Search Documents

By Alexander Field

THE rate of elimination of carbon largely controls the time required to make a heat of steel by the basic open-hearth process and to an important degree determines the cost of refining. Practical experience has led to the generally accepted belief that the use of slags relatively high in iron oxide, such as are required to bring about rapid refining, leads to a certain sacrifice of quality in the product. As a consequence, a compromise must be made between the exceedingly slow rate of carbon drop which would correspond to the ideal case and the rapid rate which would best satisfy the condition of minimum cost. An increase in rate of refining necessarily implies an increase in the concentration of iron oxide dissolved in the metal. However, even for the infinitely slow rate that corresponds to slag-metal equilibrium, the metal would contain a certain definite concentration of dissolved iron oxide. It is a matter of great practical importance, therefore, to determine the quantitative relation between the minimum or equilibrium concentration of iron oxide in the metal and the higher concentrations which must actually obtain in practice. The present paper is devoted to the development of certain equations, derived from the established laws of physical chemistry, which will enable this relation between rate of refining and the degree of oxidation of the metal bath to be computed from operating data. No attempt is made to exhaust the possibilities of this general method of treatment. In considering rate of refining, attention is mainly confined to rate of carbon elimination. However, the equations are of a more general nature and their application may readily be extended. The results of the preliminary calculations given herein indicate that increased rate of refining may have a decided effect in increasing the concentration of iron oxide dissolved in the metal. The uncertainty. which attaches to the calculated value for this relationship arises in part from probable errors in experimental data on which the calculations are based, and in part from the lack of complete or favorably disposed information on basic open-hearth practice.

Jan 1, 1928

By J. Bruce See

INTRODUCTION This symposium at Cu 2019 has been organised to honour and celebrate the career and achievements of Dr Phillip John Mackey, an internationally recognised expert in the production of non-ferrous metals, especially copper and nickel smelting and refining. Phillip was born in Epping, a suburb of Sydney, New South Wales, Australia on 19 April 1941 and is one of 4 children of Gilbert and Philomena (nee Bartlett) Mackey. After completing Primary School in Epping, he attended Marist Brothers High School in Eastwood, Sydney and graduated in 1957 as the Dux of the School. Phillip’s father, being on the staff of the Sydney Technical College, in Ultimo, Sydney had the opportunity in the early 1950s to meet the late Professor Sir Rupert Myers, Foundation Professor of the School of Metallurgy at the New South Wales University of Technology (later called the University of New South Wales or UNSW). Gilbert Mackey was impressed by the new young Professor of Metallurgy and encouraged his son to study metallurgy - at the time an expanding industry in post-war Australia. EDUCATION AT THE UNIVERSITY OF NEW SOUTH WALES Phillip commenced at UNSW in 1958, graduating with honours in 1963. His undergraduate education and training included a few years of part-time study while working at British Motor Corporation on sheet metal forming of car bodies. At University Phillip developed his talent for teamwork. He was a contributing writer to the University newspaper, Secretary of the UNSW Students’ Union and was active in the UNSW Metallurgical Society and co-editor in 1963 of “Metallurgical Review,” the annual journal of the UNSW Metallurgical Society. His diverse interests and curiosity about the world around him were likely nourished while at University. Upon completing his Bachelor’s degree, Phillip was awarded a Commonwealth of Australia Postgraduate Research Scholarship. He began his PhD in 1964 on the thesis topic “Studies in Heat Transfer between Dispersed Liquid Metals and Gaseous Atmospheres” working under the supervision of then Associate Professor Noel Warner, an outstanding Professor at the University. Professor Warner is now an Emeritus Professor at the University of Birmingham and is internationally respected for his pioneering theoretical and practical work on established and innovative smelting processes.

Jan 1, 2019

By W. L. Finlay

Size effects in quenching steel are particularly prominent and well recognized because of the existence of a critical cooling rate separating nuclea-tion and growth transformations, as exemplified by the formation of pearl-ite, from the shear type of transformation characterizing the martensite reaction. The absence of a similar, sharply demarcating cooling rate is characteristic of precipitation hardening systems and size effects in these are correspondingly less prominent. This paper is concerned with a size effect in high-purity, precipitation-hardenable alloys which appears not to have been recognized previously. This effect is believed to result from the thermal fluctuations which inevitably occur in quenching a specimen of finite size into a cooling liquid rather than from the existence of a critical cooling rate. QUENCHING "ANOMALIES" The precipitation hardening literature contains many references to so-called anomalous quenching and aging results. By "anomalous", investigators usually meant that their alloys did not consistently harden on aging after quenching according to some anticipated pnttern: not infrequently virtually no age hardening occurred with compositions known to be precipitation-hardenable. Perhaps the most prominent series of anomalies was reported over a 15-year period by Gayler and coworkers on aluminum-copper.l,2,3,4 Working with silver-rich copper alloy, Cohen5 secured some very interesting Rockwell F hardness changes of from 1-5 Rockwell points between the first peak and valley. Fink and Smith borrowed one of Cohen's specimens and, following his heat treatment and quenching practice to the letter, secured6 very different results in which only one peak was obtained and in which the hardness level at the aging lime of Cohen's first peak was 20 Rockwell F points higher. Fink and Van Horn7 encountered serious deviations in age-hardening high purity aluminum-zinc alloys. They stated that "the discrepancies were larger than might be expected from possible experimental errors in the Brinell readings." Geisler, Barrett and Mehl8 likewise encountered anomalous hardening results in aluminum-silver alloys, securing quite different age-hardening curves from two identical specimens. They stated that "the treatments of these samples had been the same, so that the different behaviors could be attributed only to accidental variations in the quenching practice."

Jan 1, 1950

By J. Chipman, J. C. Fulton

Reduction of silicon from blast-furnace-type slags by carbon-saturated iron is a very slow reaction even under conditions of rapid stirring. Equilibrium under atmospheric pressure of carbon monoxide was approached from both sides, and the silica-silicon relation was established at temperatures of 1425º to 1700°C for slags containing up to 20 pct Al2O3. Silicon carbide is formed by reaction of graphite with high silica slags and the conditions for its formation were determined. Activities of SiO2 and of CaO in their binary solutions at 1600°C were determined. The effects on the activity of SiO2 were established for additions of 10 to 20 pct AI2O3 and of 10 pct MgO. STUDIES of chemical reactions between blast-*>-5 furnace slags and metal have been focussed on the transfer of sulphur from metal to slag. The important role which silica reduction plays in this process' has led to a study of the transfer of silicon from slag to metal and the equilibrium represented by the equation SiO2 (in slag) + 2C (graphite) = Si + 2CO (g). [I.] The authors2 have published an account of the experimental method employed in attacking this problem and of three series of experimental results at 1600°C. This paper contains data on some additional compositions and extends the observations to cover the temperature range 1425° to 1700°C. The data are used to determine the activity of silica in the slags. As in the earlier experiments, the atmosphere was carbon monoxide which flowed through the furnace at 150 ml per min. In certain heats designated in the tables and figures, the gas was bubbled through the melt using a graphite tube. The latter increased in porosity during a run and in some cases bubbling ceased as indicated by cessation of surging. Some results were discarded for this reason. Experimental Results The new data are shown in Tables I through V and both old and new data are plotted in Figs. 1

Jan 1, 1955

By A. J. Miller, G. R. Brophy

The Grossmann principle1 for the calculation of hardenability of steel from composition is attractive because of its simplicity. It postulates that the hardenability of a steel for any particular grain size may be expressed in terms of an ideal critical diameter, which is the product of an ideal critical diameter for a "pure" iron-carbon base multiplied by a succession of factors for each element of composition contained, including the incidentals. It infers that the multiplying factor for a given quantity of an element is constant for all combinations of composition. Gross-mann has stated that in the great majority of cases the experimental values of hardenability are found to be well within 10 per cent of the calculated values. The validity of the scheme has been confirmed in principle by Crafts and Lamont2,3 and by Kramer et al.4 Their results differ from the original in the magnitude of the effect of some elements but, since they accepted the product concept and followed its direction, it is to be ex~ected that similar results would be obtained. Crafts and Lamont, in their second Paper, recognized that the factor relations for manganese and nickel were not continuously linear, but beyond certain critical amounts increase sharply. Austin, Van Note and Prater6 demonstrated nonlinear relations between hardenability and alloy contents. Their curves for chromium, silicon, manganese and nickel were all convex upward to show decreasing incremental effects. They concluded that Grossmann's factors under-evaluate the hardening effect of low percentage additions of these elements, and overevaluate the larger additions. More recently W. Stevens has found that the factor method fails when applied to complex steels containing two or three principal alloying elements other than carbon. Multiplying factors derived from his results bear a complex relation to composition and are not constant for a given amount of an element as the base composition varies. C. A. Liedholm7 found that, using either the Grossmann or the Crafts-Lamont multiplying factor values, not only were the relative hardenabilities of two heats of S.A.E. 6130 chromium-vanadium steel

Jan 1, 1947

By Clarence W. Balke

Small buttons of fused tantalum have been produced by are fusion in a vacuum, by drawing an arc between sticks of pressed tantalum and a tantalum-faced water-cooled copper block. However, ingots of appreciable size can be produced only by the heat-treatment of bars pressed from powder. The following outline covering the production of finished bars of tantalum by the methods of powder metallurgy is also used for the production of columbium, taking into account the difference in the melting points of these two metals. Pressing the Powder With possibly a few exceptions, a pressing operation is one of the essential steps in the practice of powder metallurgy. In fact, the author's experience with a number of high-melting-point metals and with numerous types of hard carbide compositions has led him to believe that this operation is often one of the most important in the entire process, and frequently one of the most difficult to carry out in a satisfactory manner. Defects due to improper pressing can readily lead to a defective finished product. It is the author's opinion that rarely is a bar or other article pressed from metal powder in such a way that all parts of the piece are uniformly pressed. The nearest approach to uniformity of pressing is possibly attained when the powder is contained in a flexible receptacle, such as rubber, and is pressed under a liquid by hydrostatic pressure. However, this method is not generally applicable. Hydraulic pressing in steel dies where one or two punches are forced into the die must usually be resorted to. As the pressure in such a die is built up, the powder begins to cling to the walls of the die with a tenacity dependent upon the nature of the powder, and this results in a bridging action, so that the layers of powder adjacent to the moving punch are pressed more heavily than those further removed in the mass. Frequently, as the pressure is carried higher, there may be a mass slippage of the powder upon itself, with the result that slip cracks are formed within the pressed

Jan 1, 1938

By A. G. Suydam

Ancient as is the art of producing copper, so ancient is one of its eternal problems: refractories. Looking backward, in the light of present knowledge, clouded though it be, one cannot avoid a sense of profound respect for the patience, acumen and courage of those who have wrought so successfully despite difficulties, a more accurate understanding of which seems merely to accentuate. The problem of refractories arises from the necessity for constructing containers in which to bring natural ores into thermal solution in order to effect reduction and separation of the valuable metal content and free it of undesirable contamination while producing a waste slag. The very forces known to produce thermal solution of sufficient liquidity are necessarily destructive of exposed refractory linings in proportions varying inversely with thermal conductivity, directly with the porosity and ease of fluxing of the refractories used, and directly with the temperatures employed. Beyond this, mechanical forces are set up within the refractory lining incident to rapid heating or cooling, shrinkage at high temperatures, and unequal or excessive loading, that frequently pass the elastic limit, causing spalling or distortion. The effects of these forces are often accentuated by the necessity of providing at the same time as hot a bath and as cool a container as are consistent with fuel economy. Evolution in the Use of Refractories Clay Brick.—Fireclay and clay refractories had to yield wherever they were in contact with slags rich in basic oxides, first because of the combining power of those oxides with free silica and secondly because of the tendency of alumina to form either aluminates or alumina-silicates of varying complexity. Of no less importance, the incipient fusion point was low as compared with good clay brick of today, while the brick lacked strength at high temperatures. Expansion was slight, therefore it was difficult to make and maintain tight walls, roof, or bottom. However, the spalling tendency was low because of some of these properties and clay brick have retained their place in roasting furnaces, boiler furnace linings, and in the upper walls of some of the reverberatory types such as some refining, anode and wire-bar furnaces. They have served often and most efficiently for hot patching.

Jan 1, 1934

By L. H. Cadoff, L. M. Adelsberg

The layer growth method has been used to investigate the reaction kinetics of liquid titanium and hafnium with carbon and the [liq] - [liq + TiC] and [liq] - [liq + HfC] phase boundaries at temperatures above 1800°C. The equipment and experimental procedures used in this investigation are basically identical to those described in an earlier paper' on the Zr-C reaction. Temperature control, however, was improved significantly by connecting a Latronics Colo-Ratio automatic pyrometer and a controller to the power source. The subsequent temperature variations were ±10°C; previously ±20°C was obtained using manual controls. The absolute accuracy of the pyrometer, however, must be considered to be only ±40°C.* The spectrographic analyses of the materials used in this study are listed in Table I. The isothermal reactions of titanium (1800° to 2700°C) and hafnium (2300" to 3000°C) with carbon (graphite crucibles) resulted in the formation of carbon-saturated liquid metal and layers of Tic and HfC, respectively. The thicknesses of the carbide layers, determined from metallographic measurements at 100 times, as a function of carburization time and temperature are given in Figs. 1 and 2. At each temperature, parabolic growth behavior for these reactions was observed and could be expressed as x2 =Kpt, where X is scale thickness (corrected for heating and coolingL), Kp the parabolic growth constant, and t the isothermal carburization time. Values of Kp as a function of temperature for the carbides are shown in Fig. 3 and listed in Table 11. The growth constants are expressible as: kpTiC = 0.2 exp(-61,800/RT) sq cm per sec for Tic and Kp HfC = 2.62 exp(-95,300/RT) sq cm per sec for HfC. The liquidus phase boundaries were determined from metal samples treated in graphite crucibles for different times ranging from 4 to 100 min at each of the temperatures indicated in Table 11. Metallographic examination revealed that the carbide precipitates were distributed uniformly throughout the frozen metal matrices. This is attributed to the rapid cooling rates (800°C per min) and the small difference in density between the precipitated carbide and the liquid metal.

Jan 1, 1968

By W. F. Holbrook

In a previous paper1 a method for the measurement of the comparative desulphurizing power of slags was described and data were presented covering the range of likely slags containing up to 10 per cent MgO. In the present work the range is extended to include slags containing up to 20 per cent MgO, and the effect of temperature on 5 per cent and 15 per cent MgO slags over the range 1475' to 1525' C. is included. The method used was that described in the previous paper except that some of the temperature measurements were made with a noble-metal thermocouple instead of a tungsten-graphite thermocouple. Twelve-gram charges of 0.8 per cent sulphur-metal and 5-gram charges of slag were subjected to heating for 30 min. at a prescribed temperature. The charges were analyzed for sulphur content. For purposes of comparison, desulphurizing power is defined as the ratio of the percentage of sulphur found in the slag to that found in the metal. Six slag and metal charges were made coincidentally in 5/8in. holes in a section of an electrode graphite rod. One slag and metal charge was used as a control by means of which adjustment in the desulphurization value could be made for small variations in temperature and other factors. For convenient presentation of the data, the slags are arranged in groups in each of which one of the four main slag components is constant. Thus, the 15 per cent MgO slags are presented separately from those containing 20 per cent MgO. Slags with Magnesium Oxide Constant 15 Per cent Mg0.—The data on slags containing 15 per cent MgO cover a composition range of 24 to 50 per cent SiO2, 5 to 27 per cent A1203 and 24 to 53 per cent CaO. Variation in composition has been in steps of 2 per cent over much of the area. Because the change in desulphurization power is generally gradual with gradual change in composition, certain sections have been covered in steps of 4 per cent and even

Jan 1, 1938

By Richard Moldenke

So far as the quality of the product is concerned, the history of the production of pig iron for foundry purposes is one of constant retrogression. The steps in this deterioration began with cold-blast charcoal pig iron, then anthracite iron, coke iron; then gradually warm to hot-blast coke iron, with the charcoal furnaces also heating their blast to get greater tonnages, and finally the present-day hot-blast coke irons with scrap additions to the ordinary burden that, according to one European report, have gone as high as 65 per cent. Parallel with this quality retrogression is the enormous increase in furnace tonnages from about 15 to over 1000 tons per day in excep tional instances of modern practice. The key to this situation is economic pressure. The effect is a growing differentiation between furnace production for gray iron and malleable foundries and for the production of commercial steel. As the foundry is often compelled to draw upon the pig irons made for steel purposes, for economic reasons, whereas the steel industry does not draw upon foundry pig irons proper, the situation is resolving itself into one of grave consequence for the life of the gray-iron castings industry, and hence the intensive present-day feeling in foundry circles for rigid specifications to govern the quality of pig irons sold for foundry use. In the discussion of a paper on the use of scrap in the blast furnace held recently in the Institute, a very pertinent remark was made by one of the participating furnacemen, who confessed that "the things found wrong by the foundryman with his iron were beyond his depth." It may be added that those things are also beyond the depth of most foundrymen who, however, know from their results that they are getting poorer castings today with many pig irons than they did with those same brands in former years. Under the former fracture buying, the foundryman at least could select the strongest metal, as judged by the sledge, from various brands of similar fracture and pig section, and his results proved

Jan 1, 1927

By James Aston

THE origin of wrought iron may be taken as coincident with the earliest record of ferrous products. The limitations of primitive methods of manufacture undoubtedly resulted in a material conforming to the general characteristics of what we now classify as wrought iron. Iron has been known from prehistoric times. It is frequently mentioned in Egyptian literature, and some samples in the British Museum are believed to date from 3733 B. C. Iron instruments, tools and weapons were used in Greece in 1400 B. C., and in Assyria and. Italy in 1100 B. C. History records their use in Central and Western Europe in 1000 B. C. And in Styria and Carinthia before the Christian era. The noted Pillar of Delhi is generally assumed to date from 400 A. D. The use of iron was general in Europe in the Roman Empire, and heat treatment of weapons and tools was then practiced. All of this early iron was the result of direct reduction from the ore. It serves to illustrate the ease with which the extraction may be effected, and to point out the well known principle that a malleable product of relatively high purity may be produced from high-grade iron ore at temperatures well below the fusion point of-the metal. The fact is also emphasized that there is no novelty in the seemingly ideal and constantly recurring attempts to effect direct reduction. Economic and engineering considerations have been dominant factors in dictating today's two-step practice in the manufacture of wrought iron and steel. Bear' in mind that all of this history antedated the blast furnace, and a knowledge and use of cast iron. It was only in attempts to get greater output by use of shaft-type furnaces, that cast iron was produced in Germany in the period 1300 to 1400 A. D. This was the result of longer contact with the carbon of the fuel, and higher temperatures in the furnace. This period marked the beginning of the existing two-stage operation, involving as the second step the refining of the. cast iron to a malleable product. For a time this was effected in small hearths not unlike a blacksmith's forge.

Jan 10, 1926

By S. D. Dahlgren

The plasticity of unalloyed P plutonium was studied by evaluating the strain-rate-hardening exponent, m, in the equation Values of m up to 0.33 and tensile elongations up to 680 pct were obtained for ß plutonium formed directly from the a phase. Casl bars that were cycled and tested had lower flow stresses and higher values for than uncycled bars , hut their total plastic elongations were not as great as expected because of premature failure at voids formed during cycling. Flow stresses were higher and m was lower (m = 0.15) for 9 plutonzutn formed from the y phase. ThE strain-rate-hardening exponent for plastic flow of p plutonium was determined as a function of strain rate, test temperature, and heat-treating history, and it was related to the rather large plastic elongation found previously for some plutonium tensile samples. Gardner and ~ann' obtained tensile elongations of up to 620 pct for P plutonium samples which had been completely transformed from the low-temperature a phase to the P phase before testing. Such a large percentage elongation is unusual for unalloyed metals or single-phase alloys.' The a phase is stable below approximately 112°C and (3 is stable between approximately 112" and 190"c.~ Both phases have mono-clinic structures. A temperature of 160°C is 0.58 of the effective absolute melting point, 475°C) of the p phase. The effective melting point is obtained by considering the enthalpy and entropy changes associated with the higher-temperature phase transformations and it is not the same as the experimental melting point of the highest-temperature allotrope of unalloyed plutonium. Nelson, Bowman, and Bierlein observed a striking difference between the ductility, as well as other mechanical properties, of p plutonium formed from the next higher-temperature phase (y) and the ductility of /3 plutonium formed from the a phase. The total elongation of /3 plutonium formed from the y phase was less than 5 pct. Earlier, the creep rate of 13 plutonium formed from the a phase was shown to be 200 to 500 times faster than the rate for 0 formed from y for the same test temperature and stress.

Jan 1, 1969

By Edward W. Parker

This plant was built in 1907 at the Bankhead mines to manufacture briquettes by the Zwoyer process under license from the Zwoyer Fuel Go., of New York, N. Y. The building was constructed to contain two units, each of a capacity of 10 tons per hr.; one unit was installed at the time the building was constructed, and the second unit is now being built. The coal used is an anthracite, which is more friable than that of Pennsylvania, and, as a consequepce, a larger percentage of dust or waste is produced, which was formerly thrown upon the slack-pile as waste, but is now passed to the " dust-bin " in the breaker, from which it is conveyed to the briquette-plant. An average analysis of the coal, published by Lewis Stockett and 13. R. Warden,' is as follows: Per Cent. Moisture,.........0.50 Volatile,..8.00 Fixed carbon,... 83..50 Ash,.......8.00 Total,.100.00 Sulphur,.........0.40 per cent. Specific gravity,...... 1.40 Color of ash,.white Heat value,.......14,000 B.t.u. The plant is run under two 12-hr. shifts, the force consisting of 1 superintendent for both shifts, 1 engineer for each shift, 1 briquetter for each shift, 1 helper for each shift, 1 laborer cleaning up for each shift. In the pitch-melting house, 2 men are on duty for one shift. The steam for the engine is furnished from a central boiler-plant, which also supplies steam for the breaker, the electric light and power-plant, machinery-shop, and boiler-shop. During March, April, May, and half of June, in 1907, the

Jan 1, 1909

By K. M. Tait, M. M. McDonald

"An overview of the status of the development and application of Integrated Gasification Combined Cycle (IOCC) power generation is presented. Current projects in North America, Europe and Japan are described, together with the status of plans to apply the technology in Canada. A brief review of the technology is presented, including promising coproduction cycles and hybrid gasification fluid bed processes. The ability of the process to be modified for CO2 to be extracted for enhanced oil recovery or disposal is addressed. The environmental impact of IGCC technology is compared to those of other power generation technologies IntroductionDefinition and HistoryIntegrated Gasification Combined Cycle (IGCC) technology is a concept which has been around for about 50 years but has been generating increasing interest in the last 10 to 15 years. This paper focusses on coal as the feedstock for gasification. Other feedstocks used in gasification systems have included oil, biomass, tires and petroleum coke. IGCC technology integrates coal gasification with generation of electricity by means of a combined cycle system which fires the produced gas in the gas turbine. Figure 1 shows the basic components of an IGCC system which are the gasifier, the gas cleanup system and sulphur recovery plant, the gas turbine/generator set, the heat recovery steam generator (HRSG) and the steam turbine/generator set. The benefits of an IGCC system over a conventional Rankine Cycle pulverized coal (RCPC) fired system for the generation of electricity from coal are that the IGCC system has potential to have higher efficiency and lower emissions of NO., SO and CO2 per unit of power produced than the corresponding RCPC system."

Jan 1, 1994

By J. P. Coughlin

Gypsum plaster is calcium sulfate hemihydrate (CaS04-1/2H2O). There are two varieties, commonly designated as a and ß. The hydration setting) of this plaster involves the chemical reaction: CaS04?1/2H20(c) + 3/2H20(l) = CaSO4?2H20(c); that is, the hemihydrate combines with water to form the dihydrate. Many substances, when present as impurities, either in the hemihydrate or the water have influenced the rate of the hydration reaction. The objective of the Bureau of Mines work described in this report was to investigate the accelerating or retarding effects of small amounts of dissolved substances and to attempt to classify these effects upon a chemical basis. To eliminate competing effects, the work was conducted separately on the two varieties of hemihydrate; both were in highly pure form. (Commercial plasters usually are a mixture of the hemihydrates, with other substances present as impurities.) As the hydration reaction of each variety of hemihydrate evolves heat in amounts known from previous work, 5,6/ the authors decided to use calorimetric methods to follow the extent of the hydration reaction as a function of time. Two calorimetric methods were employed. One was designed to study the hydration reaction with a large water to plaster ratio and the other with a small water to plaster ratio (to simulate commercial practice in utilizing plaster).

Jan 1, 1959

By Otto Henry

THE purpose of this investigation was to determine the equilibrium diagram of the lithium-magnesium pair as a first step in studying the possible usefulness of these alloys as ultra-light structural materials. REVIEW OF THE LITERATURE The behavior of lithium towards magnesium was first investigated by Masing and Tammann.(I)? In order to prevent oxidation the alloys were made in iron tubes under an atmosphere of hydrogen; temperatures were measured with a glass-protected thermocouple. These investigators found that lithium and magnesium form two series of solid solutions separated by a miscibility gap between 85 and 95 per cent magnesium; that the alloys with 81 and 95 per cent magnesium showed a homogeneous structure under microscopic examination, while the alloy with 89 per cent magnesium contained two distinguishable crystallites; that the curve indicating the beginning of crystallization rises from the melting point of lithium to that of magnesium; and that no compounds of lithium and magnesium are formed. The equilibrium diagram was not plotted because no definite data were obtained for determining the solidus and the posi-tion of the miscibility gap in the solid state. The difficulties encountered in this investigation were: (1) that it was necessary to heat them as high as the melting point of magnesium in order to obtain homogeneous melts; at such temperatures the alloys attacked the glass protecting the thermo-couple; and (2) that at temperatures above 400° C. the lithium united

Jan 1, 1934

By E. F. Loiseau

In a paper on the manufacture of artificial fuel, read at the Philadelphia meeting of February, 1878, I enumerated the difficulties which I had to overcome before succeeding in the mixing of coal-dust and clay, the compressing of the same mixture, and the water-proofing of the lumps. The drying of the lumps, after leaving the press, was the remaining difficulty, and it mas expected that a plan devised by Dr. Charles N. Cresson, of Philadelphia, would enable us to dry the fuel as rapidly as it was moulded, and that a continuous production could in that way be obtained. The company was reorganized. The works were purchased by the new company at an assignee's sale, and the oven was modified, according to Dr. Cresson's plan. Anticipating a possible failure, I had prepared a plan by which I expected to be able to demonstrate that anthracite coal dust nixed with pitch, could be manufactured with our present machinery slightly modified ; so that after all, if we were compelled to give up the attempt to make fuel for domestic use, there was a possibility of succeeding in the manufacture of a good steam-fuel. The plan suggested by Dr. Cresson for drying the pressed lumps of coal-dust cemented with clay, did not work as well as we expected. It enabled us to dry more fuel than we did before, but it could not be made to dry more than one half of the lumps produced by the press. The plan mas abandoned, and I was authorized to experiment with coal-dust and coal-tar pitch. The cement which is used in Europe to conglomerate coal-dust is usually dry pitch, which is prepared by separating from the tar, at a temperature of 572' Fahrenheit, the volatile matters which it contains. Some manufacturers, however, employ crude tar, others, a rich tar, which has been cleared of 25 per cent. of its volatile substances, by heating it to 392' Fahrenheit. But with common tar very weak fuels are obtained, which do riot burn well, and give out a strong smell and a great deal of smoke ; it is also necessary to subject them to a baking process, in order to solidify them, and to eliminate the more volatile of the materials contained. This operation of course requires a special plant, the cost of which increases sensibly the price of manufacture, without counting the products

Jan 1, 1880

By E. F. Loiseau

IN a paper on the manufacture of artificial fuel, read at the Philadelphia meeting of February, 1878, I enumerated the difficulties which I had to overcome before succeeding in the mixing of coal-dust and clay, the compressing of the same mixture, and the water-proofing of the lumps. The drying of the lumps, after leaving the press, was the remaining difficulty, and it was expected that a plan devised by Dr. Charles M. Cresson, of Philadelphia, would enable us to dry the fuel as rapidly as it was moulded, and that a continuous production could in that way be obtained. The company was reorganized. The works were purchased by the new company at an assignee's sale, and the oven was modified, according to Dr. Cresson's plan. Anticipating a possible failure, I had prepared a plan by which I expected to be able to demonstrate that anthracite coal dust mixed with pitch, could be manufactured with our present machinery slightly modified ; so that after all, if we were compelled to give up the attempt to make fuel for domestic use, there was a possibility of succeeding in the manufacture of a good steam-fuel. The plan suggested by Dr. Cresson for drying the pressed lumps of coal-dust cemented with clay, did not work as well as we expected. It enabled us to dry more fuel than we did before, but it could not be made to dry more than one-half of the lumps produced by the press. The plan was abandoned, and I was authorized to experiment with coal-dust and coal-tar pitch. The cement which is used in Europe to conglomerate coal-dust is ,usually dry pitch, which is prepared by separating from the tar, at a temperature of 572° Fahrenheit, the volatile matters which it contains. Some manufacturers, however, employ crude tar, others, a rich tar, which has been cleared of 25 per cent. of its volatile substances, by heating it to 392° Fahrenheit. But with common tar very weak fuels are obtained, which do not burn well, and give out a strong smell and a great deal of smoke ; it is also necessary to subject them to a baking process, in order to solidify them, and to eliminate the more volatile of the materials contained. This operation of course requires a special plant, the cost of which increases sensibly the price of manufacture, without counting the products

Jan 1, 1880

By N. S. Stoloff, R. G. Davis

It is concluded from an X-ray stztdy that the formation of the hcp Mg3Cd superlattice is a nuclea-tion and growth reaction. A two-phase, ordered-plus-disordered, region is observed between 153" nnd 141"C. A maximum in the flow stress is observed both at temperature and in quenched specimens within the two-phase region. The peak arises fro112 the extra energy required to create antiphase boundary upon cutting the ordered regions. Hardening during isothermal annealing in Mg3Cd has been shown to be similar to the domain hardening in Cu3Au-type alloys in that up to the maximum the structure is ordered domains growing into a short range ordered matrix. The hardening is due to a combination of short range order strengthening and the strengthening produced when antiphase boundary has to be created. In a recent study1 of the effect of long-range order upon the mechanical properties and deformation modes of hcp Mg3Cd a comparison was made be- tween quenched (disordered) and slow-cooled (fully ordered) specimens. The most striking observations were that the disordered alloy yields at a much higher stress than the ordered alloy, and that there is a change in slip mode from primarily (_0001) ba_sal slip in the disordered state to (0001), {1010}, {1122}, and {l011} slip in the ordered state. The main purpose of the present work is to extend these observations to determine whether MgsCd exhibits a peak in flow stress at an intermediate degree of order, or at a critical domain size, as do other orderedstems. However, disagreement exists about the Mg3Cd order transformation with respect to: 1) the location of the critical temperature for order, 165°C or 153"~,' and 2) how the degree of order varies with temperature. Welber et a1.5 concluded from specific heat measurements that the formation of Mg3Cd is a second-order reaction with the degree of order a continuous function of temperature, while Moore and Raynor concluded that it is neither a first-order reaction, with the degree of order a discontinuous function of temperature, nor a second-order reaction. Consequently it was considered necessary to undertake an X-ray investigation into the change in degree of order and structure in the

Jan 1, 1964

By S. W. Zehr, G. S. Murty, W. A. Backofen

AN observation by Squires, Weiner, and phillipsl has stimulated interest in a mechanism of deformation at high temperature (above -0.5 of the absolute melting point) that is not usually thought to be involved in the creep of metals. They found precipitate-free or "denuded" zones along grain boundaries normal to the stress axis in tensile specimens of a hydrided Mg-1/2 wt pct Zr alloy after slow straining at 450° and 500°C. Their suggestion that the zones were a result of directional diffusion of magnesium atoms was supported with calculations from Harris and Jones2 which also tended to identify the process as Nabarro-Herring (N-H) creep3,4—a process that is characterized by Newtonian viscosity, with stress (o) directly proportional to strain rate (C), and one that proceeds by lattice diffusion. Material transport by diffusion along grain boundaries is an alternative basis for Newtonian viscosity, as demonstrated by Coble,5 and is favored over N-H creep for fine grain size and lower temperature.6 In either case, the strain rate sensitivity of flow stress, defined as m = d log o/d log E (which commonly appears in the empirical a = KEW), is unity. The experiments to be described here gave metallo-graphic indications of diffusional creep which were no less clear than those just cited, but the associated m (as measured by the method of Ref. 7) was much more like that of a Bingham material. For true Bingham behavior, (a — ao) E, where oo is an initial yield stress. Therefore, even if flow after yielding should occur by diffusional transport, m must increase from 0 as < is raised to reach unity only in the limit as One result is that the resistance to tensile necking conferred by Newtonian viscosity is lost, which would become increasingly apparent through the formation of more sharply defined necks as 6 is lowered. That trend appeared in these experiments. Most of the work was done on an extremely finegrained alloy of magnesium with -6 wt pct Zn and ½ wt pct Zr (Mg ZK60); the initial mean-intercept grain diameter, L, was 0.55 µ. Shown in Fig. l(a) is a germanium-shadowed carbon replica of the surface of a specimen that was coated with silicone oil,* heated to 270°C under a helium atmosphere, and then stretched locally -200 pct at an initial E = 3.3 x 10-5 sec-1. Under

Jan 1, 1969