steps in the expensive series of processes for recovering various metals, or at least reducing the volume of materials that has to be handled at the most costly steps The beneficiation of nonmetallic minerals likewise affords numerous examples of over-all economies obtainable through more refined methods of mechanical improvement All this leads to the conclusion that perfecting selective processes for isolating pure minerals (e g, galena) virtually free from other sulfides as well as gangue may be productive of industrial economies Conversely, cheapening smelting methods may invade the field of mechanical improvement of ores but, as Kiphng said, that is another story

Jan 1, 1937

By Laurentiu Nastac

"This paper describes the development and validation of a comprehensive multiscale modeling approach capable of predicting at the mesoscopic scale level the ingot solidification structure and solidification-related defects commonly occurring during the vacuum arc remelting (VAR) process. The approach consists of a coupling between a fully transient macroscopic code and a mesoscopic solidification structure code. The predictions from the multiscale model, including grain morphology and size, primary and secondary dendrite arm spacings, Laves and NbC phases, tendency for freckling and columnar-to-equiaxed transition, were validated against experimental measurements for a 20-inch diameter VAR alloy 718 ingots. The validated model was then used to investigate the effects of melting rate and ingot diameter on the solidification structure of VAR processed 718 ingots.IntroductionThe objective of this work was to develop a fully transient multiscale modeling approach to get an insight into the effect of processing parameters on the cast micro- and macro-structure during VAR processing. The developed model assists in achieving better control of the ingot solidification structure and to determine trends in the macrosegregation in these ingots. Another objective of this work was to analyze the transient effects of production rate and ingot size on the resultant ingot microstructures. This objective was met by first understanding the effects of the full range of processing parameters typically used in the VAR process. Processing parameters such as power input and heat extraction rate significantly influence the ingot liquid pool size and shape as well as the ingot structure, which in turn will greatly impacts the final ingot quality."

Jan 1, 2012

By J. Manchisi

Laboratory investigations were conducted to establish the feasibility of bioleaching a mixed copper oxide/sulphide rougher concentrate from Nchanga Mine on the Zambian Copperbelt. The objective was to determine the kinetics and extent of copper extraction for this material. Batch experiments were conducted under different solution conditions in stirred tank bioreactors. The progress of (bio)leaching was monitored through measurements of soluble ferrous and ferric iron, copper, pH, and redox potentials, while bacterial activity was monitored online through 02 and C02 gas utilization rates. About 20 per cent copper was solubilized within 2 hours in all cases of non-oxidative (abiotic), oxidative (abiotic), and bioleaching experiments. This was attributed to the dissolution of mainly copper oxides. Subsequently, bioleaching experiments resulted in an overall copper extraction of 93 per cent, with up to 8 g.L-1 copper after six leaching days, compared to 58 per cent copper extraction in the abiotic oxidative acid leaching experiments. However, there was little effect of time (i.e. poor dissolution kinetics) on copper recovery for abiotic non-oxidative acid leaching of the material. Hence, the rate of sulphide leaching increased due to the activity of bacteria. Thus, the material is potentially bioleachable under mesophilic conditions. However, more exhaustive test work needs to be conducted to establish the effect of bioleaching variables and heat requirement.

Jan 1, 2012