Search Documents

By N. A. Barcza

An investigation was conducted into the reactions between the slag system MnO-CaO-MgO-SiO2(AI2O3) and the alloy system Mn-Fe-Si-(C). Synthetic slags representative of plant melts and a plant alloy were reacted in alumina crucibles at temperatures of 1400°C, 1450°C, 1550°C, and 1600°C. In similar experiments, slags were used that comprised a South African manganese ore with various amounts of lime and several synthetic alloys with various silicon contents and manganese-to-iron ratios. These experiments were conducted in a vertical molybdenum-wound resistance furnace with full temperature control. Slag-to-alloy ratios were also varied during the tests. The rate of reduction of Mn.O3 and the MnO from the slag by the silicon in the alloy was extremely rapid, most of the reaction being completed within five minutes. The strongly exothermic nature of the reaction resulted in considerable generation of heat at the slag-alloy interface, causing convectional stirring of the contents of the crucible and promoting the rate of reaction. Equilibrium was usually attained after fifteen minutes. The major limitation governing the recovery of manganese is the need for the silicon content of the alloy to meet a maximum specification of 2 per cent. Higher concentrations of silicon in the final alloy of between 8 and 12 per cent favour good recoveries of manganese from the slag, but, since such an alloy is not salable, lower recoveries must apparently be tolerated. In alloys of 2 per cent silicon, low activities of the silicon are responsible for poor recoveries of manganese. The activity of MnO in the slag can be increased by moderate additions of CaO and small amounts of MgO, i.e., by an increase in the basicity of the slag.

Jan 1, 1979

By T. Sterry Hunt

THE essential principle of this new process, now in operation in Chili and in North Carolina, for the extraction of copper from its ores, is the dissolving of the oxides of copper by a hot solution of protochloride of iron and common salt. In the action which takes place, the protochloride of iron is converted into peroxide, while the oxides of copper are changed into protochloride and dichloride, the latter of which, though insoluble in water, is readily soluble in a hot strong brine. From the solution thus obtained, metallic iron throws down the copper in a metallic state, regenerating the protochloride of iron; which is then ready for the treatment of a fresh portion of oxidized copper ore. In the case of slimy ores, the contact of the bath with the ore is effected by agitation in tubs; but when the ores are granular, lixiviation in large vats is equally efficient and simpler. The hot solutions, charged with chlorides of copper, are digested in tanks with scrap-iron, or better, are made to flow through covered channels containing the scrap-iron, and in their passage lose the whole of their copper; the reaction at the same time evolving so much heat as to keep up the temperature of the liquid. In order to prevent a certain loss of chlorine, which otherwise takes place from the production of some basic ferric chloride in the reaction between the ferrous chloride and the oxides of copper (both protoxide and dinoxide being generally present in calcined ores), a portion of sulphurous fumes from the roasting is made to pass through the regenerated bath before adding it to fresh ore. This has hitherto been effected by injection, with the aid of a jet of steam.

By F. Keller

ALUMINUM alloys containing magnesium and silicon are susceptible to strengthening and hardening by suitable heat-treatments, and they constitute a class of alloys of considerable commercial importance. Generally, they contain these two elements in the proportions required for the formation of the intermetallic compound Mg2Si, or an excess of silicon; no commercial wrought alloys are made with an appreciable excess of magnesium. The reason for not having excess magnesium is obvious from the results given in this paper, since it is shown that excess magnesium results in a proportional decrease in the solubility of Mg2Si. This is the eighteenth1 of a series of papers from the Aluminum Research Laboratories dealing with the equilibrium relations in aluminum-alloy systems; most of the previous publications concerned binary aluminum-alloy systems; this is the fourth of a group pertaining to ternary aluminum-alloy systems. The work on this system was com-pleted in 1930, but the results were not published because of the pressure of other work. Hanson and Gaylor2, in 1921, presented the results of an extensive investigation of the aluminum-magnesium-silicon system. Their results indicated that an excess of magnesium over the amount required to form the compound Mg2Si caused a noticeable decrease in the solid solubility of Mg2Si in aluminum. A more recent investigation3 in these laboratories showed that the solid solubility of Mg2Si in aluminum was 1.85 per cent at 595° C. and decreased to 0.30 per cent at 300° C. The results of the latter investigation were used as the basis for the present work.

Jan 1, 1936

By C. H. Noren

For some years the Du Pont Company has utilized computer calculations to study the various theoretical properties of explosives. These studies have yielded valuable information on the effects of density changes or formulation changes on detonation rate, detonation pressure, explosion pressure, heat of explosion and numerous other properties, and have aided in evaluating the theoretical potential of explosives. In addition, a multitude of laboratory tests have been utilized for the evaluation of explosives. When comparing the computer data and the voluminous test data it became evident that numerous anomalies existed. Tests in rock were required to study explosives under borehole confinement. This fact was further emphasized after numerous field measurements showed that the borehole velocity of commercial explosives did not match the theoretical value but was dependent on conditions of field use. Since we are interested in the practical aspects of blasting, a program was initiated to evaluate explosives as used in commercial blasting. INSTRUMENTATION Most of you are familiar with the extensive work that has been done by the U. S. Bureau of Mines in their studies of strain measurements in rock. Early in our work we adopted procedures similar to those used by the Bureau of Mines. Strain pulses were measured by gages cemented in boreholes. Since we were primarily interested in the effect of explosives in the zone where fracture might occur, this system offered several disadvantages for Du Pont: 1. Cemented gages were expensive and not reusable. 2. When gage holes were used for several shots, there was considerable question as to the condition of the rock after the first shot.

Jan 1, 1968

By M. G. Magnuson, H. O. Hofman

When dry chlorine gas is made to act in the cold upon fiuely-divided gold,' it converts the latter with evolution of heat into auro-auric chloride, Au4 Cl4, a hard, dark-red, hygroscopic salt. Moisture splits this salt into aurous and auric chloride, Au²C14 = AuCl + AuCl³; treatment with water converts it into auric chloride and gold, 3 Au²CI4 = 4 AuC1³ + Au². Aurous chloride, when stirred with water, undergoes a similar decomposition, 3 AuCl = AuCI, + Au,. These decompositions of auro-auric chloride and of aurons chloride furnish the explanation for the practice of moistening an ore before it is treated by the Plattner chlorination-process; practical experience having shown that gaseous chlorine gave an unsatisfactory extraction with dry ore. According to Rose12 fine gold is acted upon more slowly by chlorine than gold containing some base metal, e.g., copper. He also says that small quantities of silver increase the rate of solution, but adds that the coating of silver chloride formed, checks, and finally stops, further action, if the percentage of Silver be increased beyond a certain undetermined amount. Bromine3 acts upon finely-divided gold in a manuer similar to chlorine; the auro-auric bromide, Au²,Br4,, however, is not hygroscopic. Upon treatment with water it is decomposed as is the corresponding chlorine salt. It is generally believed that bromine does not act as energetically upon gold as does chlorine. This seems to be borne out by the results in the leach- +1MASSACHUSETTS INSTITUTE OF TECHNOLOGY, BOSTON, MASS.

Jan 1, 1905

By Leonard P. Skolnick

PROPERTIES of materials containing a hard con-stituent dispersed in a metallic matrix are dependent on the distribution of the hard phase.'-' The grain growth of titanium carbide in liquid nickel was studied in order to understand microstructural development in this and similar systems. Smith" has examined the influence of surface energy on the distribution of phases in alloys. The grain growth of tungsten carbide in cobalt has been the subject of many conflicting theories. Those prior to 1950 have been summarized by Goetzel.' Recently, Gurland and Norton3 and Gurland8 have indicated that growth occurs primarily by diffusion through the liquid phase in order to lower the inter-facial energy between the carbide and the liquid metal. In the development of the Ti-C-Ni ternary phase diagram, Stover and Wulff9 have shown that both eutectiferous dendritic titanium carbide, and primary titanium carbide which had developed crystals of cubic symmetry, were rounded by heating below the solidus, and that if primary carbide was already present the typical eutectic decomposition products were not formed. Experimental Procedure The infiltration technique was used to study the grain growth of titanium carbide in nickel. In contrast to sintering, infiltration more readily assures uniform dispersion of the two phases, and the problems associated with mixing by milling; i.e., mill contamination, breakdown of original carbide size in the operation, development of interfering surface films, etc., are avoided. In addition, the complicating effect of densification by shrinkage is eliminated. The titanium carbides used were commercial grades. Their chemical analyses, size distributions and shapes are summarized in Table I. Size analysis was conducted by microscopic count on a minimum

Jan 1, 1958

By Frederick Laist

IT IS obviously impossible to design a copper smelting plant which could be considered, ideal under all conditions. For example, a plant properly designed to smelt the concentrates resulting from the treatment of porphyry ores by flotation would not be the kind of plant that one would design for the treatment of a coarse pyritous copper ore. The smelting of flotation or other fine concentrates is generally accomplished in a reverberatory plant, although occasionally the concentrates are sintered and then smelted in blast furnaces. On the other hand, coarse self-fluxing ores, whether pyritic or semi-pyritic, are generally smelted in a blast-furnace plant. Even this statement is only- approximately true, since the choice will be influenced by many factors; for example, the kind of fuel available (coal, oil or coke), the value of power (electric or steam), the uses to which waste steam may be put (heating, drying, etc.), the cost of refractories (silica and fire brick), the permanence and continuity of the ore supply and the relative first costs of the two types of plant (the reverberatory plant is generally more expensive to construct and to shut down), the contour of the site on which the plant is to be built (rugged, rolling or flat), the intelligence and character of the labor avail-able, and many other factors. From these remarks, it is evident that no copper smelter can be ideal for all conditions of ore and locality, and inasmuch as most of the copper now being pro-duced comes from fine or flotation concentrates and these are generally smelted in reverberatory furnaces, I shall confine my remarks to this type of smelt-ing plant.

Jan 5, 1923

By G. Bloomsburg, R. E. Williams, S. D. Vincent

A modeling scheme is developed to simulate the hydrogeologic effects of mine design and development in unsaturated rock. Simulations are conducted using the UNSAT2 finite element computer program and hydrogeologic data from the site of a proposed mined-out waste repository at Yucca Mountain, NV. Results of the simulations are analyzed for: •variations in the direction of ground water flow and in the distribution of pressure head caused by the design of the mined out openings; and •mine design variables that affect the predicted rates of mine water inflow. Evaluating the hydrogeologic impacts of mine design and mine development in unsaturated rock is significant in several respects. Characterization of the preemplacement of wastes along the fastest path ground water flow system at the Yucca Mountain site has been a primary research effort. Ultimately, however, the degree to which waste isolation is achieved will depend largely on the post-mining hydrogeologic environment as altered by the mine design and on the radionuclide inventory and resulting heat effects of the repository. Therefore, an ongoing characterization of the proposed mined-out nuclear waste repository at Yucca Mountain, NV, is recommended. Modeling results indicate that: •mined out openings will affect the movement of ground water, both in rate and direction; •hydraulic effects of mine development depend on the hydrogeologic environment and on mine design geometry; •mine water inflow is possible in the unsaturated zone, even for mines developed in hydrogeologically homogeneous rocks; and •mine water inflow can occur at values of down ward flux that are appreciably less than the saturated hydraulic conductivity of the overlying rocks.

Jan 1, 1991

By Walter Harvey Weed

The enrichment of mineral-veins as a result of the migration of material from an upper oxidized or disintegrated part of a vein to a lower level, where it is redeposited, is now, I believe, quite generally accepted as one explanation of the occurrence of bonanzas in gold- and silver-veins, as well as that of bodies of high-grade ores in cupriferous deposits.* Vogt has called attention† to the fact that there are numerous examples of such rich shoots which are " of exclusively primary character, and dependent upon the laws which governed the original ore-deposition." To this I would add that there are also other examples which are neither of primary origin nor due to descending waters, but. result from a reopening of the veins and their penetration by ascending heated waters whose metallic contents are deposited by reaction with the primary pyrite (and possibly other minerals), forming "secondary" enrichments. My studies of the copper-veins of Butte, Montana, show: That the veins there are of several ages and systems; that the older primary quartz-pyrite veins were reopened by later movements, correlated with a period of volcanic activity; and that they were penetrated by hot alkaline waters carrying copper and arsenic in solution, which was deposited presumably by reaction with the pyrite of the original vein. The enormous development of the Butte deposits, attendant upon the extraction of nearly 10,000 tons of ore a day, has revealed many facts concerning the nature and distribution of the ores. Enargite, the copper sulpharsenate, formerly a relatively rare mineral, is now found to be the chief ore of some veins,

Jan 1, 1903

By G. R. Speich

RECENT studies by Smith and Olney,1,2 Olney,3 Greifer and Salli,4 Rys etal., and Olney and smith 6 have established that graphite is the first decomposition product to format the surface of hypereutectoid plain-carbon steels when they are austenitized in a vacuum or inert atmosphere and slowly cooled. This graphite evidently forms directly from the austenite and only at the surface of the specimen. The interior of the specimen is found to be free of graphite. The graphite layer can almost completely cover the specimen surface and the rate of its formation is markedly sensitive to the orientation of the austenite. The present work was undertaken to study this phenomenon further, especially with regard to the effect of temperature and austenite orientation. The material studied in this work was a high-purity iron-carbon alloy containing 0.88 pct C, 0.005 pct Mn, 0.016 pct Si, 0.005 pct S, and 0.002 pct P. Specimens were heat-treated in a commercial hot stage modified for rapid quenching.7 This permitted direct observation of the formation of the surface graphite. A vacuum of 10"" to 10-5 mm of Hg prevented oxidation or decarburization of the specimens. Specimens were austenitized for 30 min at 1100°C and quenched to a series of lower temperatures where they were isothermally transformed. Surface graphite was observed to form at 700°, 750°, and 780°C but not at 825°, 900° or 1000°C. Since the maximum solubility of austenite for graphite is 0.88 pct C at 800°C,8 surface graphite only forms at tem-

Jan 1, 1962

By Frank Foote, V. H. Nordstrom, Eric R. Jette, Bernard Queneau

The nickel-chromium alloys form the base for many industrial heating alloys, so that this system is of considerable practical importance. The literature on these alloys, however, contains much conflicting evidence, not only regarding the solubility limits of the terminal solid solutions at different temperatures but even regarding the number of phases existing in the system. Part of the difficulty undoubtedly arises from the fact that chromium of sufficiently high purity has been available only during the last few years. A second and possibly even more important difficulty arises from the ease with which chromium reacts with silicon and carbon compounds and the atmosphere to form silicides, carbides, nitrides and oxides. Pilling and Kihlgrenl in 1929 reviewed the existing scanty information. They did not consider the diagram by which they summarized the various bits of information to be entirely satisfactory. Matsunaga2 investigated the system by thermal analysis, microscopic examination and other means. Electrolytic nickel of 99.9 per cent purity and thermit chromium containing 0.30 per cent Al, 0.40 per cent Fe, 0.25 per cent Si and 0.04 per cent C were used. A Tammann furnace with hydrogen flowing through it was used for melting. Sekito and Matsunaga3 reported an X-ray investigation, presumably on these same alloys, which, as far as can be judged from the abstract, essentially confirmed the thermal and microscopic results. Nishigori and Hamasumi4 found compositions for the terminal solid solutions in equilibrium at the eutectic temperature which agreed fairly

Jan 1, 1934

By C. W. Davis, R. S. Dean

AMONG naturally occurring inorganic compounds, magnetite has many unusual and interesting properties, and it is the purpose of this paper to call attention to these properties and review possible uses of magnetite that might be based on them; in other words, to see what uses may be found for magnetite as a physical rather than as a chemical entity, as a mineral rather than as an iron ore. The Mineral Physics Studies initiated in the Metallurgical Division of the U. S. Bureau of Mines a few years ago gathered together much information on mineral properties, and they are therefore the principal source of material for this paper. Magnetic Properties Of Magnetite And Possible Uses As A Magnetic Material Magnetite is unique among minerals for its great magnetic susceptibility, approximately one-third that of soft iron, and some magnetites are permanent magnets, or lodestones. The literature contains many measurements of magnetic properties of individual magnetite crystals, but no systematic survey of the effect of mechanical preparation and heat-treatment was available until the recent investigations of the Bureau of which included not only susceptibility but coercive force and remanence as well. For the purpose of orientation, Table 1 gives the magnetic properties of several samples of magnetite and of a few other substances3. This table indicates that when ordinary magnetite is powdered it decreases in susceptibility and increases in coercive force and remanence, approaching the properties of lodestone. The properties of lodestone are in fact probably due to the development of very large internal surface on fine grain size4.

Jan 1, 1937

By Leonard J. Prosser, Joseph Cervik, John H. Perry

The Bureau of Mines has developed several techniques for draining methane from coalbeds in advance of mining. Drilling long horizontal holes from an underground location is one such technique, which was successfully demonstrated in the Pittsburgh and Sunnyside Coalbeds. The same technique has now been applied in the Mary Lee Coalbed at Jim Walter Resources, Inc. 's No. 4 Mine, Brookwood, Ala. , where two holes were drilled horizontally--one to a depth of 1,010 feet (308 m) and the other to 540 feet (165 m). The 1,010-foot (3083) hole proved successful in degasifying a portion of the Mary Lee Coalbed. The hole drained methane for 1 year, during which time the initial gas flow of 200,000 ft3/d (5,663 m3/d) declined to 65,000 ft3/d (1,840 m3/d). Total gas production was 40 x lo6 ft3 (1.1 x lo6 m3 ). The gas was of commercial quality, with 98 pct methane and a heat rating of 990 Btu/ft (36.89 Mj/m3). The methane emissions from the faces of the mine section advancing into the degasified zone were reduced by 60 pct. The 540-foot (165-m) hole was terminated prematurely when it became impossible to maintain an open hole. Because of caving, very little gas was drained through this hole.

Jan 1, 1982

By Y. Oinouye, H. Ries

Of the several interesting physical properties of clay which have claimed the attention of investigators in recent years, none is more important than the behavior of the material when heated to temperatures above those of dehydration. Some of the problems to be solved are: 1. The mineralogical changes that take place in firing. 2. The relation between temperature and change in constitution, shrinkage, porosity, etc. 3. The importance of the time factor, as duration of firing, either in reaching a given temperature, or of exposure to a constant temperature. Mineralogical Changes As a result of fusion, reactions take place between the constituents of a clay, which result in a reorganization of the mass, and the formation of new compounds. Of the new minerals developed, sillimanite is the one usually recorded, and has been referred to by a number of observers.' There appears to be a difference of opinion, however, regarding the temperature at which it is formed. Thus Klein2 notes that sillimanite forms only above 1300" C., while Mellor claims that it can develop below 1200" C., the difference in results being conditioned by the time factor. In Klein's experiments the test pieces were fired in 12 hr., while in Mel-lor's, the temperature rose from 800" to 1180" in 24 hr., and occupied the same time in cooling back to 800".

Jan 1, 1918

By F. J. Norton

THE object of this investigation was to make a comprehensive study of the degassing of molybdenum in order to determine how rigorous a treatment was necessary to completely remove sorbed gases from molybdenum electrodes in vacuum tubes. Some work has also been done with tungsten, nickel and carbon. As a logical development of this work it has been shown that the gas is present throughout the body of the metal and a study has been made of the solubility of nitrogen in molybdenum and tungsten and the rate of diffusion of nitrogen through molybdenum has been calculated. Tests were made on molybdenum from all the commercial sources and no difference was discovered in the nature of the gases present, the amounts or the ease of removal. The reason for this was apparent when a study was made of the manner in which gases are absorbed by gas-free molybdenum. It is necessary to heat molybdenum to 1760° C. in a vacuum of the order of 0.001 micron for a time which varies lineally with the thickness, in order to obtain a condition in which no further gas is evolved by the sample. A sample so degassed can be handled and subsequently assembled in a tube and then degassed readily. The gases obtained from molybdenum are carbon monoxide and nitrogen, the nitrogen being the more difficult to remove.

Jan 1, 1932

A construction material based on plasticized sulfur and mineral aggregate, that is superior in corrosion resistance and strength to portland cement concrete. The material can be used in the chemical, metallurgical, and fertilizer industries, and will also provide an attractive market for by-product sulfur resulting from compliance with pollution regulations. How It Is Made Sulfur concrete is thermoplastic material. Plasticized sulfur is mixed with sand and gravel aggregate heated to 375-400° F. The sulfur melts and acts as the binder or cement. The sulfur concrete is poured hot and sets at a temperature of 200° F. Full strength is attained in a few hours, compared to several days for portland cement concretes. Sulfur concrete even pours and sets in freezing weather. Although unmodified sulfur with aggregate will produce a sulfur concrete with good initial properties, it undergoes crystallographic modifications, and deteriorates with time, particularly when exposed to moisture or freeze-thaw conditions. The Bureau of Mines has developed plasticizers which, when reacted with the sulfur, give sulfur concretes with excellent moisture and freeze-thaw resistance. The plasticizers are based on mixtures of dicyclopentadlene (DCPD) and ollgomers of cyclopentadiene. About 5 percent by weight of the plasticizers is reacted with molten sui fur for several hours. The sulfur cement can be used directly or allowed to solidify for easier handling and storage.

Jan 1, 1981

By H. Asgari, A. G. Odeshi, J. A. Szpunar

In the current research, the role of grain size on the texture formation and mechanical behavior of rolled AZ31B Mg alloy is investigated under shock loading conditions. The grain size of the original asrolled sample was 8 µm and different grain sizes, e.g. 25 and 46 µm, were produced by heat treatments at temperatures in the range of 400-500 °C. In order to evaluate the effect of grain size on the anisotropy of mechanical behavior, the samples were cut along the rolling direction (RD), transverse direction (TD) and normal direction (ND) and tested at strain rates of 900 and 1200 s-1 using Split Hopkinson Pressure Bar. Texture measurements showed that initial texture of the samples cut from the as-rolled sheet is a weak rtype texture. However, a stronger texture was observed for samples with large grains. After shock loading, a (00.2) basal texture developed in all samples and the intensity of the basal poles was higher in samples with coarser grains. This observation is corroborated by high twinning activity and possible activation of pyramidal <c+a> slip in coarse grained samples. Besides, the strength of basal texture increased with increase in the strain rate. Furthermore, the samples with larger grain size showed lower strength and higher ductility, and this was observed for all investigated strain rates.

Jan 1, 2014

By William C. Buell

As used in connection with open-hearth or other high-temperature operations, "insulation" refers to a multitude of substances, natural or manufactured, that have the one principal property of preventing the flow of heat by conduction to a greater degree than refractories can prevent it, the principal properties of the latter being resistance to temperature and/or chemical action. The term "control" as commonly applied to the mechanization of management functions is inappropriate without qualification, for without some degree of control of every operation we could produce no steel worthy of the name. Although grouped together in this paper, insulation and control in open-hearth furnaces have little, if any, interrelationship, therefore the paper is made up of two distinct parts. INSULATION OF OPEN-HEARTH FURNACES More than ten years ago the writer proposed the insulation of an acid open-hearth furnace system below the charging floor, and it was accomplished, with gratifying results. Possibly that was the first time the insulation of regenerators and slag pockets of any open-hearth furnace was undertaken, but shortly thereafter such insulation became general, and when the six groups of 150-ton furnaces1 were built in 1929-1930, they were completely insulated below the charging floor. While the practice was accepted at least five years ago, it was not well understood, however, as indicated by the following incident which occurred in connection with an installation made in 1929. After the

Jan 1, 1935

By Bruce W. Gonser, Robert J. Nekervis

EACH metal has a unique combination of properties that distinguishes it from other metal;. Su& a combination may account for applications that cannot be met very well by anything else. This is particularly true of tin, one of the earliest metals used by man. Table i shows the consumption of tin in the United States by usage for the years 1949 and 1950, which may be considered to be generally typical of current usage. The major applications-tinplate, solders, bronze, and babbitt-were well established a century ago. Applications for the metal and (probably later) of tin alloys started more than 5000 years ago. Fortunately for the ancients, tin is one of the metals whose oxide is easily reduced by carbon. Nature further simplified the refining problem by providing only one ore of commercial importance, cassiterite (SnO2). Tin is easily reduced from cassiterite. All that is necessary is high heat in the presence of carbon. It is quite possible that back in the dawn of history, tin was discovered when black alluvial sand was thrown on a fire, either to bank it or to put it out. SOURCES OF TIN All the important tin-producing centers are in the southern hemisphere, far away from the&apos; industrial consuming centers. Fig 1 shows their location and 1950 production. Reserves are adequate, and the industry is able to produce considerably more tin than is

Jan 1, 1953

By William C. Buell

As used in connection with open-hearth or other high-temperature operations, "insulation" refers to a multitude of substances, natural or manufactured, that have the one principal property of preventing the flow of heat by conduction to a greater degree than refractories can prevent it, the principal properties of the latter being resistance to temperature and/or chemical action. The term "control" as commonly applied to the mechanization of management functions is inappropriate without qualification, for without some degree of control of every operation we could produce no steel worthy of the name. Although grouped together in this paper, insulation and control in open-hearth furnaces have little, if any, interrelationship, therefore the paper is made up of two distinct parts. INSULATION OF OPEN-HEARTH FURNACES More than ten years ago the writer proposed the insulation of an acid open-hearth furnace system below the charging floor, and it was accomplished, with gratifying results. Possibly that was the first time the insulation of regenerators and slag pockets of any open-hearth furnace was undertaken, but shortly thereafter such insulation became general, and when the six groups of 150-ton furnaces1 were built in 1929-1930, they were completely insulated below the charging floor. While the practice was accepted at least five years ago, it was not well understood, however, as indicated by the following incident which occurred in connection with an installation made in 1929. After the

Jan 1, 1935