Search Documents

By Eugene T. Sheridan

This report presents data on individual plants of the fuel-briquet and packaged-fuel industries that were circularized by the Bureau of Mines, United States Department of the Interior, in its annual survey for 1958. Only plants that processed fuels of mineral origin were included; specifically, plants that manufactured briquets from charcoal were excluded. Fuel briquets and packaged fuel are manufactured by mixing fine-sized fuels with binders and compressing into small individual shapes. Both are used mainly for residential heating in the United States, but they differ considerably in appearance and physical characteristics. Briquets usually are produced as small, pillow-shaped forms, 2 to 4 inches in length, weighing from 2 to 4 ounces. Pack-aged fuel consists of 3-to 4-inch cubes, 6 or 8 of which are wrapped in heavy kraft paper to form a package weighing 10 to 15 pounds. Briquets are made with a water-insoluble binder and are designed for rough handling and outdoor storage, whereas packaged fuel generally is made with a water-soluble binder and must be stored indoors to prevent deterioration. Briquet plants are relatively large and usually are at mines or in dock areas where large quantities of fine-sized fuels accumulate. Packaged-fuel plants are smaller and are used chiefly by retail dealers to convert locally available coal and coke fines into a product that can be burned efficiently in residential beating equipment.

Jan 1, 1959

By H. G. Iverson

An investigation was conducted on the conditions affecting the precipitation of aluminum by autoclaving synthetic solutions containing Na2SO4, Al2(SO4)3, H2SO4, and H2O. Virtually all of the alumina could be precipitated as natroalunite (NaAl3(SO4)2 (OH)6). This product could be readily filtered and dried. Results are reported in terms of alumina precipitated in this compound and not in terms of alumina itself. Solutions of ~ 0.30, ~ 0.60, and ~ 0.80 mole/liter A1203 and various concentrations of H2SO4 and Na2S04 were investigated. The optimum time and temperature for autoclaving were 20 to 30 minutes at 200° C. The highest yields of natroalunite were obtained from solutions containing little H2SO4 and ~ 2 moles Na2SO4 per mole A1202. Acid in quantities of 0.3 to 0.5 mole/mole of alumina in solution depressed the yield to 90 percent or less. In differential thermal analysis, at 1,000° C the natroalunite precipitate decomposed without melting to yield SO, and SO2 gases, a solid composed of Na2SO4, and gamma and alpha Al203. Continued heating to 1,200° C produced No SO, and alpha A1303. Water-leaching of this product removed the Na2S04 and left a final residue of alpha A1203.

Jan 1, 1968

By George J. Young

DURing the spring of 1910 1 visited a number of open-pit brown-coal mines and underground workings in the vicinity of Halle, Halberstadt, Leipsic, Cologne and Bonn. The notes which I took and the observations which I made at the time have been condensed and make up the principal part of this paper. Certain supplementary information has been taken from several sources which are given in the paper. The mining of brown coal is one of the important industries of Germany. The coal varies in color from dark brown to almost black and is soft like loam. Pieces of wood and strips of bark and even parts of tree trunks are frequently encountered in the excavation although the coal for the most part consists of a pulverulent, more or less matted mass of small particles of vegetal matter. It is a product between peat and lignitic coal. An analysis, taken from Coal Resources of the World shows the approximate composition of the material: Moisture, 53.73 per cent.; ash, 4.98; fixed carbon, 18.08; volatile carbon, 23.31 per cent. Thc principal characteristic is the amount of moisture. This seldom runs less than 48 per cent. The ash is usually low and ranges from 5 to 10 per cent. The sulphur content is usually less than 0.5 per cent. The heating effect of the fuel ranges from 2,000 to 2,500 calories. The commercial deposits are confined to the Tertiary period although

Jan 1, 1916

By T. H. Brien, O&apos

At nearly all of the copper smelters in the Southwest, at some time, calculations have been made having in view the economy of replacing fuel oil with pulverized coal as a heat-producing medium for smelting operations This matter has been, and is more so now than at any time heretofore, of very great importance. Due to the intensive development of oil-producing areas of the world and the tremendous use of fuel oil for many purposes, it seems that before many years the supply of oil will become so small as to prohibit its use for such operations as smelting. This may be caused by prohibitive prices, or even by government decree as a conservation measure. In the event that the use of fuel oil becomes out of the question, the copper companies have just two alternatives: the use of pulverized coal or electricity. The copper companies of the Southwest produced an average of 808,400,000 pounds of copper per year for the war years of 1916, 1917 and 1918. This figure is, of course, a higher one than has prevailed since the war, but at the present time nearly all of the mines and smelters are getting back to capacity. There is no doubt whatever that the consumption of copper is going to increase, perhaps for the next ten years. This means that more copper mines will be discovered and developed, and that the mines which are now producing will be called upon for a greater production. This all tends to show that the mine manager who is looking ahead must develop some substitute for fuel oil in the event of its use becoming prohibitive, and all indications seem to point in that direction. The only coal which is commercially available to the smelters in the district under discussion must come from Colorado and New Mexico. These coals are high in ash and volatile matter and comparatively low in calorific value. The proximity of the smelter to the coal mines is a large factor in determining which fuel is more economical. Most of the smelters within two or three hundred miles of the coal mines find it more profitable to burn coal, while those at greater distance find that the higher freight charges on the coal make the use of oil more economical.

Jan 1, 1923

By H. E. Howe, A. A. Smith

The creep properties of lead alloys have been studied by a number of investigators but most of the work has been done on extruded material and the amount of data available on rolled alloys is surprisingly limited. Greenwood1 and his collaborators investigated various rolled commercial leads containing relatively small amounts of impurities, Phillips2 likewise studied rolled commercial leads, although he did include a few alloys— such as tellurium lead and one per cent antimonial lead. But as far as the authors are aware no data on the creep properties of so-called "hard leads"-—i.e., containing from 4 to 8 per cent antimony—have been published. In this paper some data are presented on a few antimonial lead alloys and compared with a copper-bearing lead. Preparation OF Specimens All the alloys used in this investigation were cast at a temperature of 400°C. into an open cast-iron mold preheated to Ioo°C., the resultant casting being % by I by 10 in. The copper-bearing alloy was cold-rolled by 10 per cent passes to a thickness of 0.100 in. Creep specimens 16 in. long were prepared by clamping the strips between wooden blocks and machining the edges of the strips parallel by means of a plane. Careful manipulation gave parallel specimens with no reduced section and with a minimum of distortion. The antimonial lead castings were hot-rolled in 10 per cent passes at a temperature of I50°C. to a thickness of 0.400 in., the heating being carried out in an electric oven after each pass through the rolls. After the castings had been broken down to 0.400 in., they were allowed to cool to room temperature and then cold-rolled to 0.100 in. with the usual Io per cent passes. Sufficient time was allowed after each pass for the strips to cool to room temperature. The apparatus and method of measuring strain have been adequately described in a previous paper3 and essentially the same practice was used in obtaining the present data. Time-extension curves for only two alloys are given, since these are typical of all. Figs. I and 2 show the time-extension Curves for the copper-bearing alloy A at 30°C. and loo°C., and Figs. 3 and 4 show

Jan 1, 1945

By M. Carvalho

The primary motivation underlying the proposal of polygeneration systems for mine sites is to increase the efficient use of natural resources by combining different technologies and energy resources while satisfying energy service demands. For many mineral producers, particularly in Canada?s mining extremes of climate and depth, energy in support of mineral production can be the second largest cost centre after labour. A generic methodology is proposed for the design of energy supply systems in mine sites, based on a search for the minimum discounted cost of energy supplied for all feasible different plant configurations. These configurations can be represented within a connectivity matrix which corresponds to a network representation. A Mixed Integer Programming formulation is set out for the multiperiod synthesis and operational planning problem. This is characterized by i) binary variables for the selection of technologies, ii) integer variables for the determination of the number of units installed, and iii) by continuous variables for the representation of energy and economic flows. Through the integration of particular energy supply strategies matching specific mine circumstances (on-grid, remote, degree days, etc) and consideration of technologies that improve energy efficiency, hitherto not considered new technologies and demand management systems or new perspectives on optimal mine site energy supply can be investigated. Some of these investigations identify the economic conditions through which biomass energy feedstocks should be used, for direct heat production, for gasification and providing for Fischer-Tropsch syndiesel manufacture. As well as integrating demand from mobile diesel-fuelled plant into an optimization procedure that hitherto has only been considered for static energy production and consumption plant, this analysis shows how the techniques can be used to explore economic conditions of threshold prices for biomass (purpose-grown biomass and peat are considered herein) and trucked-in diesel. The methodology also allows for electricity and syngas storage and diesel and biomass bunkering. Within the paper the energy demands for a remote, open pit mining operation located in Northern Ontario are considered as a case study to illustrate the technique and investigations. As expected, for mines close to electricity, natural gas, and diesel distribution infrastructures, the optimal choice is to connect. When a constraint is applied specifying that connection is not possible, as would be for the case exemplified, the optimal choice includes some of the more exotic options for mine site energy supply.

Aug 1, 2013

By Charles Himrod

IN presenting this paper it is not intended to enter into any discussion of the theory of the blast-furnace, but simply to give the results of a number of determinations of CO and CO2 in furnace gases, and some conclusions arrived at, and the result of an experiment made in hopes of increasing the production of CO2. In the first table, on page 198, is given the averages of a number of analyses of gases of different furnaces, and in the second, of two stacks of different sizes under varying circumstances. The conclusions arrived at as to what influences the production of CO2 are as follows: 1st. Kind of fuel. Bituminous coal not permitting the formation of as much CO2 as coke. 2d. Kind of ores. Rolling-mill cinder being much less favorable to formation of CO2 than hematite ores, magnetites probably less than hematites, but more than cinder. 3d. Length of time of contact of gases with ore. Small furnaces and too rapid driving both waste fuel by not allowing enough time for conversion of CO into CO2. 4th. The temperature of blast. The hotter the greater the quantity of CO2. 5th. Regularity of passage of stock through the furnace. The hanging and dropping of the stock, however slight, seems to pack it more solidly in the hearth, increases the resistance to the blast, and decreases the quantity of CO,. These are the most common causes noticed which influence the production of CO2, unless we except the one that might be considered the greatest of all, the one that has spoiled so many tons of iron, and the amiability of so many furnacemen, the one most dreaded, the great unknown. It would seem a self-evident proposition that the better the contact of the gases with the ore and the less with the fuel, the greater would be the amount of CO2 produced. To prolong the contact of gas with the ore furnaces are enlarged with advantage, and pains are taken to charge the stock in such a, manner as will best promote it. Still, with furnaces of most approved construction and most skilful manipulation, the gases leave the furnace so rich in CO, that not half the heating power of the fuel is obtained, and the highest

Jan 1, 1877

By S. O. Choi, H. -S. Shin, W. -K. Song

Nuclear waste should be disposed with the best warranty for the national health and welfare. Among the several repository systems, the deep underground disposal is considered to be a most suitable system in Korean peninsula. However it demands basically the comprehensive stability analysis such as the behaviour of discontinuities in rock mass, the behaviour of ground water, and the reaction of rock stress according to the heat from the nuclear waste. For these purposes, the underground nuclear waste disposal repository was simulated in two- and three- dimensions. It shows that emphasis will be given to the thermal conductivity of discontinuities and the thermal convection of ground water as well as the thermal stress generated by the nuclear waste for design and construction of repository system, and they should be obtained from the field measurements. Déchets nucléaires devront tre déposés avec la meilleure garantie pour la santé et le bien public. Parmi les plusieurs systèmes de dépôt, la disposition en souterrin profond est considérée au système le plus approprié en Corée. Pourtant ce système demande essentiellement l’analyse éten-due de stabilité comme le comportement des discontinues en masse rocheuse, le comportement de l’eau souterrin et la réaction des contraintes de roche selon la chaleur depuis les déchets nucléaires. Pour ce but, le dépôt des déchets nucléaires en sous-sol a étè simulé en deux et trois dimensions. Il montre que l’accent sera donné à la conductivité thermale des discontinues et la convection thermale de l’eau souterrin aussi bien que la contrainte thermale générée par les déchets nucléaires pour le plan et la construction du systèmes de dépôt, et ils devront tre obtenus depuis les mesures sur place. Die Kernwüste muß mit der besten Gewähr für die nationale Gesundheit und die Wohlfahrt angeordnenet werden. Unter einigem Fundgrubesystem, das tief unterirdisch Wegwerfen werde in Betracht das passendest System in der koreanisch Halbinsel gezogen. Jedoch, es verlangt grundzätzlich die umfassend Stabilitätsberechnung so wie das Behnehmen mangelnder Konti-nuität in der Felsmasse, das Behnehmen des Grundwasser, und die Reaktion der Felsenbelastung nach der Hitze von der Kernwüste. Für diesen Zwecke, die unterirdische Wegferfenfundgrube der Kernwüste wurde in der zwei und drei Dimensionen gesimuliert. Es beweist daß die Betonung wird zur thermisch Leitfähigkeit mangelnder Kontinuität und thermisch Konvektion des Grund-wasser sowie die thermisch Belastung ergezeugt durch die Kernwüste für den Entwurf und die Konstruktion des Fundgrubesystem gegeben werden, und sie müssen von den Feldmaße ergelangt werden .

Jan 1, 2003

By W. H. Smith

IN the course of an investigation on chromium containing minor amounts of alloying elements, the information herein has been obtained on the crys-tallographic orientations resulting from arc melting, rolling, and annealing. The chromium used in this investigation was electrolytic flake obtained from the Electro Metallurgical Co. This material was heated for 20 hr at 1600°C in hydrogen with a dew point of about — 100°C. The oxygen and nitrogen content of the chromium after this treatment was 0.0003 pct 0 and 0.005 pct N. Five pounds of this chromium were arc melted in a water-cooled copper crucible. After arc melting, the oxygen and nitrogen contents were 0.002 and 0.025 pet, respectively. A section of this ingot is shown in Fig. 1. By means of a back-reflection Laue technique, the crystal habit of the cast ingot was determined. As expected, it was found that the [loo] was approximately the axis of the columnar grains. In this respect, chromium behaves like other body-centered-cubic metals in that a cubic axis is normal to the cold surface of the mold. A slab cut from this ingot was rolled at 600°C as follows: four 30 pct reductions were made with intermediate anneals at 1200°C for 15 min. Rolling was done with the [loo] of the columnar grains in the rolling direction. Following the final anneal, an 80 pct reduction was taken at 600 °C. The final sheet thickness was ten mils. By polishing and etching, the thickness was reduced to four mils and the grain orientation determined by the transmission Laue method using molybdenum radiation with a zirconium filter. Fig. 2 is the (110) pole figure for this material with the ideal (100) [011] and (111) [112] orientations indicated. The orientation is typical of most cold rolled body-centered-cubic metals having the [llO] of the grains approximately in the rolling direction and the (100) planes approximately in the plane of the rolled sheet. There is also evidence of some 10) [1 orientation. The grain orientation of sheet rolled 40 and 80 pct in the same direction as before at 600°C followed by recrystallization at 12000 C for 15 min was determined by a back-reflection Laue technique. A random texture was found in both cases. This 1200°C 15 min anneal was found to give complete recrystallization and some grain growth.

Jan 1, 1956

I HAVE previously demonstrated to you as well as I knew how in what way ores are treated and then how the separated metals are brought to their pure and ultimate limit of perfection by means of smelting and other artificial fires; all except gold, which remained incorporated in the silver. Because the method used for the others does not serve for this, and if indeed it did serve it would be a great labor and could not be done without a great loss of the thing, it is therefore necessary to proceed with the practice of another art if you wish finally to extract gold from the bonds of the intrinsic substance of silver, for it exists bound and scattered in this like the soul in the body of living creatures. In this, unlike the other works where you make direct use of the vigor of the fire, you use a substance that is like water, drawn by the force of fire from a very powerful composition of two materials. This is a very marvelous thing to consider as a liquor because of its powerful effects. It is made by artificial distillations and it has an acid property and the power of corroding and reducing into itself silver and any other metal placed in it, with the exception of gold. Nothing is apparent in it except a pure water. It is indeed a very ingenious thing for which we must be greatly indebted to that philosopher, alchemist, or whoever else was its discoverer. The silver that contains gold is put in this water, and from its former quiet state you will see it change as if forced to combat and breathlessly devour and consume that silver in itself and change it into water. This happens in a very short time and with very little help from the heat of the fire. All the gold that was united in the silver you will see like sand at the bottom, and when the water is taken off by decantation it will freely give you all the gold without any loss. Nor is it so ill-mannered as to fail to restore the silver to its place if you wish; and though it seems to have consumed and spoiled it as it was before, it returns it to you without loss. Since the process of this art is a very useful thing for anyone who knows

Jan 1, 1942

By J. T. Brown

AS far as could be ascertained, no one had previously investigated the creep strength of silicon poly-crystals. Literature has appeared showing evidence for plastic deformation in silicon single crystals and whiskers.*1"6 Also the fact that germanium, a material of similar crystal structure to silicon undergoes plastic deformation under stress at temperatures above about 60 pct of its melting temperature, has been known for some time.2"4'7 This investigation was performed for the purpose of determining the strength and ductility of silicon polycrystals under creep conditions that would give fairly long times to rupture. PROCEDURE The silicon specimen blanks were obtained by first placing granulated transitor grade silicon (99.999 + pct pure) in a silica crucible. The crucible was surrounded by a graphite susceptor, and induction heating was used for melting the silicon in a vacuum furnace. Blank specimens were formed by freezing molten silicon onto a polycrystalline seed of silicon in a vacuum furnace. The seed was attached to a motor driven revolving rod. As silicon solidified, this rod was gradually withdrawn from the melt. A shape with a contracted center section was obtained by varying the rate of withdrawal from the melt. Specimens for the creep-rupture tests were ground from these "pulled" blanks. Creep-rupture tests were performed in spring loaded machines under constant load at 1800" and 2000° F. RESULTS AND DISCUSSION A test specimen which was sectioned longitudinally is shown in the photomacrograph in Fig. 1. Very little deformation has taken place in the portion of the specimen shown, however, slip lines from several slip systems within the same grain, and deformation band formation was seen. The elongated appearance of the grains is due to the method of growing the specimens. One of the most interesting aspects of the results obtained from the creep-rupture tests was the high strength and the accompanying large amount of ductility. The data obtained is listed in Table I which shows the stress to rupture in 100 hr at 2000°F is between 8000 and 9000 psi. This indicates that silicon's strength at 2000°F is about equal to that of the best commercial super-alloys. It is important to mention that silicon has less than 1/3 the density of iron-, nickel-, and cobalt-base alloys. The usual type alloys for high-temperature applications

Jan 1, 1960

By John M. Hartman

The high temperature of the blast of modern furnaces renders it desirable that the pipe conveying the blast into the furnace crucible shall transmit and radiate as little heat as possible. To accomplish this, the pipe shown in the accompanying sketch was devised and patented. It consists of a slide-valve, leg-pipe, and belly-pipe, which are held together and to the tuyere by a system of levers and links. The slide-valve is superior to the old throttle-valve. The legpipe is formed of two thicknesses of wrought-iron pipe, with a space of half an inch filled in with clay and brick. The belly-pipe is made in the same way as the leg-pipe, and terminates in a globe face to suit the tuyere. The quarter turn is made extra thick, of cast iron, and the cap on the end is lined with clay also. The catches, A, B, C, are merely for convenience in putting the pipe together. The joints D and E are globe faces, and allow the pipe to adjust itself to any angle. The eye-piece is made of violet glass, which cuts off the glare from the bright coals in the furnace and allows a close examination of the interior, so that any water dropping or vapor can be detected. The glass does not become coated with dirt, like mica. Since good running of furnaces is shown by a bright tuyere, it is necessary to have a good eye-piece to examine them. To detach the pipe, a man lifts the weights, the side rods are then slipped off the bell crank under the quarter turn, the link under the belly-pipe is unhooked, and the pipe carried away. The same process is reversed to put the pipe together. The nozzle is changed by taking off the cap, G, drawing the nozzle through the belly-pipe, and inserting another. In this way the change can be made quickly, without taking down the pipe. On the old tuyere pipe bolts with brass nuts were used, which burned up and gave trouble. In other cases key-bolts were used, making it difficult to adjust the pipe. Bolts make too rigid a joint, and there is no provision for movement from contraction or expansion. As the temperature of the blast increases there is more expansion, and where rigid joints are

Jan 1, 1879

By R. W. Smith, G. W. Delamore, J. A. Spittle

RECENT work by the authors1 has demonstrated that the crystals constituting the equiaxed zone in small ingots originate, on quenching, in the chilled liquid. Whether any partial remelting2 takes place of the den-drites nucleated in the chilled region was not examined. However, the claim3 that this normally occurs, leading to crystal multiplication, has been disputed.4 Thus, for an equiaxed zone to form in the central region of an otherwise columnar ingot, it is necessary to transport crystallites from the chill zone to this region. In view of the work of Uhlmann et al.,5 it was considered desirable to examine the transport process further. Experimental Technique and Results. In the earlier experiments by the authors.1 a stainless-steel crucible 17/8 in. diam, 41/2 in. high, ad containing an alloy of A1-4 wt pct Cu, was quenched from 660°C into a bath of Wood's metal maintained at 100°C. Under these conditions a central zone of equiaxed crystals was obtained. However, if a 2250-G unidirectional magnetic field was applied for 2 sec immediately following the instant of quenching, or subsequently, the equiaxed zone did not appear. Careful thermal analysis showed that the short application of the field had virtually no effect on the thermal conditions of the melt. It thus appeared that the crystallites which were ultimately to grow large enough to form the equiaxed zone existed in the liquid immediately ahead of the interface, occlusion being prevented by the convective fluid flow induced by freezing from the walls of the cylinder. When this relative movement was prevented by the Lorenz forces induced by the application of the magnetic field, the crystallites were caught up in the rapidly advancing dendrite solid-liquid interface. To test this assumption, a small ingot of super-purity aluminum was partially melted and poured into a heated stainless-steel mold which was then immediately quenched into molten Wood's alloy. The resulting structure is shown in Fig. 1, and consists of columnar grains with a central fine-grained zone. Thus the unmelted solid present at the beginning of solidification had been transported ahead of the columnar interface. Discussion. There appears to be little or no information available on the interaction of suspended particles with a metallic solid/liquid interface. However, some information is available for transparent organic sys-

Jan 1, 1969

By Charles Himrod

In presenting this paper it is not intended to enter into any discussion of the theory of the blast-furnace, but simply to give the results of a number of determinations of CO and CO 2 in furnace gases, and some conclusions arrived at, and the result of an experiment made in hopes of increasing the production of CO 2. In the first table, on page 198, is given the averages of a number of analyses of gases of different furnaces, and in the second, of two stacks of different sizes under varying circumstances. The conclusions arrived at as to what influences the production of CO2 are as follows: lst,. Kind of fuel. Bituminous coal not permitting the formation of as much CO, as coke. 2d. Kind of ores. Rolling-mill cinder being much less favorable to formation of CO2 than hematite ores, magnetites probably less than hematites, but more than cinder. 3d. Length of time of contact of gases with ore. Small furnaces and too rapid driving both waste fuel by riot allowing enough time for conversion of CO into CO2. 4th. The temperature of blast. The hotter the greater the quantity of CO2. 5th. Regularity of passage of stock through the furnace. The hanging and dropping of the stock, however slight, seems to pack it more solidly in the hearth, increases the resistance to the blast, and decreases the quantity of CO2. These are the most common causes noticed which influence the production of CO2, unless we except the one that might be considered the greatest of all, the one that has spoiled so many tons of iron, and the amiability of so many furnacemen, the one most dreaded, the great unknown. It would seem a self-evident proposition that the better the contact of the gases with the ore and the less with the fuel, the greater would be the amount of CO2 produced. To prolong the contact of gas with the ore furnaces are enlarged with advantage, and pains are taken to charge the stock in such a manner as will best promote it. Still, with furnaces of most approved construction and most skilful manipulation, the gases leave the furnace so rich in CO, that not half the heating power of the fuel is obtained, and the highest

By F. S. Buffington, Morris Cohen

THERE is little quantitative information available concerning the effect of applied stress, in both the elastic and plastic ranges, on diffusion kinetics. Accordingly, a program has been undertaken to determine the rate of self-diffusion in high purity iron, with the specimens subjected to stress during the course of diffusion. Results are reported here for body-centered cubic iron at a diffusion temperature of 890°C. The iron used was 99.97 pct Fe, the principal impurities being 0.002 pct C, 0.008 pct 0, and 0.02 pct Si. The surface-decrease method of self-diffusion analysis was employed, and Fe55 Mn x-radiation, 2.9 years half-life) was the tracer element. Details of specimen preparation and equipment are given elsewhere.' Disks of the high purity iron, % in. diam x 1/4 in. thick, were annealed at 890°C for 18 hr in dry hydrogen to produce large grains of a ferrite. The faces of the disks were then surface ground, and possible grinding stresses were relieved by annealing at 890 °C for 45 min in vacuum. A layer of radioactive iron 0.00186 cm thick was electroplated on one face of each disk. The self-diffusion coefficient was calculated from the ratio of the radiation intensities emanating from each of these faces, as measured before and after diffusion.' The heating was carried out in a vacuum furnace (10-5 mm Hg) controlled to ±1.5°C. The specimens were loaded in compression between two quartz disks during the diffusion runs by means of a lever system operating through a vacuum seal. Thus one quartz disk was pressed directly against the radioactive face of the specimen, minimizing the vapor loss of radioactive iron. Steady-state creep occurred in all instances where permanent deformation could be detected, but the specimens did not exhibit appreciable transverse barreling until natural strains of 0.2 to 0.3 were attained. Essentially, the diffusion took place under uniaxial stress. The plastic strain in each case was obtained at the diffusion zone by measuring the diameter d there before and after the run: e = 2 In — do Let Du equal the self-diffusion coefficient which would have prevailed at the given temperature if no stress had been applied. This was calculated from the temperature-dependence equation which had been previously determined: —59,800 D, = 6.2 exp ( I sq cm per sec* [I]

Jan 1, 1953

By John M. Hartman

THE high temperature of the blast of modern furnaces renders it desirable that the pipe conveying the blast into the furnace crucible shall transmit and radiate as little heat as possible. To accomplish this, the pipe shown in the accompanying sketch was devised and patented. It consists of a slide-valve, leg-pipe, and belly-pipe, which are held together and to the tuyere by a system of levers and links. The slide-valve is superior to the old throttle-valve. The leg-pipe is formed of two thicknesses of wrought-iron pipe, with a space of half an inch filled in with clay and brick. The belly-pipe is made in the same way as the leg-pipe, and terminates in a globe face to suit the tuyere. The quarter turn is made extra thick, of cast iron, and the cap on the end is lined with clay also. The catches, A, B, C, are merely for convenience in putting the pipe together. The joints D and E are globe faces, and allow the pipe to adjust itself to any angle. The eye-piece is made of violet glass, which cuts off the glare from the bright coals in the furnace and allows a close examination of the interior, so that any water dropping or vapor can be detected. The glass does not become coated with dirt, like mica. Since good running of furnaces is shown by a bright tuyere, it is necessary to have a good eve-piece to examine then. To detach the pipe, a man lifts the weights, the side rods are then slipped off the bell crank under the quarter turn, the link under the belly-pipe is unhooked, and the pipe carried away. The same process is reversed to put the pipe together. The nozzle is changed by taking off the cap, G, drawing the nozzle through the belly-pipe, and inserting another. In this way the change can be made quickly, without taking down the pipe. On the old tuyere pipe bolts with brass nuts were used, which burned up and gave trouble. In other cases key-bolts were used, making it difficult to adjust the pipe. Bolts make too rigid a joint, and there is no provision for movement from contraction or expansion. As the temperature of the blast increases there is more expansion, and where rigid joints are

Jan 1, 1879

By E. A. Calnan, B. E. Williams

IN the development of a new treatment for the prediction of deformation textures,'-' it was noted that for no metals are there experimentally determined tension textures with which the predictions may be compared. There is a considerable knowledge of drawing textures and previous workers have been content to consider these as equivalent to tension textures for the purposes of comparison. It is shown, however, in the new treatment that the tension and drawing textures are not necessarily identical, the radial compression exerted by the dies in the drawing operation producing some modification of the tension texture. In particular for the face-centered cubic metals it is predicted that for drawing the final texture should be [1ll] with a spread towards [211] (a more detailed derivation of this texture has been made by Calnan3). This has been amply confirmed by experiment, see Hibbard.6 For the pure tension case, however, the treatment predicts intermediate [1ll] and [loo] textures leading to a [211] end-point, while all previous treatments have predicted the final texture as [1ll] with in some cases an additional [loo] component. Thus evidence that the pure tension end-point is the [211], or at least that [1ll] and [l00] are not the final textures, should provide a valuable test of the new treatment. Accordingly some experiments were made on aluminum. Three aluminum specimens were examined in detail, one of cold-rolled high purity rod (99.99 pct), specimen A, and two of commercial extruded rod of purity 99.4 pct, specimens B and C. The initial annealing treatments were: A, 1½ hr at 400°C; B, 2 hr at 400°C; C, 1½ hr at 650°C. The principal difficulty is that of obtaining sufficient elongation before fracture occurs. This was overcome to some extent by giving a softening heat treatment, 1 hr at 300°C, after each 15 pct of extension. Vickers hardness measurements gave values before and after the softening treatment of about 30 and 28, respectively, in comparison with the initial value of about 19 corresponding to fully annealed material. From recent observations in this laboratory it is concluded that this small recovery corresponds to a polygonization process rather than recrystallization proper and consequently the preferred orientation is unaffected. At the higher extensions, however, some slight necking of the specimens took place and it was necessary to turn them down to a uniform cross-section before

Jan 1, 1953

By Dubois Eastman

BEHIND the contrasting liquid-fuel technologies of Germany and the United States lie the basic differences of scarcity and abundance. The chemists and engineers of each nation have developed processes that accommodate available raw materials. In the United States, processing is based on an abundant supply of petroleum, which is refined into a variety of fuels and lubricants. Germany has little indigenous petroleum but has a readily available supply of coal that can be converted into liquid fuels and lubricants. As a result, in Germany several basic processes have been developed for the conversion of coal into synthesis gas (carbon monoxide and hydrogen). In turn, this gas is processed into products. As a normal function of its researches into petroleum processing, the petroleum industry in the United States has made careful studies of various conversion and synthesis techniques. A number of oil companies are carrying out independent development programs with the aim of synthesizing hydro- carbon products that can be marketed at a price that will compete with the price of refined petroleum products. American oil companies hope to perfect synthesis processes that will directly benefit the consumer. A good example of progress in these terms is the synthesis plant at Brownsville, Texas, which is based on the conversion of natural gas to synthetic fuels and other valuable products. When this plant is operated at near capacity, it is expected that the products will be able to compete favorably for the consumer dollar. The complete gasification of coal is a technique well rooted in history. As a controlled process on a small scale, it goes back centuries. As a practical technique on a commercial scale, it dates back to 1839, when "producer gas" appeared in Germany for limited industrial use. By 1873, "water gas," or "city gas" as it is sometimes called, was being manufactured commercially in the United States for use in heaters and stoves. The water-gas process was the cornerstone for modern synthesis. To older methods that were concerned only with carbon and oxygen reactions, it added hydrogen by means of steam. Thus far the goal of conversion was to produce gas for heating, lighting, industrial use, and cooking. The long step forward to synthesis was made in 1927, when Germany started to make gasoline from coal by means of the revolutionary Bergius hydrogenation process. A year earIier, Franz Fischer and Hans Tropsch had announced their process, which finally reached the

Jan 1, 1953

By S. W. Kessler, R. B. Pond

Metal specimens were solidified through a measured thermal gradient so a free surface and the liquid-solid interface could be examined. A line structure was observed on the surface and a hexagonal structure on the interface. A model to explain these forms is proposed. NUMEROUS observations of the dendrite form have been made both in nonmetallic and metallic systems. From these, extrapolations have been made as to the probable dendrite form in pure metals. Observations of the dendrite form in pure metals, nevertheless, have been scanty. In general, these observations have been made on the skeleton dendrite after the mother liquid has been drained from around it, and a mechanism of the formation of the dendrite has been postulated from this solid form. Recent investigations have been conducted in an endeavor to make a study of the formation of the dendrite in several pure metals and the effect of several variables on this mechanism and final form. For these investigations, an apparatus was designed and constructed as shown in Fig. 1. It consists of a talc block containing a half-cylindrical depression, the end of which terminates in the conical recess of a copper block having an external attachment for cooling. A heating coil extends the length of the mold just beneath the lower limits of the cavity. The entire cavity for holding metal is coated with a thin film of graphite. Six thermocouples are equally spaced in the cavity and under the graphite, and six microammeters indicate the temperatures at the particular thermocouple stations. Readings were taken of all meters at the same instant time measurements were taken by photographing the panel of microammeters and a stop watch which was started at the beginning of the run. It was possible with this apparatus to solidify metals through a measured thermal gradient and to observe the progression of the liquid-solid interface with time by following the formation of the dendrite markings in the surface of the solid material. These

Jan 1, 1952

By Morris Cohen

WITHIN the past two years, a number of publications have called attention to the double peaks, or stages, that appear in the hardness and strength curves of certain aging alloys. The author has shown the existence of double hardness peaks during the aging of a high-purity silver-copper alloy;' and on the basis of electrical resistance, microscopic, dilation and lattice-parameter measurements, he concluded that the initial hardness peak occurs prior to precipitation while the secondary hardening is due to precipitation. It was suggested that the general mechanism of age-hardening involves two consecutive processes, the first consisting of nucleus or knot' formation, and the second consisting of actual precipitation and particle growth. It was further held that the two stages are interdependent, but because of nonuniform precipitation they may overlap each other to an extent that increases as the aging temperature is raised. At high aging temperatures, the effect of the first stage cannot be detected because of the rapid occurrence of precipitation. . The general theory of age-hardening recently presented by Dr. M. L. V. Gayler3 is in close agreement with the picture outlined above. With reference to work done on duralumin, copper-beryllium and copper-silver alloys, Dr. Gayler also concluded that age-hardening takes place in two consecutive steps: first, diffusion (in which the solute atoms migrate to certain crystallographic planes), and then precipitation. However, W. L. Fink and D. W. Smith4 have shown that the double aging peaks that appear in the strength curves of high-purity aluminum-copper alloys may be explained without recourse to pre-precipitation phenomena. By means of very careful metallographic technique, Fink and Smith demonstrated that during aging the precipitation takes place at an accelerated rate along the grain boundaries and slip planes as a result of the plastic deformation caused by the drastic quench from the solution heat-treatment temperature. † The general precipitation occurs at a

Jan 1, 1938